[DPU PATCH 01/11] dt-bindings: msm/disp: remove unused dsi & panel bindings

[Rajesh Yadav <ryadav-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>]

DPU driver switched to existing upstream dsi driver
so removing the dsi-staging specific dsi and panel
bindings.

Signed-off-by: Rajesh Yadav <ryadav@codeaurora.org>
---
 .../devicetree/bindings/drm/msm/dpu-dsi.txt        | 102 ---
 .../devicetree/bindings/drm/msm/mdss-dsi-panel.txt | 772 ---------------------
 .../devicetree/bindings/fb/mdss-dsi-panel.txt      | 742 --------------------
 Documentation/devicetree/bindings/fb/mdss-pll.txt  | 103 ---
 4 files changed, 1719 deletions(-)
 delete mode 100644 Documentation/devicetree/bindings/drm/msm/dpu-dsi.txt
 delete mode 100644 Documentation/devicetree/bindings/drm/msm/mdss-dsi-panel.txt
 delete mode 100644 Documentation/devicetree/bindings/fb/mdss-dsi-panel.txt
 delete mode 100644 Documentation/devicetree/bindings/fb/mdss-pll.txt

diff --git a/Documentation/devicetree/bindings/drm/msm/dpu-dsi.txt b/Documentation/devicetree/bindings/drm/msm/dpu-dsi.txt
deleted file mode 100644
index 641cc26..0000000
--- a/Documentation/devicetree/bindings/drm/msm/dpu-dsi.txt
+++ /dev/null
@@ -1,102 +0,0 @@
-Qualcomm Technologies, Inc.
-
-mdss-dsi is the master DSI device which supports multiple DSI host controllers
-that are compatible with MIPI display serial interface specification.
-
-DSI Controller:
-Required properties:
-- compatible:           Should be "qcom,dsi-ctrl-hw-v<version>". Supported
-			versions include 1.4, 2.0 and 2.2.
-			eg: qcom,dsi-ctrl-hw-v1.4, qcom,dsi-ctrl-hw-v2.0,
-			qcom,dsi-ctrl-hw-v2.2
-			And for dsi phy driver:
-			qcom,dsi-phy-v0.0-hpm, qcom,dsi-phy-v0.0-lpm,
-			qcom,dsi-phy-v1.0, qcom,dsi-phy-v2.0,
-			qcom,dsi-phy-v3.0
-- reg:                  Base address and length of DSI controller's memory
-			mapped regions.
-- reg-names:            A list of strings that name the list of regs.
-			"dsi_ctrl" - DSI controller memory region.
-			"mmss_misc" - MMSS misc memory region.
-- cell-index:           Specifies the controller instance.
-- clocks:               Clocks required for DSI controller operation.
-- clock-names:          Names of the clocks corresponding to handles. Following
-			clocks are required:
-			"mdp_core_clk"
-			"iface_clk"
-			"core_mmss_clk"
-			"bus_clk"
-			"byte_clk"
-			"pixel_clk"
-			"core_clk"
-			"byte_clk_rcg"
-			"pixel_clk_rcg"
-- gdsc-supply:		phandle to gdsc regulator node.
-- vdda-supply:		phandle to vdda regulator node.
-- vcca-supply:		phandle to vcca regulator node.
-- interrupt-parent	phandle to the interrupt parent device node.
-- interrupts:		The interrupt signal from the DSI block.
-
-Bus Scaling Data:
-- qcom,msm-bus,name:		String property describing MDSS client.
-- qcom,msm-bus,num-cases:	This is the number of bus scaling use cases
-				defined in the vectors property. This must be
-				set to <2> for MDSS DSI driver where use-case 0
-				is used to remove BW votes from the system. Use
-				case 1 is used to generate bandwidth requestes
-				when sending command packets.
-- qcom,msm-bus,num-paths:	This represents number of paths in each bus
-				scaling usecase. This value depends on number of
-				AXI master ports dedicated to MDSS for
-				particular chipset.
-- qcom,msm-bus,vectors-KBps:	A series of 4 cell properties, with a format
-				of (src, dst, ab, ib) which is defined at
-				Documentation/devicetree/bindings/arm/msm/msm_bus.txt.
-				DSI driver should always set average bandwidth
-				(ab) to 0 and always use instantaneous
-				bandwidth(ib) values.
-
-Optional properties:
-- label:                  String to describe controller.
-- qcom,platform-te-gpio:  Specifies the gpio used for TE.
-- qcom,dsi-display-active: Current active display
-- qcom,dsi-ctrl: handle to dsi controller device
-- qcom,dsi-phy: handle to dsi phy device
-- qcom,dsi-manager:       Specifies dsi manager is present
-- qcom,dsi-display:       Specifies dsi display is present
-- qcom,hdmi-display:      Specifies hdmi is present
-- qcom,dp-display:        Specified dp is present
-- qcom,<type>-supply-entries:		A node that lists the elements of the supply used by the
-					a particular "type" of DSI module. The module "types"
-					can be "core", "ctrl", and "phy". Within the same type,
-					there can be more than one instance of this binding,
-					in which case the entry would be appended with the
-					supply entry index.
-					e.g. qcom,ctrl-supply-entry@0
-					-- qcom,supply-name: name of the supply (vdd/vdda/vddio)
-					-- qcom,supply-min-voltage: minimum voltage level (uV)
-					-- qcom,supply-max-voltage: maximum voltage level (uV)
-					-- qcom,supply-enable-load: load drawn (uA) from enabled supply
-					-- qcom,supply-disable-load: load drawn (uA) from disabled supply
-					-- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on
-					-- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
-					-- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
-					-- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
-- qcom,mdss-mdp-transfer-time-us:	Specifies the dsi transfer time for command mode
-					panels in microseconds. Driver uses this number to adjust
-					the clock rate according to the expected transfer time.
-					Increasing this value would slow down the mdp processing
-					and can result in slower performance.
-					Decreasing this value can speed up the mdp processing,
-					but this can also impact power consumption.
-					As a rule this time should not be higher than the time
-					that would be expected with the processing at the
-					dsi link rate since anyways this would be the maximum
-					transfer time that could be achieved.
-					If ping pong split enabled, this time should not be higher
-					than two times the dsi link rate time.
-					If the property is not specified, then the default value is 14000 us.
-- qcom,dsi-phy-isolation-enabled:	A boolean property enables the phy isolation from dsi
-					controller. This must be enabled for debugging purpose
-					only with simulator panel. It should not be enabled for
-					normal DSI panels.
diff --git a/Documentation/devicetree/bindings/drm/msm/mdss-dsi-panel.txt b/Documentation/devicetree/bindings/drm/msm/mdss-dsi-panel.txt
deleted file mode 100644
index 66a564d..0000000
--- a/Documentation/devicetree/bindings/drm/msm/mdss-dsi-panel.txt
+++ /dev/null
@@ -1,772 +0,0 @@
-QTI mdss-dsi-panel
-
-mdss-dsi-panel is a dsi panel device which supports panels that
-are compatible with MIPI display serial interface specification.
-
-Required properties:
-- compatible:				This property applies to DSI V2 panels only.
-					This property should not be added for panels
-					that work based on version "V6.0"
-					DSI panels that are of different versions
-					are initialized by the drivers for dsi controller.
-					This property specifies the version
-					for DSI HW that this panel will work with
-					"qcom,dsi-panel-v2" = DSI V2.0
-- status:        			This property applies to DSI V2 panels only.
-					This property should not be added for panels
-					that work based on version "V6.0"
-					DSI panels that are of different versions
-					are initialized by the drivers for dsi controller.
-					A string that has to be set to "okay/ok"
-					to enable the panel driver. By default this property
-					will be set to "disable". Will be set to "ok/okay"
-					status for specific platforms.
-- qcom,mdss-dsi-panel-controller:	Specifies the phandle for the DSI controller that
-					this panel will be mapped to.
-- qcom,mdss-dsi-panel-width:		Specifies panel width in pixels.
-- qcom,mdss-dsi-panel-height:		Specifies panel height in pixels.
-- qcom,mdss-dsi-bpp:			Specifies the panel bits per pixel.
-					3  = for rgb111
-					8  = for rgb332
-					12 = for rgb444
-					16 = for rgb565
-					18 = for rgb666
-					24 = for rgb888
-- qcom,mdss-dsi-panel-destination:	A string that specifies the destination display for the panel.
-					"display_1" = DISPLAY_1
-					"display_2" = DISPLAY_2
-- qcom,mdss-dsi-panel-timings:		An array of length 12 that specifies the PHY
-					timing settings for the panel.
-- qcom,mdss-dsi-panel-timings-8996:		An array of length 40 char that specifies the 8996 PHY lane
-					timing settings for the panel.
-- qcom,mdss-dsi-on-command:		A byte stream formed by multiple dcs packets base on
-					qcom dsi controller protocol.
-					byte 0: dcs data type
-					byte 1: set to indicate this is an individual packet
-						 (no chain)
-					byte 2: virtual channel number
-					byte 3: expect ack from client (dcs read command)
-					byte 4: wait number of specified ms after dcs command
-						 transmitted
-					byte 5, 6: 16 bits length in network byte order
-					byte 7 and beyond: number byte of payload
-- qcom,mdss-dsi-off-command:		A byte stream formed by multiple dcs packets base on
-					qcom dsi controller protocol.
-					byte 0: dcs data type
-					byte 1: set to indicate this is an individual packet
-						 (no chain)
-					byte 2: virtual channel number
-					byte 3: expect ack from client (dcs read command)
-					byte 4: wait number of specified ms after dcs command
-						 transmitted
-					byte 5, 6: 16 bits length in network byte order
-					byte 7 and beyond: number byte of payload
-- qcom,mdss-dsi-post-panel-on-command:	same as "qcom,mdss-dsi-on-command" except commands are
-					sent after displaying an image.
-
-Note, if a short DCS packet(i.e packet with Byte 0:dcs data type as 05) mentioned in
-qcom,mdss-dsi-on-command/qcom,mdss-dsi-off-command stream fails to transmit,
-then 3 options can be tried.
-	1. Send the packet as a long packet instead
-				Byte 0: dcs data type = 05 (DCS short Packet)
-				Byte 0: dcs data type = 29 (DCS long Packet)
-	2. Send the packet in one burst by prepending with the next packet in packet stream
-				Byte 1 = 01 (indicates this is an individual packet)
-				Byte 1 = 00 (indicates this will be appended to the next
-					     individual packet in the packet stream)
-	3. Prepend a NULL packet to the short packet and send both in one burst instead of
-	   combining multiple short packets and sending them in one burst.
-
-Optional properties:
-- qcom,mdss-dsi-panel-name:		A string used as a descriptive name of the panel
-- qcom,mdss-dsi-panel-phy-timings:	An array of length 'n' char that specifies the DSI PHY lane
-					timing settings for the panel. This is specific to DPU DRM driver.
-					The value of 'n' depends on the DSI PHY h/w revision and parsing this
-					property properly will be taken care in the DSI PHY DRM driver.
-- qcom,cmd-sync-wait-broadcast:		Boolean used to broadcast dcs command to panels.
-- qcom,mdss-dsi-fbc-enable:		Boolean used to enable frame buffer compression mode.
-- qcom,mdss-dsi-fbc-slice-height:	Slice height(in lines) of compressed block.
-					Expressed as power of 2. To set as 128 lines,
-					this should be set to 7.
-- qcom,mdss-dsi-fbc-2d-pred-mode:	Boolean to enable 2D map prediction.
-- qcom,mdss-dsi-fbc-ver2-mode:		Boolean to enable FBC 2.0 that supports 1/3
-					compression.
-- qcom,mdss-dsi-fbc-bpp:		Compressed bpp supported by the panel.
-					Specified color order is used as default value.
-- qcom,mdss-dsi-fbc-packing:		Component packing.
-					0 = default value.
-- qcom,mdss-dsi-fbc-quant-error:	Boolean used to enable quantization error calculation.
-- qcom,mdss-dsi-fbc-bias:		Bias for CD.
-					0 = default value.
-- qcom,mdss-dsi-fbc-pat-mode:		Boolean used to enable PAT mode.
-- qcom,mdss-dsi-fbc-vlc-mode:		Boolean used to enable VLC mode.
-- qcom,mdss-dsi-fbc-bflc-mode:		Boolean used to enable BFLC mode.
-- qcom,mdss-dsi-fbc-h-line-budget:	Per line extra budget.
-					0 = default value.
-- qcom,mdss-dsi-fbc-budget-ctrl:		Extra budget level.
-					0 = default value.
-- qcom,mdss-dsi-fbc-block-budget:		Per block budget.
-					0 = default value.
