From: Steffen Moser <lists@steffen-moser.de>
To: linux-kernel@vger.kernel.org
Subject: Complete system freeze with "linux-2.4.19-ac4"
Date: Sun, 18 Aug 2002 18:01:26 +0200 [thread overview]
Message-ID: <20020818160126.GA1696@steffen-moser.de> (raw)
Hi,
enclosed you'll find a bug report. I would be very interested
whether someone is able to reproduce the crash.
Regards,
Steffen
[1.] One line summary of the problem:
Complete freeze of system after trying to read:
"/proc/ide/ide1/hdd/identify"
if "ide-cd" ("/dev/hdd" is my IDE CD-ROM) is not loaded.
[2.] Full description of the problem/report:
Yesterday I had a complete lockup of my workstation machine after
doing a:
"cat /proc/ide/ide1/hdd/identify"
accidentally. "/dev/hdd" is my IDE CD-ROM drive. The problem only
occurs when kernel module "ide-cd" is _not_inserted_.
I can reprduce the crash very easily and regularly by trying to read
from "/proc/ide/ide1/hdd/identify" whenever the "ide-cd"-module is not
loaded.
I don't get any kernel OOPS or PANIC message neither on the console
screen nor within my log files... The system just stops totally,
CAPS lock and SCROLL lock start blinking. SYSRQ-magic-keys don't
function either...
Some information about my machine:
| steffen@pc01:~> cat /proc/ide/via
| ----------VIA BusMastering IDE Configuration----------------
| Driver Version: 3.34
| South Bridge: VIA vt82c686a
| Revision: ISA 0x22 IDE 0x10
| Highest DMA rate: UDMA66
| BM-DMA base: 0xd000
| PCI clock: 33.3MHz
| Master Read Cycle IRDY: 0ws
| Master Write Cycle IRDY: 0ws
| BM IDE Status Register Read Retry: yes
| Max DRDY Pulse Width: No limit
| -----------------------Primary IDE-------Secondary IDE------
| Read DMA FIFO flush: yes yes
| End Sector FIFO flush: no no
| Prefetch Buffer: yes no
| Post Write Buffer: yes no
| Enabled: yes yes
| Simplex only: no no
| Cable Type: 80w 80w
| -------------------drive0----drive1----drive2----drive3-----
| Transfer Mode: UDMA PIO UDMA UDMA
| Address Setup: 30ns 120ns 30ns 30ns
| Cmd Active: 90ns 90ns 90ns 90ns
| Cmd Recovery: 30ns 30ns 30ns 30ns
| Data Active: 90ns 330ns 90ns 90ns
| Data Recovery: 30ns 270ns 30ns 30ns
| Cycle Time: 30ns 600ns 30ns 60ns
| Transfer Rate: 66.6MB/s 3.3MB/s 66.6MB/s 33.3MB/s
| steffen@pc01:~> cat /proc/ide/drivers
| ide-cdrom version 4.59
| ide-disk version 1.16
I tried to reproduce the crash on another machine running the same
kernel ("linux-2.4.19-ac4"). This machine has got also a VIA chip-
set and shows exactly the same symptom (= crash):
| gateway:~ # cat /proc/ide/via
| ----------VIA BusMastering IDE Configuration----------------
| Driver Version: 3.34
| South Bridge: VIA vt82c686b
| Revision: ISA 0x40 IDE 0x6
| Highest DMA rate: UDMA100
