From: merlin hughes <merlin@merlin.org>
To: linux-kernel@vger.kernel.org
Subject: kernel BUG at drivers/scsi/scsi_lib.c:819 with 2.5.44-ac5
Date: Wed, 30 Oct 2002 09:18:12 -0500 [thread overview]
Message-ID: <20021030141812.BF07786921@primary.mx.nitric.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 3789 bytes --]
Hi,
Tyan Tiger S2466-4M, 2xAthlon MP, Adaptec 29160, Adaptec 2940u2w,
software RAID 5, gcc 2.95.4. The core drives are on the 29160. Works
fine under 2.4.19.
2.5.44 panics during boot with SCSI problems; I didn't catch what the
error was.
2.5.44-ac5 boots but bugs after a few seconds.
Attached: config, syslog, lspci (under 2.4.19)
Oct 28 12:36:09 badb kernel: Incorrect number of segments after building list
Oct 28 12:36:09 badb kernel: counted 2, received 1
Oct 28 12:36:09 badb kernel: req nr_sec 8, cur_nr_sec 8
Oct 28 12:36:09 badb kernel: end_request: I/O error, dev 08:40, sector 6784528
Oct 28 12:36:09 badb kernel: raid5: Disk failure on scsi/host0/bus0/target4/lun0/part7, disabling device. Operation continuing on 4 devices
Oct 28 12:36:09 badb kernel: blk: request botched
Oct 28 12:36:09 badb kernel: ------------[ cut here ]------------
Oct 28 12:36:09 badb kernel: kernel BUG at drivers/scsi/scsi_lib.c:819!
Oct 28 12:36:09 badb kernel: invalid operand: 0000
Oct 28 12:36:09 badb kernel: mousedev hid nfs lockd sunrpc ohci-hcd usbcore parport_pc lp parport sg st sr_mod cdrom floppy iptable_filter ip_tables emu10k1 sound soundcore ac97_codec 3c59x rtc
Oct 28 12:36:09 badb kernel: CPU: 1
Oct 28 12:36:09 badb kernel: EIP: 0060:[scsi_init_io+279/304] Not tainted
Oct 28 12:36:09 badb kernel: EFLAGS: 00010286
Oct 28 12:36:09 badb kernel: EIP is at scsi_init_io+0x117/0x130
Oct 28 12:36:09 badb kernel: eax: f5bcda00 ebx: f5bcda00 ecx: 00000001 edx: f7f51580
Oct 28 12:36:09 badb kernel: esi: 00000002 edi: f7ed62c0 ebp: f78c9f90 esp: f78c9f60
Oct 28 12:36:09 badb kernel: ds: 0068 es: 0068 ss: 0068
Oct 28 12:36:09 badb kernel: Process raid5d (pid: 17, threadinfo=f78c8000 task=f7e0cd00)
Oct 28 12:36:09 badb kernel: Stack: f7ed62c0 f5bcda00 f7ef3400 c01aa8bb f5bcda00 f7ef34c8 f7ef3428 f7ea3680
Oct 28 12:36:09 badb kernel: f7f56800 f78c8000 c031fb20 c019d88e 00000001 c019eb5d f7ef3428 f7df434c
Oct 28 12:36:09 badb kernel: f78c9fb4 c019ed80 f7ef3428 f78c8000 f78c8000 f78c9fb4 f78c9fb4 c01d6abf
Oct 28 12:36:09 badb kernel: Call Trace:
Oct 28 12:36:09 badb kernel: [scsi_request_fn+779/1136] scsi_request_fn+0x30b/0x470
Oct 28 12:36:09 badb kernel: [elv_queue_empty+14/32] elv_queue_empty+0xe/0x20
Oct 28 12:36:09 badb kernel: [generic_unplug_device+141/192] generic_unplug_device+0x8d/0xc0
Oct 28 12:36:09 badb kernel: [blk_run_queues+176/192] blk_run_queues+0xb0/0xc0
Oct 28 12:36:09 badb kernel: [md_thread+415/528] md_thread+0x19f/0x210
Oct 28 12:36:09 badb kernel: [md_thread+0/528] md_thread+0x0/0x210
Oct 28 12:36:09 badb kernel: [default_wake_function+0/64] default_wake_function+0x0/0x40
Oct 28 12:36:09 badb kernel: [kernel_thread_helper+5/24] kernel_thread_helper+0x5/0x18
Oct 28 12:36:09 badb kernel:
Oct 28 12:36:09 badb kernel: Code: 0f 0b 33 03 42 b0 24 c0 90 31 c0 5b 5e 5f c3 8d 76 00 8d bc
Oct 28 12:36:09 badb kernel: <6>md: updating md2 RAID superblock on device
Oct 28 12:36:09 badb kernel: md: (skipping faulty scsi/host0/bus0/target4/lun0/part7 )
Oct 28 12:36:09 badb kernel: md: scsi/host0/bus0/target3/lun0/part7 [events: 000000ac]<6>(write) scsi/host0/bus0/target3/lun0/part7's sb offset: 4200896
Oct 28 12:36:09 badb kernel: md: scsi/host0/bus0/target2/lun0/part7 [events: 000000ac]<6>(write) scsi/host0/bus0/target2/lun0/part7's sb offset: 4200896
Oct 28 12:36:09 badb kernel: md: scsi/host0/bus0/target1/lun0/part7 [events: 000000ac]<6>(write) scsi/host0/bus0/target1/lun0/part7's sb offset: 4200896
Oct 28 12:36:09 badb kernel: md: scsi/host0/bus0/target0/lun0/part7 [events: 000000ac]<6>(write) scsi/host0/bus0/target0/lun0/part7's sb offset: 4200896
I trust that the 'disk failure' is just a side-effect of the bug; the
system runs fine on 2.4.19 after I raidhotadd it back.
merlin
[-- Attachment #2: config-2.5.44-ac5 --]
[-- Type: text/plain, Size: 26111 bytes --]
#
# Automatically generated make config: don't edit
#
CONFIG_X86=y
CONFIG_MMU=y
CONFIG_SWAP=y
# CONFIG_SBUS is not set
CONFIG_UID16=y
CONFIG_GENERIC_ISA_DMA=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# General setup
#
CONFIG_NET=y
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
# CONFIG_M586 is not set
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
CONFIG_MK7=y
# CONFIG_MELAN is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_GEODE is not set
# CONFIG_MCYRIXIII is not set
# CONFIG_X86_HAVE_CMOV is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_HAS_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_HAVE_CMOV=y
# CONFIG_HUGETLB_PAGE is not set
CONFIG_SMP=y
CONFIG_PREEMPT=y
CONFIG_NR_CPUS=2
# CONFIG_X86_NUMA is not set
# CONFIG_X86_MCE is not set
# CONFIG_X86_MCE_NONFATAL is not set
# CONFIG_X86_MCE_P4THERMAL is not set
# CONFIG_CPU_FREQ is not set
# CONFIG_TOSHIBA is not set
# CONFIG_I8K is not set
# CONFIG_MICROCODE is not set
CONFIG_X86_MSR=m
# CONFIG_X86_CPUID is not set
# CONFIG_EDD is not set
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
CONFIG_HAVE_DEC_LOCK=y
#
# Power management options (ACPI, APM)
#
#
# ACPI Support
#
# CONFIG_ACPI is not set
# CONFIG_PM is not set
# CONFIG_APM is not set
#
# Bus options (PCI, PCMCIA, EISA, MCA, ISA)
#
# CONFIG_MCA is not set
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
# CONFIG_SCx200 is not set
CONFIG_PCI_NAMES=y
# CONFIG_ISA is not set
# CONFIG_EISA is not set
CONFIG_HOTPLUG=y
#
# PCMCIA/CardBus support
#
CONFIG_PCMCIA=m
CONFIG_CARDBUS=y
# CONFIG_I82092 is not set
CONFIG_I82365=m
# CONFIG_TCIC is not set
#
# PCI Hotplug Support
#
# CONFIG_HOTPLUG_PCI is not set
# CONFIG_HOTPLUG_PCI_COMPAQ is not set
# CONFIG_HOTPLUG_PCI_COMPAQ_NVRAM is not set
# CONFIG_HOTPLUG_PCI_IBM is not set
#
# Executable file formats
#
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
# CONFIG_PARPORT_SERIAL is not set
# CONFIG_PARPORT_PC_FIFO is not set
# CONFIG_PARPORT_PC_SUPERIO is not set
# CONFIG_PARPORT_PC_PCMCIA is not set
# CONFIG_PARPORT_AMIGA is not set
# CONFIG_PARPORT_MFC3 is not set
# CONFIG_PARPORT_ATARI is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_SUNBPP is not set
# CONFIG_PARPORT_OTHER is not set
CONFIG_PARPORT_1284=y
#
# Plug and Play configuration
#
# CONFIG_PNP is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_CISS_SCSI_TAPE is not set
# CONFIG_BLK_DEV_DAC960 is not set
# CONFIG_BLK_DEV_UMEM is not set
CONFIG_BLK_DEV_LOOP=m
# CONFIG_BLK_DEV_NBD is not set
# CONFIG_BLK_DEV_RAM is not set
# CONFIG_BLK_DEV_INITRD is not set
# CONFIG_LBD is not set
#
# ATA/ATAPI/MFM/RLL device support
#
# CONFIG_IDE is not set
# CONFIG_BLK_DEV_HD is not set
#
# SCSI device support
#
CONFIG_SCSI=y
#
# SCSI support type (disk, tape, CD-ROM)
#
CONFIG_BLK_DEV_SD=y
CONFIG_SD_EXTRA_DEVS=40
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
# CONFIG_BLK_DEV_SR_VENDOR is not set
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=m
#
# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
#
# CONFIG_SCSI_MULTI_LUN is not set
# CONFIG_SCSI_REPORT_LUNS is not set
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AACRAID is not set
CONFIG_SCSI_AIC7XXX=y
CONFIG_AIC7XXX_CMDS_PER_DEVICE=253
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
# CONFIG_AIC7XXX_BUILD_FIRMWARE is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
# CONFIG_SCSI_EATA is not set
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_GENERIC_NCR5380_MMIO is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_SYM53C8XX_2 is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_NSP32 is not set
# CONFIG_SCSI_DEBUG is not set
#
# PCMCIA SCSI adapter support
#
# CONFIG_SCSI_PCMCIA is not set
#
# Multi-device support (RAID and LVM)
#
CONFIG_MD=y
CONFIG_BLK_DEV_MD=y
# CONFIG_MD_LINEAR is not set
CONFIG_MD_RAID0=y
CONFIG_MD_RAID1=y
CONFIG_MD_RAID5=y
# CONFIG_MD_MULTIPATH is not set
# CONFIG_BLK_DEV_LVM is not set
# CONFIG_BLK_DEV_DM is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_BOOT is not set
# CONFIG_FUSION_ISENSE is not set
# CONFIG_FUSION_CTL is not set
# CONFIG_FUSION_LAN is not set
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_LAN is not set
# CONFIG_I2O_SCSI is not set
# CONFIG_I2O_PROC is not set
#
# Networking options
#
CONFIG_PACKET=m
# CONFIG_PACKET_MMAP is not set
CONFIG_NETLINK_DEV=y
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_FILTER=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
