From: "John L. Korpi" <jkorpi@mindspring.com>
To: mcuss@cdlsystems.com, "Linux-Kernel ML" <linux-kernel@vger.kernel.org>
Subject: Re: DMA Problems with Intel 845 Chipset and Northwood CPU
Date: Wed, 7 Aug 2002 20:58:54 -0400 [thread overview]
Message-ID: <200208072058.54512.jkorpi@mindspring.com> (raw)
In-Reply-To: <048001c23e6b$20e1ffe0$2c0e10ac@frinkiac7>
Had a similar problem with similar chipsets. 2.4.19-ac4 fixed the problem.
Cheers
jlk
On Wednesday 07 August 2002 07:35 pm, Mark Cuss wrote:
> Hello all,
>
> Please accept my apologies if this question has already been answered....
>
> I have a new Pentium 4 computer and I can't get the DMA working for hard
> disk transfers. Specifically, its a Dell Dimension 4500 with a Pentium 4
> 2.26 GHz processor (Northwood) and an 845 (Brookdale) chipset. RedHat
> 7.3....
>
> I noticed that the hard disk transfers were very slow. I tried to set up
> DMA with hdparm - see below:
>
> [root@yoda ide]# hdparm /dev/hda
>
> /dev/hda:
> multcount = 16 (on)
> I/O support = 0 (default 16-bit)
> unmaskirq = 0 (off)
> using_dma = 0 (off)
> keepsettings = 0 (off)
> nowerr = 0 (off)
> readonly = 0 (off)
> readahead = 8 (on)
> geometry = 4866/255/63, sectors = 78177792, start = 0
> busstate = 1 (on)
> [root@yoda ide]# hdparm -d1 /dev/hda
>
> /dev/hda:
> setting using_dma to 1 (on)
> HDIO_SET_DMA failed: Operation not permitted
> using_dma = 0 (off)
> [root@yoda ide]#
>
> I thought that perhaps the chipset had changed between this Northwood
> machine an the older core - I have a P4 1.8 GHz machine that DMA works fine
> on. I upgraded to kernel 2.4.19 with no change.
>
> The IDE controller (according to Windows XP....) is an Intel 82801DB Ultra
> ATA Storage Controller - 24CB. I've included the lspci --vvx listing from
> the problem machine below - my aplogies for the long list. If anyone has
> any suggestions I'd really appreciate them...
>
> Thanks....
>
> Mark
>
> lspci listing:
>
> 00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge
> (rev 11)
> Subsystem: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort+ >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
> Capabilities: [e4] #09 [a104]
> Capabilities: [a0] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
> Command: RQ=0 SBA- AGP+ 64bit- FW- Rate=<none>
> 00: 86 80 30 1a 06 01 90 20 11 00 00 06 00 00 00 00
> 10: 08 00 00 f0 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 30 1a
> 30: 00 00 00 00 e4 00 00 00 00 00 00 00 00 00 00 00
>
> 00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge
> (rev 11) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
> Memory behind bridge: fc700000-fe7fffff
> Prefetchable memory behind bridge: dc300000-ec4fffff
> BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
> 00: 86 80 31 1a 07 01 a0 00 11 00 04 06 00 40 01 00
> 10: 00 00 00 00 00 00 00 00 00 01 01 40 f0 00 a0 22
> 20: 70 fc 70 fe 30 dc 40 ec 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0a 00
>
> 00:1d.0 USB Controller: Intel Corp.: Unknown device 24c2 (rev 01) (prog-if
> 00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 11
> Region 4: I/O ports at e800 [size=32]
> 00: 86 80 c2 24 05 00 80 02 01 00 03 0c 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 01 e8 00 00 00 00 00 00 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
>
> 00:1d.1 USB Controller: Intel Corp.: Unknown device 24c4 (rev 01) (prog-if
> 00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin B routed to IRQ 5
> Region 4: I/O ports at e880 [size=32]
> 00: 86 80 c4 24 05 00 80 02 01 00 03 0c 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 81 e8 00 00 00 00 00 00 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 05 02 00 00
>
> 00:1d.2 USB Controller: Intel Corp.: Unknown device 24c7 (rev 01) (prog-if
> 00 [UHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin C routed to IRQ 9
> Region 4: I/O ports at ec00 [size=32]
> 00: 86 80 c7 24 05 00 80 02 01 00 03 0c 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 01 ec 00 00 00 00 00 00 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 09 03 00 00
>
> 00:1d.7 USB Controller: Intel Corp.: Unknown device 24cd (rev 01) (prog-if
> 20 [EHCI])
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin D routed to IRQ 10
> Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
> Capabilities: [50] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
> PME(D0+,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [58] #0a [2080]
