All of lore.kernel.org
 help / color / mirror / Atom feed
From: Vincent Shih <vincent.sunplus@gmail.com>
To: gregkh@linuxfoundation.org, stern@rowland.harvard.edu,
	p.zabel@pengutronix.de, linux-kernel@vger.kernel.org,
	linux-usb@vger.kernel.org, robh+dt@kernel.org,
	devicetree@vger.kernel.org, wells.lu@sunplus.com
Cc: Vincent Shih <vincent.sunplus@gmail.com>
Subject: [PATCH v2 1/2] usb: host: ehci-sunplus: Add driver for ehci in Sunplus SP7021
Date: Sun, 27 Feb 2022 17:50:40 +0800	[thread overview]
Message-ID: <1645955441-6496-2-git-send-email-vincent.sunplus@gmail.com> (raw)
In-Reply-To: <1645955441-6496-1-git-send-email-vincent.sunplus@gmail.com>

Add driver for ehci in Sunplus SP7021

Signed-off-by: Vincent Shih <vincent.sunplus@gmail.com>
---
Changes in v2:
  - Address the comments by Rob Herring.
  - Clean up codes.

 MAINTAINERS                     |   6 +
 drivers/usb/host/Kconfig        |  11 +
 drivers/usb/host/Makefile       |   1 +
 drivers/usb/host/ehci-sunplus.c | 495 ++++++++++++++++++++++++++++++++++++++++
 4 files changed, 513 insertions(+)
 create mode 100644 drivers/usb/host/ehci-sunplus.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 80eebc1..6c2faf3 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -17947,6 +17947,12 @@ L:	netdev@vger.kernel.org
 S:	Maintained
 F:	drivers/net/ethernet/dlink/sundance.c
 
+SUNPLUS USB EHCI DRIVER
+M:	Vincent Shih <vincent.sunplus@gmail.com>
+L:	linux-usb@vger.kernel.org
+S:	Maintained
+F:	drivers/usb/host/ehci-sunplus.c
+
 SUPERH
 M:	Yoshinori Sato <ysato@users.sourceforge.jp>
 M:	Rich Felker <dalias@libc.org>
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index c4736d1..9728d3b 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -339,6 +339,17 @@ config USB_OCTEON_EHCI
 	  USB 2.0 device support.  All CN6XXX based chips with USB are
 	  supported.
 
+config USB_EHCI_SUNPLUS
+	tristate "EHCI support for Sunplus USB controller"
+	depends on SOC_SP7021
+	select NVMEM_SUNPLUS_OCOTP
+	help
+	  Enables support for the on-chip EHCI controller in Sunplus
+	  SoCs. It supports 32-bit AHB/AXI config bus and 64-bit AXI
+	  data bus.
+	  This driver can also be built as a module. If so, the module
+	  will be called ehci-sunplus.
+
 endif # USB_EHCI_HCD
 
 config USB_OXU210HP_HCD
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 171de4d..7e9b5f1 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -46,6 +46,7 @@ obj-$(CONFIG_USB_EHCI_HCD_STI)	+= ehci-st.o
 obj-$(CONFIG_USB_EHCI_EXYNOS)	+= ehci-exynos.o
 obj-$(CONFIG_USB_EHCI_HCD_AT91) += ehci-atmel.o
 obj-$(CONFIG_USB_EHCI_BRCMSTB)	+= ehci-brcm.o
+obj-$(CONFIG_USB_EHCI_SUNPLUS)	+= ehci-sunplus.o
 
 obj-$(CONFIG_USB_OXU210HP_HCD)	+= oxu210hp-hcd.o
 obj-$(CONFIG_USB_ISP116X_HCD)	+= isp116x-hcd.o
diff --git a/drivers/usb/host/ehci-sunplus.c b/drivers/usb/host/ehci-sunplus.c
new file mode 100644
index 0000000..54a5a16
--- /dev/null
+++ b/drivers/usb/host/ehci-sunplus.c
@@ -0,0 +1,495 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/*
+ * The EHCI driver for Sunplus SP7021
+ *
+ * Copyright (C) 2021 Sunplus Technology Inc., All rights reserved.
+ *
+ * Note 1 : non-posted write command for the registers accesses of
+ * Sunplus SP7021.