| BM-DMA base: 0xe000
| PCI clock: 33.3MHz
| Master Read Cycle IRDY: 0ws
| Master Write Cycle IRDY: 0ws
| BM IDE Status Register Read Retry: yes
| Max DRDY Pulse Width: No limit
| -----------------------Primary IDE-------Secondary IDE------
| Read DMA FIFO flush: yes yes
| End Sector FIFO flush: no no
| Prefetch Buffer: no no
| Post Write Buffer: no no
| Enabled: yes yes
| Simplex only: no no
| Cable Type: 80w 80w
| -------------------drive0----drive1----drive2----drive3-----
| Transfer Mode: UDMA PIO UDMA PIO
| Address Setup: 30ns 120ns 30ns 30ns
| Cmd Active: 90ns 90ns 90ns 90ns
| Cmd Recovery: 30ns 30ns 30ns 30ns
| Data Active: 90ns 330ns 90ns 90ns
| Data Recovery: 30ns 270ns 30ns 30ns
| Cycle Time: 20ns 600ns 20ns 120ns
| Transfer Rate: 99.9MB/s 3.3MB/s 99.9MB/s 16.6MB/s
| gateway:~ # cat /proc/ide/drivers
| ide-cdrom version 4.59
| ide-disk version 1.16
[3.] Keywords (i.e., modules, networking, kernel):
IDE subsystem, VIA chipset, modules (ide-cd.o)
[4.] Kernel version (from /proc/version):
Machine 1 ("pc01"):
Linux version 2.4.19-ac4 (root@pc01) (gcc version 2.95.3 20010315 (SuSE)) #52 Fri Aug 9 18:40:47 CEST 2002
Machine 2 ("gateway"):
Linux version 2.4.19-ac4 (root@gateway) (gcc version 2.95.3 20010315 (SuSE)) #10 Sun Aug 18 15:14:15 CEST 2002
[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt):
I'm sorry, I don't get any oops message. :-(
[6.] A small shell script or example program which triggers the
problem (if possible):
Just do a "rmmod ide-cd" (if it's inserted) and try to read from
"/proc/ide/ide1/hdd" (or whatever the file for your IDE CD-ROM drive
is).
[7.] Environment
[7.1.] Software (add the output of the ver_linux script here)
| pc01:/usr/src # ./linux-2.4.19-ac4/scripts/ver_linux
| If some fields are empty or look unusual you may have an old version.
| Compare to the current minimal requirements in Documentation/Changes.
|
| Linux pc01 2.4.19-ac4 #52 Fri Aug 9 18:40:47 CEST 2002 i686 unknown
|
| Gnu C 2.95.3
| Gnu make 3.79.1
| util-linux 2.11n
| mount 2.11n
| modutils 2.4.12
| e2fsprogs 1.26
| PPP 2.4.1
| isdn4k-utils 3.1pre4
| Linux C Library x 1 root root 1394238 Jul 12 17:29 /lib/libc.so.6
| Dynamic linker (ldd) 2.2.5
| Procps 2.0.7
| Net-tools 1.60
| Kbd 1.06
| Sh-utils 2.0
| Modules Loaded snd-pcm-oss snd-mixer-oss snd-seq-midi
| snd-seq-midi-event snd-seq snd-ens1371 snd-pcm snd-timer snd-rawmidi
| snd-seq-device snd-ac97-codec snd soundcore ipv6 mousedev hid input
| usb-uhci usbcore eepro100 hisax isdn slhc reiserfs ext3 jbd
| gateway:~ # /usr/src/linux-2.4.19-ac4/scripts/ver_linux
| If some fields are empty or look unusual you may have an old version.
| Compare to the current minimal requirements in Documentation/Changes.