-- qcom,mdss-dsi-fbc-lossless-threshold: Lossless mode threshold.
-					0 = default value.
-- qcom,mdss-dsi-fbc-lossy-threshold:	Lossy mode threshold.
-					0 = default value.
-- qcom,mdss-dsi-fbc-rgb-threshold:	Lossy RGB threshold.
-					0 = default value.
-- qcom,mdss-dsi-fbc-lossy-mode-idx:	Lossy mode index value.
-					0 = default value.
-- qcom,mdss-dsi-fbc-max-pred-err:	Max quantization prediction error.
-					0 = default value
-- qcom,mdss-dsi-h-back-porch:		Horizontal back porch value in pixel.
-					6 = default value.
-- qcom,mdss-dsi-h-front-porch:		Horizontal front porch value in pixel.
-					6 = default value.
-- qcom,mdss-dsi-h-pulse-width:		Horizontal pulse width.
-					2 = default value.
-- qcom,mdss-dsi-h-sync-skew:		Horizontal sync skew value.
-					0 = default value.
-- qcom,mdss-dsi-v-back-porch:		Vertical back porch value in pixel.
-					6 = default value.
-- qcom,mdss-dsi-v-front-porch:		Vertical front porch value in pixel.
-					6 = default value.
-- qcom,mdss-dsi-v-pulse-width:		Vertical pulse width.
-					2 = default value.
-- qcom,mdss-dsi-h-left-border:		Horizontal left border in pixel.
-					0 = default value
-- qcom,mdss-dsi-h-right-border:		Horizontal right border in pixel.
-					0 = default value
-- qcom,mdss-dsi-v-top-border:		Vertical top border in pixel.
-					0 = default value
-- qcom,mdss-dsi-v-bottom-border:	Vertical bottom border in pixel.
-					0 = default value
-- qcom,mdss-dsi-underflow-color:	Specifies the controller settings for the
-					panel under flow color.
-					0xff = default value.
-- qcom,mdss-dsi-border-color:		Defines the border color value if border is present.
-					0 = default value.
-- qcom,mdss-dsi-panel-jitter:		Panel jitter value is expressed in terms of numerator
-					and denominator. It contains two u32 values - numerator
-					followed by denominator. The jitter configurition causes
-					the early wakeup if panel needs to adjust before vsync.
-					Default jitter value is 2.0%. Max allowed value is 10%.
-- qcom,mdss-dsi-panel-prefill-lines:	An integer value defines the panel prefill lines required to
-					calculate the backoff time of rsc.
-					Default value is 16 lines. Max allowed value is vtotal.
-- qcom,mdss-dsi-pan-enable-dynamic-fps:	Boolean used to enable change in frame rate dynamically.
-- qcom,mdss-dsi-pan-fps-update:		A string that specifies when to change the frame rate.
-					"dfps_suspend_resume_mode"= FPS change request is
-					implemented during suspend/resume.
-					"dfps_immediate_clk_mode" = FPS change request is
-					implemented immediately using DSI clocks.
-					"dfps_immediate_porch_mode_hfp" = FPS change request is
-					implemented immediately by changing panel horizontal
-					front porch values.
-					"dfps_immediate_porch_mode_vfp" = FPS change request is
-					implemented immediately by changing panel vertical
-					front porch values.
-- qcom,min-refresh-rate:		Minimum refresh rate supported by the panel.
-- qcom,max-refresh-rate:		Maximum refresh rate supported by the panel. If max refresh
-					rate is not specified, then the frame rate of the panel in
-					qcom,mdss-dsi-panel-framerate is used.
-- qcom,mdss-dsi-bl-pmic-control-type:	A string that specifies the implementation of backlight
-					control for this panel.
-					"bl_ctrl_pwm" = Backlight controlled by PWM gpio.
-					"bl_ctrl_wled" = Backlight controlled by WLED.
-					"bl_ctrl_dcs" = Backlight controlled by DCS commands.
-					other: Unknown backlight control. (default)
-- qcom,mdss-dsi-bl-pwm-pmi:		Boolean to indicate that PWM control is through second pmic chip.
-- qcom,mdss-dsi-bl-pmic-bank-select:	LPG channel for backlight.
-					Required if backlight pmic control type is PWM
-- qcom,mdss-dsi-bl-pmic-pwm-frequency:	PWM period in microseconds.
-					Required if backlight pmic control type is PWM
-- qcom,mdss-dsi-pwm-gpio:		PMIC gpio binding to backlight.
-					Required if backlight pmic control type is PWM
-- qcom,mdss-dsi-bl-min-level:		Specifies the min backlight level supported by the panel.
-					0 = default value.
-- qcom,mdss-dsi-bl-max-level:		Specifies the max backlight level supported by the panel.
-					255 = default value.
-- qcom,mdss-brightness-max-level:	Specifies the max brightness level supported.
-					255 = default value.
-- qcom,mdss-dsi-interleave-mode:	Specifies interleave mode.
-					0 = default value.
-- qcom,mdss-dsi-panel-type:		Specifies the panel operating mode.
-					"dsi_video_mode" = enable video mode (default).
-					"dsi_cmd_mode" = enable command mode.
-- qcom,5v-boost-gpio:			Specifies the panel gpio for display 5v boost.
-- qcom,mdss-dsi-te-check-enable:	Boolean to enable Tear Check configuration.
-- qcom,mdss-dsi-te-using-wd:		Boolean entry enables the watchdog timer support to generate the vsync signal
-					for command mode panel. By default, panel TE will be used to generate the vsync.
-- qcom,mdss-dsi-te-using-te-pin:	Boolean to specify whether using hardware vsync.
-- qcom,mdss-dsi-te-pin-select:		Specifies TE operating mode.
-					0 = TE through embedded dcs command
-					1 = TE through TE gpio pin. (default)
-- qcom,mdss-dsi-te-dcs-command:		Inserts the dcs command.
-					1 = default value.
-- qcom,mdss-dsi-wr-mem-start:		DCS command for write_memory_start.
-					0x2c = default value.
-- qcom,mdss-dsi-wr-mem-continue:	DCS command for write_memory_continue.
-					0x3c = default value.
-- qcom,mdss-dsi-h-sync-pulse:		Specifies the pulse mode option for the panel.
-					0 = Don't send hsa/he following vs/ve packet(default)
-					1 = Send hsa/he following vs/ve packet
-- qcom,mdss-dsi-hfp-power-mode:		Boolean to determine DSI lane state during
-					horizontal front porch (HFP) blanking period.
-- qcom,mdss-dsi-hbp-power-mode:		Boolean to determine DSI lane state during
-					horizontal back porch (HBP) blanking period.
-- qcom,mdss-dsi-hsa-power-mode:		Boolean to determine DSI lane state during
-					horizontal sync active (HSA) mode.
-- qcom,mdss-dsi-last-line-interleave	Boolean to determine if last line
-					interleave flag needs to be enabled.
-- qcom,mdss-dsi-bllp-eof-power-mode:	Boolean to determine DSI lane state during
-					blanking low power period (BLLP) EOF mode.
-- qcom,mdss-dsi-bllp-power-mode:	Boolean to determine DSI lane state during
-					blanking low power period (BLLP) mode.
-- qcom,mdss-dsi-traffic-mode:		Specifies the panel traffic mode.
-					"non_burst_sync_pulse" = non burst with sync pulses (default).
-					"non_burst_sync_event" = non burst with sync start event.
-					"burst_mode" = burst mode.
-- qcom,mdss-dsi-pixel-packing:		Specifies if pixel packing is used (in case of RGB666).
-					"tight" = Tight packing (default value).
-					"loose" = Loose packing.
-- qcom,mdss-dsi-virtual-channel-id:	Specifies the virtual channel identefier.
-					0 = default value.
-- qcom,mdss-dsi-color-order:		Specifies the R, G and B channel ordering.
-					"rgb_swap_rgb" = DSI_RGB_SWAP_RGB (default value)
-					"rgb_swap_rbg" = DSI_RGB_SWAP_RBG
-					"rgb_swap_brg" = DSI_RGB_SWAP_BRG
-					"rgb_swap_grb" = DSI_RGB_SWAP_GRB
-					"rgb_swap_gbr" = DSI_RGB_SWAP_GBR
-- qcom,mdss-dsi-lane-0-state:		Boolean that specifies whether data lane 0 is enabled.
-- qcom,mdss-dsi-lane-1-state:		Boolean that specifies whether data lane 1 is enabled.
-- qcom,mdss-dsi-lane-2-state:		Boolean that specifies whether data lane 2 is enabled.
-- qcom,mdss-dsi-lane-3-state:		Boolean that specifies whether data lane 3 is enabled.
-- qcom,mdss-dsi-t-clk-post:		Specifies the byte clock cycles after mode switch.
-					0x03 = default value.
-- qcom,mdss-dsi-t-clk-pre:		Specifies the byte clock cycles before mode switch.
-					0x24 = default value.
-- qcom,mdss-dsi-stream:			Specifies the packet stream to be used.
-					0 = stream 0 (default)
-					1 = stream 1
-- qcom,mdss-dsi-mdp-trigger:		Specifies the trigger mechanism to be used for MDP path.
-					"none" = no trigger
-					"trigger_te" = Tear check signal line used for trigger
-					"trigger_sw" = Triggered by software (default)
-					"trigger_sw_te" = Software trigger and TE
-- qcom,mdss-dsi-dma-trigger:		Specifies the trigger mechanism to be used for DMA path.
-					"none" = no trigger
-					"trigger_te" = Tear check signal line used for trigger
-					"trigger_sw" = Triggered by software (default)
-					"trigger_sw_seof" = Software trigger and start/end of frame trigger.
-					"trigger_sw_te" = Software trigger and TE
-- qcom,mdss-dsi-panel-framerate:	Specifies the frame rate for the panel.
-					60 = 60 frames per second (default)
-- qcom,mdss-dsi-panel-clockrate:	A 64 bit value specifies the panel clock speed in Hz.
-					0 = default value.
-- qcom,mdss-mdp-transfer-time-us:	Specifies the dsi transfer time for command mode
-					panels in microseconds. Driver uses this number to adjust
-					the clock rate according to the expected transfer time.
-					Increasing this value would slow down the mdp processing
-					and can result in slower performance.
-					Decreasing this value can speed up the mdp processing,
-					but this can also impact power consumption.
-					As a rule this time should not be higher than the time
-					that would be expected with the processing at the
-					dsi link rate since anyways this would be the maximum
-					transfer time that could be achieved.
-					If ping pong split enabled, this time should not be higher
-					than two times the dsi link rate time.
-					14000 = default value.
-- qcom,mdss-dsi-on-command-state:	String that specifies the ctrl state for sending ON commands.
-					"dsi_lp_mode" = DSI low power mode (default)
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-dsi-off-command-state:	String that specifies the ctrl state for sending OFF commands.
-					"dsi_lp_mode" = DSI low power mode (default)
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-dsi-post-mode-switch-on-command-state:	String that specifies the ctrl state for sending ON commands post mode switch.
-					"dsi_lp_mode" = DSI low power mode (default)
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-pan-physical-width-dimension:	Specifies panel physical width in mm which corresponds
-					to the physical width in the framebuffer information.
-- qcom,mdss-pan-physical-height-dimension:	Specifies panel physical height in mm which corresponds
-					to the physical height in the framebuffer information.
-- qcom,mdss-dsi-mode-sel-gpio-state:	String that specifies the lcd mode for panel
-					(such as single-port/dual-port), if qcom,panel-mode-gpio
-					binding is defined in dsi controller.
-					"dual_port" = Set GPIO to LOW
-					"single_port" = Set GPIO to HIGH
-					"high" = Set GPIO to HIGH
-					"low" = Set GPIO to LOW
-					The default value is "dual_port".
-- qcom,mdss-tear-check-disable:		Boolean to disable mdp tear check. Tear check is enabled by default to avoid
-					tearing. Other tear-check properties are ignored if this property is present.
-					The below tear check configuration properties can be individually tuned if
-					tear check is enabled.
-- qcom,mdss-tear-check-sync-cfg-height: Specifies the vertical total number of lines.
-					The default value is 0xfff0.
-- qcom,mdss-tear-check-sync-init-val:	Specifies the init value at which the read pointer gets loaded
-					at vsync edge. The reader pointer refers to the line number of
-					panel buffer that is currently being updated.
-					The default value is panel height.
-- qcom,mdss-tear-check-sync-threshold-start:
-					Allows the first ROI line write to an panel when read pointer is
-					between the range of ROI start line and ROI start line plus this
-					setting.
-					The default value is 4.