+ *
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/usb.h>
+#include <linux/usb/ehci_pdriver.h>
+#include <linux/usb/hcd.h>
+
+#include "ehci.h"
+
+#define RF_MASK_V(mask, val)			(((mask) << 16) | (val))
+#define RF_MASK_V_CLR(mask)			(((mask) << 16) | 0)
+
+#define USB_PORT0_ID				0
+#define USB_PORT1_ID				1
+#define USB_PORT_NUM				2
+
+#define MASK_BITS				0xffff
+
+#define OTP_DISC_LEVEL_DEFAULT			0xd
+#define OTP_DISC_LEVEL_BITS			0x5
+
+// GROUP 140/150 UPHY0/UPHY1
+#define CONFIG1					0x4
+#define J_HS_TX_PWRSAV				BIT(5)
+#define CONFIG3					0xc
+#define J_FORCE_DISC_ON				BIT(5)
+#define J_DEBUG_CTRL_ADDR_MACRO			BIT(0)
+#define CONFIG7					0x1c
+#define J_DISC					0x1f
+#define CONFIG9					0x24
+#define J_ECO_PATH				BIT(6)
+#define CONFIG16				0x40
+#define J_TBCWAIT_MASK				GENMASK(6, 5)
+#define J_TBCWAIT_1P1_MS			FIELD_PREP(J_TBCWAIT_MASK, 0)
+#define J_TVDM_SRC_DIS_MASK			GENMASK(4, 3)
+#define J_TVDM_SRC_DIS_8P2_MS			FIELD_PREP(J_TVDM_SRC_DIS_MASK, 3)
+#define J_TVDM_SRC_EN_MASK			GENMASK(2, 1)
+#define J_TVDM_SRC_EN_1P6_MS			FIELD_PREP(J_TVDM_SRC_EN_MASK, 0)
+#define J_BC_EN					BIT(0)
+#define CONFIG17				0x44
+#define IBG_TRIM0_MASK				GENMASK(7, 5)
+#define IBG_TRIM0_SSLVHT			FIELD_PREP(IBG_TRIM0_MASK, 4)
+#define J_VDATREE_TRIM_MASK			GENMASK(4, 1)
+#define J_VDATREE_TRIM_DEFAULT			FIELD_PREP(J_VDATREE_TRIM_MASK, 9)
+#define CONFIG23				0x5c
+#define PROB_MASK				GENMASK(5, 3)
+#define PROB					FIELD_PREP(PROB_MASK, 7)
+
+// GROUP 4 MOON 4
+#define USBC_CONTROL				0x44
+#define MO1_USBC1_USB0_SEL			BIT(13)
+#define MO1_USBC1_USB0_CTRL			BIT(12)
+#define MO1_USBC0_USB0_SEL			BIT(5)
+#define MO1_USBC0_USB0_CTRL			BIT(4)
+#define UPHY0_CONTROL0				0x48
+#define UPHY0_CONTROL1				0x4c
+#define UPHY0_CONTROL2				0x50
+#define MO1_UPHY0_RX_CLK_SEL			BIT(6)
+#define UPHY0_CONTROL3				0x54
+#define MO1_UPHY0_PLL_POWER_OFF_SEL		BIT(7)
+#define MO1_UPHY0_PLL_POWER_OFF			BIT(3)
+#define UPHY1_CONTROL0				0x58
+#define UPHY1_CONTROL1				0x5c
+#define UPHY1_CONTROL2				0x60
+#define MO1_UPHY1_RX_CLK_SEL			BIT(6)
+#define UPHY1_CONTROL3				0x64
+#define MO1_UPHY1_PLL_POWER_OFF_SEL		BIT(7)
+#define MO1_UPHY1_PLL_POWER_OFF			BIT(3)
+
+#define hcd_to_sp_ehci_priv(h) \
+		((struct sp_ehci_priv *)hcd_to_ehci(h)->priv)
+
+struct sp_ehci_priv {
+	struct resource *uphy_res_mem;
+	struct resource *moon4_res_mem;
+	struct clk *phy_clk;
+	struct clk *ehci_clk;
+	struct reset_control *phy_rstc;
+	struct reset_control *ehci_rstc;
+	void __iomem *uphy_regs;
+	void __iomem *moon4_regs;
+	u32 port_num;
+};
+
+static int ehci_sunplus_reset(struct usb_hcd *hcd)
+{
+	struct platform_device *pdev = to_platform_device(hcd->self.controller);
+	struct usb_ehci_pdata *pdata = pdev->dev.platform_data;
+	struct ehci_hcd *ehci = hcd_to_ehci(hcd);
+	int retval;
+
+	hcd->has_tt = pdata->has_tt;
+	ehci->has_synopsys_hc_bug = pdata->has_synopsys_hc_bug;
