From: Gerd Knorr <kraxel@bytesex.org>
To: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Martin Mares <mj@ucw.cz>, Kernel List <linux-kernel@vger.kernel.org>
Subject: Re: ignore pci devices?
Date: Wed, 11 Sep 2002 17:37:51 +0200 [thread overview]
Message-ID: <20020911153750.GA8649@bytesex.org> (raw)
In-Reply-To: <1031747880.2726.40.camel@irongate.swansea.linux.org.uk>
On Wed, Sep 11, 2002 at 01:38:00PM +0100, Alan Cox wrote:
>
> Up until 2.4.20pre6 they are broken in the PCI core. IDE found that one
> out.
>
> The reserve module is an interesting approach though. I had been
> pondering doing a rename module for some similar purposes but completely
> missed that one.
>
> BTW we have pci_request_resource stuff that would shrink your module a
> fair bit
guess you mean pci_assign_resource()? Played with that one, now my
/proc/iomem file looks *ahem* intresting. Is this the bug mentioned
above?
Gerd
==============================[ cut here ]==============================
Script started on Wed Sep 11 17:33:33 2002
bogomips kraxel ~/kernel/bttv-0.7.97/driver# lspci -vs a.0
00:0a.0 Multimedia video controller: Brooktree Corporation Bt878 (rev 11)
Subsystem: TERRATEC Electronic GmbH: Unknown device 1135
Flags: bus master, medium devsel, latency 32, IRQ 5
Memory at ce000000 (32-bit, prefetchable) [size=4K]
Capabilities: <available only to root>
bogomips kraxel ~/kernel/bttv-0.7.97/driver# insmod ./pci-reserve.o ignore=0a.0
bogomips kraxel ~/kernel/bttv-0.7.97/driver# dmesg | tail
lp0: using parport0 (polling).
nfs warning: mount version older than kernel
/dev/vmnet: open called by PID 1250 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 1267 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
vmnet8: no IPv6 routers present
reserve: ignore="0a.0" -> using device 00:0a.0
reserve: probe device 00:0a.0
reserve: ... ressource at 40000000 size 1000 [ok]
bogomips kraxel ~/kernel/bttv-0.7.97/driver# cat /proc/iomem
00000000-0009efff : System RAM
0009f000-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000c8000-000cb7ff : Extension ROM
000f0000-000fffff : System ROM
00100000-3fffbfff : System RAM
00100000-001ecc3c : Kernel code
001ecc3d-0024aa5f : Kernel data
3fffc000-3fffefff : ACPI Tables
3ffff000-3fffffff : ACPI Non-volatile Storage
40000000-40000fff : Brooktree Corporation Bt878 Video Capture
ca000000-ca0000ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
ca800000-ca8003ff : Philips Semiconductors SAA7134 (#2)
cb000000-cb0000ff : Lite-On Communications Inc LNE100TX
cb000000-cb0000ff : tulip
cb800000-cb8003ff : Philips Semiconductors SAA7134
cc000000-cd6fffff : PCI Bus #01
cc000000-cc7fffff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : matroxfb MMIO
cd800000-cd800fff : Brooktree Corporation Bt878 Audio Capture
40000000-40000fff : Brooktree Corporation Bt878 Video Capture
ca000000-ca0000ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
ca800000-ca8003ff : Philips Semiconductors SAA7134 (#2)
cb000000-cb0000ff : Lite-On Communications Inc LNE100TX
cb000000-cb0000ff : tulip
cb800000-cb8003ff : Philips Semiconductors SAA7134
cc000000-cd6fffff : PCI Bus #01
cc000000-cc7fffff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : matroxfb MMIO
cd800000-cd800fff : Brooktree Corporation Bt878 Audio Capture
40000000-40000fff : Brooktree Corporation Bt878 Video Capture
ca000000-ca0000ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
ca800000-ca8003ff : Philips Semiconductors SAA7134 (#2)
cb000000-cb0000ff : Lite-On Communications Inc LNE100TX
cb000000-cb0000ff : tulip
cb800000-cb8003ff : Philips Semiconductors SAA7134
cc000000-cd6fffff : PCI Bus #01
cc000000-cc7fffff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : matroxfb MMIO
cd800000-cd800fff : Brooktree Corporation Bt878 Audio Capture
40000000-40000fff : Brooktree Corporation Bt878 Video Capture
ca000000-ca0000ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
ca800000-ca8003ff : Philips Semiconductors SAA7134 (#2)
cb000000-cb0000ff : Lite-On Communications Inc LNE100TX
cb000000-cb0000ff : tulip
cb800000-cb8003ff : Philips Semiconductors SAA7134
cc000000-cd6fffff : PCI Bus #01
cc000000-cc7fffff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : matroxfb MMIO
cd800000-cd800fff : Brooktree Corporation Bt878 Audio Capture
40000000-40000fff : Brooktree Corporation Bt878 Video Capture
ca000000-ca0000ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