-- qcom,mdss-tear-check-sync-threshold-continue:
-					The minimum number of lines the write pointer needs to be
-					above the read pointer so that it is safe to write to the panel.
-					(This check is not done for the first ROI line write of an update)
-					The default value is 4.
-- qcom,mdss-tear-check-start-pos:	Specify the y position from which the start_threshold value is
-					added and write is kicked off if the read pointer falls within that
-					region.
-					The default value is panel height.
-- qcom,mdss-tear-check-rd-ptr-trigger-intr:
-					Specify the read pointer value at which an interrupt has to be
-					generated.
-					The default value is panel height + 1.
-- qcom,mdss-tear-check-frame-rate:	Specify the value to be a real frame rate(fps) x 100 factor to tune the
-					timing of TE simulation with more precision.
-					The default value is 6000 with 60 fps.
-- qcom,mdss-dsi-reset-sequence:		An array that lists the
-					sequence of reset gpio values and sleeps
-					Each command will have the format defined
-					as below:
-					--> Reset GPIO value
-					--> Sleep value (in ms)
-- qcom,partial-update-enabled:		String used to enable partial
-					panel update for command mode panels.
-					"none": partial update is disabled
-					"single_roi": default enable mode, only single roi is sent to panel
-					"dual_roi": two rois are merged into one big roi. Panel ddic should be able
-					to process two roi's along with the DCS command to send two rois.
-					disabled if property is not specified.
-- qcom,mdss-dsi-horizontal-line-idle:	List of width ranges (EC - SC) in pixels indicating
-					additional idle time in dsi clock cycles that is needed
-					to compensate for smaller line width.
-- qcom,partial-update-roi-merge:	Boolean indicates roi combination is need
-					and function has been provided for dcs
-					2A/2B command.
-- qcom,dcs-cmd-by-left:			Boolean to indicate that dcs command are sent
-					through the left DSI controller only in a dual-dsi configuration
-- qcom,mdss-dsi-panel-hdr-enabled:      Boolean to indicate HDR support in panel.
-- qcom,mdss-dsi-panel-hdr-color-primaries:
-                                        Array of 8 unsigned integers denoting chromaticity of panel.These
-                                        values are specified in nits units. The value range is 0 through 50000.
-                                        To obtain real chromacity, these values should be divided by factor of
-                                        50000. The structure of array is defined in below order
-                                        value 1: x value of white chromaticity of display panel
-                                        value 2: y value of white chromaticity of display panel
-                                        value 3: x value of red chromaticity of display panel
-                                        value 4: y value of red chromaticity of display panel
-                                        value 5: x value of green chromaticity of display panel
-                                        value 6: y value of green chromaticity of display panel
-                                        value 7: x value of blue chromaticity of display panel
-                                        value 8: y value of blue chromaticity of display panel
-- qcom,mdss-dsi-panel-peak-brightness:  Maximum brightness supported by panel.In absence of maximum value
-                                        typical value becomes peak brightness. Value is specified in nits units.
-                                        To obtain real peak brightness, this value should be divided by factor of
-                                        10000.
-- qcom,mdss-dsi-panel-blackness-level:  Blackness level supported by panel. Blackness level is defined as
-                                        ratio of peak brightness to contrast. Value is specified in nits units.
-                                        To obtain real blackness level, this value should be divided by factor of
-                                        10000.
-- qcom,mdss-dsi-lp11-init:		Boolean used to enable the DSI clocks and data lanes (low power 11)
-					before issuing hardware reset line.
-- qcom,mdss-dsi-init-delay-us:		Delay in microseconds(us) before performing any DSI activity in lp11
-					mode. This master delay (t_init_delay as per DSI spec) should be sum
-					of DSI internal delay to reach fuctional after power up and minimum
-					delay required by panel to reach functional.
-- qcom,mdss-dsi-rx-eot-ignore:		Boolean used to enable ignoring end of transmission packets.
-- qcom,mdss-dsi-tx-eot-append:		Boolean used to enable appending end of transmission packets.
-- qcom,ulps-enabled:			Boolean to enable support for Ultra Low Power State (ULPS) mode.
-- qcom,suspend-ulps-enabled:		Boolean to enable support for ULPS mode for panels during suspend state.
-- qcom,panel-roi-alignment:		Specifies the panel ROI alignment restrictions on its
-					left, top, width, height alignments and minimum width and
-					height values
-- qcom,esd-check-enabled:		Boolean used to enable ESD recovery feature.
-- qcom,mdss-dsi-panel-status-command:	A byte stream formed by multiple dcs packets based on
-					qcom dsi controller protocol, to read the panel status.
-					This value is used to kick in the ESD recovery.
-					byte 0: dcs data type
-					byte 1: set to indicate this is an individual packet
-						 (no chain)
-					byte 2: virtual channel number
-					byte 3: expect ack from client (dcs read command)
-					byte 4: wait number of specified ms after dcs command
-						 transmitted
-					byte 5, 6: 16 bits length in network byte order
-					byte 7 and beyond: number byte of payload
-- qcom,mdss-dsi-panel-status-command-mode:
-					String that specifies the ctrl state for reading the panel status.
-					"dsi_lp_mode" = DSI low power mode
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-dsi-lp1-command:		An optional byte stream to request low
-					power mode on a panel
-- qcom,mdss-dsi-lp1-command-mode:	String that specifies the ctrl state for
-					setting the panel power mode.
-					"dsi_lp_mode" = DSI low power mode
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-dsi-lp2-command:		An optional byte stream to request ultra
-					low power mode on a panel
-- qcom,mdss-dsi-lp2-command-mode:	String that specifies the ctrl state for
-					setting the panel power mode.
-					"dsi_lp_mode" = DSI low power mode
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-dsi-nolp-command:		An optional byte stream to disable low
-					power and ultra low power panel modes
-- qcom,mdss-dsi-nolp-command-mode:	String that specifies the ctrl state for
-					setting the panel power mode.
-					"dsi_lp_mode" = DSI low power mode
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-dsi-panel-status-check-mode:Specifies the panel status check method for ESD recovery.
-					"bta_check" = Uses BTA to check the panel status
-					"reg_read" = Reads panel status register to check the panel status
-					"reg_read_nt35596" = Reads panel status register to check the panel
-							     status for NT35596 panel.
-					"te_signal_check" = Uses TE signal behaviour to check the panel status
-- qcom,mdss-dsi-panel-status-read-length: Integer array that specify the expected read-back length of values
-					  for each of panel registers. Each length is corresponding to number of
-					  returned parameters of register introduced in specification.
-- qcom,mdss-dsi-panel-status-valid-params: Integer array that specify the valid returned values which need to check
-					   for each of register.
-					   Some panel need only check the first few values returned from panel.
-					   So: if this property is the same to qcom,mdss-dsi-panel-status-read-length,
-					   then just ignore this one.
-- qcom,mdss-dsi-panel-status-value:	Multiple integer arrays, each specifies the values of the panel status register
-					which is used to check the panel status. The size of each array is the sum of
-					length specified in qcom,mdss-dsi-panel-status-read-length, and must be equal.
-					This can cover that Some panel may return several alternative values.
-- qcom,mdss-dsi-panel-max-error-count:  Integer value that specifies the maximum number of errors from register
-					read that can be ignored before treating that the panel has gone bad.
-- qcom,dynamic-mode-switch-enabled:		Boolean used to mention whether panel supports
-					dynamic switching from video mode to command mode
-					and vice versa.
-- qcom,dynamic-mode-switch-type:		A string specifies how to perform dynamic mode switch.
-						If qcom,dynamic-mode-switch-enabled is set and no string specified, default value is
-						dynamic-switch-suspend-resume.
-					"dynamic-switch-suspend-resume"= Switch using suspend/resume. Panel will
-						go blank during transition.
-					"dynamic-switch-immediate"= Switch on next frame update. Panel will
-						not go blank for this transition.
-					"dynamic-resolution-switch-immediate"= Switch the panel resolution. Panel will
-						not go blank for this transition.
-- qcom,mdss-dsi-post-mode-switch-on-command:		Multiple dcs packets used for turning on DSI panel
-					after panel has switch modes.
-					Refer to "qcom,mdss-dsi-on-command" section for adding commands.
-- qcom,video-to-cmd-mode-switch-commands:	List of commands that need to be sent
-					to panel in order to switch from video mode to command mode dynamically.
-					Refer to "qcom,mdss-dsi-on-command" section for adding commands.
-- qcom,cmd-to-video-mode-switch-commands:	List of commands that need to be sent
-					to panel in order to switch from command mode to video mode dynamically.
-					Refer to "qcom,mdss-dsi-on-command" section for adding commands.
-- qcom,send-pps-before-switch:		Boolean propety to indicate when PPS commands should be sent,
-					either before or after switch commands during dynamic resolution
-					switch in DSC panels. If the property is not present, the default
-					behavior is to send PPS commands after the switch commands.
-- qcom,mdss-dsi-panel-orientation:	String used to indicate orientation of panel
-					"180" = panel is flipped in both horizontal and vertical directions
-					"hflip" = panel is flipped in horizontal direction
-					"vflip" = panel is flipped in vertical direction
-- qcom,panel-ack-disabled: A boolean property to indicate, whether we need to wait for any ACK from the panel
-			   for any commands that we send.
-- qcom,mdss-dsi-force-clock-lane-hs:	Boolean to force dsi clock lanes to HS mode always.
-
-- qcom,compression-mode:		Select compression mode for panel.
-					"fbc" - frame buffer compression
-					"dsc" - display stream compression.
-					If "dsc" compression is used then config subnodes needs to be defined.
-- qcom,panel-supply-entries:		A node that lists the elements of the supply used to
-					power the DSI panel. There can be more than one instance
-					of this binding, in which case the entry would be appended
-					with the supply entry index. For a detailed description of
-					fields in the supply entry, refer to the qcom,ctrl-supply-entries
-					binding above.
-- qcom,mdss-dsc-version:		An 8 bit value indicates the DSC version supported by panel. Bits[0.3]
-					provides information about minor version while Bits[4.7] provides
-					major version information. It supports only DSC rev 1(Major).1(Minor)
-					right now.
-- qcom,mdss-dsc-scr-version:		Each DSC version can have multiple SCR. This 8 bit value indicates
-					current SCR revision information supported by panel.
-- qcom,mdss-dsc-encoders:		An integer value indicating how many DSC encoders should be used
-					to drive data stream to DSI.
-					Default value is 1 and max value is 2.
-					2 encoder should be used only if qcom,mdss-lm-split or
-					qcom,split-mode with pingpong-split is used.
-- qcom,mdss-dsc-slice-height:		An integer value indicates the dsc slice height.
-- qcom,mdss-dsc-slice-width:		An integer value indicates the dsc slice width.
-					Multiple of slice width should be equal to panel-width.
-					Maximum 2 slices per DSC encoder can be used so if 2 DSC encoders
-					are used then minimum slice width is equal to panel-width/4.
-- qcom,mdss-dsc-slice-per-pkt:		An integer value indicates the slice per dsi packet.
-- qcom,mdss-dsc-bit-per-component: 	An integer value indicates the bits per component before compression.
-- qcom,mdss-dsc-bit-per-pixel:		An integer value indicates the bits per pixel after compression.
-- qcom,mdss-dsc-block-prediction-enable: A boolean value to enable/disable the block prediction at decoder.
-- qcom,mdss-dsc-config-by-manufacture-cmd: A boolean to indicates panel use manufacture command to setup pps
-					instead of standard dcs type 0x0A.
-- qcom,display-topology:  		Array of u32 values which specifies the	list of topologies available
-					for the display. A display topology is defined by a
-					set of 3 values in the order:
-					- number of mixers
-					- number of compression encoders
-					- number of interfaces
-					Therefore, the array should always contain a tuple of 3 elements.
-- qcom,default-topology-index:          An u32 value which indexes the topology set
-					specified by the node "qcom,display-topology"
-					to identify the default topology for the
-					display. The first set is indexed by the
-					value 0.
-
-Required properties for sub-nodes:	None
-Optional properties:
-- qcom,dba-panel:	Indicates whether the current panel is used as a display bridge
-					to a non-DSI interface.
-- qcom,bridge-name:			A string to indicate the name of the bridge chip connected to DSI. qcom,bridge-name
-					is required if qcom,dba-panel is defined for the panel.
-- qcom,adjust-timer-wakeup-ms:		An integer value to indicate the timer delay(in ms) to accommodate
-					s/w delay while configuring the event timer wakeup logic.
-
-- qcom,mdss-dsi-display-timings:	Parent node that lists the different resolutions that the panel supports.
-					Each child represents timings settings for a specific resolution.