|
| Linux gateway 2.4.19-ac4 #10 Sun Aug 18 15:14:15 CEST 2002 i686 unknown
|
| Gnu C 2.95.3
| Gnu make 3.79.1
| util-linux 2.11n
| mount 2.11n
| modutils 2.4.12
| e2fsprogs 1.26
| Linux C Library x 1 root root 1394238 Mar 23 19:34 /lib/libc.so.6
| Dynamic linker (ldd) 2.2.5
| Procps 2.0.7
| Net-tools 1.60
| Kbd 1.06
| Sh-utils 2.0
| Modules Loaded cdrom ipv6 3c59x
[7.2.] Processor information (from /proc/cpuinfo):
| pc01:/usr/src # cat /proc/cpuinfo
| processor : 0
| vendor_id : AuthenticAMD
| cpu family : 6
| model : 4
| model name : AMD Athlon(tm) processor
| stepping : 4
| cpu MHz : 1302.953
| cache size : 256 KB
| fdiv_bug : no
| hlt_bug : no
| f00f_bug : no
| coma_bug : no
| fpu : yes
| fpu_exception : yes
| cpuid level : 1
| wp : yes
| flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca
| cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow
| bogomips : 2595.22
| gateway:~ # cat /proc/cpuinfo
| processor : 0
| vendor_id : AuthenticAMD
| cpu family : 6
| model : 3
| model name : AMD Duron(tm) Processor
| stepping : 1
| cpu MHz : 800.062
| cache size : 64 KB
| fdiv_bug : no
| hlt_bug : no
| f00f_bug : no
| coma_bug : no
| fpu : yes
| fpu_exception : yes
| cpuid level : 1
| wp : yes
| flags : fpu vme de pse tsc msr pae mce cx8 sep mtrr pge mca
| cmov pat pse36 mmx fxsr syscall mmxext 3dnowext 3dnow
| bogomips : 1595.80
[7.3.] Module information (from /proc/modules):
| pc01:/usr/src # cat /proc/modules
| snd-pcm-oss 36128 1 (autoclean)
| snd-mixer-oss 9120 1 (autoclean)
| snd-seq-midi 3264 0 (unused)
| snd-seq-midi-event 2760 0 [snd-seq-midi]
| snd-seq 37036 0 [snd-seq-midi snd-seq-midi-event]
| snd-ens1371 9828 2
| snd-pcm 47872 0 [snd-pcm-oss snd-ens1371]
| snd-timer 10240 0 [snd-seq snd-pcm]
| snd-rawmidi 12192 0 [snd-seq-midi snd-ens1371]
| snd-seq-device 4076 0 [snd-seq-midi snd-seq snd-rawmidi]
| snd-ac97-codec 22692 0 [snd-ens1371]
| snd 24648 0 [snd-pcm-oss snd-mixer-oss snd-seq-midi
| snd-seq-midi-event snd-seq snd-ens1371 snd-pcm snd-timer snd-rawmidi
| snd-seq-device snd-ac97-codec]
| soundcore 3332 6 [snd]
| ipv6 127392 -1 (autoclean)
| mousedev 3872 1
| hid 19392 0 (unused)
| input 3168 0 [mousedev hid]
| usb-uhci 21508 0 (unused)
| usbcore 55552 1 [hid usb-uhci]
| eepro100 17584 1
| hisax 137152 1
| isdn 108576 2 [hisax]
| slhc 4624 0 [isdn]
| reiserfs 159008 1 (autoclean)
| ext3 57600 5 (autoclean)
| jbd 34800 5 (autoclean) [ext3]
| gateway:~ # cat /proc/modules
| cdrom 28736 0
| ipv6 127456 -1 (autoclean)
| 3c59x 25128 1
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
| pc01:/usr/src # cat /proc/ioports
| 0000-001f : dma1
| 0020-003f : pic1
| 0040-005f : timer
| 0060-006f : keyboard
| 0070-007f : rtc
| 0080-008f : dma page reg
| 00a0-00bf : pic2
| 00c0-00df : dma2
| 00f0-00ff : fpu
| 0170-0177 : ide1
| 01f0-01f7 : ide0
| 0376-0376 : ide1
| 03c0-03df : vesafb
| 03f6-03f6 : ide0
| 0cf8-0cff : PCI conf1
| 4000-40ff : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
| 5000-500f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
| 6000-607f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
| c000-cfff : PCI Bus #01
| c000-c0ff : ATI Technologies Inc Rage 128 RF/SG AGP
| d000-d00f : VIA Technologies, Inc. Bus Master IDE
| d000-d007 : ide0
| d008-d00f : ide1
| d400-d41f : VIA Technologies, Inc. UHCI USB
| d400-d41f : usb-uhci
| dc00-dc3f : Intel Corp. 82557/8/9 [Ethernet Pro 100]
| dc00-dc3f : eepro100
| e000-e01f : AVM Audiovisuelles MKTG & Computer System GmbH A1 ISDN [Fritz]
| e000-e01f : avm PCI
| e400-e4ff : Adaptec AHA-2940UW Pro / AIC-788x
| e800-e83f : Ensoniq 5880 AudioPCI
| e800-e83f : Ensoniq AudioPCI
| pc01:/usr/src # cat /proc/iomem
| 00000000-0009ffff : System RAM
| 000a0000-000bffff : Video RAM area
| 000c0000-000c7fff : Video ROM