+	ehci->big_endian_desc = pdata->big_endian_desc;
+	ehci->big_endian_mmio = pdata->big_endian_mmio;
+
+	ehci->caps = hcd->regs + pdata->caps_offset;
+	retval = ehci_setup(hcd);
+
+	return retval;
+}
+
+static struct hc_driver __read_mostly ehci_sunplus_driver;
+
+static const struct ehci_driver_overrides ehci_sunplus_overrides __initconst = {
+	.reset =		ehci_sunplus_reset,
+	.extra_priv_size =	sizeof(struct sp_ehci_priv),
+};
+
+static void pll_power(struct sp_ehci_priv *sp_priv, u32 par1, u32 par2, u32 par3)
+{
+	u32 pll_pwr_on, pll_pwr_off;
+
+	pll_pwr_off = (readl(sp_priv->moon4_regs + par1) & ~MASK_BITS) | par2 | par3;
+	pll_pwr_on = (readl(sp_priv->moon4_regs + par1) & ~MASK_BITS) | par2;
+
+	writel(RF_MASK_V(MASK_BITS, pll_pwr_off), sp_priv->moon4_regs + par1);
+	mdelay(1);
+	writel(RF_MASK_V(MASK_BITS, pll_pwr_on), sp_priv->moon4_regs + par1);
+	mdelay(1);
+	writel(RF_MASK_V(MASK_BITS, pll_pwr_off), sp_priv->moon4_regs + par1);
+	mdelay(1);
+	writel(RF_MASK_V(MASK_BITS, pll_pwr_on), sp_priv->moon4_regs + par1);
+	mdelay(1);
+	writel(RF_MASK_V(MASK_BITS, 0x0), sp_priv->moon4_regs + par1);
+}
+
+static int internal_modification(struct device *dev, struct sp_ehci_priv *sp_priv)
+{
+	struct nvmem_cell *cell;
+	char *disc_name = "disc_vol";
+	ssize_t otp_l = 0;
+	char *otp_v;
+	u32 set, val;
+
+	cell = nvmem_cell_get(dev, disc_name);
+	if (IS_ERR_OR_NULL(cell)) {
+		if (PTR_ERR(cell) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+	}
+
+	otp_v = nvmem_cell_read(cell, &otp_l);
+	nvmem_cell_put(cell);
+
+	if (otp_v) {
+		if (sp_priv->port_num == USB_PORT0_ID)
+			set = *otp_v & J_DISC;
+		else if (sp_priv->port_num == USB_PORT1_ID)
+			set = ((*otp_v >> OTP_DISC_LEVEL_BITS) |
+				(*(otp_v + 1) << (sizeof(char) * 8 - OTP_DISC_LEVEL_BITS)))
+				& J_DISC;
+	}
+
+	if (!otp_v || set == 0)
+		set = OTP_DISC_LEVEL_DEFAULT;
+
+	val = readl(sp_priv->uphy_regs + CONFIG7);
+	val = (val & ~J_DISC) | set;
+	writel(val, sp_priv->uphy_regs + CONFIG7);
+
+	val = readl(sp_priv->uphy_regs + CONFIG9);
+	val &= ~(J_ECO_PATH);
+	writel(val, sp_priv->uphy_regs + CONFIG9);
+
+	val = readl(sp_priv->uphy_regs + CONFIG1);
+	val &= ~(J_HS_TX_PWRSAV);
+	writel(val, sp_priv->uphy_regs + CONFIG1);
+
+	val = readl(sp_priv->uphy_regs + CONFIG23);
+	val = (val & ~PROB) | PROB;
+	writel(val, sp_priv->uphy_regs + CONFIG23);
+
+	return 0;
+}
+
+static int uphy0_init(struct platform_device *pdev, struct sp_ehci_priv *sp_priv)
+{
+	u32 par1, par2, par3;
+	int retval;
+
+	/* Default value modification */
+	writel(RF_MASK_V(MASK_BITS, 0x4002), sp_priv->moon4_regs + UPHY0_CONTROL0);
+	writel(RF_MASK_V(MASK_BITS, 0x8747), sp_priv->moon4_regs + UPHY0_CONTROL1);
+
+	/* PLL power off/on twice */
+	par1 = UPHY0_CONTROL3;
+	par2 = MO1_UPHY0_PLL_POWER_OFF_SEL;
+	par3 = MO1_UPHY0_PLL_POWER_OFF;
+	pll_power(sp_priv, par1, par2, par3);