-- qcom,mdss-dsi-post-init-delay:        Specifies required number of frames to wait so that panel can be functional
-					to show proper display.
-
-Additional properties added to the second level nodes that represent timings properties:
-- qcom,mdss-dsi-timing-default:		Property that specifies the current child as the default
-					timing configuration that will be used.
-- qcom,mdss-dsi-timing-switch-command:	List of commands that need to be sent
-					to panel when the resolution/timing switch happens dynamically.
-					Refer to "qcom,mdss-dsi-on-command" section for adding commands.
-- qcom,mdss-dsi-timing-switch-command-state:	String that specifies the ctrl state for sending resolution switch
-					commands.
-					"dsi_lp_mode" = DSI low power mode (default)
-					"dsi_hs_mode" = DSI high speed mode
-
-Note, if a given optional qcom,* binding is not present, then the driver will configure
-the default values specified.
-
-Example:
-&mdss_mdp {
-	dsi_sim_vid: qcom,mdss_dsi_sim_video {
-		qcom,mdss-dsi-panel-name = "simulator video mode dsi panel";
-		qcom,mdss-dsi-panel-controller = <&mdss_dsi0>;
-		qcom,mdss-dsi-panel-height = <1280>;
-		qcom,mdss-dsi-panel-width = <720>;
-		qcom,mdss-dsi-bpp = <24>;
-		qcom,mdss-dsi-pixel-packing = <0>;
-		qcom,mdss-dsi-panel-destination = "display_1";
-		qcom,cmd-sync-wait-broadcast;
-		qcom,mdss-dsi-fbc-enable;
-		qcom,mdss-dsi-fbc-slice-height = <5>;
-		qcom,mdss-dsi-fbc-2d-pred-mode;
-		qcom,mdss-dsi-fbc-ver2-mode;
-		qcom,mdss-dsi-fbc-bpp = <0>;
-		qcom,mdss-dsi-fbc-packing = <0>;
-		qcom,mdss-dsi-fbc-quant-error;
-		qcom,mdss-dsi-fbc-bias = <0>;
-		qcom,mdss-dsi-fbc-pat-mode;
-		qcom,mdss-dsi-fbc-vlc-mode;
-		qcom,mdss-dsi-fbc-bflc-mode;
-		qcom,mdss-dsi-fbc-h-line-budget = <0>;
-		qcom,mdss-dsi-fbc-budget-ctrl = <0>;
-		qcom,mdss-dsi-fbc-block-budget = <0>;
-		qcom,mdss-dsi-fbc-lossless-threshold = <0>;
-		qcom,mdss-dsi-fbc-lossy-threshold = <0>;
-		qcom,mdss-dsi-fbc-rgb-threshold = <0>;
-		qcom,mdss-dsi-fbc-lossy-mode-idx = <0>;
-		qcom,mdss-dsi-fbc-max-pred-err = <2>;
-		qcom,mdss-dsi-h-front-porch = <140>;
-		qcom,mdss-dsi-h-back-porch = <164>;
-		qcom,mdss-dsi-h-pulse-width = <8>;
-		qcom,mdss-dsi-h-sync-skew = <0>;
-		qcom,mdss-dsi-v-back-porch = <6>;
-		qcom,mdss-dsi-v-front-porch = <1>;
-		qcom,mdss-dsi-v-pulse-width = <1>;
-		qcom,mdss-dsi-h-left-border = <0>;
-		qcom,mdss-dsi-h-right-border = <0>;
-		qcom,mdss-dsi-v-top-border = <0>;
-		qcom,mdss-dsi-v-bottom-border = <0>;
-		qcom,mdss-dsi-border-color = <0>;
-		qcom,mdss-dsi-underflow-color = <0xff>;
-		qcom,mdss-dsi-bl-min-level = <1>;
-		qcom,mdss-dsi-bl-max-level = < 15>;
-		qcom,mdss-brightness-max-level = <255>;
-		qcom,mdss-dsi-interleave-mode = <0>;
-		qcom,mdss-dsi-panel-type = "dsi_video_mode";
-		qcom,mdss-dsi-te-check-enable;
-		qcom,mdss-dsi-te-using-wd;
-		qcom,mdss-dsi-te-using-te-pin;
-		qcom,mdss-dsi-te-dcs-command = <1>;
-		qcom,mdss-dsi-wr-mem-continue = <0x3c>;
-		qcom,mdss-dsi-wr-mem-start = <0x2c>;
-		qcom,mdss-dsi-te-pin-select = <1>;
-		qcom,mdss-dsi-h-sync-pulse = <1>;
-		qcom,mdss-dsi-hfp-power-mode;
-		qcom,mdss-dsi-hbp-power-mode;
-		qcom,mdss-dsi-hsa-power-mode;
-		qcom,mdss-dsi-bllp-eof-power-mode;
-		qcom,mdss-dsi-bllp-power-mode;
-		qcom,mdss-dsi-last-line-interleave;
-		qcom,mdss-dsi-traffic-mode = <0>;
-		qcom,mdss-dsi-virtual-channel-id = <0>;
-		qcom,mdss-dsi-color-order = <0>;
-		qcom,mdss-dsi-lane-0-state;
-		qcom,mdss-dsi-lane-1-state;
-		qcom,mdss-dsi-lane-2-state;
-		qcom,mdss-dsi-lane-3-state;
-		qcom,mdss-dsi-t-clk-post = <0x20>;
-		qcom,mdss-dsi-t-clk-pre = <0x2c>;
-		qcom,mdss-dsi-stream = <0>;
-		qcom,mdss-dsi-mdp-trigger = <0>;
-		qcom,mdss-dsi-dma-trigger = <0>;
-		qcom,mdss-dsi-panel-framerate = <60>;
-		qcom,mdss-dsi-panel-clockrate = <424000000>;
-		qcom,mdss-mdp-transfer-time-us = <12500>;
-		qcom,mdss-dsi-panel-timings = [7d 25 1d 00 37 33
-					22 27 1e 03 04 00];
-                qcom,mdss-dsi-panel-timings-8996 = [23 20 06 09 05 03 04 a0
-                                23 20 06 09 05 03 04 a0
-                                23 20 06 09 05 03 04 a0
-                                23 20 06 09 05 03 04 a0
-                                23 2e 06 08 05 03 04 a0];
-		qcom,mdss-dsi-on-command = [32 01 00 00 00 00 02 00 00
-					29 01 00 00 10 00 02 FF 99];
-		qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
-		qcom,mdss-dsi-off-command = [22 01 00 00 00 00 00];
-		qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
-		qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
-		qcom,mdss-dsi-pan-enable-dynamic-fps;
-		qcom,mdss-dsi-pan-fps-update = "dfps_suspend_resume_mode";
-		qcom,min-refresh-rate = <30>;
-		qcom,max-refresh-rate = <60>;
-		qcom,mdss-dsi-bl-pmic-bank-select = <0>;
-		qcom,mdss-dsi-bl-pmic-pwm-frequency = <0>;
-		qcom,mdss-dsi-pwm-gpio = <&pm8941_mpps 5 0>;
-		qcom,5v-boost-gpio = <&pm8994_gpios 14 0>;
-		qcom,mdss-pan-physical-width-dimension = <60>;
-		qcom,mdss-pan-physical-height-dimension = <140>;
-		qcom,mdss-dsi-mode-sel-gpio-state = "dsc_mode";
-		qcom,mdss-tear-check-sync-cfg-height = <0xfff0>;
-		qcom,mdss-tear-check-sync-init-val = <1280>;
-		qcom,mdss-tear-check-sync-threshold-start = <4>;
-		qcom,mdss-tear-check-sync-threshold-continue = <4>;
-		qcom,mdss-tear-check-start-pos = <1280>;
-		qcom,mdss-tear-check-rd-ptr-trigger-intr = <1281>;
-		qcom,mdss-tear-check-frame-rate = <6000>;
-		qcom,mdss-dsi-reset-sequence = <1 2>, <0 10>, <1 10>;
-		qcom,partial-update-enabled = "single_roi";
-		qcom,dcs-cmd-by-left;
-		qcom,mdss-dsi-lp11-init;
-		qcom,mdss-dsi-init-delay-us = <100>;
-		mdss-dsi-rx-eot-ignore;
-		mdss-dsi-tx-eot-append;
-		qcom,ulps-enabled;
-		qcom,suspend-ulps-enabled;
-		qcom,panel-roi-alignment = <4 4 2 2 20 20>;
-		qcom,esd-check-enabled;
-		qcom,mdss-dsi-panel-status-command = [06 01 00 01 05 00 02 0A 08];
-		qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode";
-		qcom,mdss-dsi-panel-status-check-mode = "reg_read";
-		qcom,mdss-dsi-panel-status-read-length = <8>;
-		qcom,mdss-dsi-panel-max-error-count = <3>;
-		qcom,mdss-dsi-panel-status-value = <0x1c 0x00 0x05 0x02 0x40 0x84 0x06 0x01>;
-		qcom,dynamic-mode-switch-enabled;
-		qcom,dynamic-mode-switch-type = "dynamic-switch-immediate";
-		qcom,mdss-dsi-post-mode-switch-on-command = [32 01 00 00 00 00 02 00 00
-					29 01 00 00 10 00 02 B0 03];
-		qcom,video-to-cmd-mode-switch-commands = [15 01 00 00 00 00 02 C2 0B
-						15 01 00 00 00 00 02 C2 08];
-		qcom,cmd-to-video-mode-switch-commands = [15 01 00 00 00 00 02 C2 03];
-		qcom,send-pps-before-switch;
-		qcom,panel-ack-disabled;
-		qcom,mdss-dsi-horizontal-line-idle = <0 40 256>,
-						<40 120 128>,
-						<128 240 64>;
-		qcom,mdss-dsi-panel-orientation = "180"
-		qcom,mdss-dsi-panel-jitter = <0x8 0x10>;
-		qcom,mdss-dsi-panel-prefill-lines = <0x10>;
-		qcom,mdss-dsi-force-clock-lane-hs;
-		qcom,compression-mode = "dsc";
-		qcom,adjust-timer-wakeup-ms = <1>;
-		qcom,mdss-dsi-display-timings {
-			wqhd {
-				qcom,mdss-dsi-timing-default;
-				qcom,mdss-dsi-panel-width = <720>;
-				qcom,mdss-dsi-panel-height = <2560>;
-				qcom,mdss-dsi-h-front-porch = <20>;
-				qcom,mdss-dsi-h-back-porch = <8>;
-				qcom,mdss-dsi-h-pulse-width = <8>;
-				qcom,mdss-dsi-h-sync-skew = <0>;
-				qcom,mdss-dsi-v-back-porch = <4>;
-				qcom,mdss-dsi-v-front-porch = <728>;
-				qcom,mdss-dsi-v-pulse-width = <4>;
-				qcom,mdss-dsi-panel-framerate = <60>;
-				qcom,mdss-dsi-panel-timings = [E6 38 26 00 68 6E 2A 3C 2C 03 04 00];
-				qcom,mdss-dsi-t-clk-post = <0x02>;
-				qcom,mdss-dsi-t-clk-pre = <0x2a>;
-				qcom,mdss-dsi-on-command = [05 01 00 00 a0 00 02 11 00
-					05 01 00 00 02 00 02 29 00];
-				qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
-				qcom,mdss-dsi-timing-switch-command = [
-					29 00 00 00 00 00 02 B0 04
-					29 00 00 00 00 00 02 F1 00];
-				qcom,mdss-dsi-timing-switch-command-state = "dsi_lp_mode";
-
-				qcom,mdss-dsc-slice-height = <16>;
-				qcom,mdss-dsc-slice-width = <360>;
-				qcom,mdss-dsc-slice-per-pkt = <2>;
-				qcom,mdss-dsc-bit-per-component = <8>;
-				qcom,mdss-dsc-bit-per-pixel = <8>;
-				qcom,mdss-dsc-block-prediction-enable;
-				qcom,mdss-dsc-config-by-manufacture-cmd;
-				qcom,display-topology = <1 1 1>;
-				qcom,default-topology-index = <0>;
-			};
-		};
-		qcom,panel-supply-entries {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			qcom,panel-supply-entry@0 {
-				reg = <0>;
-				qcom,supply-name = "vdd";
-				qcom,supply-min-voltage = <2800000>;
-				qcom,supply-max-voltage = <2800000>;
-				qcom,supply-enable-load = <100000>;
-				qcom,supply-disable-load = <100>;
-				qcom,supply-pre-on-sleep = <0>;
-				qcom,supply-post-on-sleep = <0>;
-				qcom,supply-pre-off-sleep = <0>;
-				qcom,supply-post-off-sleep = <0>;
-			};
-
-			qcom,panel-supply-entry@1 {
-				reg = <1>;
-				qcom,supply-name = "vddio";
-				qcom,supply-min-voltage = <1800000>;
-				qcom,supply-max-voltage = <1800000>;
-				qcom,supply-enable-load = <100000>;
-				qcom,supply-disable-load = <100>;
-				qcom,supply-pre-on-sleep = <0>;
-				qcom,supply-post-on-sleep = <0>;
-				qcom,supply-pre-off-sleep = <0>;
-				qcom,supply-post-off-sleep = <0>;
-			};
-		};
-
-		qcom,dba-panel;
-		qcom,bridge-name = "adv7533";
-		qcom,mdss-dsc-version = <0x11>;
-		qcom,mdss-dsc-scr-version = <0x1>;
-		qcom,mdss-dsc-slice-height = <16>;
-		qcom,mdss-dsc-slice-width = <360>;
-		qcom,mdss-dsc-slice-per-pkt = <2>;
-		qcom,mdss-dsc-bit-per-component = <8>;
-		qcom,mdss-dsc-bit-per-pixel = <8>;
-		qcom,mdss-dsc-block-prediction-enable;
-		qcom,mdss-dsc-config-by-manufacture-cmd;
-		qcom,display-topology = <1 1 1>,
-			                <2 2 1>;
-		qcom,default-topology-index = <0>;
-	};
-};
diff --git a/Documentation/devicetree/bindings/fb/mdss-dsi-panel.txt b/Documentation/devicetree/bindings/fb/mdss-dsi-panel.txt
deleted file mode 100644
index 608b426..0000000
--- a/Documentation/devicetree/bindings/fb/mdss-dsi-panel.txt
+++ /dev/null
@@ -1,742 +0,0 @@
-Qualcomm mdss-dsi-panel
-
-mdss-dsi-panel is a dsi panel device which supports panels that
-are compatible with MIPI display serial interface specification.