> 00: 86 80 cd 24 06 01 90 02 01 20 03 0c 00 00 00 00
> 10: 00 fc bf fe 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 50 00 00 00 00 00 00 00 0a 04 00 00
>
> 00:1e.0 PCI bridge: Intel Corp. 82801BA/CA PCI Bridge (rev 81) (prog-if 00
> [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
> <MAbort- >SERR- <PERR+
> Latency: 0
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: fe800000-feafffff
> Prefetchable memory behind bridge: ec500000-ec5fffff
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> 00: 86 80 4e 24 07 01 80 80 81 00 04 06 00 00 01 00
> 10: 00 00 00 00 00 00 00 00 00 02 02 20 d0 d0 80 22
> 20: 80 fe a0 fe 50 ec 50 ec 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 06 00
>
> 00:1f.0 ISA bridge: Intel Corp.: Unknown device 24c0 (rev 01)
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> 00: 86 80 c0 24 0f 01 80 02 01 00 01 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 00:1f.1 IDE interface: Intel Corp.: Unknown device 24cb (rev 01) (prog-if
> 8a [Master SecP PriP])
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 0
> Interrupt: pin A routed to IRQ 9
> Region 0: I/O ports at <unassigned> [size=8]
> Region 1: I/O ports at <unassigned> [size=4]
> Region 2: I/O ports at <unassigned> [size=8]
> Region 3: I/O ports at <unassigned> [size=4]
> Region 4: I/O ports at ffa0 [size=16]
> Region 5: Memory at 20000000 (32-bit, non-prefetchable) [disabled]
> [size=1K]
> 00: 86 80 cb 24 05 00 80 02 01 8a 01 01 00 00 00 00
> 10: 01 00 00 00 01 00 00 00 01 00 00 00 01 00 00 00
> 20: a1 ff 00 00 00 00 00 20 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 01 00 00
>
> 00:1f.3 SMBus: Intel Corp.: Unknown device 24c3 (rev 01)
> Subsystem: Dell Computer Corporation: Unknown device 0132
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Interrupt: pin B routed to IRQ 3
> Region 4: I/O ports at e480 [size=32]
> 00: 86 80 c3 24 01 00 80 02 01 00 05 0c 00 00 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 81 e4 00 00 00 00 00 00 00 00 00 00 28 10 32 01
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 03 02 00 00
>
> 01:00.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4
> Ti4200] (rev a3) (prog-if 00 [VGA])
> Subsystem: nVidia Corporation: Unknown device 0132
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 248 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M]
> Region 2: Memory at ec480000 (32-bit, prefetchable) [size=512K]
> Expansion ROM at fe7e0000 [disabled] [size=128K]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 2.0
> Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
> Command: RQ=31 SBA- AGP+ 64bit- FW- Rate=<none>
> 00: de 10 53 02 07 00 b0 02 a3 00 00 03 00 f8 00 00
> 10: 00 00 00 fd 08 00 00 e0 08 00 48 ec 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 32 01
> 30: 00 00 00 00 60 00 00 00 00 00 00 00 0b 01 05 01
>
> 02:00.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev
> 10)
> Subsystem: Intel Corp.: Unknown device 0071
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (2000ns min, 14000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at feaff000 (32-bit, non-prefetchable) [size=4K]
> Region 1: I/O ports at dc00 [size=64]
> Region 2: Memory at feac0000 (32-bit, non-prefetchable) [size=128K]
> Expansion ROM at feae0000 [disabled] [size=64K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> 00: 86 80 29 12 17 01 90 02 10 00 00 02 08 40 00 00
> 10: 00 f0 af fe 01 dc 00 00 00 00 ac fe 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 86 80 71 00
> 30: 00 00 ae fe dc 00 00 00 00 00 00 00 0b 01 08 38
>
> 02:02.0 Multimedia audio controller: Cirrus Logic CS 4614/22/24
> [CrystalClear SoundFusion Audio Accelerator] (rev 01)
> Subsystem: Voyetra Technologies: Unknown device 3357
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
> Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
> <MAbort- >SERR- <PERR-
> Latency: 64 (1000ns min, 6000ns max)
> Interrupt: pin A routed to IRQ 9
> Region 0: Memory at feafd000 (32-bit, non-prefetchable) [size=4K]
> Region 1: Memory at fe900000 (32-bit, non-prefetchable) [size=1M]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: 13 10 03 60 06 01 10 04 01 00 01 04 00 40 00 00
> 10: 00 d0 af fe 00 00 90 fe 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 53 50 57 33
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 09 01 04 18
>
>
> -
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
--
John L. Korpi, Ph.D. -- Senior Scientist, Networks & Infrastructure
NeuStar, Inc.