# CONFIG_IP_ADVANCED_ROUTER is not set
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
# CONFIG_IP_PIMSM_V2 is not set
# CONFIG_ARPD is not set
# CONFIG_INET_ECN is not set
CONFIG_SYN_COOKIES=y
#
# IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_IRC=m
# CONFIG_IP_NF_QUEUE is not set
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_MAC=m
# CONFIG_IP_NF_MATCH_PKTTYPE is not set
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_ECN=m
# CONFIG_IP_NF_MATCH_DSCP is not set
CONFIG_IP_NF_MATCH_AH_ESP=m
CONFIG_IP_NF_MATCH_LENGTH=m
CONFIG_IP_NF_MATCH_TTL=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_HELPER=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_CONNTRACK=m
CONFIG_IP_NF_MATCH_UNCLEAN=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_MIRROR=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
# CONFIG_IP_NF_NAT_LOCAL is not set
CONFIG_IP_NF_NAT_SNMP_BASIC=m
CONFIG_IP_NF_NAT_IRC=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_ECN=m
CONFIG_IP_NF_TARGET_DSCP=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_ULOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
# CONFIG_IP_NF_ARPTABLES is not set
# CONFIG_IP_NF_COMPAT_IPCHAINS is not set
# CONFIG_IP_NF_COMPAT_IPFWADM is not set
# CONFIG_IPV6 is not set
#
# SCTP Configuration (EXPERIMENTAL)
#
CONFIG_IPV6_SCTP__=y
# CONFIG_IP_SCTP is not set
# CONFIG_ATM is not set
# CONFIG_VLAN_8021Q is not set
# CONFIG_LLC is not set
# CONFIG_IPX is not set
# CONFIG_ATALK is not set
# CONFIG_DEV_APPLETALK is not set
# CONFIG_DECNET is not set
# CONFIG_BRIDGE is not set
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
# CONFIG_NET_SCHED is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
# CONFIG_TUN is not set
# CONFIG_ETHERTAP is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_SUNLANCE is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNBMAC is not set
# CONFIG_SUNQE is not set
# CONFIG_SUNGEM is not set
CONFIG_NET_VENDOR_3COM=y
# CONFIG_EL1 is not set
# CONFIG_EL2 is not set
# CONFIG_ELPLUS is not set
# CONFIG_EL16 is not set
# CONFIG_ELMC is not set
# CONFIG_ELMC_II is not set
CONFIG_VORTEX=m
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
#
# Tulip family network device support
#
# CONFIG_NET_TULIP is not set
# CONFIG_HP100 is not set
# CONFIG_NET_ISA is not set
# CONFIG_NET_PCI is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_E1000 is not set
# CONFIG_E1000_NAPI is not set
# CONFIG_MYRI_SBUS is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SK98LIN is not set
# CONFIG_TIGON3 is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
# CONFIG_PPP is not set
# CONFIG_SLIP is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# PCMCIA network device support
#
CONFIG_NET_PCMCIA=y
# CONFIG_PCMCIA_3C589 is not set
# CONFIG_PCMCIA_3C574 is not set
# CONFIG_PCMCIA_FMVJ18X is not set
CONFIG_PCMCIA_PCNET=m
# CONFIG_PCMCIA_NMCLAN is not set
# CONFIG_PCMCIA_SMC91C92 is not set
# CONFIG_PCMCIA_XIRC2PS is not set
# CONFIG_PCMCIA_AXNET is not set
# CONFIG_ARCNET_COM20020_CS is not set
# CONFIG_PCMCIA_IBMTR is not set
# CONFIG_NET_PCMCIA_RADIO is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
# CONFIG_ISDN_BOOL is not set
#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
# CONFIG_PHONE_IXJ_PCMCIA is not set
#
# Input device support
#
CONFIG_INPUT=y
#
# Userland interfaces
#
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_PSAUX=y
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1600
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=1200
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_TSDEV is not set
CONFIG_INPUT_EVDEV=m
# CONFIG_INPUT_EVBUG is not set
#
# Input I/O drivers
#
# CONFIG_GAMEPORT is not set
CONFIG_SOUND_GAMEPORT=y
# CONFIG_GAMEPORT_NS558 is not set
# CONFIG_GAMEPORT_L4 is not set
# CONFIG_GAMEPORT_EMU10K1 is not set
# CONFIG_GAMEPORT_VORTEX is not set
# CONFIG_GAMEPORT_FM801 is not set
# CONFIG_GAMEPORT_CS461x is not set
# CONFIG_SERIO is not set
# CONFIG_SERIO_I8042 is not set
# CONFIG_SERIO_SERPORT is not set
# CONFIG_SERIO_CT82C710 is not set
# CONFIG_SERIO_PARKBD is not set
#
# Input Device Drivers
#
CONFIG_INPUT_KEYBOARD=y
# CONFIG_KEYBOARD_ATKBD is not set
# CONFIG_KEYBOARD_SUNKBD is not set
# CONFIG_KEYBOARD_XTKBD is not set
# CONFIG_KEYBOARD_NEWTON is not set
CONFIG_INPUT_MOUSE=y
# CONFIG_MOUSE_PS2 is not set
# CONFIG_MOUSE_SERIAL is not set
# CONFIG_MOUSE_INPORT is not set
# CONFIG_MOUSE_LOGIBM is not set
# CONFIG_MOUSE_PC110PAD is not set
# CONFIG_INPUT_JOYSTICK is not set
# CONFIG_JOYSTICK_ANALOG is not set
# CONFIG_JOYSTICK_A3D is not set
# CONFIG_JOYSTICK_ADI is not set
# CONFIG_JOYSTICK_COBRA is not set
# CONFIG_JOYSTICK_GF2K is not set
# CONFIG_JOYSTICK_GRIP is not set
# CONFIG_JOYSTICK_GRIP_MP is not set
# CONFIG_JOYSTICK_GUILLEMOT is not set
# CONFIG_JOYSTICK_INTERACT is not set
# CONFIG_JOYSTICK_SIDEWINDER is not set
# CONFIG_JOYSTICK_TMDC is not set
# CONFIG_JOYSTICK_IFORCE is not set
# CONFIG_JOYSTICK_WARRIOR is not set
# CONFIG_JOYSTICK_MAGELLAN is not set
# CONFIG_JOYSTICK_SPACEORB is not set
# CONFIG_JOYSTICK_SPACEBALL is not set
# CONFIG_JOYSTICK_STINGER is not set
# CONFIG_JOYSTICK_TWIDDLER is not set
# CONFIG_JOYSTICK_DB9 is not set
# CONFIG_JOYSTICK_GAMECON is not set
# CONFIG_JOYSTICK_TURBOGRAFX is not set
# CONFIG_INPUT_JOYDUMP is not set
# CONFIG_INPUT_TOUCHSCREEN is not set
# CONFIG_TOUCHSCREEN_GUNZE is not set
CONFIG_INPUT_MISC=y
CONFIG_INPUT_PCSPKR=m
# CONFIG_INPUT_UINPUT is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_HW_CONSOLE=y
# CONFIG_SERIAL_NONSTANDARD is not set
#
# Serial drivers
#
# CONFIG_SERIAL_8250 is not set
# CONFIG_SERIAL_8250_CONSOLE is not set
# CONFIG_SERIAL_8250_CS is not set
# CONFIG_SERIAL_8250_EXTENDED is not set
# CONFIG_SERIAL_8250_MANY_PORTS is not set
# CONFIG_SERIAL_8250_SHARE_IRQ is not set
# CONFIG_SERIAL_8250_DETECT_IRQ is not set
# CONFIG_SERIAL_8250_MULTIPORT is not set
# CONFIG_SERIAL_8250_RSA is not set
#
# Non-8250 serial port support
#
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
# CONFIG_PPDEV is not set
# CONFIG_TIPAR is not set
#
# I2C support
#
# CONFIG_I2C is not set
#
# Mice
#
# CONFIG_BUSMOUSE is not set
# CONFIG_QIC02_TAPE is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_INTEL_RNG is not set
CONFIG_AMD_RNG=m
# CONFIG_NVRAM is not set
CONFIG_RTC=m
CONFIG_GEN_RTC=m
CONFIG_GEN_RTC_X=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=m
# CONFIG_AGP_INTEL is not set
# CONFIG_AGP_I810 is not set
# CONFIG_AGP_VIA is not set
CONFIG_AGP_AMD=y
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_SWORKS is not set
# CONFIG_AGP_AMD_8151 is not set
CONFIG_DRM=y
# CONFIG_DRM_TDFX is not set
# CONFIG_DRM_R128 is not set
# CONFIG_DRM_RADEON is not set
# CONFIG_DRM_I810 is not set
# CONFIG_DRM_I830 is not set
# CONFIG_DRM_MGA is not set
#
# PCMCIA character devices
#
# CONFIG_SYNCLINK_CS is not set
# CONFIG_MWAVE is not set
# CONFIG_SCx200_GPIO is not set
# CONFIG_RAW_DRIVER is not set
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# File systems
#
# CONFIG_QUOTA is not set
# CONFIG_QFMT_V1 is not set
# CONFIG_QFMT_V2 is not set
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
CONFIG_REISERFS_PROC_INFO=y
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BEFS_FS is not set
# CONFIG_BEFS_DEBUG is not set
# CONFIG_BFS_FS is not set
CONFIG_EXT3_FS=m
CONFIG_JBD=m
# CONFIG_JBD_DEBUG is not set
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
# CONFIG_UMSDOS_FS is not set
CONFIG_VFAT_FS=m
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
# CONFIG_JFFS2_FS is not set
# CONFIG_CRAMFS is not set
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_ZISOFS=y
# CONFIG_JFS_FS is not set
# CONFIG_JFS_DEBUG is not set
# CONFIG_JFS_STATISTICS is not set
# CONFIG_MINIX_FS is not set
# CONFIG_VXFS_FS is not set
CONFIG_NTFS_FS=m
# CONFIG_NTFS_DEBUG is not set
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
CONFIG_DEVFS_FS=y
CONFIG_DEVFS_MOUNT=y
# CONFIG_DEVFS_DEBUG is not set
# CONFIG_DEVPTS_FS is not set
# CONFIG_QNX4FS_FS is not set
# CONFIG_QNX4FS_RW is not set
# CONFIG_ROMFS_FS is not set
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
# CONFIG_UDF_FS is not set
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
# CONFIG_UFS_FS_WRITE is not set
# CONFIG_XFS_FS is not set
# CONFIG_XFS_RT is not set
# CONFIG_XFS_QUOTA is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
# CONFIG_NFS_V4 is not set
# CONFIG_ROOT_NFS is not set
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
# CONFIG_NFSD_V4 is not set
# CONFIG_NFSD_TCP is not set
CONFIG_SUNRPC=m
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_EXPORTFS=m
# CONFIG_CIFS is not set
CONFIG_SMB_FS=m