-
-Required properties:
-- compatible:				This property applies to DSI V2 panels only.
-					This property should not be added for panels
-					that work based on version "V6.0"
-					DSI panels that are of different versions
-					are initialized by the drivers for dsi controller.
-					This property specifies the version
-					for DSI HW that this panel will work with
-					"qcom,dsi-panel-v2" = DSI V2.0
-- status:        			This property applies to DSI V2 panels only.
-					This property should not be added for panels
-					that work based on version "V6.0"
-					DSI panels that are of different versions
-					are initialized by the drivers for dsi controller.
-					A string that has to be set to "okay/ok"
-					to enable the panel driver. By default this property
-					will be set to "disable". Will be set to "ok/okay"
-					status for specific platforms.
-- qcom,mdss-dsi-panel-controller:	Specifies the phandle for the DSI controller that
-					this panel will be mapped to.
-- qcom,mdss-dsi-panel-width:		Specifies panel width in pixels.
-- qcom,mdss-dsi-panel-height:		Specifies panel height in pixels.
-- qcom,mdss-dsi-bpp:			Specifies the panel bits per pixel.
-					3  = for rgb111
-					8  = for rgb332
-					12 = for rgb444
-					16 = for rgb565
-					18 = for rgb666
-					24 = for rgb888
-- qcom,mdss-dsi-panel-destination:	A string that specifies the destination display for the panel.
-					"display_1" = DISPLAY_1
-					"display_2" = DISPLAY_2
-- qcom,mdss-dsi-panel-timings:		An array of length 12 that specifies the PHY
-					timing settings for the panel.
-- qcom,mdss-dsi-panel-timings-8996:		An array of length 40 char that specifies the 8996 PHY lane
-					timing settings for the panel.
-- qcom,mdss-dsi-on-command:		A byte stream formed by multiple dcs packets base on
-					qcom dsi controller protocol.
-					byte 0: dcs data type
-					byte 1: set to indicate this is an individual packet
-						 (no chain)
-					byte 2: virtual channel number
-					byte 3: expect ack from client (dcs read command)
-					byte 4: wait number of specified ms after dcs command
-						 transmitted
-					byte 5, 6: 16 bits length in network byte order
-					byte 7 and beyond: number byte of payload
-- qcom,mdss-dsi-off-command:		A byte stream formed by multiple dcs packets base on
-					qcom dsi controller protocol.
-					byte 0: dcs data type
-					byte 1: set to indicate this is an individual packet
-						 (no chain)
-					byte 2: virtual channel number
-					byte 3: expect ack from client (dcs read command)
-					byte 4: wait number of specified ms after dcs command
-						 transmitted
-					byte 5, 6: 16 bits length in network byte order
-					byte 7 and beyond: number byte of payload
-- qcom,mdss-dsi-post-panel-on-command:	same as "qcom,mdss-dsi-on-command" except commands are
-					sent after displaying an image.
-
-Note, if a short DCS packet(i.e packet with Byte 0:dcs data type as 05) mentioned in
-qcom,mdss-dsi-on-command/qcom,mdss-dsi-off-command stream fails to transmit,
-then 3 options can be tried.
-	1. Send the packet as a long packet instead
-				Byte 0: dcs data type = 05 (DCS short Packet)
-				Byte 0: dcs data type = 29 (DCS long Packet)
-	2. Send the packet in one burst by prepending with the next packet in packet stream
-				Byte 1 = 01 (indicates this is an individual packet)
-				Byte 1 = 00 (indicates this will be appended to the next
-					     individual packet in the packet stream)
-	3. Prepend a NULL packet to the short packet and send both in one burst instead of
-	   combining multiple short packets and sending them in one burst.
-
-Optional properties:
-- qcom,mdss-dsi-panel-name:		A string used as a descriptive name of the panel
-- qcom,cmd-sync-wait-broadcast:		Boolean used to broadcast dcs command to panels.
-- qcom,mdss-dsi-fbc-enable:		Boolean used to enable frame buffer compression mode.
-- qcom,mdss-dsi-fbc-slice-height:	Slice height(in lines) of compressed block.
-					Expressed as power of 2. To set as 128 lines,
-					this should be set to 7.
-- qcom,mdss-dsi-fbc-2d-pred-mode:	Boolean to enable 2D map prediction.
-- qcom,mdss-dsi-fbc-ver2-mode:		Boolean to enable FBC 2.0 that supports 1/3
-					compression.
-- qcom,mdss-dsi-fbc-bpp:		Compressed bpp supported by the panel.
-					Specified color order is used as default value.
-- qcom,mdss-dsi-fbc-packing:		Component packing.
-					0 = default value.
-- qcom,mdss-dsi-fbc-quant-error:	Boolean used to enable quantization error calculation.
-- qcom,mdss-dsi-fbc-bias:		Bias for CD.
-					0 = default value.
-- qcom,mdss-dsi-fbc-pat-mode:		Boolean used to enable PAT mode.
-- qcom,mdss-dsi-fbc-vlc-mode:		Boolean used to enable VLC mode.
-- qcom,mdss-dsi-fbc-bflc-mode:		Boolean used to enable BFLC mode.
-- qcom,mdss-dsi-fbc-h-line-budget:	Per line extra budget.
-					0 = default value.
-- qcom,mdss-dsi-fbc-budget-ctrl:		Extra budget level.
-					0 = default value.
-- qcom,mdss-dsi-fbc-block-budget:		Per block budget.
-					0 = default value.
-- qcom,mdss-dsi-fbc-lossless-threshold: Lossless mode threshold.
-					0 = default value.
-- qcom,mdss-dsi-fbc-lossy-threshold:	Lossy mode threshold.
-					0 = default value.
-- qcom,mdss-dsi-fbc-rgb-threshold:	Lossy RGB threshold.
-					0 = default value.
-- qcom,mdss-dsi-fbc-lossy-mode-idx:	Lossy mode index value.
-					0 = default value.
-- qcom,mdss-dsi-fbc-max-pred-err:	Max quantization prediction error.
-					0 = default value
-- qcom,mdss-dsi-h-back-porch:		Horizontal back porch value in pixel.
-					6 = default value.
-- qcom,mdss-dsi-h-front-porch:		Horizontal front porch value in pixel.
-					6 = default value.
-- qcom,mdss-dsi-h-pulse-width:		Horizontal pulse width.
-					2 = default value.
-- qcom,mdss-dsi-h-sync-skew:		Horizontal sync skew value.
-					0 = default value.
-- qcom,mdss-dsi-v-back-porch:		Vertical back porch value in pixel.
-					6 = default value.
-- qcom,mdss-dsi-v-front-porch:		Vertical front porch value in pixel.
-					6 = default value.
-- qcom,mdss-dsi-v-pulse-width:		Vertical pulse width.
-					2 = default value.
-- qcom,mdss-dsi-h-left-border:		Horizontal left border in pixel.
-					0 = default value
-- qcom,mdss-dsi-h-right-border:		Horizontal right border in pixel.
-					0 = default value
-- qcom,mdss-dsi-v-top-border:		Vertical top border in pixel.
-					0 = default value
-- qcom,mdss-dsi-v-bottom-border:	Vertical bottom border in pixel.
-					0 = default value
-- qcom,mdss-dsi-underflow-color:	Specifies the controller settings for the
-					panel under flow color.
-					0xff = default value.
-- qcom,mdss-dsi-border-color:		Defines the border color value if border is present.
-					0 = default value.
-- qcom,mdss-dsi-pan-enable-dynamic-fps:	Boolean used to enable change in frame rate dynamically.
-- qcom,mdss-dsi-pan-fps-update:		A string that specifies when to change the frame rate.
-					"dfps_suspend_resume_mode"= FPS change request is
-					implemented during suspend/resume.
-					"dfps_immediate_clk_mode" = FPS change request is
-					implemented immediately using DSI clocks.
-					"dfps_immediate_porch_mode_hfp" = FPS change request is
-					implemented immediately by changing panel horizontal
-					front porch values.
-					"dfps_immediate_porch_mode_vfp" = FPS change request is
-					implemented immediately by changing panel vertical
-					front porch values.
-- qcom,min-refresh-rate:		Minimum refresh rate supported by the panel.
-- qcom,max-refresh-rate:		Maximum refresh rate supported by the panel. If max refresh
-					rate is not specified, then the frame rate of the panel in
-					qcom,mdss-dsi-panel-framerate is used.
-- qcom,mdss-dsi-bl-pmic-control-type:	A string that specifies the implementation of backlight
-					control for this panel.
-					"bl_ctrl_pwm" = Backlight controlled by PWM gpio.
-					"bl_ctrl_wled" = Backlight controlled by WLED.
-					"bl_ctrl_dcs" = Backlight controlled by DCS commands.
-					other: Unknown backlight control. (default)
-- qcom,mdss-dsi-bl-pwm-pmi:		Boolean to indicate that PWM control is through second pmic chip.
-- qcom,mdss-dsi-bl-pmic-bank-select:	LPG channel for backlight.
-					Required if blpmiccontroltype is PWM
-- qcom,mdss-dsi-bl-pmic-pwm-frequency:	PWM period in microseconds.
-					Required if blpmiccontroltype is PWM
-- qcom,mdss-dsi-pwm-gpio:		PMIC gpio binding to backlight.
-					Required if blpmiccontroltype is PWM
-- qcom,mdss-dsi-bl-min-level:		Specifies the min backlight level supported by the panel.
-					0 = default value.
-- qcom,mdss-dsi-bl-max-level:		Specifies the max backlight level supported by the panel.
-					255 = default value.
-- qcom,mdss-brightness-max-level:	Specifies the max brightness level supported.
-					255 = default value.
-- qcom,mdss-dsi-interleave-mode:	Specifies interleave mode.
-					0 = default value.
-- qcom,mdss-dsi-panel-type:		Specifies the panel operating mode.
-					"dsi_video_mode" = enable video mode (default).
-					"dsi_cmd_mode" = enable command mode.
-- qcom,5v-boost-gpio:			Specifies the panel gpio for display 5v boost.
-- qcom,mdss-dsi-te-check-enable:	Boolean to enable Tear Check configuration.
-- qcom,mdss-dsi-te-using-te-pin:	Boolean to specify whether using hardware vsync.
-- qcom,mdss-dsi-te-pin-select:		Specifies TE operating mode.
-					0 = TE through embedded dcs command
-					1 = TE through TE gpio pin. (default)
-- qcom,mdss-dsi-te-dcs-command:		Inserts the dcs command.
-					1 = default value.
-- qcom,mdss-dsi-wr-mem-start:		DCS command for write_memory_start.
-					0x2c = default value.
-- qcom,mdss-dsi-wr-mem-continue:	DCS command for write_memory_continue.
-					0x3c = default value.
-- qcom,mdss-dsi-h-sync-pulse:		Specifies the pulse mode option for the panel.