| 000c8000-000c8fff : Extension ROM
| 000c9000-000c97ff : Extension ROM
| 000f0000-000fffff : System ROM
| 00100000-1ffeffff : System RAM
| 00100000-001e4f4f : Kernel code
| 001e4f50-00247c9f : Kernel data
| 1fff0000-1fff2fff : ACPI Non-volatile Storage
| 1fff3000-1fffffff : ACPI Tables
| d0000000-d7ffffff : VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
| d8000000-dbffffff : PCI Bus #01
| d8000000-dbffffff : ATI Technologies Inc Rage 128 RF/SG AGP
| d8000000-d9ffffff : vesafb
| dc000000-ddffffff : PCI Bus #01
| dd000000-dd003fff : ATI Technologies Inc Rage 128 RF/SG AGP
| df000000-df0fffff : Intel Corp. 82557/8/9 [Ethernet Pro 100]
| df100000-df100fff : Intel Corp. 82557/8/9 [Ethernet Pro 100]
| df100000-df100fff : eepro100
| df101000-df10101f : AVM Audiovisuelles MKTG & Computer System GmbH A1 ISDN [Fritz]
| df102000-df102fff : Adaptec AHA-2940UW Pro / AIC-788x
| ffff0000-ffffffff : reserved
| gateway:~ # cat /proc/ioports
| 0000-001f : dma1
| 0020-003f : pic1
| 0040-005f : timer
| 0060-006f : keyboard
| 0080-008f : dma page reg
| 00a0-00bf : pic2
| 00c0-00df : dma2
| 00f0-00ff : fpu
| 0170-0177 : ide1
| 01f0-01f7 : ide0
| 0376-0376 : ide1
| 03c0-03df : vga+
| 03f6-03f6 : ide0
| 0cf8-0cff : PCI conf1
| 5000-500f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
| 6000-607f : VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
| e000-e00f : VIA Technologies, Inc. Bus Master IDE
| e000-e007 : ide0
| e008-e00f : ide1
| e400-e41f : VIA Technologies, Inc. UHCI USB
| e800-e81f : VIA Technologies, Inc. UHCI USB (#2)
| ec00-ec7f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
| ec00-ec7f : 00:12.0
| gateway:~ # cat /proc/iomem
| 00000000-0009ffff : System RAM
| 000a0000-000bffff : Video RAM area
| 000c0000-000c7fff : Video ROM
| 000f0000-000fffff : System ROM
| 00100000-1ffeffff : System RAM
| 00100000-0022aceb : Kernel code
| 0022acec-0029b41f : Kernel data
| 1fff0000-1fff2fff : ACPI Non-volatile Storage
| 1fff3000-1fffffff : ACPI Tables
| d0000000-d3ffffff : VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
| d4000000-d5ffffff : PCI Bus #01
| d4000000-d5ffffff : nVidia Corporation Vanta [NV6]
| d6000000-d7ffffff : PCI Bus #01
| d6000000-d6ffffff : nVidia Corporation Vanta [NV6]
| d9000000-d900007f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
| ffff0000-ffffffff : reserved
[7.5.] PCI information ('lspci -vvv' as root)
| pc01:~ # lspci -vvv
| 00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 02)
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
| Latency: 8
| Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
| Capabilities: [a0] AGP version 2.0
| Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2
| Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
| Capabilities: [c0] Power Management version 2
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
| Latency: 0
| Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
| I/O behind bridge: 0000c000-0000cfff
| Memory behind bridge: dc000000-ddffffff
| Prefetchable memory behind bridge: d8000000-dbffffff
| BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
| Capabilities: [80] Power Management version 2
| Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
| Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 0
|
| 00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
| Subsystem: VIA Technologies, Inc. Bus Master IDE
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 32
| Region 4: I/O ports at d000 [size=16]
| Capabilities: [c0] Power Management version 2
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 10) (prog-if 00 [UHCI])
| Subsystem: Unknown device 0925:1234
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 32, cache line size 08
| Interrupt: pin D routed to IRQ 11
| Region 4: I/O ports at d400 [size=32]
