From: Steven Walter <srwalter@hapablap.dyn.dhs.org>
To: Martin Mares <mj@suse.cz>
Cc: linux-kernel@vger.kernel.org
Subject: Re: "No IRQ known for interrupt pin A..." error message
Date: Sun, 19 Nov 2000 15:18:38 -0600 [thread overview]
Message-ID: <20001119151838.A2104@hapablap.dyn.dhs.org> (raw)
In-Reply-To: <20001118181110.A424@hapablap.dyn.dhs.org> <20001119202033.A272@albireo.ucw.cz>
In-Reply-To: <20001119202033.A272@albireo.ucw.cz>; from mj@suse.cz on Sun, Nov 19, 2000 at 08:20:33PM +0100
On Sun, Nov 19, 2000 at 08:20:33PM +0100, Martin Mares wrote:
> > During boot, I get the message:
> >
> > PCI: No IRQ known for interrupt pin A of device 00:00.1. Please try
> > using pci=biosirq.
>
> Can you send me 'lspci -vvx' output, please?
>
Here you go:
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 530 Host (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 32 set
Region 0: Memory at ec000000 (32-bit, non-prefetchable)
Capabilities: [c0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=21
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
00: 39 10 30 05 07 00 10 22 03 00 00 06 00 20 80 00
10: 00 00 00 ec 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 c0 00 00 00 00 00 00 00 00 00 00 00
00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0) (prog-if 80 [Master])
Subsystem: Silicon Integrated Systems [SiS]: Unknown device 5513
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 128 set
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 01f0
Region 1: I/O ports at 03f4
Region 2: I/O ports at 0170
Region 3: I/O ports at 0374
Region 4: I/O ports at ffa0
00: 39 10 13 55 05 00 00 00 d0 80 01 01 00 80 80 00
10: f1 01 00 00 f5 03 00 00 71 01 00 00 75 03 00 00
20: a1 ff 00 00 00 00 00 00 00 00 00 00 39 10 13 55
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 01 00 00
00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513 (rev b1)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
00: 39 10 08 00 0f 00 00 02 b1 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:01.1 Class ff00: Silicon Integrated Systems [SiS] ACPI
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00: 39 10 09 00 00 00 00 02 00 00 00 ff 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00:01.2 USB Controller: Silicon Integrated Systems [SiS] 7001 (rev 11) (prog-if 10 [OHCI])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 80 max, 32 set
Interrupt: pin A routed to IRQ 9
Region 0: Memory at efffe000 (32-bit, non-prefetchable)
00: 39 10 01 70 17 01 80 02 11 10 03 0c 00 20 80 00
10: 00 e0 ff ef 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 09 01 00 50
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] 5591/5592 AGP (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: ebe00000-ebefffff
Prefetchable memory behind bridge: fec00000-ffcfffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00: 39 10 01 00 07 00 00 00 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 c0 c0 00 00
20: e0 eb e0 eb c0 fe c0 ff 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0c 00
00:0b.0 Ethernet controller: Davicom Semiconductor, Inc. Ethernet 100/10 MBit (rev 10)
Subsystem: Unknown device 0291:8212
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 20 min, 40 max, 32 set
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at da00
Region 1: Memory at efffff80 (32-bit, non-prefetchable)
Expansion ROM at eff80000 [disabled]
Capabilities: [50] Power Management version 1
Flags: PMEClk- AuxPwr+ DSI+ D1- D2- PME-
Status: D0 PME-Enable+ DSel=0 DScale=0 PME+
00: 82 12 02 91 07 01 90 02 10 00 00 02 00 20 00 00
10: 01 da 00 00 80 ff ff ef 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 91 02 12 82
30: 00 00 f8 ef 50 00 00 00 00 00 00 00 0a 01 14 28
00:0c.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: C-Media Electronics Inc: Unknown device 0111
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 2 min, 24 max, 32 set
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at dc00
Capabilities: [c0] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: f6 13 11 01 05 01 10 02 10 00 01 04 00 20 80 00
10: 01 dc 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 f6 13 11 01
30: 00 00 00 00 c0 00 00 00 00 00 00 00 0b 01 02 18
00:0c.1 Communication controller: C-Media Electronics Inc: Unknown device 0211 (rev 10)
Subsystem: C-Media Electronics Inc: Unknown device 0211
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at de00
Capabilities: [40] Power Management version 2
Flags: PMEClk+ AuxPwr- DSI- D1- D2+ PME+
Status: D3 PME-Enable+ DSel=0 DScale=0 PME+
00: f6 13 11 02 01 00 10 02 10 00 80 07 00 00 00 00
10: 01 de 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 f6 13 11 02
30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 02 00 00
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 6306 3D-AGP (rev a3) (prog-if 00 [VGA])
Subsystem: Silicon Integrated Systems [SiS]: Unknown device 6306
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 2 min, 32 set
Region 0: Memory at ff000000 (32-bit, prefetchable)
Region 1: Memory at ebef0000 (32-bit, non-prefetchable)
Region 2: I/O ports at cc00
Capabilities: [40] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1- D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 1.0
Status: RQ=1 SBA- 64bit- FW- Rate=21
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
00: 39 10 06 63 07 00 30 02 a3 00 00 03 00 20 00 00
10: 08 00 00 ff 00 00 ef eb 01 cc 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 39 10 06 63
30: 00 00 00 00 40 00 00 00 00 00 00 00 00 00 02 00
Hope its useful to you.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
next prev parent reply other threads:[~2000-11-19 21:50 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2000-11-19 0:11 "No IRQ known for interrupt pin A..." error message Steven Walter
2000-11-19 19:20 ` Martin Mares
2000-11-19 20:01 ` Alex Romosan
2000-11-20 0:18 ` Gerhard Mack
2000-11-20 1:32 ` Alex Romosan
2000-11-19 21:18 ` Steven Walter [this message]
2000-11-21 15:09 ` rob
-- strict thread matches above, loose matches on Subject: below --
2000-11-19 21:50 Pavel Rabel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20001119151838.A2104@hapablap.dyn.dhs.org \
--to=srwalter@hapablap.dyn.dhs.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mj@suse.cz \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.