-					0 = Don't send hsa/he following vs/ve packet(default)
-					1 = Send hsa/he following vs/ve packet
-- qcom,mdss-dsi-hfp-power-mode:		Boolean to determine DSI lane state during
-					horizontal front porch (HFP) blanking period.
-- qcom,mdss-dsi-hbp-power-mode:		Boolean to determine DSI lane state during
-					horizontal back porch (HBP) blanking period.
-- qcom,mdss-dsi-hsa-power-mode:		Boolean to determine DSI lane state during
-					horizontal sync active (HSA) mode.
-- qcom,mdss-dsi-last-line-interleave	Boolean to determine if last line
-					interleave flag needs to be enabled.
-- qcom,mdss-dsi-bllp-eof-power-mode:	Boolean to determine DSI lane state during
-					blanking low power period (BLLP) EOF mode.
-- qcom,mdss-dsi-bllp-power-mode:	Boolean to determine DSI lane state during
-					blanking low power period (BLLP) mode.
-- qcom,mdss-dsi-traffic-mode:		Specifies the panel traffic mode.
-					"non_burst_sync_pulse" = non burst with sync pulses (default).
-					"non_burst_sync_event" = non burst with sync start event.
-					"burst_mode" = burst mode.
-- qcom,mdss-dsi-pixel-packing:		Specifies if pixel packing is used (in case of RGB666).
-					"tight" = Tight packing (default value).
-					"loose" = Loose packing.
-- qcom,mdss-dsi-virtual-channel-id:	Specifies the virtual channel identefier.
-					0 = default value.
-- qcom,mdss-dsi-color-order:		Specifies the R, G and B channel ordering.
-					"rgb_swap_rgb" = DSI_RGB_SWAP_RGB (default value)
-					"rgb_swap_rbg" = DSI_RGB_SWAP_RBG
-					"rgb_swap_brg" = DSI_RGB_SWAP_BRG
-					"rgb_swap_grb" = DSI_RGB_SWAP_GRB
-					"rgb_swap_gbr" = DSI_RGB_SWAP_GBR
-- qcom,mdss-dsi-lane-0-state:		Boolean that specifies whether data lane 0 is enabled.
-- qcom,mdss-dsi-lane-1-state:		Boolean that specifies whether data lane 1 is enabled.
-- qcom,mdss-dsi-lane-2-state:		Boolean that specifies whether data lane 2 is enabled.
-- qcom,mdss-dsi-lane-3-state:		Boolean that specifies whether data lane 3 is enabled.
-- qcom,mdss-dsi-t-clk-post:		Specifies the byte clock cycles after mode switch.
-					0x03 = default value.
-- qcom,mdss-dsi-t-clk-pre:		Specifies the byte clock cycles before mode switch.
-					0x24 = default value.
-- qcom,mdss-dsi-stream:			Specifies the packet stream to be used.
-					0 = stream 0 (default)
-					1 = stream 1
-- qcom,mdss-dsi-mdp-trigger:		Specifies the trigger mechanism to be used for MDP path.
-					"none" = no trigger
-					"trigger_te" = Tear check signal line used for trigger
-					"trigger_sw" = Triggered by software (default)
-					"trigger_sw_te" = Software trigger and TE
-- qcom,mdss-dsi-dma-trigger:		Specifies the trigger mechanism to be used for DMA path.
-					"none" = no trigger
-					"trigger_te" = Tear check signal line used for trigger
-					"trigger_sw" = Triggered by software (default)
-					"trigger_sw_seof" = Software trigger and start/end of frame trigger.
-					"trigger_sw_te" = Software trigger and TE
-- qcom,mdss-dsi-panel-framerate:	Specifies the frame rate for the panel.
-					60 = 60 frames per second (default)
-- qcom,mdss-dsi-panel-clockrate:	A 64 bit value specifies the panel clock speed in Hz.
-					0 = default value.
-- qcom,mdss-mdp-transfer-time-us:	Specifies the dsi transfer time for command mode
-					panels in microseconds. Driver uses this number to adjust
-					the clock rate according to the expected transfer time.
-					Increasing this value would slow down the mdp processing
-					and can result in slower performance.
-					Decreasing this value can speed up the mdp processing,
-					but this can also impact power consumption.
-					As a rule this time should not be higher than the time
-					that would be expected with the processing at the
-					dsi link rate since anyways this would be the maximum
-					transfer time that could be achieved.
-					If ping pong split enabled, this time should not be higher
-					than two times the dsi link rate time.
-					14000 = default value.
-- qcom,mdss-dsi-on-command-state:	String that specifies the ctrl state for sending ON commands.
-					"dsi_lp_mode" = DSI low power mode (default)
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-dsi-off-command-state:	String that specifies the ctrl state for sending OFF commands.
-					"dsi_lp_mode" = DSI low power mode (default)
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-dsi-post-mode-switch-on-command-state:	String that specifies the ctrl state for sending ON commands post mode switch.
-					"dsi_lp_mode" = DSI low power mode (default)
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-pan-physical-width-dimension:	Specifies panel physical width in mm which corresponds
-					to the physical width in the framebuffer information.
-- qcom,mdss-pan-physical-height-dimension:	Specifies panel physical height in mm which corresponds
-					to the physical height in the framebuffer information.
-- qcom,mdss-dsi-mode-sel-gpio-state:	String that specifies the lcd mode for panel
-					(such as single-port/dual-port), if qcom,panel-mode-gpio
-					binding is defined in dsi controller.
-					"dual_port" = Set GPIO to LOW
-					"single_port" = Set GPIO to HIGH
-					"high" = Set GPIO to HIGH
-					"low" = Set GPIO to LOW
-					The default value is "dual_port".
-- qcom,mdss-tear-check-disable:		Boolean to disable mdp tear check. Tear check is enabled by default to avoid
-					tearing. Other tear-check properties are ignored if this property is present.
-					The below tear check configuration properties can be individually tuned if
-					tear check is enabled.
-- qcom,mdss-tear-check-sync-cfg-height: Specifies the vertical total number of lines.
-					The default value is 0xfff0.
-- qcom,mdss-tear-check-sync-init-val:	Specifies the init value at which the read pointer gets loaded
-					at vsync edge. The reader pointer refers to the line number of
-					panel buffer that is currently being updated.
-					The default value is panel height.
-- qcom,mdss-tear-check-sync-threshold-start:
-					Allows the first ROI line write to an panel when read pointer is
-					between the range of ROI start line and ROI start line plus this
-					setting.
-					The default value is 4.
-- qcom,mdss-tear-check-sync-threshold-continue:
-					The minimum number of lines the write pointer needs to be
-					above the read pointer so that it is safe to write to the panel.
-					(This check is not done for the first ROI line write of an update)
-					The default value is 4.
-- qcom,mdss-tear-check-start-pos:	Specify the y position from which the start_threshold value is
-					added and write is kicked off if the read pointer falls within that
-					region.
-					The default value is panel height.
-- qcom,mdss-tear-check-rd-ptr-trigger-intr:
-					Specify the read pointer value at which an interrupt has to be
-					generated.
-					The default value is panel height + 1.
-- qcom,mdss-tear-check-frame-rate:	Specify the value to be a real frame rate(fps) x 100 factor to tune the
-					timing of TE simulation with more precision.
-					The default value is 6000 with 60 fps.
-- qcom,mdss-dsi-reset-sequence:		An array that lists the
-					sequence of reset gpio values and sleeps
-					Each command will have the format defined
-					as below:
-					--> Reset GPIO value
-					--> Sleep value (in ms)
-- qcom,partial-update-enabled:		Boolean used to enable partial
-					panel update for command mode panels.
-- qcom,mdss-dsi-horizontal-line-idle:	List of width ranges (EC - SC) in pixels indicating
-					additional idle time in dsi clock cycles that is needed
-					to compensate for smaller line width.
-- qcom,partial-update-roi-merge:	Boolean indicates roi combination is need
-					and function has been provided for dcs
-					2A/2B command.
-- qcom,dcs-cmd-by-left:			Boolean to indicate that dcs command are sent
-					through the left DSI controller only in a dual-dsi configuration
-- qcom,mdss-dsi-lp11-init:		Boolean used to enable the DSI clocks and data lanes (low power 11)
-					before issuing hardware reset line.
-- qcom,mdss-dsi-init-delay-us:		Delay in microseconds(us) before performing any DSI activity in lp11
-					mode. This master delay (t_init_delay as per DSI spec) should be sum
-					of DSI internal delay to reach fuctional after power up and minimum
-					delay required by panel to reach functional.
-- qcom,mdss-dsi-rx-eot-ignore:		Boolean used to enable ignoring end of transmission packets.
-- qcom,mdss-dsi-tx-eot-append:		Boolean used to enable appending end of transmission packets.
-- qcom,ulps-enabled:			Boolean to enable support for Ultra Low Power State (ULPS) mode.
-- qcom,suspend-ulps-enabled:		Boolean to enable support for ULPS mode for panels during suspend state.
-- qcom,panel-roi-alignment:		Specifies the panel ROI alignment restrictions on its
-					left, top, width, height alignments and minimum width and
-					height values
-- qcom,esd-check-enabled:		Boolean used to enable ESD recovery feature.
-- qcom,mdss-dsi-panel-status-command:	A byte stream formed by multiple dcs packets based on
-					qcom dsi controller protocol, to read the panel status.
-					This value is used to kick in the ESD recovery.
-					byte 0: dcs data type
-					byte 1: set to indicate this is an individual packet
-						 (no chain)
-					byte 2: virtual channel number
-					byte 3: expect ack from client (dcs read command)
-					byte 4: wait number of specified ms after dcs command
-						 transmitted
-					byte 5, 6: 16 bits length in network byte order
-					byte 7 and beyond: number byte of payload
-- qcom,mdss-dsi-panel-status-command-mode:
-					String that specifies the ctrl state for reading the panel status.
-					"dsi_lp_mode" = DSI low power mode
-					"dsi_hs_mode" = DSI high speed mode
-- qcom,mdss-dsi-panel-status-check-mode:Specifies the panel status check method for ESD recovery.
-					"bta_check" = Uses BTA to check the panel status
-					"reg_read" = Reads panel status register to check the panel status
-					"reg_read_nt35596" = Reads panel status register to check the panel
-							     status for NT35596 panel.
-					"te_signal_check" = Uses TE signal behaviour to check the panel status
-- qcom,mdss-dsi-panel-status-read-length: Integer array that specify the expected read-back length of values
-					  for each of panel registers. Each length is corresponding to number of
-					  returned parameters of register introduced in specification.
-- qcom,mdss-dsi-panel-status-valid-params: Integer array that specify the valid returned values which need to check
-					   for each of register.
-					   Some panel need only check the first few values returned from panel.
-					   So: if this property is the same to qcom,mdss-dsi-panel-status-read-length,
-					   then just ignore this one.
-- qcom,mdss-dsi-panel-status-value:	Multiple integer arrays, each specifies the values of the panel status register
-					which is used to check the panel status. The size of each array is the sum of
-					length specified in qcom,mdss-dsi-panel-status-read-length, and must be equal.
-					This can cover that Some panel may return several alternative values.
-- qcom,mdss-dsi-panel-max-error-count:  Integer value that specifies the maximum number of errors from register
-					read that can be ignored before treating that the panel has gone bad.
-- qcom,dynamic-mode-switch-enabled:		Boolean used to mention whether panel supports
-					dynamic switching from video mode to command mode
-					and vice versa.
-- qcom,dynamic-mode-switch-type:		A string specifies how to perform dynamic mode switch.
-						If qcom,dynamic-mode-switch-enabled is set and no string specified, default value is
-						dynamic-switch-suspend-resume.
-					"dynamic-switch-suspend-resume"= Switch using suspend/resume. Panel will
-						go blank during transition.
-					"dynamic-switch-immediate"= Switch on next frame update. Panel will
-						not go blank for this transition.
-					"dynamic-resolution-switch-immediate"= Switch the panel resolution. Panel will
-						not go blank for this transition.
-- qcom,mdss-dsi-post-mode-switch-on-command:		Multiple dcs packets used for turning on DSI panel
-					after panel has switch modes.
-					Refer to "qcom,mdss-dsi-on-command" section for adding commands.
-- qcom,video-to-cmd-mode-switch-commands:	List of commands that need to be sent
-					to panel in order to switch from video mode to command mode dynamically.
-					Refer to "qcom,mdss-dsi-on-command" section for adding commands.
-- qcom,cmd-to-video-mode-switch-commands:	List of commands that need to be sent
-					to panel in order to switch from command mode to video mode dynamically.