+
+	/* board uphy 0 internal register modification for tid certification */
+	retval = internal_modification(&pdev->dev, sp_priv);
+
+	/* port 0 uphy clk fix */
+	writel(RF_MASK_V(MO1_UPHY0_RX_CLK_SEL, MO1_UPHY0_RX_CLK_SEL),
+	       sp_priv->moon4_regs + UPHY0_CONTROL2);
+
+	/* switch to host */
+	writel(RF_MASK_V(MO1_USBC0_USB0_SEL | MO1_USBC0_USB0_CTRL,
+			 MO1_USBC0_USB0_SEL | MO1_USBC0_USB0_CTRL),
+	       sp_priv->moon4_regs + USBC_CONTROL);
+
+	return retval;
+}
+
+static int uphy1_init(struct platform_device *pdev, struct sp_ehci_priv *sp_priv)
+{
+	u32 par1, par2, par3;
+	int retval;
+
+	/* Default value modification */
+	writel(RF_MASK_V(MASK_BITS, 0x4002), sp_priv->moon4_regs + UPHY1_CONTROL0);
+	writel(RF_MASK_V(MASK_BITS, 0x8747), sp_priv->moon4_regs + UPHY1_CONTROL1);
+
+	/* PLL power off/on twice */
+	par1 = UPHY1_CONTROL3;
+	par2 = MO1_UPHY1_PLL_POWER_OFF_SEL;
+	par3 = MO1_UPHY1_PLL_POWER_OFF;
+	pll_power(sp_priv, par1, par2, par3);
+
+	/* board uphy 1 internal register modification for tid certification */
+	retval = internal_modification(&pdev->dev, sp_priv);
+
+	/* port 1 uphy clk fix */
+	writel(RF_MASK_V(MO1_UPHY1_RX_CLK_SEL, MO1_UPHY1_RX_CLK_SEL),
+	       sp_priv->moon4_regs + UPHY1_CONTROL2);
+
+	/* switch to host */
+	writel(RF_MASK_V(MO1_USBC1_USB0_SEL | MO1_USBC1_USB0_CTRL,
+			 MO1_USBC1_USB0_SEL | MO1_USBC1_USB0_CTRL),
+	       sp_priv->moon4_regs + USBC_CONTROL);
+
+	return retval;
+}
+
+static struct usb_ehci_pdata usb_ehci_pdata = {
+};
+
+static int ehci_sunplus_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct sp_ehci_priv *sp_priv;
+	struct resource *res_mem;
+	struct usb_hcd *hcd;
+	int irq, ret;
+
+	if (usb_disabled())
+		return -ENODEV;
+
+	pdev->dev.platform_data = &usb_ehci_pdata;
+
+	/* initialize hcd */
+	hcd = usb_create_hcd(&ehci_sunplus_driver, dev, dev_name(dev));
+	if (!hcd)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, hcd);
+	sp_priv = hcd_to_sp_ehci_priv(hcd);
+
+	/* initialize uphy0/uphy1 */
+	sp_priv->uphy_res_mem = platform_get_resource_byname(pdev, IORESOURCE_MEM, "uphy");
+	sp_priv->uphy_regs = devm_ioremap_resource(dev, sp_priv->uphy_res_mem);
+
+	if (IS_ERR(sp_priv->uphy_regs))
+		return PTR_ERR(sp_priv->uphy_regs);
+
+	sp_priv->moon4_res_mem = platform_get_resource_byname(pdev, IORESOURCE_MEM, "moon4");
+	sp_priv->moon4_regs = devm_ioremap(dev, sp_priv->moon4_res_mem->start,
+					   resource_size(sp_priv->moon4_res_mem));
+	if (IS_ERR(sp_priv->moon4_regs))
+		return PTR_ERR(sp_priv->moon4_regs);
+
+	sp_priv->phy_clk = devm_clk_get(dev, "uphy_clk");
+
+	if (IS_ERR(sp_priv->phy_clk)) {
+		ret = PTR_ERR(sp_priv->phy_clk);
+		goto err_put_hcd;
+	}
+
+	sp_priv->phy_rstc = devm_reset_control_get_exclusive(dev, "uphy_rst");
+	if (IS_ERR(sp_priv->phy_rstc)) {
+		ret = PTR_ERR(sp_priv->phy_rstc);
+		goto err_put_hcd;
+	}
+
