From: <gregkh@linuxfoundation.org>
To: krzysztof.kozlowski@linaro.org, luiz.von.dentz@intel.com,
stable@vger.kernel.org
Cc: <stable@vger.kernel.org>
Subject: FAILED: patch "[PATCH] Bluetooth: hci_qca: Fix driver shutdown on closed serdev" failed to apply to 5.10-stable tree
Date: Sat, 21 Jan 2023 11:33:23 +0100 [thread overview]
Message-ID: <167429720372200@kroah.com> (raw)
The patch below does not apply to the 5.10-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable@vger.kernel.org>.
Possible dependencies:
272970be3dab ("Bluetooth: hci_qca: Fix driver shutdown on closed serdev")
thanks,
greg k-h
------------------ original commit in Linus's tree ------------------
From 272970be3dabd24cbe50e393ffee8f04aec3b9a8 Mon Sep 17 00:00:00 2001
From: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Date: Thu, 29 Dec 2022 11:28:29 +0100
Subject: [PATCH] Bluetooth: hci_qca: Fix driver shutdown on closed serdev
The driver shutdown callback (which sends EDL_SOC_RESET to the device
over serdev) should not be invoked when HCI device is not open (e.g. if
hci_dev_open_sync() failed), because the serdev and its TTY are not open
either. Also skip this step if device is powered off
(qca_power_shutdown()).
The shutdown callback causes use-after-free during system reboot with
Qualcomm Atheros Bluetooth:
Unable to handle kernel paging request at virtual address
0072662f67726fd7
...
CPU: 6 PID: 1 Comm: systemd-shutdow Tainted: G W
6.1.0-rt5-00325-g8a5f56bcfcca #8
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
tty_driver_flush_buffer+0x4/0x30
serdev_device_write_flush+0x24/0x34
qca_serdev_shutdown+0x80/0x130 [hci_uart]
device_shutdown+0x15c/0x260
kernel_restart+0x48/0xac
KASAN report:
BUG: KASAN: use-after-free in tty_driver_flush_buffer+0x1c/0x50
Read of size 8 at addr ffff16270c2e0018 by task systemd-shutdow/1
CPU: 7 PID: 1 Comm: systemd-shutdow Not tainted
6.1.0-next-20221220-00014-gb85aaf97fb01-dirty #28
Hardware name: Qualcomm Technologies, Inc. Robotics RB5 (DT)
Call trace:
dump_backtrace.part.0+0xdc/0xf0
show_stack+0x18/0x30
dump_stack_lvl+0x68/0x84
print_report+0x188/0x488
kasan_report+0xa4/0xf0
__asan_load8+0x80/0xac
tty_driver_flush_buffer+0x1c/0x50
ttyport_write_flush+0x34/0x44
serdev_device_write_flush+0x48/0x60
qca_serdev_shutdown+0x124/0x274
device_shutdown+0x1e8/0x350
kernel_restart+0x48/0xb0
__do_sys_reboot+0x244/0x2d0
__arm64_sys_reboot+0x54/0x70
invoke_syscall+0x60/0x190
el0_svc_common.constprop.0+0x7c/0x160
do_el0_svc+0x44/0xf0
el0_svc+0x2c/0x6c
el0t_64_sync_handler+0xbc/0x140
el0t_64_sync+0x190/0x194
Fixes: 7e7bbddd029b ("Bluetooth: hci_qca: Fix qca6390 enable failure after warm reboot")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 6eddc23e49d9..bbe9cf1cae27 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -2164,10 +2164,17 @@ static void qca_serdev_shutdown(struct device *dev)
int timeout = msecs_to_jiffies(CMD_TRANS_TIMEOUT_MS);
struct serdev_device *serdev = to_serdev_device(dev);
struct qca_serdev *qcadev = serdev_device_get_drvdata(serdev);
+ struct hci_uart *hu = &qcadev->serdev_hu;
+ struct hci_dev *hdev = hu->hdev;
+ struct qca_data *qca = hu->priv;
const u8 ibs_wake_cmd[] = { 0xFD };
const u8 edl_reset_soc_cmd[] = { 0x01, 0x00, 0xFC, 0x01, 0x05 };
if (qcadev->btsoc_type == QCA_QCA6390) {
+ if (test_bit(QCA_BT_OFF, &qca->flags) ||
+ !test_bit(HCI_RUNNING, &hdev->flags))
+ return;
+
serdev_device_write_flush(serdev);
ret = serdev_device_write_buf(serdev, ibs_wake_cmd,
sizeof(ibs_wake_cmd));
reply other threads:[~2023-01-21 10:35 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=167429720372200@kroah.com \
--to=gregkh@linuxfoundation.org \
--cc=krzysztof.kozlowski@linaro.org \
--cc=luiz.von.dentz@intel.com \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.