From: Vojtech Pavlik <vojtech@suse.cz>
To: Tkil <tkil@scrye.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>, linux-kernel@vger.kernel.org
Subject: Re: ide.2.4.1-p3.01112001.patch
Date: Sat, 13 Jan 2001 14:44:10 +0100 [thread overview]
Message-ID: <20010113144410.C1155@suse.cz> (raw)
In-Reply-To: <20010112204626.A2740@suse.cz> <E14HDqv-0005Fm-00@the-village.bc.nu> <14943.50581.978539.26089@slinky.scrye.com>
In-Reply-To: <14943.50581.978539.26089@slinky.scrye.com>; from tkil@scrye.com on Fri, Jan 12, 2001 at 08:03:49PM -0700
Hi!
I think that with 2.4.0 your board will operate just fine at UDMA33. If
you can, please do test that. Best mount your drives read only at first,
but I doubt there will be any problems.
Vojtech
On Fri, Jan 12, 2001 at 08:03:49PM -0700, Tkil wrote:
>
> Alan asked:
> > I think its significant that two reports I have are FIC PA-2013 but
> > not all. What combination of chips is on the 2013 ?
>
> My board here is a FIC PA-2013A (if I recall correctly; the
> motherboard only has "PA-2013" on it, no "A") rev 1.1.
>
> It's worth noting that there is at least another full revision level
> (2.x), and the BIOSes for these different revisions are *not*
> compatible (as I found out to my chagrin ;-).
>
> Also, the FIC PA-513 (maybe 512?) should be a very similar board, only
> wired for an AT power supply where the PA-2013 is an ATX board.
>
> I've never seen the DMA data corruption on this box, but I'd really
> really like to get something better than 3MB/s off my UDMA/66-capable
> drives. I'm pretty sure that (prior to the 2.2.18 squelching of all
> VIA IDE UDMA) that hda and hdc would come up with DMA enabled, at the
> very least. Is there a safe way to test various hdparm settings? I'm
> even willing to buy a scratch disk if that would help...
>
> Looking at the chips, I have:
>
> 1. VIA
> VT82C598MVP
> 9828CE Taiwan
> 13G003900
>
> 2. VIA
> VT82C586B
> S7-SB
> 9826CD Taiwan
> 14B013511
>
> It has an Award BIOS with a variety of WinBond support chips (looks
> like at least 4 on-board cache chips, and one near the BIOS EEPROM).
>
> Here's the relevant dmesg bits:
>
> | PCI: PCI BIOS revision 2.10 entry at 0xfb490
> | PCI: Using configuration type 1
> | PCI: Probing PCI hardware
> | PCI: 00:38 [1106/0586]: Work around ISA DMA hangs (00)
> | Activating ISA DMA hang workarounds.
> | Detected PS/2 Mouse Port.
> | Serial driver version 4.27 with no serial options enabled
> | ttyS00 at 0x03f8 (irq = 4) is a 16550A
> | ttyS01 at 0x02f8 (irq = 3) is a 16550A
> | Real Time Clock Driver v1.09
> | VP_IDE: IDE controller on PCI bus 00 dev 39
> | VP_IDE: not 100% native mode: will probe irqs later
> | ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
> | ide0: VIA Bus-Master (U)DMA Timing Config Success
> | ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
> | ide1: VIA Bus-Master (U)DMA Timing Config Success
> | hda: WDC WD307AA, ATA DISK drive
> | hdc: Maxtor 96147H8, ATA DISK drive
> | ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> | ide1 at 0x170-0x177,0x376 on irq 15
> | hda: WDC WD307AA, 29333MB w/2048kB Cache, CHS=59598/16/63
> | hdc: Maxtor 96147H8, 58623MB w/2048kB Cache, CHS=7473/255/63
> | Floppy drive(s): fd0 is 1.44M
> | FDC 0 is a post-1991 82077
> | Partition check:
> | sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
> | hda: [PTBL] [3739/255/63] hda1
> | hdc: hdc1
> | apm: BIOS version 1.2 Flags 0x07 (Driver version 1.13)
>
> Short version of lspci:
>
> | 00:00.0 Host bridge: VIA Technologies, Inc. VT82C597 [Apollo VP3] (rev 04)
> | 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
> | 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586 ISA [Apollo VP] (rev 41)
> | 00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06)
> | 00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 02)
> | 00:07.3 Bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
> | 00:08.0 SCSI storage controller: Symbios Logic Inc. (formerly NCR) 53c875 (rev 03)
> | 00:0a.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
> | 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 AGP [Millennium G200 AGP] (rev 01)
>
> I've included "hdparm" and "lspci -vvxxx" output below, omitting
> non-chipset related things (SCSI, Ethernet, and VGA). If it matters,
> this board is running 100MHz FSB with a 450MHz K6-3 CPU and 384MB (3 x
> 128MB DIMMs) of PC-100 SDRAM.