# CONFIG_SMB_NLS_DEFAULT is not set
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
# CONFIG_AFS_FS is not set
CONFIG_ZISOFS_FS=m
#
# Partition Types
#
# CONFIG_PARTITION_ADVANCED is not set
CONFIG_MSDOS_PARTITION=y
CONFIG_SMB_NLS=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1250=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
CONFIG_VIDEO_SELECT=y
# CONFIG_MDA_CONSOLE is not set
#
# Frame-buffer support
#
CONFIG_FB=y
CONFIG_DUMMY_CONSOLE=y
# CONFIG_FB_CLGEN is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
CONFIG_FB_VESA=y
# CONFIG_FB_VGA16 is not set
# CONFIG_FB_HGA is not set
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_RIVA is not set
# CONFIG_FB_MATROX is not set
# CONFIG_FB_ATY is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_NEOMAGIC is not set
# CONFIG_FB_3DFX is not set
# CONFIG_FB_VOODOO1 is not set
# CONFIG_FB_TRIDENT is not set
# CONFIG_FB_PM3 is not set
# CONFIG_FB_VIRTUAL is not set
# CONFIG_FBCON_ADVANCED is not set
CONFIG_FBCON_CFB24=y
CONFIG_FBCON_ACCEL=y
# CONFIG_FBCON_FONTWIDTH8_ONLY is not set
# CONFIG_FBCON_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
#
# Sound
#
CONFIG_SOUND=m
#
# Open Sound System
#
CONFIG_SOUND_PRIME=m
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not set
CONFIG_SOUND_EMU10K1=m
CONFIG_MIDI_EMU10K1=y
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_MIDI_VIA82CXXX is not set
# CONFIG_SOUND_OSS is not set
# CONFIG_SOUND_TVMIXER is not set
#
# Advanced Linux Sound Architecture
#
CONFIG_SND=m
CONFIG_SND_SEQUENCER=m
# CONFIG_SND_SEQ_DUMMY is not set
# CONFIG_SND_OSSEMUL is not set
CONFIG_SND_RTCTIMER=m
# CONFIG_SND_VERBOSE_PRINTK is not set
# CONFIG_SND_DEBUG is not set
# CONFIG_SND_DEBUG_MEMORY is not set
# CONFIG_SND_DEBUG_DETECT is not set
#
# Generic devices
#
# CONFIG_SND_DUMMY is not set
# CONFIG_SND_VIRMIDI is not set
# CONFIG_SND_MTPAV is not set
# CONFIG_SND_SERIAL_U16550 is not set
# CONFIG_SND_MPU401 is not set
#
# PCI devices
#
# CONFIG_SND_ALI5451 is not set
# CONFIG_SND_CS46XX is not set
# CONFIG_SND_CS46XX_NEW_DSP is not set
# CONFIG_SND_CS4281 is not set
CONFIG_SND_EMU10K1=m
# CONFIG_SND_KORG1212 is not set
# CONFIG_SND_NM256 is not set
# CONFIG_SND_RME32 is not set
# CONFIG_SND_RME96 is not set
# CONFIG_SND_RME9652 is not set
# CONFIG_SND_HDSP is not set
# CONFIG_SND_TRIDENT is not set
# CONFIG_SND_YMFPCI is not set
# CONFIG_SND_ALS4000 is not set
# CONFIG_SND_CMIPCI is not set
# CONFIG_SND_ENS1370 is not set
# CONFIG_SND_ENS1371 is not set
# CONFIG_SND_ES1938 is not set
# CONFIG_SND_ES1968 is not set
# CONFIG_SND_MAESTRO3 is not set
# CONFIG_SND_FM801 is not set
# CONFIG_SND_ICE1712 is not set
# CONFIG_SND_INTEL8X0 is not set
# CONFIG_SND_SONICVIBES is not set
# CONFIG_SND_VIA82XX is not set
#
# ALSA USB devices
#
# CONFIG_SND_USB_AUDIO is not set
#
# USB support
#
CONFIG_USB=m
CONFIG_USB_DEBUG=y
#
# Miscellaneous USB options
#
CONFIG_USB_DEVICEFS=y
CONFIG_USB_LONG_TIMEOUT=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_DYNAMIC_MINORS is not set
#
# USB Host Controller Drivers
#
# CONFIG_USB_EHCI_HCD is not set
CONFIG_USB_OHCI_HCD=m
# CONFIG_USB_UHCI_HCD_ALT is not set
#
# USB Device Class drivers
#
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH_TTY is not set
# CONFIG_USB_MIDI is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
CONFIG_USB_STORAGE=m
CONFIG_USB_STORAGE_DEBUG=y
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
#
# USB Human Interface Devices (HID)
#
CONFIG_USB_HID=m
CONFIG_USB_HIDINPUT=y
# CONFIG_HID_FF is not set
# CONFIG_HID_PID is not set
# CONFIG_LOGITECH_FF is not set
CONFIG_USB_HIDDEV=y
#
# USB HID Boot Protocol drivers
#
CONFIG_USB_KBD=m
CONFIG_USB_MOUSE=m
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_XPAD is not set
#
# USB Imaging devices
#
# CONFIG_USB_MDC800 is not set
# CONFIG_USB_SCANNER is not set
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
#
# USB Multimedia devices
#
# CONFIG_USB_DABUSB is not set
#
# Video4Linux support is needed for USB Multimedia device support
#
# CONFIG_USB_VICAM is not set
# CONFIG_USB_DSBR is not set
# CONFIG_USB_IBMCAM is not set
# CONFIG_USB_KONICAWC is not set
# CONFIG_USB_OV511 is not set
# CONFIG_USB_PWC is not set
# CONFIG_USB_SE401 is not set
# CONFIG_USB_STV680 is not set
#
# USB Network adaptors
#
# CONFIG_USB_CATC is not set
# CONFIG_USB_CDCETHER is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_USBNET is not set
#
# USB port drivers
#
# CONFIG_USB_USS720 is not set
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
# CONFIG_USB_SERIAL_GENERIC is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_IPAQ is not set
# CONFIG_USB_SERIAL_IR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28 is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28X is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28XA is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28XB is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19 is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA18X is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19W is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19QW is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19QI is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA49W is not set
# CONFIG_USB_SERIAL_KLSI is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_SAFE is not set
# CONFIG_USB_SERIAL_SAFE_PADDED is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_XIRCOM is not set
# CONFIG_USB_SERIAL_OMNINET is not set
#
# USB Miscellaneous drivers
#
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_BRLVGER is not set
# CONFIG_USB_LCD is not set
# CONFIG_USB_SPEEDTOUCH is not set
# CONFIG_USB_TEST is not set
#
# Bluetooth support
#
# CONFIG_BT is not set
#
# Profiling support
#
# CONFIG_PROFILING is not set
#
# Kernel hacking
#
# CONFIG_SOFTWARE_SUSPEND is not set
CONFIG_DEBUG_KERNEL=y
# CONFIG_DEBUG_STACKOVERFLOW is not set
# CONFIG_DEBUG_SLAB is not set
# CONFIG_DEBUG_IOVIRT is not set
CONFIG_MAGIC_SYSRQ=y
# CONFIG_DEBUG_SPINLOCK is not set
CONFIG_KALLSYMS=y
# CONFIG_X86_STACK_CHECK is not set
CONFIG_IOMMU_DEBUG=y
#
# Security options
#
CONFIG_SECURITY_CAPABILITIES=y
#
# Library routines
#
CONFIG_CRC32=m
CONFIG_ZLIB_INFLATE=m
# CONFIG_ZLIB_DEFLATE is not set
CONFIG_X86_SMP=y
CONFIG_X86_HT=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_MPPARSE=y
CONFIG_X86_TRAMPOLINE=y
CONFIG_X86_BIOS_REBOOT=y
CONFIG_X86_TSC=y
CONFIG_X86_EXTRA_IRQS=y
CONFIG_X86_FIND_SMP_CONFIG=y
CONFIG_X86_MPPARSE=y
[-- Attachment #3: syslog --]
[-- Type: text/plain, Size: 60230 bytes --]
Oct 28 12:27:53 badb syslogd 1.4.1#10: restart.
Oct 28 12:27:53 badb kernel: klogd 1.4.1#10, log source = /proc/kmsg started.
Oct 28 12:27:53 badb kernel: Inspecting /boot/System.map-2.5.44-ac5
Oct 28 12:27:53 badb kernel: Loaded 16349 symbols from /boot/System.map-2.5.44-ac5.
Oct 28 12:27:53 badb kernel: Symbols match kernel version 2.5.44.
Oct 28 12:27:53 badb kernel: Error seeking in /dev/kmem
Oct 28 12:27:53 badb kernel: Symbol #nfs, value f8ade000
Oct 28 12:27:53 badb kernel: Error adding kernel module table entry.
Oct 28 12:27:53 badb kernel: I NVS)
Oct 28 12:27:53 badb kernel: user: 000000003ff00000 - 000000003ff80000 (usable)
Oct 28 12:27:53 badb kernel: user: 000000003ff80000 - 0000000040000000 (reserved)
Oct 28 12:27:53 badb kernel: user: 00000000fec00000 - 00000000fec04000 (reserved)
Oct 28 12:27:53 badb kernel: user: 00000000fee00000 - 00000000fee01000 (reserved)
Oct 28 12:27:53 badb kernel: user: 00000000fff80000 - 0000000100000000 (reserved)
Oct 28 12:27:53 badb kernel: Warning only 896MB will be used.
Oct 28 12:27:53 badb kernel: Use a HIGHMEM enabled kernel.
Oct 28 12:27:53 badb kernel: 896MB LOWMEM available.
Oct 28 12:27:53 badb kernel: found SMP MP-table at 000f7170
Oct 28 12:27:53 badb kernel: hm, page 000f7000 reserved twice.
Oct 28 12:27:53 badb kernel: hm, page 000f8000 reserved twice.
Oct 28 12:27:53 badb kernel: hm, page 0009f000 reserved twice.
Oct 28 12:27:53 badb kernel: hm, page 000a0000 reserved twice.
Oct 28 12:27:53 badb kernel: On node 0 totalpages: 229376
Oct 28 12:27:53 badb kernel: DMA zone: 4096 pages
Oct 28 12:27:53 badb kernel: Normal zone: 225280 pages
Oct 28 12:27:53 badb kernel: HighMem zone: 0 pages
Oct 28 12:27:53 badb kernel: Intel MultiProcessor Specification v1.4
Oct 28 12:27:53 badb kernel: Virtual Wire compatibility mode.
Oct 28 12:27:53 badb kernel: OEM ID: TYAN Product ID: PAULANER APIC at: 0xFEE00000
Oct 28 12:27:53 badb kernel: Processor #1 6:6 APIC version 16
Oct 28 12:27:53 badb kernel: Processor #0 6:6 APIC version 16
Oct 28 12:27:53 badb kernel: I/O APIC #2 Version 17 at 0xFEC00000.
