From: Andy Galasso <andy@adgsoftware.com>
To: linux-kernel@vger.kernel.org
Subject: Promise PDC20267 irq timeout
Date: Mon, 1 Jan 2001 17:07:41 -0500 [thread overview]
Message-ID: <20010101170741.A14537@adgsoftware.com> (raw)
I'm attempting to use a Promise FastTrak100 in native Ultra100 mode. Anyone
have any idea how to get this working?
Linux-2.4.0-prerelease SMP
Promise FastTrak100 - no array defined in adapter BIOS
4 IBM DTLA-307030 drives
boot params: ide2=0xac00 ide3=0xb400
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686a IDE UDMA66 controller on pci0:7.1
ide0: BM-DMA at 0x9000-0x9007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x9008-0x900f, BIOS settings: hdc:DMA, hdd:pio
PDC20267: IDE controller on PCI bus 00 dev 70
PDC20267: chipset revision 2
PDC20267: not 100% native mode: will probe irqs later
PDC20267: (U)DMA Burst Bit ENABLED Primary MASTER Mode Secondary MASTER Mode.
PDC20267: neither IDE port enabled (BIOS)
hde: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
hde: IBM-DTLA-307030, ATA DISK drive
hdf: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
hdf: IBM-DTLA-307030, ATA DISK drive
hdg: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
hdg: IBM-DTLA-307030, ATA DISK drive
hdh: probing with STATUS(0x50) instead of ALTSTATUS(0xff)
hdh: IBM-DTLA-307030, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xac00-0xac07,0xae06 on irq 16
ide3 at 0xb400-0xb407,0xb606 on irq 16 (shared with ide2)
hde: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63
hdf: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63
hdg: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63
hdh: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63
Partition check:
hde:hde: irq timeout: status=0x50 { DriveReady SeekComplete }
hde: irq timeout: status=0x50 { DriveReady SeekComplete }
hde: irq timeout: status=0x50 { DriveReady SeekComplete }
hde: irq timeout: status=0x50 { DriveReady SeekComplete }
ide2: reset: master: error (0x00?)
hde: irq timeout: status=0x50 { DriveReady SeekComplete }
hde: irq timeout: status=0x50 { DriveReady SeekComplete }
hde: irq timeout: status=0x50 { DriveReady SeekComplete }
hde: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
ide2(?): unexpected interrupt, status=0x58, count=1
ide2: reset: master: error (0x00?)
hde: status error: status=0x58 { DriveReady SeekComplete DataRequest }
end_request: I/O error, dev 21:00 (hde), sector 0
hde: drive not ready for command
unable to read partition table
hdf:hdf: irq timeout: status=0x50 { DriveReady SeekComplete }
hdf: irq timeout: status=0x50 { DriveReady SeekComplete }
hdf: irq timeout: status=0x50 { DriveReady SeekComplete }
hdf: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
ide2(?): unexpected interrupt, status=0x58, count=2
ide2: reset: master: error (0x00?)
hdf: status error: status=0x58 { DriveReady SeekComplete DataRequest }
hdf: drive not ready for command
hdf: irq timeout: status=0x50 { DriveReady SeekComplete }
hdf: irq timeout: status=0x50 { DriveReady SeekComplete }
hdf: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
ide2(?): unexpected interrupt, status=0x58, count=3
ide2: reset: master: error (0x00?)
hdf: status error: status=0x58 { DriveReady SeekComplete DataRequest }
end_request: I/O error, dev 21:40 (hdf), sector 0
hdf: drive not ready for command
unable to read partition table
...
(similar for hdg ... hdh ...)
...
Thanks,
Andy Galasso
andy@adgsoftware.com
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
reply other threads:[~2001-01-01 22:34 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20010101170741.A14537@adgsoftware.com \
--to=andy@adgsoftware.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.