-					Refer to "qcom,mdss-dsi-on-command" section for adding commands.
-- qcom,send-pps-before-switch:		Boolean propety to indicate when PPS commands should be sent,
-					either before or after switch commands during dynamic resolution
-					switch in DSC panels. If the property is not present, the default
-					behavior is to send PPS commands after the switch commands.
-- qcom,mdss-dsi-panel-orientation:	String used to indicate orientation of panel
-					"180" = panel is flipped in both horizontal and vertical directions
-					"hflip" = panel is flipped in horizontal direction
-					"vflip" = panel is flipped in vertical direction
-- qcom,panel-ack-disabled: A boolean property to indicate, whether we need to wait for any ACK from the panel
-			   for any commands that we send.
-- qcom,mdss-dsi-force-clock-lane-hs:	Boolean to force dsi clock lanes to HS mode always.
-
-- qcom,compression-mode:		Select compression mode for panel.
-					"fbc" - frame buffer compression
-					"dsc" - display stream compression.
-					If "dsc" compression is used then config subnodes needs to be defined.
-- qcom,panel-supply-entries:		A node that lists the elements of the supply used to
-					power the DSI panel. There can be more than one instance
-					of this binding, in which case the entry would be appended
-					with the supply entry index. For a detailed description of
-					fields in the supply entry, refer to the qcom,ctrl-supply-entries
-					binding above.
-- qcom,config-select:			Optional property to select default configuration.
-
-[[Optional config sub-nodes]]		These subnodes provide different configurations for a given same panel.
-					Default configuration can be chosen by specifying phandle of the
-					selected subnode in the qcom,config-select.
-Required properties for sub-nodes:	None
-Optional properites:
-- qcom,lm-split:			An array of two values indicating MDP should use two layer
-					mixers to reduce power.
-					Ex: Normally 1080x1920 display uses single DSI and thus one layer
-					    mixer. But if we use two layer mixers then mux the output of
-					    those two mixers into single stream and route it to single DSI
-					    then we can lower the clock requirements of MDP. To use this
-					    configuration we need two fill this array with <540 540>.
-					Both values doesn't have to be same, but recommended, however sum of
-					both values has to be equal to the panel-width.
-					By default two mixer streams are merged using 2D mux, however if
-					2 DSC encoders are used then merge is performed within compression
-					engine.
-- qcom,split-mode:			String property indicating which split mode MDP should use. Valid
-					entries are "pingpong-split" and "dualctl-split".
-					This property is mutually exclusive with qcom,lm-split.
-- qcom,mdss-dsc-version:		An 8 bit value indicates the DSC version supported by panel. Bits[0.3]
-					provides information about minor version while Bits[4.7] provides
-					major version information. It supports only DSC rev 1(Major).1(Minor)
-					right now.
-- qcom,mdss-dsc-scr-version:		Each DSC version can have multiple SCR. This 8 bit value indicates
-					current SCR revision information supported by panel.
-- qcom,mdss-dsc-encoders:		An integer value indicating how many DSC encoders should be used
-					to drive data stream to DSI.
-					Default value is 1 and max value is 2.
-					2 encoder should be used only if qcom,mdss-lm-split or
-					qcom,split-mode with pingpong-split is used.
-- qcom,mdss-dsc-slice-height:		An integer value indicates the dsc slice height.
-- qcom,mdss-dsc-slice-width:		An integer value indicates the dsc slice width.
-					Multiple of slice width should be equal to panel-width.
-					Maximum 2 slices per DSC encoder can be used so if 2 DSC encoders
-					are used then minimum slice width is equal to panel-width/4.
-- qcom,mdss-dsc-slice-per-pkt:		An integer value indicates the slice per dsi packet.
-- qcom,mdss-dsc-bit-per-component: 	An integer value indicates the bits per component before compression.
-- qcom,mdss-dsc-bit-per-pixel:		An integer value indicates the bits per pixel after compression.
-- qcom,mdss-dsc-block-prediction-enable: A boolean value to enable/disable the block prediction at decoder.
-- qcom,mdss-dsc-config-by-manufacture-cmd: A boolean to indicates panel use manufacture command to setup pps
-					instead of standard dcs type 0x0A.
-- qcom,dba-panel:	Indicates whether the current panel is used as a display bridge
-					to a non-DSI interface.
-- qcom,bridge-name:			A string to indicate the name of the bridge chip connected to DSI. qcom,bridge-name
-					is required if qcom,dba-panel is defined for the panel.
-- qcom,adjust-timer-wakeup-ms:		An integer value to indicate the timer delay(in ms) to accommodate
-					s/w delay while configuring the event timer wakeup logic.
-
-- qcom,mdss-dsi-display-timings:	Parent node that lists the different resolutions that the panel supports.
-					Each child represents timings settings for a specific resolution.
-- qcom,mdss-dsi-post-init-delay:        Specifies required number of frames to wait so that panel can be functional
-					to show proper display.
-
-Additional properties added to the second level nodes that represent timings properties:
-- qcom,mdss-dsi-timing-default:		Property that specifies the current child as the default
-					timing configuration that will be used.
-- qcom,mdss-dsi-timing-switch-command:	List of commands that need to be sent
-					to panel when the resolution/timing switch happens dynamically.
-					Refer to "qcom,mdss-dsi-on-command" section for adding commands.
-- qcom,mdss-dsi-timing-switch-command-state:	String that specifies the ctrl state for sending resolution switch
-					commands.
-					"dsi_lp_mode" = DSI low power mode (default)
-					"dsi_hs_mode" = DSI high speed mode
-
-Note, if a given optional qcom,* binding is not present, then the driver will configure
-the default values specified.
-
-Example:
-&mdss_mdp {
-	dsi_sim_vid: qcom,mdss_dsi_sim_video {
-		qcom,mdss-dsi-panel-name = "simulator video mode dsi panel";
-		qcom,mdss-dsi-panel-controller = <&mdss_dsi0>;
-		qcom,mdss-dsi-panel-height = <1280>;
-		qcom,mdss-dsi-panel-width = <720>;
-		qcom,mdss-dsi-bpp = <24>;
-		qcom,mdss-dsi-pixel-packing = <0>;
-		qcom,mdss-dsi-panel-destination = "display_1";
-		qcom,cmd-sync-wait-broadcast;
-		qcom,mdss-dsi-fbc-enable;
-		qcom,mdss-dsi-fbc-slice-height = <5>;
-		qcom,mdss-dsi-fbc-2d-pred-mode;
-		qcom,mdss-dsi-fbc-ver2-mode;
-		qcom,mdss-dsi-fbc-bpp = <0>;
-		qcom,mdss-dsi-fbc-packing = <0>;
-		qcom,mdss-dsi-fbc-quant-error;
-		qcom,mdss-dsi-fbc-bias = <0>;
-		qcom,mdss-dsi-fbc-pat-mode;
-		qcom,mdss-dsi-fbc-vlc-mode;
-		qcom,mdss-dsi-fbc-bflc-mode;
-		qcom,mdss-dsi-fbc-h-line-budget = <0>;
-		qcom,mdss-dsi-fbc-budget-ctrl = <0>;
-		qcom,mdss-dsi-fbc-block-budget = <0>;
-		qcom,mdss-dsi-fbc-lossless-threshold = <0>;
-		qcom,mdss-dsi-fbc-lossy-threshold = <0>;
-		qcom,mdss-dsi-fbc-rgb-threshold = <0>;
-		qcom,mdss-dsi-fbc-lossy-mode-idx = <0>;
-		qcom,mdss-dsi-fbc-max-pred-err = <2>;
-		qcom,mdss-dsi-h-front-porch = <140>;
-		qcom,mdss-dsi-h-back-porch = <164>;
-		qcom,mdss-dsi-h-pulse-width = <8>;
-		qcom,mdss-dsi-h-sync-skew = <0>;
-		qcom,mdss-dsi-v-back-porch = <6>;
-		qcom,mdss-dsi-v-front-porch = <1>;
-		qcom,mdss-dsi-v-pulse-width = <1>;
-		qcom,mdss-dsi-h-left-border = <0>;
-		qcom,mdss-dsi-h-right-border = <0>;
-		qcom,mdss-dsi-v-top-border = <0>;
-		qcom,mdss-dsi-v-bottom-border = <0>;
-		qcom,mdss-dsi-border-color = <0>;
-		qcom,mdss-dsi-underflow-color = <0xff>;
-		qcom,mdss-dsi-bl-min-level = <1>;
-		qcom,mdss-dsi-bl-max-level = < 15>;
-		qcom,mdss-brightness-max-level = <255>;
-		qcom,mdss-dsi-interleave-mode = <0>;
-		qcom,mdss-dsi-panel-type = "dsi_video_mode";
-		qcom,mdss-dsi-te-check-enable;
-		qcom,mdss-dsi-te-using-te-pin;
-		qcom,mdss-dsi-te-dcs-command = <1>;
-		qcom,mdss-dsi-wr-mem-continue = <0x3c>;
-		qcom,mdss-dsi-wr-mem-start = <0x2c>;
-		qcom,mdss-dsi-te-pin-select = <1>;
-		qcom,mdss-dsi-h-sync-pulse = <1>;
-		qcom,mdss-dsi-hfp-power-mode;
-		qcom,mdss-dsi-hbp-power-mode;
-		qcom,mdss-dsi-hsa-power-mode;
-		qcom,mdss-dsi-bllp-eof-power-mode;
-		qcom,mdss-dsi-bllp-power-mode;
-		qcom,mdss-dsi-last-line-interleave;
-		qcom,mdss-dsi-traffic-mode = <0>;
-		qcom,mdss-dsi-virtual-channel-id = <0>;
-		qcom,mdss-dsi-color-order = <0>;
-		qcom,mdss-dsi-lane-0-state;
-		qcom,mdss-dsi-lane-1-state;
-		qcom,mdss-dsi-lane-2-state;
-		qcom,mdss-dsi-lane-3-state;
-		qcom,mdss-dsi-t-clk-post = <0x20>;
-		qcom,mdss-dsi-t-clk-pre = <0x2c>;
-		qcom,mdss-dsi-stream = <0>;
-		qcom,mdss-dsi-mdp-trigger = <0>;
-		qcom,mdss-dsi-dma-trigger = <0>;
-		qcom,mdss-dsi-panel-framerate = <60>;
-		qcom,mdss-dsi-panel-clockrate = <424000000>;
-		qcom,mdss-mdp-transfer-time-us = <12500>;
-		qcom,mdss-dsi-panel-timings = [7d 25 1d 00 37 33
-					22 27 1e 03 04 00];
-                qcom,mdss-dsi-panel-timings-8996 = [23 20 06 09 05 03 04 a0
-                                23 20 06 09 05 03 04 a0
-                                23 20 06 09 05 03 04 a0
-                                23 20 06 09 05 03 04 a0
-                                23 2e 06 08 05 03 04 a0];
-		qcom,mdss-dsi-on-command = [32 01 00 00 00 00 02 00 00
-					29 01 00 00 10 00 02 FF 99];
-		qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
-		qcom,mdss-dsi-off-command = [22 01 00 00 00 00 00];
-		qcom,mdss-dsi-off-command-state = "dsi_hs_mode";
-		qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_wled";
-		qcom,mdss-dsi-pan-enable-dynamic-fps;
-		qcom,mdss-dsi-pan-fps-update = "dfps_suspend_resume_mode";
-		qcom,min-refresh-rate = <30>;
-		qcom,max-refresh-rate = <60>;
-		qcom,mdss-dsi-bl-pmic-bank-select = <0>;
-		qcom,mdss-dsi-bl-pmic-pwm-frequency = <0>;
-		qcom,mdss-dsi-pwm-gpio = <&pm8941_mpps 5 0>;
-		qcom,5v-boost-gpio = <&pm8994_gpios 14 0>;
-		qcom,mdss-pan-physical-width-dimension = <60>;
-		qcom,mdss-pan-physical-height-dimension = <140>;