Oct 28 12:27:53 badb kernel: Enabling APIC mode: Flat. Using 1 I/O APICs
Oct 28 12:27:53 badb kernel: Processors: 2
Oct 28 12:27:53 badb kernel: Building zonelist for node : 0
Oct 28 12:27:53 badb kernel: Kernel command line: auto BOOT_IMAGE=Linux ro root=901 mem=1024M
Oct 28 12:27:53 badb kernel: Initializing CPU#0
Oct 28 12:27:53 badb kernel: Detected 1666.359 MHz processor.
Oct 28 12:27:53 badb kernel: Console: colour VGA+ 80x60
Oct 28 12:27:53 badb kernel: Calibrating delay loop... 3284.99 BogoMIPS
Oct 28 12:27:53 badb kernel: Memory: 905328k/917504k available (1195k kernel code, 11788k reserved, 1050k data, 104k init, 0k highmem)
Oct 28 12:27:53 badb kernel: Security Scaffold v1.0.0 initialized
Oct 28 12:27:53 badb kernel: Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Oct 28 12:27:53 badb kernel: Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Oct 28 12:27:53 badb kernel: Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Oct 28 12:27:53 badb kernel: CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
Oct 28 12:27:53 badb kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Oct 28 12:27:53 badb kernel: CPU: L2 Cache: 256K (64 bytes/line)
Oct 28 12:27:53 badb kernel: CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Oct 28 12:27:53 badb kernel: CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
Oct 28 12:27:53 badb kernel: CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
Oct 28 12:27:53 badb kernel: Enabling fast FPU save and restore... done.
Oct 28 12:27:53 badb kernel: Enabling unmasked SIMD FPU exception support... done.
Oct 28 12:27:53 badb kernel: Checking 'hlt' instruction... OK.
Oct 28 12:27:53 badb kernel: POSIX conformance testing by UNIFIX
Oct 28 12:27:53 badb kernel: CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
Oct 28 12:27:53 badb kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Oct 28 12:27:53 badb kernel: CPU: L2 Cache: 256K (64 bytes/line)
Oct 28 12:27:53 badb kernel: CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Oct 28 12:27:53 badb kernel: CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
Oct 28 12:27:53 badb kernel: CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
Oct 28 12:27:53 badb kernel: CPU0: AMD Athlon(tm) MP 2000+ stepping 02
Oct 28 12:27:53 badb kernel: per-CPU timeslice cutoff: 731.44 usecs.
Oct 28 12:27:53 badb kernel: task migration cache decay timeout: 1 msecs.
Oct 28 12:27:53 badb kernel: masked ExtINT on CPU#0
Oct 28 12:27:53 badb kernel: ESR value before enabling vector: 00000000
Oct 28 12:27:53 badb kernel: ESR value after enabling vector: 00000000
Oct 28 12:27:53 badb kernel: Booting processor 1/0 eip 2000
Oct 28 12:27:53 badb kernel: Initializing CPU#1
Oct 28 12:27:53 badb kernel: masked ExtINT on CPU#1
Oct 28 12:27:53 badb kernel: ESR value before enabling vector: 00000000
Oct 28 12:27:53 badb kernel: ESR value after enabling vector: 00000000
Oct 28 12:27:53 badb kernel: Calibrating delay loop... 3325.95 BogoMIPS
Oct 28 12:27:53 badb kernel: CPU: Before vendor init, caps: 0383fbff c1cbfbff 00000000, vendor = 2
Oct 28 12:27:53 badb kernel: CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
Oct 28 12:27:53 badb kernel: CPU: L2 Cache: 256K (64 bytes/line)
Oct 28 12:27:53 badb kernel: CPU: After vendor init, caps: 0383fbff c1cbfbff 00000000 00000000
Oct 28 12:27:53 badb kernel: CPU: After generic, caps: 0383fbff c1cbfbff 00000000 00000000
Oct 28 12:27:53 badb kernel: CPU: Common caps: 0383fbff c1cbfbff 00000000 00000000
Oct 28 12:27:53 badb kernel: CPU1: AMD Athlon(tm) Processor stepping 02
Oct 28 12:27:53 badb kernel: Total of 2 processors activated (6610.94 BogoMIPS).
Oct 28 12:27:53 badb kernel: ENABLING IO-APIC IRQs
Oct 28 12:27:53 badb kernel: Setting 2 in the phys_id_present_map
Oct 28 12:27:53 badb kernel: ...changing IO-APIC physical APIC ID to 2 ... ok.
Oct 28 12:27:53 badb kernel: init IO_APIC IRQs
Oct 28 12:27:53 badb kernel: IO-APIC (apicid-pin) 2-0, 2-5, 2-10, 2-11, 2-16, 2-20, 2-21, 2-22, 2-23 not connected.
Oct 28 12:27:53 badb kernel: ..TIMER: vector=0x31 pin1=2 pin2=0
Oct 28 12:27:53 badb kernel: number of MP IRQ sources: 20.
Oct 28 12:27:53 badb kernel: number of IO-APIC #2 registers: 24.
Oct 28 12:27:53 badb kernel: testing the IO APIC.......................
Oct 28 12:27:53 badb kernel:
Oct 28 12:27:53 badb kernel: IO APIC #2......
Oct 28 12:27:53 badb kernel: .... register #00: 02000000
Oct 28 12:27:53 badb kernel: ....... : physical APIC id: 02
Oct 28 12:27:53 badb kernel: ....... : Delivery Type: 0
Oct 28 12:27:53 badb kernel: ....... : LTS : 0
Oct 28 12:27:53 badb kernel: .... register #01: 00170011
Oct 28 12:27:53 badb kernel: ....... : max redirection entries: 0017
Oct 28 12:27:53 badb kernel: ....... : PRQ implemented: 0
Oct 28 12:27:53 badb kernel: ....... : IO APIC version: 0011
Oct 28 12:27:53 badb kernel: .... register #02: 00000000
Oct 28 12:27:53 badb kernel: ....... : arbitration: 00
Oct 28 12:27:53 badb kernel: .... IRQ redirection table:
Oct 28 12:27:53 badb kernel: NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
Oct 28 12:27:53 badb kernel: 00 000 00 1 0 0 0 0 0 0 00
Oct 28 12:27:53 badb kernel: 01 001 01 0 0 0 0 0 1 1 39
Oct 28 12:27:53 badb kernel: 02 001 01 0 0 0 0 0 1 1 31
Oct 28 12:27:53 badb kernel: 03 001 01 0 0 0 0 0 1 1 41
Oct 28 12:27:53 badb kernel: 04 001 01 0 0 0 0 0 1 1 49
Oct 28 12:27:53 badb kernel: 05 000 00 1 0 0 0 0 0 0 00
Oct 28 12:27:53 badb kernel: 06 001 01 0 0 0 0 0 1 1 51
Oct 28 12:27:53 badb kernel: 07 001 01 0 0 0 0 0 1 1 59
Oct 28 12:27:53 badb kernel: 08 001 01 0 0 0 0 0 1 1 61
Oct 28 12:27:53 badb kernel: 09 001 01 0 0 0 0 0 1 1 69
Oct 28 12:27:53 badb kernel: 0a 000 00 1 0 0 0 0 0 0 00
Oct 28 12:27:53 badb kernel: 0b 000 00 1 0 0 0 0 0 0 00
Oct 28 12:27:53 badb kernel: 0c 001 01 0 0 0 0 0 1 1 71
Oct 28 12:27:53 badb kernel: 0d 001 01 0 0 0 0 0 1 1 79
Oct 28 12:27:53 badb kernel: 0e 001 01 0 0 0 0 0 1 1 81
Oct 28 12:27:53 badb kernel: 0f 001 01 0 0 0 0 0 1 1 89
Oct 28 12:27:53 badb kernel: 10 000 00 1 0 0 0 0 0 0 00
Oct 28 12:27:53 badb kernel: 11 001 01 1 1 0 1 0 1 1 91
Oct 28 12:27:53 badb kernel: 12 001 01 1 1 0 1 0 1 1 99
Oct 28 12:27:53 badb kernel: 13 001 01 1 1 0 1 0 1 1 A1
Oct 28 12:27:53 badb kernel: 14 000 00 1 0 0 0 0 0 0 00
Oct 28 12:27:53 badb kernel: 15 000 00 1 0 0 0 0 0 0 00
Oct 28 12:27:53 badb kernel: 16 000 00 1 0 0 0 0 0 0 00
Oct 28 12:27:53 badb kernel: 17 000 00 1 0 0 0 0 0 0 00
Oct 28 12:27:53 badb kernel: IRQ to pin mappings:
Oct 28 12:27:53 badb kernel: IRQ0 -> 0:2
Oct 28 12:27:53 badb kernel: IRQ1 -> 0:1
Oct 28 12:27:53 badb kernel: IRQ3 -> 0:3
Oct 28 12:27:53 badb kernel: IRQ4 -> 0:4
Oct 28 12:27:53 badb kernel: IRQ6 -> 0:6
Oct 28 12:27:53 badb kernel: IRQ7 -> 0:7
Oct 28 12:27:53 badb kernel: IRQ8 -> 0:8
Oct 28 12:27:53 badb kernel: IRQ9 -> 0:9
Oct 28 12:27:53 badb kernel: IRQ12 -> 0:12
Oct 28 12:27:53 badb kernel: IRQ13 -> 0:13
Oct 28 12:27:53 badb kernel: IRQ14 -> 0:14
Oct 28 12:27:53 badb kernel: IRQ15 -> 0:15
Oct 28 12:27:53 badb kernel: IRQ17 -> 0:17
Oct 28 12:27:53 badb kernel: IRQ18 -> 0:18
Oct 28 12:27:53 badb kernel: IRQ19 -> 0:19
Oct 28 12:27:53 badb kernel: .................................... done.
Oct 28 12:27:53 badb kernel: Using local APIC timer interrupts.
Oct 28 12:27:53 badb kernel: calibrating APIC timer ...
Oct 28 12:27:53 badb kernel: ..... CPU clock speed is 1666.0407 MHz.
Oct 28 12:27:53 badb kernel: ..... host bus clock speed is 266.0625 MHz.
Oct 28 12:27:53 badb kernel: checking TSC synchronization across 2 CPUs: passed.
Oct 28 12:27:53 badb kernel: Starting migration thread for cpu 0
Oct 28 12:27:53 badb kernel: Bringing up 1
Oct 28 12:27:53 badb kernel: CPU 1 IS NOW UP!
