From: <gregkh@linuxfoundation.org>
To: tobiasdiedrich@gmail.com, gregkh@linuxfoundation.org,
stable@vger.kernel.org
Subject: patch "serial: 8250_pci: Add Realtek 816a and 816b" added to tty-linus
Date: Wed, 16 Sep 2020 13:23:59 +0200 [thread overview]
Message-ID: <160025543941103@kroah.com> (raw)
This is a note to let you know that I've just added the patch titled
serial: 8250_pci: Add Realtek 816a and 816b
to my tty git tree which can be found at
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty.git
in the tty-linus branch.
The patch will show up in the next release of the linux-next tree
(usually sometime within the next 24 hours during the week.)
The patch will hopefully also be merged in Linus's tree for the
next -rc kernel release.
If you have any questions about this process, please let me know.
From 3c5a87be170aba8ac40982182f812dcff6ed1ad1 Mon Sep 17 00:00:00 2001
From: Tobias Diedrich <tobiasdiedrich@gmail.com>
Date: Mon, 14 Sep 2020 19:36:28 +0200
Subject: serial: 8250_pci: Add Realtek 816a and 816b
These serial ports are exposed by the OOB-management-engine on
RealManage-enabled network cards (e.g. AMD DASH enabled systems using
Realtek cards).
Because these have 3 BARs, they fail the "num_iomem <= 1" check in
serial_pci_guess_board.
I've manually checked the two IOMEM regions and BAR 2 doesn't seem to
respond to reads, but BAR 4 seems to be an MMIO version of the IO ports
(untested).
With this change, the ports are detected:
0000:02:00.1: ttyS0 at I/O 0x2200 (irq = 82, base_baud = 115200) is a 16550A
0000:02:00.2: ttyS1 at I/O 0x2100 (irq = 55, base_baud = 115200) is a 16550A
lspci output:
02:00.1 0700: 10ec:816a (rev 0e) (prog-if 02 [16550])
Subsystem: 17aa:5082
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort+ <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 82
IOMMU group: 11
Region 0: I/O ports at 2200 [size=256]
Region 2: Memory at fd715000 (64-bit, non-prefetchable) [size=4K]
Region 4: Memory at fd704000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 01
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s unlimited, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 0.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ NonFatalErr- FatalErr- UnsupReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s unlimited, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp+
LnkCtl: ASPM L1 Enabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Range ABCD, TimeoutDis+ NROPrPrP- LTR+
10BitTagComp- 10BitTagReq- OBFF Via message/WAKE#, ExtFmt- EETLPPrefix-
EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
FRS- TPHComp- ExtTPHComp-
AtomicOpsCap: 32bit- 64bit- 128bitCAS-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis- LTR- OBFF Disabled,
AtomicOpsCtl: ReqEn-
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete- EqualizationPhase1-
EqualizationPhase2- EqualizationPhase3- LinkEqualizationRequest-
Retimer- 2Retimers- CrosslinkRes: unsupported
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Vector table: BAR=4 offset=00000000
PBA: BAR=4 offset=00000800
Capabilities: [d0] Vital Product Data
Not readable
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
AERCap: First Error Pointer: 00, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 00000000 00000000 00000000 00000000
Capabilities: [160 v1] Device Serial Number 00-00-00-00-00-00-00-00
Capabilities: [170 v1] Latency Tolerance Reporting
Max snoop latency: 0ns
Max no snoop latency: 0ns
Capabilities: [178 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
L1SubCtl1: PCI-PM_L1.2- PCI-PM_L1.1- ASPM_L1.2- ASPM_L1.1-
T_CommonMode=0us LTR1.2_Threshold=0ns
L1SubCtl2: T_PwrOn=10us
02:00.2 0700: 10ec:816b (rev 0e)
[...same...]
Signed-off-by: Tobias Diedrich <tobiasdiedrich@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200914173628.GA22508@yamamaya.is-a-geek.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/tty/serial/8250/8250_pci.c | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c
index 3eb2d485eaeb..55bb7b897d97 100644
--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -5566,6 +5566,17 @@ static const struct pci_device_id serial_pci_tbl[] = {
PCI_ANY_ID, PCI_ANY_ID,
0, 0, pbn_wch384_4 },
+ /*
+ * Realtek RealManage
+ */
+ { PCI_VENDOR_ID_REALTEK, 0x816a,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0, pbn_b0_1_115200 },
+
+ { PCI_VENDOR_ID_REALTEK, 0x816b,
+ PCI_ANY_ID, PCI_ANY_ID,
+ 0, 0, pbn_b0_1_115200 },
+
/* Fintek PCI serial cards */
{ PCI_DEVICE(0x1c29, 0x1104), .driver_data = pbn_fintek_4 },
{ PCI_DEVICE(0x1c29, 0x1108), .driver_data = pbn_fintek_8 },
--
2.28.0
reply other threads:[~2020-09-16 17:51 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=160025543941103@kroah.com \
--to=gregkh@linuxfoundation.org \
--cc=stable@vger.kernel.org \
--cc=tobiasdiedrich@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.