+	ret = clk_prepare_enable(sp_priv->phy_clk);
+	if (ret)
+		goto err_put_hcd;
+
+	ret = reset_control_deassert(sp_priv->phy_rstc);
+	if (ret)
+		goto err_phy_reset;
+
+	ret = of_property_read_u32(pdev->dev.of_node, "port-num", &sp_priv->port_num);
+	if (ret == 0) {
+		if (sp_priv->port_num == USB_PORT0_ID)
+			ret = uphy0_init(pdev, sp_priv);
+		else if (sp_priv->port_num == USB_PORT1_ID)
+			ret = uphy1_init(pdev, sp_priv);
+	}
+
+	if (ret < 0)
+		goto err_phy_clk;
+
+	/* battery charger */
+	writel(J_TBCWAIT_1P1_MS | J_TVDM_SRC_DIS_8P2_MS | J_TVDM_SRC_EN_1P6_MS | J_BC_EN,
+	       sp_priv->uphy_regs + CONFIG16);
+	writel(IBG_TRIM0_SSLVHT | J_VDATREE_TRIM_DEFAULT, sp_priv->uphy_regs + CONFIG17);
+
+	/* chirp mode */
+	writel(J_FORCE_DISC_ON | J_DEBUG_CTRL_ADDR_MACRO, sp_priv->uphy_regs + CONFIG3);
+
+	/* ehci */
+	res_mem = platform_get_resource_byname(pdev, IORESOURCE_MEM, "usbc");
+	hcd->regs = devm_ioremap_resource(dev, res_mem);
+	if (IS_ERR(hcd->regs)) {
+		ret = PTR_ERR(hcd->regs);
+		goto err_phy_clk;
+	}
+
+	hcd->rsrc_start = res_mem->start;
+	hcd->rsrc_len = resource_size(res_mem);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		ret = irq;
+		goto err_phy_clk;
+	}
+	dev_dbg(&pdev->dev, "ehci_id:%d,irq:%d\n", pdev->id, irq);
+
+	sp_priv->ehci_clk = devm_clk_get(dev, "usbc_clk");
+
+	if (IS_ERR(sp_priv->ehci_clk)) {
+		ret = PTR_ERR(sp_priv->ehci_clk);
+		goto err_phy_clk;
+	}
+
+	sp_priv->ehci_rstc = devm_reset_control_get_exclusive(dev, "usbc_rst");
+	if (IS_ERR(sp_priv->ehci_rstc)) {
+		ret = PTR_ERR(sp_priv->ehci_rstc);
+		goto err_put_hcd;
+	}
+
+	ret = clk_prepare_enable(sp_priv->ehci_clk);
+	if (ret)
+		goto err_phy_reset;
+
+	ret = reset_control_deassert(sp_priv->ehci_rstc);
+	if (ret)
+		goto err_ehci_reset;
+
+	ret = usb_add_hcd(hcd, irq, IRQF_SHARED);
+	if (ret)
+		goto err_ehci_clk;
+
+	dev_dbg(dev, "hcd_irq:%d,%d\n", hcd->irq, irq);
+
+	return ret;
+
+err_ehci_reset:
+	reset_control_assert(sp_priv->ehci_rstc);
+err_ehci_clk:
+	clk_disable_unprepare(sp_priv->ehci_clk);
+err_phy_reset:
+	reset_control_assert(sp_priv->phy_rstc);
+err_phy_clk:
+	clk_disable_unprepare(sp_priv->phy_clk);
+err_put_hcd:
+	usb_put_hcd(hcd);
+
+	return ret;
+}
+
+static int ehci_sunplus_remove(struct platform_device *pdev)
+{
+	struct usb_hcd *hcd = platform_get_drvdata(pdev);
+	struct sp_ehci_priv *sp_priv = hcd_to_sp_ehci_priv(hcd);
+	u32 val;
+
+	usb_remove_hcd(hcd);
+
+	/* disable battery charger CDP */
+	val = readl(sp_priv->uphy_regs + CONFIG16);
+	val &= ~J_BC_EN;
+	writel(val, sp_priv->uphy_regs + CONFIG16);
+
+	usb_put_hcd(hcd);
+
+	reset_control_assert(sp_priv->ehci_rstc);
+	clk_disable_unprepare(sp_priv->ehci_clk);
+	reset_control_assert(sp_priv->phy_rstc);
+	clk_disable_unprepare(sp_priv->phy_clk);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int ehci_sunplus_drv_suspend(struct device *dev)
+{