Oct 28 12:27:53 badb kernel: Starting migration thread for cpu 1
Oct 28 12:27:53 badb kernel: CPUS done 2
Oct 28 12:27:53 badb kernel: Linux NET4.0 for Linux 2.4
Oct 28 12:27:53 badb kernel: Based upon Swansea University Computer Society NET3.039
Oct 28 12:27:53 badb kernel: Initializing RT netlink socket
Oct 28 12:27:53 badb kernel: mtrr: v2.0 (20020519)
Oct 28 12:27:53 badb kernel: mtrr: your CPUs had inconsistent fixed MTRR settings
Oct 28 12:27:53 badb kernel: mtrr: probably your BIOS does not setup all CPUs
Oct 28 12:27:53 badb kernel: PCI: PCI BIOS revision 2.10 entry at 0xfd7d0, last bus=2
Oct 28 12:27:53 badb kernel: PCI: Using configuration type 1
Oct 28 12:27:53 badb kernel: Registering system device cpu0
Oct 28 12:27:53 badb kernel: adding '' to cpu class interfaces
Oct 28 12:27:53 badb kernel: Registering system device cpu1
Oct 28 12:27:53 badb kernel: adding '' to cpu class interfaces
Oct 28 12:27:53 badb kernel: BIO: pool of 256 setup, 14Kb (56 bytes/bio)
Oct 28 12:27:53 badb kernel: biovec pool[0]: 1 bvecs: 256 entries (12 bytes)
Oct 28 12:27:53 badb kernel: biovec pool[1]: 4 bvecs: 256 entries (48 bytes)
Oct 28 12:27:53 badb kernel: biovec pool[2]: 16 bvecs: 256 entries (192 bytes)
Oct 28 12:27:53 badb kernel: biovec pool[3]: 64 bvecs: 256 entries (768 bytes)
Oct 28 12:27:53 badb kernel: biovec pool[4]: 128 bvecs: 256 entries (1536 bytes)
Oct 28 12:27:53 badb kernel: biovec pool[5]: 256 bvecs: 256 entries (3072 bytes)
Oct 28 12:27:53 badb kernel: PCI: Probing PCI hardware
Oct 28 12:27:53 badb kernel: PCI: Probing PCI hardware (bus 00)
Oct 28 12:27:53 badb kernel: PCI->APIC IRQ transform: (B0,I9,P0) -> 17
Oct 28 12:27:53 badb kernel: PCI->APIC IRQ transform: (B1,I5,P0) -> 18
Oct 28 12:27:53 badb kernel: PCI->APIC IRQ transform: (B2,I0,P3) -> 19
Oct 28 12:27:53 badb kernel: PCI->APIC IRQ transform: (B2,I5,P0) -> 17
Oct 28 12:27:53 badb kernel: PCI->APIC IRQ transform: (B2,I6,P0) -> 18
Oct 28 12:27:53 badb kernel: PCI->APIC IRQ transform: (B2,I7,P0) -> 19
Oct 28 12:27:53 badb kernel: PCI->APIC IRQ transform: (B2,I8,P0) -> 19
Oct 28 12:27:53 badb kernel: Registering system device pic0
Oct 28 12:27:53 badb kernel: Registering system device rtc0
Oct 28 12:27:53 badb kernel: Starting kswapd
Oct 28 12:27:53 badb kernel: aio_setup: sizeof(struct page) = 40
Oct 28 12:27:53 badb kernel: devfs: v1.21 (20020820) Richard Gooch (rgooch@atnf.csiro.au)
Oct 28 12:27:53 badb kernel: devfs: boot_options: 0x1
Oct 28 12:27:53 badb kernel: Capability LSM initialized
Oct 28 12:27:53 badb kernel: BIOS failed to enable PCI standards compliance, fixing this error.
Oct 28 12:27:53 badb kernel: pty: 256 Unix98 ptys configured
Oct 28 12:27:53 badb kernel: block request queues:
Oct 28 12:27:53 badb kernel: 128 requests per read queue
Oct 28 12:27:53 badb kernel: 128 requests per write queue
Oct 28 12:27:53 badb kernel: 8 requests per batch
Oct 28 12:27:53 badb kernel: enter congestion at 31
Oct 28 12:27:53 badb kernel: exit congestion at 33
Oct 28 12:27:53 badb kernel: SCSI subsystem driver Revision: 1.00
Oct 28 12:27:53 badb kernel: scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4
Oct 28 12:27:53 badb kernel: <Adaptec 29160 Ultra160 SCSI adapter>
Oct 28 12:27:53 badb kernel: aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
Oct 28 12:27:53 badb kernel:
Oct 28 12:27:53 badb kernel: (scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Oct 28 12:27:53 badb kernel: Vendor: QUANTUM Model: ATLAS10K2-TY367J Rev: DA40
Oct 28 12:27:53 badb kernel: Type: Direct-Access ANSI SCSI revision: 03
Oct 28 12:27:53 badb kernel: scsi0:A:0:0: Tagged Queuing enabled. Depth 253
Oct 28 12:27:53 badb kernel: (scsi0:A:1): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Oct 28 12:27:53 badb kernel: Vendor: QUANTUM Model: ATLAS10K2-TY367J Rev: DA40
Oct 28 12:27:53 badb kernel: Type: Direct-Access ANSI SCSI revision: 03
Oct 28 12:27:53 badb kernel: scsi0:A:1:0: Tagged Queuing enabled. Depth 253
Oct 28 12:27:53 badb kernel: (scsi0:A:2): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Oct 28 12:27:53 badb kernel: Vendor: QUANTUM Model: ATLAS10K2-TY367J Rev: DA40
Oct 28 12:27:53 badb kernel: Type: Direct-Access ANSI SCSI revision: 03
Oct 28 12:27:53 badb kernel: scsi0:A:2:0: Tagged Queuing enabled. Depth 253
Oct 28 12:27:53 badb kernel: (scsi0:A:3): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Oct 28 12:27:53 badb kernel: Vendor: QUANTUM Model: ATLAS10K2-TY367J Rev: DA40
Oct 28 12:27:53 badb kernel: Type: Direct-Access ANSI SCSI revision: 03
Oct 28 12:27:53 badb kernel: scsi0:A:3:0: Tagged Queuing enabled. Depth 253
Oct 28 12:27:53 badb kernel: (scsi0:A:4): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Oct 28 12:27:53 badb kernel: Vendor: QUANTUM Model: ATLAS10K2-TY367J Rev: DA40
Oct 28 12:27:53 badb kernel: Type: Direct-Access ANSI SCSI revision: 03
Oct 28 12:27:53 badb kernel: scsi0:A:4:0: Tagged Queuing enabled. Depth 253
Oct 28 12:27:53 badb kernel: scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4
Oct 28 12:27:53 badb kernel: <Adaptec 2940 Ultra2 SCSI adapter>
Oct 28 12:27:53 badb kernel: aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/253 SCBs
Oct 28 12:27:53 badb kernel:
Oct 28 12:27:53 badb kernel: (scsi1:A:0): 80.000MB/s transfers (40.000MHz, offset 31, 16bit)
Oct 28 12:27:53 badb kernel: Vendor: QUANTUM Model: ATLAS 10K 18WLS Rev: UCH0
Oct 28 12:27:53 badb kernel: Type: Direct-Access ANSI SCSI revision: 03
Oct 28 12:27:53 badb kernel: scsi1:A:0:0: Tagged Queuing enabled. Depth 253
Oct 28 12:27:53 badb kernel: (scsi1:A:3): 40.000MB/s transfers (20.000MHz, offset 32, 16bit)
Oct 28 12:27:53 badb kernel: Vendor: HP Model: C5683A Rev: C908
Oct 28 12:27:53 badb kernel: Type: Sequential-Access ANSI SCSI revision: 02
Oct 28 12:27:53 badb kernel: (scsi1:A:4): 20.000MB/s transfers (20.000MHz, offset 8)
Oct 28 12:27:53 badb kernel: Vendor: PIONEER Model: DVD-ROM DVD-303 Rev: 1.09
Oct 28 12:27:53 badb kernel: Type: CD-ROM ANSI SCSI revision: 02
Oct 28 12:27:53 badb kernel: (scsi1:A:6): 10.000MB/s transfers (10.000MHz, offset 15)
Oct 28 12:27:53 badb kernel: Vendor: HP Model: CD-Writer+ 9200 Rev: 1.0c
Oct 28 12:27:53 badb kernel: Type: CD-ROM ANSI SCSI revision: 04
Oct 28 12:27:53 badb kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Oct 28 12:27:53 badb kernel: Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
Oct 28 12:27:53 badb kernel: Attached scsi disk sdc at scsi0, channel 0, id 2, lun 0
Oct 28 12:27:53 badb kernel: Attached scsi disk sdd at scsi0, channel 0, id 3, lun 0
Oct 28 12:27:53 badb kernel: Attached scsi disk sde at scsi0, channel 0, id 4, lun 0
Oct 28 12:27:53 badb kernel: Attached scsi disk sdf at scsi1, channel 0, id 0, lun 0
Oct 28 12:27:53 badb kernel: SCSI device sda: drive cache: write through
Oct 28 12:27:53 badb kernel: SCSI device sda: 71132959 512-byte hdwr sectors (36420 MB)
Oct 28 12:27:53 badb kernel: /dev/scsi/host0/bus0/target0/lun0: p1 < p5 p6 p7 p8 >
Oct 28 12:27:53 badb kernel: SCSI device sdb: drive cache: write through
Oct 28 12:27:53 badb kernel: SCSI device sdb: 71132959 512-byte hdwr sectors (36420 MB)
Oct 28 12:27:53 badb kernel: /dev/scsi/host0/bus0/target1/lun0: p1 < p5 p6 p7 p8 >
Oct 28 12:27:53 badb kernel: SCSI device sdc: drive cache: write through
Oct 28 12:27:53 badb kernel: SCSI device sdc: 71132959 512-byte hdwr sectors (36420 MB)
Oct 28 12:27:53 badb kernel: /dev/scsi/host0/bus0/target2/lun0: p1 < p5 p6 p7 p8 >
Oct 28 12:27:53 badb kernel: SCSI device sdd: drive cache: write through
Oct 28 12:27:53 badb kernel: SCSI device sdd: 71132959 512-byte hdwr sectors (36420 MB)
Oct 28 12:27:53 badb kernel: /dev/scsi/host0/bus0/target3/lun0: p1 < p5 p6 p7 p8 >
Oct 28 12:27:53 badb kernel: SCSI device sde: drive cache: write through
Oct 28 12:27:53 badb kernel: SCSI device sde: 71132959 512-byte hdwr sectors (36420 MB)
Oct 28 12:27:53 badb kernel: /dev/scsi/host0/bus0/target4/lun0: p1 < p5 p6 p7 p8 >
Oct 28 12:27:53 badb kernel: SCSI device sdf: drive cache: write back
Oct 28 12:27:53 badb kernel: SCSI device sdf: 35877972 512-byte hdwr sectors (18370 MB)
Oct 28 12:27:53 badb kernel: /dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 p10 p11 p12 >
Oct 28 12:27:53 badb kernel: md: raid0 personality registered as nr 2
Oct 28 12:27:53 badb kernel: md: raid1 personality registered as nr 3
Oct 28 12:27:53 badb kernel: md: raid5 personality registered as nr 4
Oct 28 12:27:53 badb kernel: raid5: measuring checksumming speed
Oct 28 12:27:53 badb kernel: 8regs : 2524.000 MB/sec
Oct 28 12:27:53 badb kernel: 32regs : 2296.000 MB/sec
Oct 28 12:27:53 badb kernel: pIII_sse : 3548.000 MB/sec
Oct 28 12:27:53 badb kernel: pII_mmx : 3904.000 MB/sec
Oct 28 12:27:53 badb kernel: p5_mmx : 4988.000 MB/sec
Oct 28 12:27:53 badb kernel: raid5: using function: pIII_sse (3548.000 MB/sec)
Oct 28 12:27:53 badb kernel: md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
Oct 28 12:27:53 badb kernel: md: Autodetecting RAID arrays.