| Capabilities: [80] Power Management version 2
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
| Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
| Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Interrupt: pin ? routed to IRQ 9
| Capabilities: [68] Power Management version 2
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:09.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
| Subsystem: Intel Corp. EtherExpress PRO/100+ Management Adapter
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 32 (2000ns min, 14000ns max), cache line size 08
| Interrupt: pin A routed to IRQ 10
| Region 0: Memory at df100000 (32-bit, non-prefetchable) [size=4K]
| Region 1: I/O ports at dc00 [size=64]
| Region 2: Memory at df000000 (32-bit, non-prefetchable) [size=1M]
| Expansion ROM at <unassigned> [disabled] [size=1M]
| Capabilities: [dc] Power Management version 2
| Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
| Status: D0 PME-Enable- DSel=0 DScale=2 PME-
|
| 00:0a.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH A1 ISDN [Fritz] (rev 02)
| Subsystem: AVM Audiovisuelles MKTG & Computer System GmbH FRITZ!Card ISDN Controller
| Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Interrupt: pin A routed to IRQ 12
| Region 0: Memory at df101000 (32-bit, non-prefetchable) [size=32]
| Region 1: I/O ports at e000 [size=32]
|
| 00:0b.0 SCSI storage controller: Adaptec AHA-2940UW Pro / AIC-788x (rev 01)
| Subsystem: Adaptec 2940UW Pro Ultra-Wide SCSI Controller
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 32 (2000ns min, 2000ns max), cache line size 08
| Interrupt: pin A routed to IRQ 11
| Region 0: I/O ports at e400 [size=256]
| Region 1: Memory at df102000 (32-bit, non-prefetchable) [size=4K]
| Expansion ROM at <unassigned> [disabled] [size=64K]
| Capabilities: [dc] Power Management version 1
| Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:0d.0 Multimedia audio controller: Ensoniq 5880 AudioPCI (rev 02)
| Subsystem: Ensoniq Creative Sound Blaster AudioPCI128
| Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort+ <MAbort+ >SERR- <PERR-
| Latency: 32 (3000ns min, 32000ns max)
| Interrupt: pin A routed to IRQ 11
| Region 0: I/O ports at e800 [size=64]
| Capabilities: [dc] Power Management version 1
| Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 01:00.0 VGA compatible controller: ATI Technologies Inc Rage 128 RF/SG AGP (prog-if 00 [VGA])
| Subsystem: ATI Technologies Inc Magnum/Xpert128/X99/Xpert2000
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
| Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 32 (2000ns min), cache line size 08
| Interrupt: pin A routed to IRQ 5
| Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
| Region 1: I/O ports at c000 [size=256]
| Region 2: Memory at dd000000 (32-bit, non-prefetchable) [size=16K]
| Expansion ROM at <unassigned> [disabled] [size=128K]
| Capabilities: [50] AGP version 2.0
| Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
| Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
| Capabilities: [5c] Power Management version 1
| Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
| gateway:~ # lspci -vvv
| 00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
| Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
| Latency: 0
| Region 0: Memory at d0000000 (32-bit, prefetchable) [size=64M]
| Capabilities: [a0] AGP version 2.0
| Status: RQ=31 SBA+ 64bit- FW- Rate=x1,x2
| Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
| Capabilities: [c0] Power Management version 2
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
| Latency: 0
| Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
| I/O behind bridge: 0000f000-00000fff
| Memory behind bridge: d6000000-d7ffffff