ca800000-ca8003ff : Philips Semiconductors SAA7134 (#2)
cb000000-cb0000ff : Lite-On Communications Inc LNE100TX
cb000000-cb0000ff : tulip
cb800000-cb8003ff : Philips Semiconductors SAA7134
cc000000-cd6fffff : PCI Bus #01
cc000000-cc7fffff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : matroxfb MMIO
cd800000-cd800fff : Brooktree Corporation Bt878 Audio Capture
40000000-40000fff : Brooktree Corporation Bt878 Video Capture
ca000000-ca0000ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
ca800000-ca8003ff : Philips Semiconductors SAA7134 (#2)
cb000000-cb0000ff : Lite-On Communications Inc LNE100TX
cb000000-cb0000ff : tulip
cb800000-cb8003ff : Philips Semiconductors SAA7134
cc000000-cd6fffff : PCI Bus #01
cc000000-cc7fffff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : Matrox Graphics, Inc. MGA G200 AGP
cc800000-cc803fff : matroxfb MMIO
cd800000-cd800fff : Brooktree Corporation Bt878 Audio Capture
40000000-40000fff : Brooktree Corporation Bt878 Video Capture
ca000000-ca0000ff : LSI Logic / Symbios Logic (formerly NCR) 53c810
ca800000-ca8003ff : Philips Semiconductors SAA7134 (#2)
cb000000-cb0000ff : Lite-On Communications Inc LNE100TX
cb000000-cb0000ff : tulip
bogomips kraxel ~/kernel/bttv-0.7.97/driver#
Script done on Wed Sep 11 17:34:56 2002
==============================[ cut here ]==============================
/*
* pci-reserve.c -- reserve pci device resources to make device \
* drivers *not* touch the card
*
* (c) 2002 Gerd Knorr <kraxel@bytesex.org>
*
*/
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/kernel.h>
MODULE_DESCRIPTION("reserve pci device resources to make device drivers *not* touch the card");
MODULE_AUTHOR("Gerd Knorr");
MODULE_LICENSE("GPL");
static char *ignore = "none";
static int bus = -1, slot = -1,function = -1;
MODULE_PARM(ignore,"s");
#ifndef MODULE
static int __init setup(char *str) { ignore = str; return 0; }
__setup("pci-reserve.ignore=", setup);
#endif
static int __devinit probe(struct pci_dev *dev,
const struct pci_device_id *id)
{
int i,rc;
if (bus != dev->bus->number ||
slot != PCI_SLOT(dev->devfn) ||
function != PCI_FUNC(dev->devfn))
return -EBUSY;
printk("reserve: probe device %02x:%02x.%x\n",
dev->bus->number,PCI_SLOT(dev->devfn),PCI_FUNC(dev->devfn));
for (i = 0;; i++) {
if (0 == pci_resource_start(dev,i))
break;
rc = pci_assign_resource(dev,i);
printk("reserve: ... ressource at %lx size %lx [%s]\n",
pci_resource_start(dev,i),
pci_resource_len(dev,i),
rc ? "failed" : "ok");
if (rc)
return -EBUSY;
}
return 0;
}
static struct pci_device_id pci_tbl[] __devinitdata = {
{
.vendor = PCI_ANY_ID,
.device = PCI_ANY_ID,
.subvendor = PCI_ANY_ID,
.subdevice = PCI_ANY_ID,
},
{ /* end of list */}
};
MODULE_DEVICE_TABLE(pci, pci_tbl);
static struct pci_driver pci_driver = {
.name = "reserve",
.id_table = pci_tbl,
.probe = probe,
};
static int parse(char *id, int *b, int *s, int *f)
{
if (3 == sscanf(id,"%x:%x.%x",b,s,f)) {
/* nothing */;
} else if (2 == sscanf(id,"%x.%x",s,f)) {
*b = 0;
} else if (2 == sscanf(id,"%x:%x",b,s)) {
*f= 0;
} else if (1 == sscanf(id,"%x",s)) {
*b = 0; *f= 0;
} else {
printk("reserve: can't parse \"%s\"\n",id);
return -1;
}
return 0;
}
static int do_init(void)
{
if (parse(ignore,&bus,&slot,&function) < 0)
return -EINVAL;
printk("reserve: ignore=\"%s\" -> using device %02x:%02x.%x\n",
ignore,bus,slot,function);
return pci_module_init(&pci_driver);
}
static void do_fini(void)
{
pci_unregister_driver(&pci_driver);
}
module_init(do_init);
module_exit(do_fini);
/*
* Local variables:
* c-basic-offset: 8
* End:
*/
next prev parent reply other threads:[~2002-09-11 15:50 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-09-10 13:47 ignore pci devices? Gerd Knorr
2002-09-10 14:27 ` Alan Cox
2002-09-11 10:51 ` Gerd Knorr
2002-09-11 11:47 ` Alan Cox
2002-09-11 11:48 ` Alan Cox
2002-09-11 12:33 ` Gerd Knorr
2002-09-10 16:30 ` Martin Mares
2002-09-10 18:42 ` Alan Cox
2002-09-10 18:41 ` Martin Mares
2002-09-10 20:15 ` Alan Cox
2002-09-11 12:20 ` Gerd Knorr
2002-09-11 12:38 ` Alan Cox
2002-09-11 15:37 ` Gerd Knorr [this message]
2002-09-11 16:17 ` Alan Cox
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20020911153750.GA8649@bytesex.org \
--to=kraxel@bytesex.org \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=linux-kernel@vger.kernel.org \
--cc=mj@ucw.cz \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.