Oct 28 12:27:53 badb kernel: [events: 000000b5]
Oct 28 12:27:53 badb kernel: [events: 000000b0]
Oct 28 12:27:53 badb kernel: [events: 000000aa]
Oct 28 12:27:53 badb kernel: [events: 000000a6]
Oct 28 12:27:53 badb kernel: [events: 000000b5]
Oct 28 12:27:53 badb kernel: [events: 000000b0]
Oct 28 12:27:53 badb kernel: [events: 000000aa]
Oct 28 12:27:53 badb kernel: [events: 000000a6]
Oct 28 12:27:53 badb kernel: [events: 000000b0]
Oct 28 12:27:53 badb kernel: [events: 000000aa]
Oct 28 12:27:53 badb kernel: [events: 000000a6]
Oct 28 12:27:53 badb kernel: [events: 000000b0]
Oct 28 12:27:53 badb kernel: [events: 000000aa]
Oct 28 12:27:53 badb kernel: [events: 000000a6]
Oct 28 12:27:53 badb kernel: [events: 000000b0]
Oct 28 12:27:53 badb kernel: [events: 000000aa]
Oct 28 12:27:53 badb kernel: [events: 000000a6]
Oct 28 12:27:53 badb kernel: md: autorun ...
Oct 28 12:27:53 badb kernel: md: considering scsi/host0/bus0/target4/lun0/part8 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target4/lun0/part8 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target3/lun0/part8 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target2/lun0/part8 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target1/lun0/part8 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target0/lun0/part8 ...
Oct 28 12:27:53 badb kernel: md: created md3
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target0/lun0/part8>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target1/lun0/part8>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target2/lun0/part8>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target3/lun0/part8>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target4/lun0/part8>
Oct 28 12:27:53 badb kernel: md: running: <scsi/host0/bus0/target4/lun0/part8><scsi/host0/bus0/target3/lun0/part8><scsi/host0/bus0/target2/lun0/part8><scsi/host0/bus0/target1/lun0/part8><scsi/host0/bus0/target0/lun0/part8>
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target4/lun0/part8's event counter: 000000a6
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target3/lun0/part8's event counter: 000000a6
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target2/lun0/part8's event counter: 000000a6
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target1/lun0/part8's event counter: 000000a6
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target0/lun0/part8's event counter: 000000a6
Oct 28 12:27:53 badb kernel: md3: max total readahead window set to 992k
Oct 28 12:27:53 badb kernel: md3: 4 data-disks, max readahead per data-disk: 248k
Oct 28 12:27:53 badb kernel: md3: setting max_sectors to 64, segment boundary to 16383
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target4/lun0/part8 operational as raid disk 4
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target3/lun0/part8 operational as raid disk 3
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target2/lun0/part8 operational as raid disk 2
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target1/lun0/part8 operational as raid disk 1
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target0/lun0/part8 operational as raid disk 0
Oct 28 12:27:53 badb kernel: raid5: allocated 5223kB for md3
Oct 28 12:27:53 badb kernel: raid5: raid level 5 set md3 active with 5 out of 5 devices, algorithm 0
Oct 28 12:27:53 badb kernel: RAID5 conf printout:
Oct 28 12:27:53 badb kernel: --- rd:5 wd:5 fd:0
Oct 28 12:27:53 badb kernel: disk 0, o:1, dev:scsi/host0/bus0/target0/lun0/part8
Oct 28 12:27:53 badb kernel: disk 1, o:1, dev:scsi/host0/bus0/target1/lun0/part8
Oct 28 12:27:53 badb kernel: disk 2, o:1, dev:scsi/host0/bus0/target2/lun0/part8
Oct 28 12:27:53 badb kernel: disk 3, o:1, dev:scsi/host0/bus0/target3/lun0/part8
Oct 28 12:27:53 badb kernel: disk 4, o:1, dev:scsi/host0/bus0/target4/lun0/part8
Oct 28 12:27:53 badb kernel: md: updating md3 RAID superblock on device
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target4/lun0/part8 [events: 000000a7]<6>(write) scsi/host0/bus0/target4/lun0/part8's sb offset: 28201984
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target3/lun0/part8 [events: 000000a7]<6>(write) scsi/host0/bus0/target3/lun0/part8's sb offset: 28201984
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target2/lun0/part8 [events: 000000a7]<6>(write) scsi/host0/bus0/target2/lun0/part8's sb offset: 28201984
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target1/lun0/part8 [events: 000000a7]<6>(write) scsi/host0/bus0/target1/lun0/part8's sb offset: 28201984
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target0/lun0/part8 [events: 000000a7]<6>(write) scsi/host0/bus0/target0/lun0/part8's sb offset: 28201984
Oct 28 12:27:53 badb kernel: md: considering scsi/host0/bus0/target4/lun0/part7 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target4/lun0/part7 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target3/lun0/part7 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target2/lun0/part7 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target1/lun0/part7 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target0/lun0/part7 ...
Oct 28 12:27:53 badb kernel: md: created md2
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target0/lun0/part7>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target1/lun0/part7>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target2/lun0/part7>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target3/lun0/part7>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target4/lun0/part7>
Oct 28 12:27:53 badb kernel: md: running: <scsi/host0/bus0/target4/lun0/part7><scsi/host0/bus0/target3/lun0/part7><scsi/host0/bus0/target2/lun0/part7><scsi/host0/bus0/target1/lun0/part7><scsi/host0/bus0/target0/lun0/part7>
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target4/lun0/part7's event counter: 000000aa
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target3/lun0/part7's event counter: 000000aa
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target2/lun0/part7's event counter: 000000aa
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target1/lun0/part7's event counter: 000000aa
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target0/lun0/part7's event counter: 000000aa
Oct 28 12:27:53 badb kernel: md2: max total readahead window set to 992k
Oct 28 12:27:53 badb kernel: md2: 4 data-disks, max readahead per data-disk: 248k
Oct 28 12:27:53 badb kernel: md2: setting max_sectors to 64, segment boundary to 16383
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target4/lun0/part7 operational as raid disk 4
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target3/lun0/part7 operational as raid disk 3
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target2/lun0/part7 operational as raid disk 2
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target1/lun0/part7 operational as raid disk 1
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target0/lun0/part7 operational as raid disk 0
Oct 28 12:27:53 badb kernel: raid5: allocated 5223kB for md2
Oct 28 12:27:53 badb kernel: raid5: raid level 5 set md2 active with 5 out of 5 devices, algorithm 0
Oct 28 12:27:53 badb kernel: RAID5 conf printout:
Oct 28 12:27:53 badb kernel: --- rd:5 wd:5 fd:0
Oct 28 12:27:53 badb kernel: disk 0, o:1, dev:scsi/host0/bus0/target0/lun0/part7
Oct 28 12:27:53 badb kernel: disk 1, o:1, dev:scsi/host0/bus0/target1/lun0/part7
Oct 28 12:27:53 badb kernel: disk 2, o:1, dev:scsi/host0/bus0/target2/lun0/part7
Oct 28 12:27:53 badb kernel: disk 3, o:1, dev:scsi/host0/bus0/target3/lun0/part7
Oct 28 12:27:53 badb kernel: disk 4, o:1, dev:scsi/host0/bus0/target4/lun0/part7
Oct 28 12:27:53 badb kernel: md: updating md2 RAID superblock on device
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target4/lun0/part7 [events: 000000ab]<6>(write) scsi/host0/bus0/target4/lun0/part7's sb offset: 4200896
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target3/lun0/part7 [events: 000000ab]<6>(write) scsi/host0/bus0/target3/lun0/part7's sb offset: 4200896
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target2/lun0/part7 [events: 000000ab]<6>(write) scsi/host0/bus0/target2/lun0/part7's sb offset: 4200896
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target1/lun0/part7 [events: 000000ab]<6>(write) scsi/host0/bus0/target1/lun0/part7's sb offset: 4200896
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target0/lun0/part7 [events: 000000ab]<6>(write) scsi/host0/bus0/target0/lun0/part7's sb offset: 4200896
Oct 28 12:27:53 badb kernel: md: considering scsi/host0/bus0/target4/lun0/part6 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target4/lun0/part6 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target3/lun0/part6 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target2/lun0/part6 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target1/lun0/part6 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target0/lun0/part6 ...
Oct 28 12:27:53 badb kernel: md: created md1
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target0/lun0/part6>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target1/lun0/part6>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target2/lun0/part6>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target3/lun0/part6>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target4/lun0/part6>
Oct 28 12:27:53 badb kernel: md: running: <scsi/host0/bus0/target4/lun0/part6><scsi/host0/bus0/target3/lun0/part6><scsi/host0/bus0/target2/lun0/part6><scsi/host0/bus0/target1/lun0/part6><scsi/host0/bus0/target0/lun0/part6>
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target4/lun0/part6's event counter: 000000b0
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target3/lun0/part6's event counter: 000000b0
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target2/lun0/part6's event counter: 000000b0
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target1/lun0/part6's event counter: 000000b0
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target0/lun0/part6's event counter: 000000b0
Oct 28 12:27:53 badb kernel: md1: max total readahead window set to 992k
Oct 28 12:27:53 badb kernel: md1: 4 data-disks, max readahead per data-disk: 248k
Oct 28 12:27:53 badb kernel: md1: setting max_sectors to 64, segment boundary to 16383
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target4/lun0/part6 operational as raid disk 4
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target3/lun0/part6 operational as raid disk 3
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target2/lun0/part6 operational as raid disk 2
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target1/lun0/part6 operational as raid disk 1
Oct 28 12:27:53 badb kernel: raid5: device scsi/host0/bus0/target0/lun0/part6 operational as raid disk 0
Oct 28 12:27:53 badb kernel: raid5: allocated 5223kB for md1
Oct 28 12:27:53 badb kernel: raid5: raid level 5 set md1 active with 5 out of 5 devices, algorithm 0
Oct 28 12:27:53 badb kernel: RAID5 conf printout:
Oct 28 12:27:53 badb kernel: --- rd:5 wd:5 fd:0
Oct 28 12:27:53 badb kernel: disk 0, o:1, dev:scsi/host0/bus0/target0/lun0/part6
Oct 28 12:27:53 badb kernel: disk 1, o:1, dev:scsi/host0/bus0/target1/lun0/part6
Oct 28 12:27:53 badb kernel: disk 2, o:1, dev:scsi/host0/bus0/target2/lun0/part6
Oct 28 12:27:53 badb kernel: disk 3, o:1, dev:scsi/host0/bus0/target3/lun0/part6
Oct 28 12:27:53 badb kernel: disk 4, o:1, dev:scsi/host0/bus0/target4/lun0/part6
Oct 28 12:27:53 badb kernel: md: updating md1 RAID superblock on device
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target4/lun0/part6 [events: 000000b1]<6>(write) scsi/host0/bus0/target4/lun0/part6's sb offset: 2104384
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target3/lun0/part6 [events: 000000b1]<6>(write) scsi/host0/bus0/target3/lun0/part6's sb offset: 2104384
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target2/lun0/part6 [events: 000000b1]<6>(write) scsi/host0/bus0/target2/lun0/part6's sb offset: 2104384
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target1/lun0/part6 [events: 000000b1]<6>(write) scsi/host0/bus0/target1/lun0/part6's sb offset: 2104384
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target0/lun0/part6 [events: 000000b1]<6>(write) scsi/host0/bus0/target0/lun0/part6's sb offset: 2104384
Oct 28 12:27:53 badb kernel: md: considering scsi/host0/bus0/target1/lun0/part5 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target1/lun0/part5 ...
