From: satya priya <skakit@codeaurora.org>
To: Bjorn Andersson <bjorn.andersson@linaro.org>, gregkh@linuxfoundation.org
Cc: Andy Gross <agross@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Matthias Kaehlcke <mka@chromium.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, akashast@codeaurora.org,
rojay@codeaurora.org, msavaliy@qti.qualcomm.com,
satya priya <skakit@codeaurora.org>
Subject: [PATCH V2 1/3] arm64: dts: sc7180: Add wakeup support over UART RX
Date: Fri, 24 Jul 2020 09:28:00 +0530 [thread overview]
Message-ID: <1595563082-2353-2-git-send-email-skakit@codeaurora.org> (raw)
In-Reply-To: <1595563082-2353-1-git-send-email-skakit@codeaurora.org>
Add the necessary pinctrl and interrupts to make UART
wakeup capable.
Signed-off-by: satya priya <skakit@codeaurora.org>
---
Changes in V2:
- As per Matthias's comment added wakeup support for all the UARTs
of SC7180.
arch/arm64/boot/dts/qcom/sc7180.dtsi | 98 ++++++++++++++++++++++++++++++------
1 file changed, 84 insertions(+), 14 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 16df08d..044a4d0 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -787,9 +787,11 @@
reg = <0 0x00880000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&qup_uart0_default>;
- interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-1 = <&qup_uart0_sleep>;
+ interrupts-extended = <&intc GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 37 IRQ_TYPE_EDGE_FALLING>;
power-domains = <&rpmhpd SC7180_CX>;
operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
@@ -839,9 +841,11 @@
reg = <0 0x00884000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&qup_uart1_default>;
- interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-1 = <&qup_uart1_sleep>;
+ interrupts-extended = <&intc GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 3 IRQ_TYPE_EDGE_FALLING>;
power-domains = <&rpmhpd SC7180_CX>;
operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
@@ -925,9 +929,11 @@
reg = <0 0x0088c000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&qup_uart3_default>;
- interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-1 = <&qup_uart3_sleep>;
+ interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
power-domains = <&rpmhpd SC7180_CX>;
operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
@@ -1011,9 +1017,11 @@
reg = <0 0x00894000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&qup_uart5_default>;
- interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-1 = <&qup_uart5_sleep>;
+ interrupts-extended = <&intc GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 28 IRQ_TYPE_EDGE_FALLING>;
power-domains = <&rpmhpd SC7180_CX>;
operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_0 &qup_virt SLAVE_QUP_CORE_0>,
@@ -1078,9 +1086,11 @@
reg = <0 0x00a80000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&qup_uart6_default>;
- interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-1 = <&qup_uart6_sleep>;
+ interrupts-extended = <&intc GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 62 IRQ_TYPE_EDGE_FALLING>;
power-domains = <&rpmhpd SC7180_CX>;
operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
@@ -1250,9 +1260,11 @@
reg = <0 0x00a90000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&qup_uart10_default>;
- interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-1 = <&qup_uart10_sleep>;
+ interrupts-extended = <&intc GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 89 IRQ_TYPE_EDGE_FALLING>;
power-domains = <&rpmhpd SC7180_CX>;
operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
@@ -1302,9 +1314,11 @@
reg = <0 0x00a94000 0 0x4000>;
clock-names = "se";
clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
- pinctrl-names = "default";
+ pinctrl-names = "default", "sleep";
pinctrl-0 = <&qup_uart11_default>;
- interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-1 = <&qup_uart11_sleep>;
+ interrupts-extended = <&intc GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 56 IRQ_TYPE_EDGE_FALLING>;
power-domains = <&rpmhpd SC7180_CX>;
operating-points-v2 = <&qup_opp_table>;
interconnects = <&qup_virt MASTER_QUP_CORE_1 &qup_virt SLAVE_QUP_CORE_1>,
@@ -1632,6 +1646,14 @@
};
};
+ qup_uart0_sleep: qup-uart0-sleep {
+ pinmux {
+ pins = "gpio34", "gpio35",
+ "gpio36", "gpio37";
+ function = "gpio";
+ };
+ };
+
qup_uart1_default: qup-uart1-default {
pinmux {
pins = "gpio0", "gpio1",
@@ -1640,6 +1662,14 @@
};
};
+ qup_uart1_sleep: qup-uart1-sleep {
+ pinmux {
+ pins = "gpio0", "gpio1",
+ "gpio2", "gpio3";
+ function = "gpio";
+ };
+ };
+
qup_uart2_default: qup-uart2-default {
pinmux {
pins = "gpio15", "gpio16";
@@ -1655,6 +1685,14 @@
};
};
+ qup_uart3_sleep: qup-uart3-sleep {
+ pinmux {
+ pins = "gpio38", "gpio39",
+ "gpio40", "gpio41";
+ function = "gpio";
+ };
+ };
+
qup_uart4_default: qup-uart4-default {
pinmux {
pins = "gpio115", "gpio116";
@@ -1670,6 +1708,14 @@
};
};
+ qup_uart5_sleep: qup-uart5-sleep {
+ pinmux {
+ pins = "gpio25", "gpio26",
+ "gpio27", "gpio28";
+ function = "gpio";
+ };
+ };
+
qup_uart6_default: qup-uart6-default {
pinmux {
pins = "gpio59", "gpio60",
@@ -1678,6 +1724,14 @@
};
};
+ qup_uart6_sleep: qup-uart6-sleep {
+ pinmux {
+ pins = "gpio59", "gpio60",
+ "gpio61", "gpio62";
+ function = "gpio";
+ };
+ };
+
qup_uart7_default: qup-uart7-default {
pinmux {
pins = "gpio6", "gpio7";
@@ -1707,6 +1761,14 @@
};
};
+ qup_uart10_sleep: qup-uart10-sleep {
+ pinmux {
+ pins = "gpio86", "gpio87",
+ "gpio88", "gpio89";
+ function = "gpio";
+ };
+ };
+
qup_uart11_default: qup-uart11-default {
pinmux {
pins = "gpio53", "gpio54",
@@ -1715,6 +1777,14 @@
};
};
+ qup_uart11_sleep: qup-uart11-sleep {
+ pinmux {
+ pins = "gpio53", "gpio54",
+ "gpio55", "gpio56";
+ function = "gpio";
+ };
+ };
+
sdc1_on: sdc1-on {
pinconf-clk {
pins = "sdc1_clk";
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2020-07-24 3:58 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-07-24 3:57 [PATCH V2 0/3] Add wakeup support over UART RX satya priya
2020-07-24 3:58 ` satya priya [this message]
2020-07-28 5:36 ` [PATCH V2 1/3] arm64: dts: sc7180: " Akash Asthana
2020-07-24 3:58 ` [PATCH V2 2/3] arm64: dts: qcom: sc7180: Add sleep pin ctrl for BT uart satya priya
2020-07-28 5:38 ` Akash Asthana
2020-08-17 18:01 ` Matthias Kaehlcke
2020-08-17 23:33 ` Matthias Kaehlcke
2020-08-19 13:48 ` skakit
2020-08-19 13:49 ` skakit
2020-08-19 16:13 ` Matthias Kaehlcke
2020-08-20 12:19 ` skakit
2020-08-21 15:59 ` Matthias Kaehlcke
2020-07-24 3:58 ` [PATCH V2 3/3] tty: serial: qcom_geni_serial: Fix the UART wakeup issue satya priya
2020-07-24 8:42 ` Greg KH
2020-07-28 5:40 ` Akash Asthana
2020-08-17 17:42 ` Matthias Kaehlcke
2020-08-19 13:49 ` skakit
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1595563082-2353-2-git-send-email-skakit@codeaurora.org \
--to=skakit@codeaurora.org \
--cc=agross@kernel.org \
--cc=akashast@codeaurora.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mka@chromium.org \
--cc=msavaliy@qti.qualcomm.com \
--cc=robh+dt@kernel.org \
--cc=rojay@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.