Voice: 1.216.241.2919, 1.703.435.0682
Mobile: 1.216.233.3042 Pager: 1.800.398.2959
next prev parent reply other threads:[~2002-08-08 0:55 UTC|newest]
Thread overview: 47+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-08-07 18:10 [patch] tls-2.5.30-A1 Ingo Molnar
2002-08-07 18:33 ` Linus Torvalds
2002-08-07 18:43 ` Stephen Rothwell
2002-08-07 18:57 ` Linus Torvalds
2002-08-07 19:40 ` Alexandre Julliard
2002-08-07 19:31 ` Ingo Molnar
2002-08-07 19:49 ` Alexandre Julliard
2002-08-07 22:01 ` Alan Cox
2002-08-07 22:36 ` Luca Barbieri
2002-08-07 22:54 ` Ingo Molnar
2002-08-07 23:21 ` Luca Barbieri
2002-08-07 23:35 ` DMA Problems with Intel 845 Chipset and Northwood CPU Mark Cuss
2002-08-08 0:58 ` John L. Korpi [this message]
2002-08-08 16:12 ` Mark Cuss
2002-08-11 21:46 ` [patch] tls-2.5.31-C3 Ingo Molnar
2002-08-12 7:34 ` Stephen Rothwell
2002-08-12 10:07 ` Ingo Molnar
2002-08-12 8:23 ` Stephen Rothwell
2002-08-12 10:08 ` Alan Cox
2002-08-12 10:49 ` Ingo Molnar
2002-08-12 10:34 ` Alan Cox
2002-08-12 12:17 ` Ingo Molnar
2002-08-12 11:47 ` Alan Cox
2002-08-12 12:55 ` Ingo Molnar
2002-08-12 12:29 ` Alan Cox
2002-08-12 10:35 ` Alan Cox
2002-08-12 13:10 ` Kasper Dupont
2002-08-12 15:20 ` Ingo Molnar
2002-08-12 14:46 ` Stephen Rothwell
2002-08-12 12:18 ` Luca Barbieri
2002-08-12 15:12 ` Ingo Molnar
2002-08-12 13:43 ` Luca Barbieri
2002-08-12 15:57 ` Ingo Molnar
2002-08-12 14:17 ` Luca Barbieri
2002-08-12 15:53 ` [patch] tls-2.5.31-D3 Ingo Molnar
2002-08-12 16:13 ` [patch] tls-2.5.31-D4 Ingo Molnar
2002-08-12 14:32 ` Luca Barbieri
2002-08-12 17:06 ` [patch] tls-2.5.31-D5 Ingo Molnar
2002-08-12 15:21 ` Jakub Jelinek
2002-08-12 17:41 ` Ingo Molnar
2002-08-12 15:54 ` Luca Barbieri
2002-08-12 18:03 ` [patch] tls-2.5.31-D9 Ingo Molnar
2002-08-13 1:50 ` [patch] tls-2.5.31-D5 Alexandre Julliard
2002-08-12 17:24 ` [patch] tls-2.5.31-D7 Ingo Molnar
2002-08-12 15:45 ` Christoph Hellwig
2002-08-07 19:02 ` [patch] tls-2.5.30-A1 Christoph Hellwig
2002-08-08 12:25 ` Jamie Lokier
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200208072058.54512.jkorpi@mindspring.com \
--to=jkorpi@mindspring.com \
--cc=linux-kernel@vger.kernel.org \
--cc=mcuss@cdlsystems.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.