From: Rajendra Nayak <rnayak@codeaurora.org>
To: agross@kernel.org, bjorn.andersson@linaro.org, robh+dt@kernel.org
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, sboyd@codeaurora.org,
dianders@chromium.org, mka@chromium.org, kgodara@codeaurora.org,
Rajendra Nayak <rnayak@codeaurora.org>
Subject: [PATCH 3/4] arm64: dts: qcom: sc7280: Define EC and H1 nodes
Date: Tue, 23 Nov 2021 12:30:12 +0530 [thread overview]
Message-ID: <1637650813-16654-4-git-send-email-rnayak@codeaurora.org> (raw)
In-Reply-To: <1637650813-16654-1-git-send-email-rnayak@codeaurora.org>
From: Kshitiz Godara <kgodara@codeaurora.org>
The IDP2 and CRD boards share the EC and H1 parts, so define
all related device nodes into a common file and include them
in the idp2 and crd dts files to avoid duplication.
Signed-off-by: Kshitiz Godara <kgodara@codeaurora.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
---
arch/arm64/boot/dts/qcom/sc7280-crd.dts | 1 +
arch/arm64/boot/dts/qcom/sc7280-ec-h1.dtsi | 110 +++++++++++++++++++++++++++++
arch/arm64/boot/dts/qcom/sc7280-idp2.dts | 1 +
3 files changed, 112 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/sc7280-ec-h1.dtsi
diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
index 09d02c2..8c2aee6 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-crd.dts
@@ -8,6 +8,7 @@
/dts-v1/;
#include "sc7280-idp.dtsi"
+#include "sc7280-ec-h1.dtsi"
/ {
model = "Qualcomm Technologies, Inc. sc7280 CRD platform";
diff --git a/arch/arm64/boot/dts/qcom/sc7280-ec-h1.dtsi b/arch/arm64/boot/dts/qcom/sc7280-ec-h1.dtsi
new file mode 100644
index 0000000..78fb5eb
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-ec-h1.dtsi
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * sc7280 EC/H1 over SPI (common between IDP2 and CRD)
+ *
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ */
+
+ap_ec_spi: &spi10 {
+ status = "okay";
+
+ pinctrl-0 = <&qup_spi10_cs_gpio_init_high>, <&qup_spi10_cs_gpio>;
+ cs-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+
+ cros_ec: ec@0 {
+ compatible = "google,cros-ec-spi";
+ reg = <0>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&ap_ec_int_l>;
+ spi-max-frequency = <3000000>;
+
+ cros_ec_pwm: ec-pwm {
+ compatible = "google,cros-ec-pwm";
+ #pwm-cells = <1>;
+ };
+
+ i2c_tunnel: i2c-tunnel {
+ compatible = "google,cros-ec-i2c-tunnel";
+ google,remote-bus = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ typec {
+ compatible = "google,cros-ec-typec";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usb_c0: connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ label = "left";
+ power-role = "dual";
+ data-role = "host";
+ try-power-role = "source";
+ };
+
+ usb_c1: connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ label = "right";
+ power-role = "dual";
+ data-role = "host";
+ try-power-role = "source";
+ };
+ };
+ };
+};
+
+#include <arm/cros-ec-keyboard.dtsi>
+#include <arm/cros-ec-sbs.dtsi>
+
+ap_h1_spi: &spi14 {
+ status = "okay";
+
+ pinctrl-0 = <&qup_spi14_cs_gpio_init_high>, <&qup_spi14_cs_gpio>;
+ cs-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+
+ cr50: tpm@0 {
+ compatible = "google,cr50";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&h1_ap_int_odl>;
+ spi-max-frequency = <800000>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <104 IRQ_TYPE_EDGE_RISING>;
+ };
+};
+
+&tlmm {
+ ap_ec_int_l: ap-ec-int-l {
+ pins = "gpio18";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ h1_ap_int_odl: h1-ap-int-odl {
+ pins = "gpio104";
+ function = "gpio";
+ input-enable;
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ qup_spi10_cs_gpio_init_high: qup-spi10-cs-gpio-init-high {
+ pins = "gpio43";
+ output-high;
+ drive-strength = <2>;
+ };
+
+ qup_spi14_cs_gpio_init_high: qup-spi14-cs-gpio-init-high {
+ pins = "gpio59";
+ output-high;
+ drive-strength = <2>;
+ };
+};
+
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
index 3ae9969..208ca69 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
@@ -8,6 +8,7 @@
/dts-v1/;
#include "sc7280-idp.dtsi"
+#include "sc7280-ec-h1.dtsi"
/ {
model = "Qualcomm Technologies, Inc. sc7280 IDP SKU2 platform";
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
next prev parent reply other threads:[~2021-11-23 7:00 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-11-23 7:00 [PATCH 0/4] arm64: dts: qcom: Add support for the sc7280 CRD board Rajendra Nayak
2021-11-23 7:00 ` [PATCH 1/4] dt-bindings: arm: qcom: Document qcom,sc7280-crd board Rajendra Nayak
2021-11-23 14:53 ` Matthias Kaehlcke
2021-11-24 11:47 ` Rajendra Nayak
2021-11-23 7:00 ` [PATCH 2/4] arm64: dts: qcom: sc7280-crd: Add device tree files for CRD Rajendra Nayak
2021-11-23 16:14 ` Matthias Kaehlcke
2021-11-24 11:48 ` Rajendra Nayak
2021-11-23 7:00 ` Rajendra Nayak [this message]
2021-11-23 17:40 ` [PATCH 3/4] arm64: dts: qcom: sc7280: Define EC and H1 nodes Matthias Kaehlcke
2021-11-24 11:48 ` Rajendra Nayak
2021-11-23 7:00 ` [PATCH 4/4] arm64: dts: qcom: sc7280-crd: Add Touchscreen and touchpad support Rajendra Nayak
2021-11-23 17:58 ` Matthias Kaehlcke
2021-11-24 11:49 ` Rajendra Nayak
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1637650813-16654-4-git-send-email-rnayak@codeaurora.org \
--to=rnayak@codeaurora.org \
--cc=agross@kernel.org \
--cc=bjorn.andersson@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=dianders@chromium.org \
--cc=kgodara@codeaurora.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mka@chromium.org \
--cc=robh+dt@kernel.org \
--cc=sboyd@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.