-		qcom,mdss-dsi-mode-sel-gpio-state = "dsc_mode";
-		qcom,mdss-tear-check-sync-cfg-height = <0xfff0>;
-		qcom,mdss-tear-check-sync-init-val = <1280>;
-		qcom,mdss-tear-check-sync-threshold-start = <4>;
-		qcom,mdss-tear-check-sync-threshold-continue = <4>;
-		qcom,mdss-tear-check-start-pos = <1280>;
-		qcom,mdss-tear-check-rd-ptr-trigger-intr = <1281>;
-		qcom,mdss-tear-check-frame-rate = <6000>;
-		qcom,mdss-dsi-reset-sequence = <1 2>, <0 10>, <1 10>;
-		qcom,partial-update-enabled;
-		qcom,dcs-cmd-by-left;
-		qcom,mdss-dsi-lp11-init;
-		qcom,mdss-dsi-init-delay-us = <100>;
-		mdss-dsi-rx-eot-ignore;
-		mdss-dsi-tx-eot-append;
-		qcom,ulps-enabled;
-		qcom,suspend-ulps-enabled;
-		qcom,panel-roi-alignment = <4 4 2 2 20 20>;
-		qcom,esd-check-enabled;
-		qcom,mdss-dsi-panel-status-command = [06 01 00 01 05 00 02 0A 08];
-		qcom,mdss-dsi-panel-status-command-state = "dsi_lp_mode";
-		qcom,mdss-dsi-panel-status-check-mode = "reg_read";
-		qcom,mdss-dsi-panel-status-read-length = <8>;
-		qcom,mdss-dsi-panel-max-error-count = <3>;
-		qcom,mdss-dsi-panel-status-value = <0x1c 0x00 0x05 0x02 0x40 0x84 0x06 0x01>;
-		qcom,dynamic-mode-switch-enabled;
-		qcom,dynamic-mode-switch-type = "dynamic-switch-immediate";
-		qcom,mdss-dsi-post-mode-switch-on-command = [32 01 00 00 00 00 02 00 00
-					29 01 00 00 10 00 02 B0 03];
-		qcom,video-to-cmd-mode-switch-commands = [15 01 00 00 00 00 02 C2 0B
-						15 01 00 00 00 00 02 C2 08];
-		qcom,cmd-to-video-mode-switch-commands = [15 01 00 00 00 00 02 C2 03];
-		qcom,send-pps-before-switch;
-		qcom,panel-ack-disabled;
-		qcom,mdss-dsi-horizontal-line-idle = <0 40 256>,
-						<40 120 128>,
-						<128 240 64>;
-		qcom,mdss-dsi-panel-orientation = "180"
-		qcom,mdss-dsi-force-clock-lane-hs;
-		qcom,compression-mode = "dsc";
-		qcom,adjust-timer-wakeup-ms = <1>;
-		qcom,mdss-dsi-display-timings {
-			wqhd {
-				qcom,mdss-dsi-timing-default;
-				qcom,mdss-dsi-panel-width = <720>;
-				qcom,mdss-dsi-panel-height = <2560>;
-				qcom,mdss-dsi-h-front-porch = <20>;
-				qcom,mdss-dsi-h-back-porch = <8>;
-				qcom,mdss-dsi-h-pulse-width = <8>;
-				qcom,mdss-dsi-h-sync-skew = <0>;
-				qcom,mdss-dsi-v-back-porch = <4>;
-				qcom,mdss-dsi-v-front-porch = <728>;
-				qcom,mdss-dsi-v-pulse-width = <4>;
-				qcom,mdss-dsi-panel-framerate = <60>;
-				qcom,mdss-dsi-panel-timings = [E6 38 26 00 68 6E 2A 3C 2C 03 04 00];
-				qcom,mdss-dsi-t-clk-post = <0x02>;
-				qcom,mdss-dsi-t-clk-pre = <0x2a>;
-				qcom,mdss-dsi-on-command = [05 01 00 00 a0 00 02 11 00
-					05 01 00 00 02 00 02 29 00];
-				qcom,mdss-dsi-on-command-state = "dsi_lp_mode";
-				qcom,mdss-dsi-timing-switch-command = [
-					29 00 00 00 00 00 02 B0 04
-					29 00 00 00 00 00 02 F1 00];
-				qcom,mdss-dsi-timing-switch-command-state = "dsi_lp_mode";
-
-				qcom,config-select = <&dsi_sim_vid_config0>;
-				dsi_sim_vid_config0: config0 {
-					qcom,lm-split = <360 360>;
-					qcom,mdss-dsc-encoders = <2>;
-					qcom,mdss-dsc-slice-height = <16>;
-					qcom,mdss-dsc-slice-width = <360>;
-					qcom,mdss-dsc-slice-per-pkt = <2>;
-					qcom,mdss-dsc-bit-per-component = <8>;
-					qcom,mdss-dsc-bit-per-pixel = <8>;
-					qcom,mdss-dsc-block-prediction-enable;
-					qcom,mdss-dsc-config-by-manufacture-cmd;
-				};
-			};
-		};
-		qcom,panel-supply-entries {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			qcom,panel-supply-entry@0 {
-				reg = <0>;
-				qcom,supply-name = "vdd";
-				qcom,supply-min-voltage = <2800000>;
-				qcom,supply-max-voltage = <2800000>;
-				qcom,supply-enable-load = <100000>;
-				qcom,supply-disable-load = <100>;
-				qcom,supply-pre-on-sleep = <0>;
-				qcom,supply-post-on-sleep = <0>;
-				qcom,supply-pre-off-sleep = <0>;
-				qcom,supply-post-off-sleep = <0>;
-			};
-
-			qcom,panel-supply-entry@1 {
-				reg = <1>;
-				qcom,supply-name = "vddio";
-				qcom,supply-min-voltage = <1800000>;
-				qcom,supply-max-voltage = <1800000>;
-				qcom,supply-enable-load = <100000>;
-				qcom,supply-disable-load = <100>;
-				qcom,supply-pre-on-sleep = <0>;
-				qcom,supply-post-on-sleep = <0>;
-				qcom,supply-pre-off-sleep = <0>;
-				qcom,supply-post-off-sleep = <0>;
-			};
-		};
-
-		qcom,config-select = <&dsi_sim_vid_config0>;
-		qcom,dba-panel;
-		qcom,bridge-name = "adv7533";
-		qcom,mdss-dsc-version = <0x11>;
-		qcom,mdss-dsc-scr-version = <0x1>;
-
-		dsi_sim_vid_config0: config0 {
-			qcom,lm-split = <360 360>;
-			qcom,mdss-dsc-encoders = <2>;
-			qcom,mdss-dsc-slice-height = <16>;
-			qcom,mdss-dsc-slice-width = <360>;
-			qcom,mdss-dsc-slice-per-pkt = <2>;
-			qcom,mdss-dsc-bit-per-component = <8>;
-			qcom,mdss-dsc-bit-per-pixel = <8>;
-			qcom,mdss-dsc-block-prediction-enable;
-			qcom,mdss-dsc-config-by-manufacture-cmd;
-		};
-
-		dsi_sim_vid_config1: config1 {
-			qcom,mdss-dsc-encoders = <1>;
-			qcom,mdss-dsc-slice-height = <16>;
-			qcom,mdss-dsc-slice-width = <360>;
-			qcom,mdss-dsc-slice-per-pkt = <2>;
-			qcom,mdss-dsc-bit-per-component = <8>;
-			qcom,mdss-dsc-bit-per-pixel = <8>;
-			qcom,mdss-dsc-block-prediction-enable;
-			qcom,mdss-dsc-config-by-manufacture-cmd;
-		};
-
-		dsi_sim_vid_config2: config2 {
-			qcom,split-mode = "dualctl-split";
-		};
-
-		dsi_sim_vid_config3: config3 {
-			qcom,split-mode = "pingpong-split";
-		};
-	};
-};
diff --git a/Documentation/devicetree/bindings/fb/mdss-pll.txt b/Documentation/devicetree/bindings/fb/mdss-pll.txt
deleted file mode 100644
index 59fa6a0..0000000
--- a/Documentation/devicetree/bindings/fb/mdss-pll.txt
+++ /dev/null
@@ -1,103 +0,0 @@
-Qualcomm Technologies MDSS pll for DSI/EDP/HDMI
-
-mdss-pll is a pll controller device which supports pll devices that
-are compatible with MIPI display serial interface specification,
-HDMI and edp.
-
-Required properties:
-- compatible:		Compatible name used in the driver
-                        "qcom,mdss_dsi_pll_8916", "qcom,mdss_dsi_pll_8939",
-                        "qcom,mdss_dsi_pll_8974", "qcom,mdss_dsi_pll_8994",
-                        "qcom,mdss_dsi_pll_8994", "qcom,mdss_dsi_pll_8909",
-                        "qcom,mdss_hdmi_pll", "qcom,mdss_hdmi_pll_8994",
-                        "qcom,mdss_dsi_pll_8992", "qcom,mdss_hdmi_pll_8992",
-                        "qcom,mdss_dsi_pll_8996", "qcom,mdss_hdmi_pll_8996",
-                        "qcom,mdss_hdmi_pll_8996_v2", "qcom,mdss_dsi_pll_8996_v2",
-                        "qcom,mdss_hdmi_pll_8996_v3", "qcom,mdss_hdmi_pll_8996_v3_1p8",
-                        "qcom,mdss_edp_pll_8996_v3", "qcom,mdss_edp_pll_8996_v3_1p8",
-                        "qcom,mdss_dsi_pll_10nm", "qcom,mdss_dp_pll_8998",
-                        "qcom,mdss_hdmi_pll_8998", "qcom,mdss_dp_pll_10nm".
-- cell-index:		Specifies the controller used
-- reg:			offset and length of the register set for the device.
-- reg-names :		names to refer to register sets related to this device
-- gdsc-supply:		Phandle for gdsc regulator device node.
-- vddio-supply:		Phandle for vddio regulator device node.
-- clocks:		List of Phandles for clock device nodes
-			needed by the device.
-- clock-names:		List of clock names needed by the device.
-- clock-rate:		List of clock rates in Hz.
-
-Optional properties:
-- label:	       	A string used to describe the driver used.
-- vcca-supply:		Phandle for vcca regulator device node.
-
-
-- qcom,dsi-pll-ssc-en:	Boolean property to indicate that ssc is enabled.
-- qcom,dsi-pll-ssc-mode: Spread-spectrum clocking. It can be either "down-spread"
-			or "center-spread". Default is "down-spread" if it is not specified.
-- qcom,ssc-frequency-hz:	Integer property to specify the spread frequency
-			to be programmed for the SSC.
-- qcom,ssc-ppm:		Integer property to specify the Parts per Million
-			value of SSC.
-
-- qcom,platform-supply-entries:	A node that lists the elements of the supply. There
-				can be more than one instance of this binding,
-				in which case the entry would be appended with
-				the supply entry index.
-				e.g. qcom,platform-supply-entry@0
-				- reg: offset and length of the register set for the device.
-				-- qcom,supply-name: name of the supply (vdd/vdda/vddio)
-				-- qcom,supply-min-voltage: minimum voltage level (uV)
-				-- qcom,supply-max-voltage: maximum voltage level (uV)
-				-- qcom,supply-enable-load: load drawn (uA) from enabled supply
-				-- qcom,supply-disable-load: load drawn (uA) from disabled supply
-				-- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on
-				-- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
-				-- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
-				-- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
-
-Example:
-	mdss_dsi0_pll: qcom,mdss_dsi_pll@fd922A00 {
-		compatible = "qcom,mdss_dsi_pll_8974";
-		label = "MDSS DSI 0 PLL";
-		cell-index = <0>;
-
-		reg = <0xfd922A00 0xD4>,
-		      <0xfd922900 0x64>,
-		      <0xfd8c2300 0x8>;
-		reg-names = "pll_base", "dynamic_pll_base", "gdsc_base";
-		gdsc-supply = <&gdsc_mdss>;
-		vddio-supply = <&pm8941_l12>;
-		vcca-supply = <&pm8941_l28>;
-
-		clocks = <&clock_gcc clk_gcc_mdss_mdp_clk>,
-			 <&clock_gcc clk_gcc_mdss_ahb_clk>,
-			 <&clock_gcc clk_gcc_mdss_axi_clk>;
-		clock-names = "mdp_core_clk", "iface_clk", "bus_clk";
-		clock-rate = <0>, <0>, <0>;
-
-		qcom,dsi-pll-slave;
-		qcom,dsi-pll-ssc-en;
-		qcom,dsi-pll-ssc-mode = "down-spread";
-		qcom,ssc-frequency-hz = <30000>;
-		qcom,ssc-ppm = <5000>;
-
-		qcom,platform-supply-entries {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			qcom,platform-supply-entry@0 {
-				reg = <0>;
-				qcom,supply-name = "vddio";
-				qcom,supply-min-voltage = <1800000>;
-				qcom,supply-max-voltage = <1800000>;
-				qcom,supply-enable-load = <100000>;
-				qcom,supply-disable-load = <100>;
-				qcom,supply-pre-on-sleep = <0>;
-				qcom,supply-post-on-sleep = <20>;
-				qcom,supply-pre-off-sleep = <0>;
-				qcom,supply-post-off-sleep = <0>;
-			};
-		};
-	};
-
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
Freedreno mailing list
Freedreno@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/freedreno