>
> If I can provide any more information, please don't hesitate to ask.
>
> Thanks,
> t.
>
> hdparm output:
>
> | # for i in hda hdc ; do hdparm /dev/$i ; hdparm -i /dev/$i ; done
> |
> | /dev/hda:
> | multcount = 0 (off)
> | I/O support = 0 (default 16-bit)
> | unmaskirq = 0 (off)
> | using_dma = 0 (off)
> | keepsettings = 0 (off)
> | nowerr = 0 (off)
> | readonly = 0 (off)
> | readahead = 8 (on)
> | geometry = 3739/255/63, sectors = 60074784, start = 0
> |
> | /dev/hda:
> |
> | Model=WDC WD307AA, FwRev=05.05B05, SerialNo=WD-WMA11
> | Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
> | RawCHS=16383/16/63, TrkSize=57600, SectSize=600, ECCbytes=40
> | BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=off
> | DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=0(slow)
> | CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=60074784
> | tDMA={min:120,rec:120}, DMA modes: mword0 mword1 *mword2
> | IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
> |
> |
> | /dev/hdc:
> | multcount = 0 (off)
> | I/O support = 0 (default 16-bit)
> | unmaskirq = 0 (off)
> | using_dma = 0 (off)
> | keepsettings = 0 (off)
> | nowerr = 0 (off)
> | readonly = 0 (off)
> | readahead = 8 (on)
> | geometry = 7473/255/63, sectors = 120060864, start = 0
> |
> | /dev/hdc:
> |
> | Model=Maxtor 96147H8, FwRev=BAC51KJ0, SerialNo=N80CP5KC
> | Config={ Fixed }
> | RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=57
> | BuffType=3(DualPortCache), BuffSize=2048kB, MaxMultSect=16, MultSect=off
> | DblWordIO=no, maxPIO=2(fast), DMA=yes, maxDMA=0(slow)
> | CurCHS=16383/16/63, CurSects=-66060037, LBA=yes, LBAsects=120060864
> | tDMA={min:120,rec:120}, DMA modes: mword0 mword1 *mword2
> | IORDY=on/off, tPIO={min:120,w/IORDY:120}, PIO modes: mode3 mode4
>
> lspci -vvxxx output:
>
> | 00:00.0 Host bridge: VIA Technologies, Inc. VT82C597 [Apollo VP3] (rev 04)
> | Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> | Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> | Latency: 16 set
> | Region 0: Memory at e0000000 (32-bit, prefetchable)
> | Capabilities: [a0] AGP version 1.0
> | Status: RQ=7 SBA+ 64bit- FW- Rate=1
> | Command: RQ=7 SBA+ AGP- 64bit- FW- Rate=1
> | 00: 06 11 97 05 06 00 90 02 04 00 00 06 00 10 00 00
> | 10: 08 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
> | 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
> | 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 50: 80 0a 05 40 00 00 00 00 98 80 10 10 20 20 28 30
> | 60: 3f 2a 00 23 e4 e4 e4 00 01 00 50 00 60 67 00 00
> | 70: e1 0a 6c 00 00 80 40 00 00 00 00 00 00 00 00 40
> | 80: 00 00 00 00 c0 00 00 00 02 00 00 00 00 00 00 00
> | 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | a0: 02 00 10 00 01 02 00 07 00 00 00 00 0a 00 00 00
> | b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | f0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 97 05
> |
> | 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
> | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> | Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
> | Latency: 0 set
> | Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> | I/O behind bridge: 0000d000-0000dfff
> | Memory behind bridge: e4000000-e7ffffff
> | Prefetchable memory behind bridge: e8000000-e8ffffff
> | BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
> | 00: 06 11 98 85 07 00 20 22 00 00 04 06 00 00 01 00
> | 10: 00 00 00 00 00 00 00 00 00 01 01 00 d0 d0 00 00
> | 20: 00 e4 f0 e7 00 e8 f0 e8 00 00 00 00 00 00 00 00
> | 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0c 00