Oct 28 12:27:53 badb kernel: md: adding scsi/host0/bus0/target0/lun0/part5 ...
Oct 28 12:27:53 badb kernel: md: created md0
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target0/lun0/part5>
Oct 28 12:27:53 badb kernel: md: bind<scsi/host0/bus0/target1/lun0/part5>
Oct 28 12:27:53 badb kernel: md: running: <scsi/host0/bus0/target1/lun0/part5><scsi/host0/bus0/target0/lun0/part5>
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target1/lun0/part5's event counter: 000000b5
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target0/lun0/part5's event counter: 000000b5
Oct 28 12:27:53 badb kernel: md0: max total readahead window set to 128k
Oct 28 12:27:53 badb kernel: md0: 1 data-disks, max readahead per data-disk: 128k
Oct 28 12:27:53 badb kernel: md0: setting max_sectors to 64, segment boundary to 16383
Oct 28 12:27:53 badb kernel: raid1: raid set md0 active with 2 out of 2 mirrors
Oct 28 12:27:53 badb kernel: md: updating md0 RAID superblock on device
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target1/lun0/part5 [events: 000000b6]<6>(write) scsi/host0/bus0/target1/lun0/part5's sb offset: 1052096
Oct 28 12:27:53 badb kernel: md: scsi/host0/bus0/target0/lun0/part5 [events: 000000b6]<6>(write) scsi/host0/bus0/target0/lun0/part5's sb offset: 1052096
Oct 28 12:27:53 badb kernel: md: ... autorun DONE.
Oct 28 12:27:53 badb kernel: NET4: Linux TCP/IP 1.0 for NET4.0
Oct 28 12:27:53 badb kernel: IP: routing cache hash table of 8192 buckets, 64Kbytes
Oct 28 12:27:53 badb kernel: TCP: Hash tables configured (established 262144 bind 65536)
Oct 28 12:27:53 badb kernel: Linux IP multicast router 0.06 plus PIM-SM
Oct 28 12:27:53 badb kernel: NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Oct 28 12:27:53 badb kernel: VFS: Mounted root (ext2 filesystem) readonly.
Oct 28 12:27:53 badb kernel: Mounted devfs on /dev
Oct 28 12:27:53 badb kernel: Freeing unused kernel memory: 104k freed
Oct 28 12:27:53 badb kernel: Adding 1052184k swap on /dev/scsi/host0/bus0/target2/lun0/part5. Priority:1 extents:1
Oct 28 12:27:53 badb kernel: Adding 1052184k swap on /dev/scsi/host0/bus0/target3/lun0/part5. Priority:1 extents:1
Oct 28 12:27:53 badb kernel: Adding 1052184k swap on /dev/scsi/host0/bus0/target4/lun0/part5. Priority:1 extents:1
Oct 28 12:27:53 badb kernel: Real Time Clock Driver v1.11
Oct 28 12:27:53 badb kernel: 3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
Oct 28 12:27:53 badb kernel: 02:06.0: 3Com PCI 3c905C Tornado at 0x2400. Vers LK1.1.18
Oct 28 12:27:53 badb kernel: phy=0, phyx=24, mii_status=0x782d
Oct 28 12:27:53 badb kernel: 02:08.0: 3Com PCI 3c905C Tornado at 0x2480. Vers LK1.1.18
Oct 28 12:27:53 badb kernel: phy=0, phyx=24, mii_status=0x782d
Oct 28 12:27:53 badb kernel: Creative EMU10K1 PCI Audio Driver, version 0.16, 12:20:43 Oct 28 2002
Oct 28 12:27:53 badb kernel: emu10k1: EMU10K1 rev 5 model 0x8040 found, IO at 0x2800-0x281f, IRQ 17
Oct 28 12:27:53 badb kernel: ac97_codec: AC97 Audio codec, id: 0x8384:0x7609 (SigmaTel STAC9721/23)
Oct 28 12:27:53 badb kernel: ip_tables: (C) 2000-2002 Netfilter core team
Oct 28 12:27:53 badb kernel: inserting floppy driver for 2.5.44-ac5
Oct 28 12:27:53 badb kernel: FDC 0 is a post-1991 82077
Oct 28 12:27:53 badb kernel: Attached scsi CD-ROM sr0 at scsi1, channel 0, id 4, lun 0
Oct 28 12:27:53 badb kernel: Attached scsi CD-ROM sr1 at scsi1, channel 0, id 6, lun 0
Oct 28 12:27:53 badb kernel: sr0: scsi3-mmc drive: 0x/0x cd/rw xa/form2 cdda tray
Oct 28 12:27:53 badb kernel: Uniform CD-ROM driver Revision: 3.12
Oct 28 12:27:53 badb kernel: sr1: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Oct 28 12:27:53 badb kernel: st: Version 20021015, fixed bufsize 32768, wrt 30720, s/g segs 256
Oct 28 12:27:53 badb kernel: Attached scsi tape st0 at scsi1, channel 0, id 3, lun 0
Oct 28 12:27:53 badb kernel: st0: try direct i/o: yes, max page reachable by HBA 1048575
Oct 28 12:27:53 badb kernel: st0: Block limits 1 - 16777215 bytes.
Oct 28 12:27:53 badb kernel: st0: Mode 0 options: buffer writes: 1, async writes: 1, read ahead: 1
Oct 28 12:27:53 badb kernel: st0: can bsr: 1, two FMs: 0, fast mteom: 0, auto lock: 1,
Oct 28 12:27:53 badb kernel: st0: defs for wr: 0, no block limits: 0, partitions: 1, s2 log: 1
Oct 28 12:27:53 badb kernel: st0: sysv: 0 nowait: 0
Oct 28 12:27:53 badb kernel: st0: Default block size set to 0 bytes.
Oct 28 12:27:53 badb kernel: st0: Compression default set to 1
Oct 28 12:27:53 badb kernel: st0: Mode 1 options: buffer writes: 1, async writes: 1, read ahead: 1
Oct 28 12:27:53 badb kernel: st0: can bsr: 1, two FMs: 0, fast mteom: 0, auto lock: 1,
Oct 28 12:27:53 badb kernel: st0: defs for wr: 0, no block limits: 0, partitions: 1, s2 log: 1
Oct 28 12:27:53 badb kernel: st0: sysv: 0 nowait: 0
Oct 28 12:27:53 badb kernel: st0: Default block size set to 1024 bytes.
Oct 28 12:27:53 badb kernel: st0: Compression default set to 1
Oct 28 12:27:53 badb kernel: st0: Mode 2 options: buffer writes: 1, async writes: 1, read ahead: 1
Oct 28 12:27:53 badb kernel: st0: can bsr: 1, two FMs: 0, fast mteom: 0, auto lock: 1,
Oct 28 12:27:53 badb kernel: st0: defs for wr: 0, no block limits: 0, partitions: 1, s2 log: 1
Oct 28 12:27:53 badb kernel: st0: sysv: 0 nowait: 0
Oct 28 12:27:53 badb kernel: st0: Default block size set to 0 bytes.
Oct 28 12:27:53 badb kernel: st0: Compression default set to 0
Oct 28 12:27:53 badb kernel: st0: Mode 3 options: buffer writes: 1, async writes: 1, read ahead: 1
Oct 28 12:27:53 badb kernel: st0: can bsr: 1, two FMs: 0, fast mteom: 0, auto lock: 1,
Oct 28 12:27:53 badb kernel: st0: defs for wr: 0, no block limits: 0, partitions: 1, s2 log: 1
Oct 28 12:27:53 badb kernel: st0: sysv: 0 nowait: 0
Oct 28 12:27:53 badb kernel: st0: Default block size set to 1024 bytes.
Oct 28 12:27:53 badb kernel: st0: Compression default set to 0
Oct 28 12:27:53 badb kernel: parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP]
Oct 28 12:27:53 badb kernel: parport0: irq 7 detected
Oct 28 12:27:53 badb kernel: parport0: cpp_mux: aa55f00f52ad51(87)
Oct 28 12:27:53 badb kernel: parport0: cpp_daisy: aa5500ff(80)
Oct 28 12:27:53 badb kernel: parport0: assign_addrs: aa5500ff(80)
Oct 28 12:27:53 badb kernel: parport0: cpp_mux: aa55f00f52ad51(87)
Oct 28 12:27:53 badb kernel: parport0: cpp_daisy: aa5500ff(80)
Oct 28 12:27:53 badb kernel: parport0: assign_addrs: aa5500ff(80)
Oct 28 12:27:53 badb kernel: lp0: using parport0 (polling).