| Prefetchable memory behind bridge: d4000000-d5ffffff
| BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
| Capabilities: [80] Power Management version 2
| Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
| Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 0
| Capabilities: [c0] Power Management version 2
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
| Subsystem: VIA Technologies, Inc. Bus Master IDE
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 32
| Region 4: I/O ports at e000 [size=16]
| Capabilities: [c0] Power Management version 2
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
| Subsystem: Unknown device 0925:1234
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 32, cache line size 08
| Interrupt: pin D routed to IRQ 12
| Region 4: I/O ports at e400 [size=32]
| Capabilities: [80] Power Management version 2
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16) (prog-if 00 [UHCI])
| Subsystem: Unknown device 0925:1234
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 32, cache line size 08
| Interrupt: pin D routed to IRQ 12
| Region 4: I/O ports at e800 [size=32]
| Capabilities: [80] Power Management version 2
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
| Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
| Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Interrupt: pin ? routed to IRQ 5
| Capabilities: [68] Power Management version 2
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
|
| 00:12.0 Ethernet controller: 3Com Corporation 3c905C-TX [Fast Etherlink] (rev 74)
| Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 32 (2500ns min, 2500ns max), cache line size 08
| Interrupt: pin A routed to IRQ 11
| Region 0: I/O ports at ec00 [size=128]
| Region 1: Memory at d9000000 (32-bit, non-prefetchable) [size=128]
| Expansion ROM at <unassigned> [disabled] [size=128K]
| Capabilities: [dc] Power Management version 2
| Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
| Status: D0 PME-Enable+ DSel=0 DScale=2 PME-
|
| 01:00.0 VGA compatible controller: nVidia Corporation Vanta [NV6] (rev 15) (prog-if 00 [VGA])
| Subsystem: Elsa AG: Unknown device 0c3a
| Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
| Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
| Latency: 32 (1250ns min, 250ns max)
| Interrupt: pin A routed to IRQ 10
| Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=16M]
| Region 1: Memory at d4000000 (32-bit, prefetchable) [size=32M]
| Expansion ROM at <unassigned> [disabled] [size=64K]
| Capabilities: [60] Power Management version 1
| Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
| Status: D0 PME-Enable- DSel=0 DScale=0 PME-
| Capabilities: [44] AGP version 2.0
| Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2
| Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
[7.6.] SCSI information (from /proc/scsi/scsi)
SCSI subsystem was not active (on "pc01").
If I load the modules, I get:
| pc01:~ # cat /proc/scsi/scsi
| Attached devices:
| Host: scsi0 Channel: 00 Id: 03 Lun: 00
| Vendor: YAMAHA Model: CRW8424S Rev: 1.0j
| Type: CD-ROM ANSI SCSI revision: 02
| Host: scsi0 Channel: 00 Id: 06 Lun: 00
| Vendor: HP Model: HP35470A Rev: T603
| Type: Sequential-Access ANSI SCSI revision: 02
On "gateway" there is no SCSI hardware present.
next reply other threads:[~2002-08-18 15:57 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-08-18 16:01 Steffen Moser [this message]
2002-08-18 16:34 ` Complete system freeze with "linux-2.4.19-ac4" Robert Love
2002-08-18 21:03 ` Steffen Moser
2002-08-19 19:42 ` Steffen Moser
2002-08-18 21:10 ` Nuno Monteiro
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20020818160126.GA1696@steffen-moser.de \
--to=lists@steffen-moser.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.