> | 40: f0 ec 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> |
> | 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586 ISA [Apollo VP] (rev 41)
> | Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
> | Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> | Latency: 0 set
> | 00: 06 11 86 05 8f 00 00 02 41 00 01 06 00 00 80 00
> | 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 40: 00 05 00 00 01 00 10 a0 21 00 c4 00 00 00 00 f3
> | 50: 24 00 00 00 00 00 a0 90 00 06 f7 00 10 00 00 00
> | 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> |
> | 00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06) (prog-if 8a)
> | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> | Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> | Latency: 64 set
> | Region 4: I/O ports at e000
> | 00: 06 11 71 05 07 00 80 02 06 8a 01 01 00 40 00 00
> | 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 20: 01 e0 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 40: 0b f2 09 3a 69 00 f0 00 a8 a8 a8 a8 ff 00 ff ff
> | 50: 03 03 03 03 00 00 00 00 a8 a8 a8 a8 00 00 00 00
> | 60: 00 02 00 00 00 00 00 00 00 02 00 00 00 00 00 00
> | 70: 22 00 00 00 00 00 00 00 42 00 00 00 00 00 00 00
> | 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | d0: 06 00 71 05 00 00 00 00 00 00 00 00 00 00 00 00
> | e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> |
> | 00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 02)
> | Subsystem: Unknown device 0925:1234
> | Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> | Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> | Latency: 64 set, cache line size 08
> | Interrupt: pin D routed to IRQ 9
> | Region 4: I/O ports at e400
> | 00: 06 11 38 30 07 00 00 02 02 00 03 0c 08 40 00 00
> | 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 20: 01 e4 00 00 00 00 00 00 00 00 00 00 25 09 34 12
> | 30: 00 00 00 00 00 00 00 00 00 00 00 00 09 04 00 00
> | 40: 00 00 00 00 c6 00 11 18 00 00 00 00 00 00 00 00
> | 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 60: 10 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | c0: 00 20 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> |
> | 00:07.3 Bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
> | Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> | Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> | 00: 06 11 40 30 00 00 80 02 10 00 80 06 00 00 00 00
> | 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 40: 40 88 09 00 78 38 00 00 01 60 00 00 00 00 00 00
> | 50: 00 7c ee 88 00 00 00 00 00 00 00 00 00 00 00 00
> | 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> | f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
--
Vojtech Pavlik
SuSE Labs
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to majordomo@vger.kernel.org
Please read the FAQ at http://www.tux.org/lkml/
next prev parent reply other threads:[~2001-01-13 14:05 UTC|newest]
Thread overview: 60+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-01-12 8:44 ide.2.4.1-p3.01112001.patch Andre Hedrick
2001-01-12 8:55 ` ide.2.4.1-p3.01112001.patch Andre Hedrick
2001-01-12 17:51 ` ide.2.4.1-p3.01112001.patch Linus Torvalds
2001-01-12 18:13 ` ide.2.4.1-p3.01112001.patch Alan Cox
2001-01-12 18:37 ` ide.2.4.1-p3.01112001.patch Linus Torvalds
2001-01-12 21:26 ` ide.2.4.1-p3.01112001.patch Adrian Bunk
2001-01-12 18:17 ` ide.2.4.1-p3.01112001.patch Andre Hedrick
2001-01-12 18:55 ` ide.2.4.1-p3.01112001.patch Linus Torvalds