+	struct usb_hcd *hcd = dev_get_drvdata(dev);
+	struct sp_ehci_priv *sp_priv = hcd_to_sp_ehci_priv(hcd);
+	bool do_wakeup = device_may_wakeup(dev);
+	int rc;
+
+	rc = ehci_suspend(hcd, do_wakeup);
+	if (rc)
+		return rc;
+
+	reset_control_assert(sp_priv->ehci_rstc);
+	clk_disable_unprepare(sp_priv->ehci_clk);
+	reset_control_assert(sp_priv->phy_rstc);
+	clk_disable_unprepare(sp_priv->phy_clk);
+
+	return 0;
+}
+
+static int ehci_sunplus_drv_resume(struct device *dev)
+{
+	struct usb_hcd *hcd = dev_get_drvdata(dev);
+	struct sp_ehci_priv *sp_priv = hcd_to_sp_ehci_priv(hcd);
+
+	clk_prepare_enable(sp_priv->phy_clk);
+	reset_control_deassert(sp_priv->phy_rstc);
+	clk_prepare_enable(sp_priv->ehci_clk);
+	reset_control_deassert(sp_priv->ehci_rstc);
+
+	ehci_resume(hcd, false);
+
+	return 0;
+}
+
+static const struct dev_pm_ops ehci_sunplus_pm_ops = {
+	.suspend = ehci_sunplus_drv_suspend,
+	.resume = ehci_sunplus_drv_resume,
+};
+#endif
+
+static const struct of_device_id ehci_sunplus_dt_ids[] = {
+	{ .compatible = "sunplus,sp7021-usb-ehci" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, ehci_sunplus_dt_ids);
+
+static struct platform_driver ehci_hcd_sunplus_driver = {
+	.probe			= ehci_sunplus_probe,
+	.remove			= ehci_sunplus_remove,
+	.shutdown		= usb_hcd_platform_shutdown,
+	.driver = {
+		.name		= "ehci-sunplus",
+		.of_match_table = ehci_sunplus_dt_ids,
+#ifdef CONFIG_PM
+		.pm = &ehci_sunplus_pm_ops,
+#endif
+	}
+};
+
+static int __init ehci_sunplus_init(void)
+{
+	if (usb_disabled())
+		return -ENODEV;
+
+	ehci_init_driver(&ehci_sunplus_driver, &ehci_sunplus_overrides);
+	return platform_driver_register(&ehci_hcd_sunplus_driver);
+}
+module_init(ehci_sunplus_init);
+
+static void __exit ehci_sunplus_cleanup(void)
+{
+	platform_driver_unregister(&ehci_hcd_sunplus_driver);
+}
+module_exit(ehci_sunplus_cleanup);
+
+MODULE_AUTHOR("Vincent Shih <vincent.sunplus@gmail.com>");
+MODULE_DESCRIPTION("Sunplus USB EHCI driver");
+MODULE_LICENSE("GPL");
+
-- 
2.7.4


  reply	other threads:[~2022-02-27  9:50 UTC|newest]

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2022-02-27  9:50 [PATCH v2 0/2] Add driver for ehci in Sunplus SP7021 Vincent Shih
2022-02-27  9:50 ` Vincent Shih [this message]
2022-02-27 16:07   ` [PATCH v2 1/2] usb: host: ehci-sunplus: " Alan Stern
2022-02-27  9:50 ` [PATCH v2 2/2] dt-bindings: usb: Add bindings doc for Sunplus EHCI driver Vincent Shih
2022-02-27 10:53   ` Krzysztof Kozlowski
2022-02-28  2:44   ` Rob Herring

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1645955441-6496-2-git-send-email-vincent.sunplus@gmail.com \
    --to=vincent.sunplus@gmail.com \
    --cc=devicetree@vger.kernel.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=robh+dt@kernel.org \
    --cc=stern@rowland.harvard.edu \
    --cc=wells.lu@sunplus.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.