2001-01-12 19:46 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-12 19:57 ` ide.2.4.1-p3.01112001.patch Linus Torvalds
2001-01-12 20:24 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-12 23:47 ` ide.2.4.1-p3.01112001.patch Alan Cox
2001-01-13 13:45 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-13 17:09 ` ide.2.4.1-p3.01112001.patch Bryan O'Sullivan
2001-01-13 17:19 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-13 0:09 ` ide.2.4.1-p3.01112001.patch Linus Torvalds
2001-01-13 0:25 ` ide.2.4.1-p3.01112001.patch Alan Cox
2001-01-12 16:43 ` ide.2.4.1-p3.01112001.patch John Heil
2001-01-13 0:52 ` ide.2.4.1-p3.01112001.patch Linus Torvalds
2001-01-12 17:09 ` ide.2.4.1-p3.01112001.patch John Heil
2001-01-13 1:16 ` ide.2.4.1-p3.01112001.patch Linus Torvalds
2001-01-15 10:15 ` ide.2.4.1-p3.01112001.patch Matthias Andree
2001-01-13 1:12 ` ide.2.4.1-p3.01112001.patch Andre Hedrick
2001-01-13 1:18 ` ide.2.4.1-p3.01112001.patch Linus Torvalds
2001-01-13 1:24 ` ide.2.4.1-p3.01112001.patch Andre Hedrick
2001-01-13 1:31 ` ide.2.4.1-p3.01112001.patch Linus Torvalds
2001-01-13 1:48 ` ide.2.4.1-p3.01112001.patch Andre Hedrick
2001-01-13 1:51 ` ide.2.4.1-p3.01112001.patch Andre Hedrick
2001-01-13 14:02 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-13 14:00 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-13 19:46 ` ide.2.4.1-p3.01112001.patch Alan Cox
2001-01-13 20:00 ` ide.2.4.1-p3.01112001.patch Andre Hedrick
2001-01-14 3:41 ` ide.2.4.1-p3.01112001.patch TimO
2001-01-14 8:55 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-15 13:06 ` ide.2.4.1-p3.01112001.patch Stephen Clark
[not found] ` <Pine.LNX.4.30.0101130559060.19743-100000@wr5z.localdomain>
2001-01-13 14:22 ` VIA IDE corruption - anyone experiencing it with 2.4.0? Vojtech Pavlik
2001-01-12 23:43 ` ide.2.4.1-p3.01112001.patch Alan Cox
2001-01-13 2:43 ` ide.2.4.1-p3.01112001.patch davej
2001-01-13 13:42 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-13 3:03 ` ide.2.4.1-p3.01112001.patch Tkil
2001-01-13 13:44 ` Vojtech Pavlik [this message]
2001-01-13 13:35 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-14 19:38 ` ide.2.4.1-p3.01112001.patch Jamie Lokier
2001-01-14 22:39 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-15 0:06 ` ide.2.4.1-p3.01112001.patch Albert Cranford
2001-01-15 23:47 ` ide.2.4.1-p3.01112001.patch Henrique de Moraes Holschuh
2001-01-15 1:13 ` ide.2.4.1-p3.01112001.patch Jamie Lokier
2001-01-13 22:06 ` ide.2.4.1-p3.01112001.patch junio
2001-01-13 7:12 ` ide.2.4.1-p3.01112001.patch Andre Hedrick
2001-01-13 16:42 ` ide.2.4.1-p3.01112001.patch David Woodhouse
2001-01-13 17:04 ` ide.2.4.1-p3.01112001.patch Linus Torvalds
2001-01-14 17:22 ` ide.2.4.1-p3.01112001.patch David Woodhouse
2001-01-13 18:54 ` ide.2.4.1-p3.01112001.patch Russell King
2001-01-12 8:56 ` ide.2.4.1-p3.01112001.patch Craig Schlenter
-- strict thread matches above, loose matches on Subject: below --
2001-01-13 23:40 ide.2.4.1-p3.01112001.patch Andrzej Krzysztofowicz
2001-01-14 8:46 ` ide.2.4.1-p3.01112001.patch Vojtech Pavlik
2001-01-14 3:53 ide.2.4.1-p3.01112001.patch Tony Parsons
2001-01-14 8:31 ` ide.2.4.1-p3.01112001.patch David D.W. Downey
2001-01-14 9:03 ` ide.2.4.1-p3.01112001.patch David D.W. Downey
2001-01-15 10:29 ` ide.2.4.1-p3.01112001.patch Paul Flinders
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20010113144410.C1155@suse.cz \
--to=vojtech@suse.cz \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=linux-kernel@vger.kernel.org \
--cc=tkil@scrye.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.