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: registered new driver usbfs
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: registered new driver hub
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-pci.c: 2002-Sep-17 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-pci.c: block sizes: ed 64 td 64
Oct 28 12:27:53 badb kernel: drivers/usb/core/hcd-pci.c: ohci-hcd @ 02:00.0, Advanced Micro Devices [AMD] AMD-768 [Opus] USB
Oct 28 12:27:53 badb kernel: drivers/usb/core/hcd-pci.c: irq 19, pci mem f8ab0000
Oct 28 12:27:53 badb kernel: drivers/usb/core/hcd.c: new USB bus registered, assigned bus number 1
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-hcd.c: USB HC TakeOver from SMM
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-hcd.c: USB HC reset_hc 02:00.0: ctrl = 0x683 ;
Oct 28 12:27:53 badb kernel: drivers/usb/core/hcd.c: 02:00.0 root hub device address 1
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: new device strings: Mfr=3, Product=2, SerialNumber=1
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_hotplug
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_new_device_Rsmp_6d928d58 - registering 1-0:0
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_device_probe_Rsmp_baeeec4e
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_device_probe_Rsmp_baeeec4e - got id
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: USB hub found at 0
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: 4 ports detected
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: standalone hub
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: ganged power switching
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: global over-current protection
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: Port indicators are not supported
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: power on to power good time: 2ms
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: hub controller current requirement: 0mA
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: local power source is good
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: no over-current condition exists
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: enabling power on all ports
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_hotplug
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: 02:00.0: created debug files
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: OHCI controller 02:00.0 state
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: OHCI 1.0, with legacy support registers
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: control: 0x0000068f RWE RWC HCFS=operational IE PLE CBSR=3
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: cmdstatus: 0x00000000 SOC=0
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: intrstatus: 0x00000044 RHSC SF
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: intrenable: 0x80000002 MIE WDH
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: hcca frame #0017
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: roothub.a: 01000204 POTPGT=1 NPS NDP=4
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: roothub.b: 00000000 PPCM=0000 DR=0000
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: roothub.status: 00000000
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: 02:00.0: roothub.portstatus [0] = 0x00000100 PPS
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: 02:00.0: roothub.portstatus [1] = 0x00010101 CSC PPS CCS
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: 02:00.0: roothub.portstatus [2] = 0x00000100 PPS
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-dbg.c: 02:00.0: roothub.portstatus [3] = 0x00000100 PPS
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 1, portstatus 100, change 0, 12 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-hub.c: 02:00.0: GetStatus roothub.portstatus [2] = 0x00010101 CSC PPS CCS
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 2, portstatus 101, change 1, 12 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: hub 0 port 2 connection change
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: hub 0 port 2, portstatus 101, change 1, 12 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 2, portstatus 101, change 0, 12 Mb/s
Oct 28 12:27:53 badb last message repeated 3 times
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-hub.c: 02:00.0: GetStatus roothub.portstatus [2] = 0x00100103 PRSC PPS PES CCS
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 2, portstatus 103, change 10, 12 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: new USB device 02:00.0-2, assigned address 2
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: new device strings: Mfr=0, Product=0, SerialNumber=0
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_hotplug
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_new_device_Rsmp_6d928d58 - registering 1-2:0
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_device_probe_Rsmp_baeeec4e
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_device_probe_Rsmp_baeeec4e - got id
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: USB hub found at 2
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: 4 ports detected
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: standalone hub
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: individual port power switching
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: individual port over-current protection
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: Port indicators are not supported
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: power on to power good time: 100ms
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: hub controller current requirement: 100mA
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: local power source is good
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: no over-current condition exists
Oct 28 12:27:53 badb kernel: drivers/usb/host/ohci-q.c: 02:00.0: link ed f5c8f040 branch 0 [11us.], interval 32
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: enabling power on all ports
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_hotplug
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 3, portstatus 100, change 0, 12 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 4, portstatus 100, change 0, 12 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 1, portstatus 100, change 0, 12 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 2, portstatus 301, change 1, 1.5 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: hub 2 port 2 connection change
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: hub 2 port 2, portstatus 301, change 1, 1.5 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 2, portstatus 301, change 0, 1.5 Mb/s
Oct 28 12:27:53 badb last message repeated 3 times
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 2, portstatus 303, change 10, 1.5 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: new USB device 02:00.0-2.2, assigned address 3
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: new device strings: Mfr=4, Product=12, SerialNumber=0
Oct 28 12:27:53 badb kernel: Product: ELLIPSE
Oct 28 12:27:53 badb kernel: Manufacturer: MGE
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_hotplug
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_new_device_Rsmp_6d928d58 - registering 1-2.2:0
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_hotplug
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 3, portstatus 301, change 1, 1.5 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: hub 2 port 3 connection change
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: hub 2 port 3, portstatus 301, change 1, 1.5 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 3, portstatus 301, change 0, 1.5 Mb/s
Oct 28 12:27:53 badb last message repeated 3 times
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 3, portstatus 303, change 10, 1.5 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: new USB device 02:00.0-2.3, assigned address 4
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
Oct 28 12:27:53 badb kernel: Product: Microsoft Wireless Intellimouse Explorer® 1.0A
Oct 28 12:27:53 badb kernel: Manufacturer: Microsoft
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_hotplug
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_new_device_Rsmp_6d928d58 - registering 1-2.3:0
Oct 28 12:27:53 badb kernel: drivers/usb/core/usb.c: usb_hotplug
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 4, portstatus 100, change 0, 12 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 1, portstatus 100, change 0, 12 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 2, portstatus 303, change 0, 1.5 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 3, portstatus 303, change 0, 1.5 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: port 4, portstatus 100, change 0, 12 Mb/s
Oct 28 12:27:53 badb kernel: drivers/usb/core/hub.c: usb_hub_thread exiting
Oct 28 12:27:54 badb slapd[605]: daemon: socket() failed errno=97 (Address family not supported by protocol)
Oct 28 12:27:55 badb /etc/hotplug/usb.agent: Setup hid for USB product 463/ffff/1
Oct 28 12:27:55 badb kernel: drivers/usb/core/usb.c: registered new driver hiddev
Oct 28 12:27:55 badb kernel: drivers/usb/core/usb.c: usb_device_probe_Rsmp_baeeec4e
Oct 28 12:27:55 badb kernel: drivers/usb/core/usb.c: usb_device_probe_Rsmp_baeeec4e - got id
Oct 28 12:27:55 badb root: spamd starting
Oct 28 12:27:56 badb /etc/hotplug/usb.agent: Setup usbmouse hid for USB product 45e/59/d
Oct 28 12:27:56 badb /etc/hotplug/usb.agent: Setup mousedev for USB product 45e/59/d
Oct 28 12:27:56 badb kernel: register interface 'mouse' with class 'input
Oct 28 12:27:56 badb kernel: mice: PS/2 mouse device common for all mice
Oct 28 12:27:56 badb named[656]: starting BIND 9.2.1
Oct 28 12:27:56 badb named[656]: using 2 CPUs
Oct 28 12:27:56 badb named[658]: loading configuration from '/etc/bind/named.conf'
Oct 28 12:27:56 badb authdaemond.plain: authdaemon: modules="authpam", daemons=1
Oct 28 12:27:56 badb named[658]: no IPv6 interfaces found
Oct 28 12:27:56 badb named[658]: listening on IPv4 interface lo, 127.0.0.1#53
Oct 28 12:27:56 badb named[658]: listening on IPv4 interface eth0, 10.13.0.103#53
Oct 28 12:27:56 badb named[658]: listening on IPv4 interface eth1, 10.14.0.162#53
Oct 28 12:27:56 badb named[658]: command channel listening on 127.0.0.1#953
Oct 28 12:27:57 badb named[658]: zone 0.in-addr.arpa/IN: loaded serial 1
Oct 28 12:27:57 badb named[658]: zone 10.in-addr.arpa/IN: loaded serial 2002091901
Oct 28 12:27:57 badb named[658]: zone 127.in-addr.arpa/IN: loaded serial 1
Oct 28 12:27:57 badb named[658]: zone 255.in-addr.arpa/IN: loaded serial 1
Oct 28 12:27:57 badb named[658]: zone merlin.org/IN: loaded serial 2002091101
Oct 28 12:27:57 badb named[658]: zone 0.in-addr.arpa/IN: loaded serial 1
Oct 28 12:27:57 badb named[658]: zone 127.in-addr.arpa/IN: loaded serial 1
Oct 28 12:27:57 badb named[658]: zone 255.in-addr.arpa/IN: loaded serial 1
Oct 28 12:27:57 badb named[658]: running
Oct 28 12:27:57 badb lwresd[766]: starting BIND 9.2.1
Oct 28 12:27:57 badb lwresd[766]: using 2 CPUs
Oct 28 12:27:57 badb lwresd[769]: loading configuration from '/etc/bind/lwresd.conf'
Oct 28 12:27:57 badb lwresd[769]: none:0: open: /etc/bind/lwresd.conf: file not found
Oct 28 12:27:57 badb lwresd[769]: loading configuration from '/etc/resolv.conf'
Oct 28 12:27:57 badb lwresd[769]: no IPv6 interfaces found
Oct 28 12:27:57 badb lwresd[769]: couldn't add command channel 127.0.0.1#953: address in use
Oct 28 12:27:57 badb lwresd[769]: lwres listening on 127.0.0.1#921
Oct 28 12:27:57 badb lwresd[769]: running
Oct 28 12:27:57 badb upsd[785]: Warning: Data for UPS [lugh] is stale - check driver
Oct 28 12:27:57 badb upsd[786]: Startup successful
Oct 28 12:27:58 badb cardmgr[812]: starting, version is 3.1.33
Oct 28 12:27:58 badb cardmgr[812]: no pcmcia driver in /proc/devices
Oct 28 12:27:58 badb cardmgr[812]: exiting
Oct 28 12:27:59 badb named[658]: socket.c:1100: unexpected error:
Oct 28 12:27:59 badb named[658]: internal_send: 10.15.0.2#53: Invalid argument
Oct 28 12:27:59 badb kernel: udp cork app bug 1
Oct 28 12:27:59 badb named[659]: socket.c:1100: unexpected error:
Oct 28 12:27:59 badb named[659]: internal_send: 10.13.0.105#53: Invalid argument
Oct 28 12:27:59 badb kernel: udp cork app bug 1
Oct 28 12:27:59 badb named[658]: socket.c:1100: unexpected error:
Oct 28 12:27:59 badb named[658]: internal_send: 10.14.0.162#53: Invalid argument
Oct 28 12:27:59 badb kernel: udp cork app bug 1
Oct 28 12:28:01 badb kernel: drivers/usb/core/file.c: asking for 1 minors, starting at 96
Oct 28 12:28:01 badb kernel: drivers/usb/core/file.c: found a minor chunk free, starting at 96
Oct 28 12:28:01 badb kernel: hiddev96: USB HID v1.00 Device [MGE ELLIPSE] on usb-02:00.0-2.2
Oct 28 12:28:01 badb kernel: drivers/usb/core/usb.c: usb_device_probe_Rsmp_baeeec4e
Oct 28 12:28:01 badb kernel: drivers/usb/core/usb.c: usb_device_probe_Rsmp_baeeec4e - got id
Oct 28 12:28:01 badb kernel: drivers/usb/host/ohci-q.c: urb f30a8cc0 usb-02:00.0-2.3 ep-0-OUT cc 4 --> status -32
Oct 28 12:28:01 badb kernel: drivers/usb/core/hcd.c: giveback urb f30a8cc0 status -32 len 0
Oct 28 12:28:01 badb kernel: drivers/usb/host/ohci-q.c: urb f30a8cc0 usb-02:00.0-2.3 ep-0-OUT cc 4 --> status -32
Oct 28 12:28:01 badb kernel: drivers/usb/core/hcd.c: giveback urb f30a8cc0 status -32 len 0
Oct 28 12:28:01 badb kernel: input: USB HID v1.10 Mouse [Microsoft Microsoft Wireless Intellimouse Explorer® 1.0A] on usb-02:00.0-2.3
Oct 28 12:28:01 badb kernel: drivers/usb/core/usb.c: registered new driver hid
Oct 28 12:28:01 badb kernel: drivers/usb/input/hid-core.c: v2.0:USB HID core driver
Oct 28 12:28:01 badb /sbin/hotplug: no runnable /etc/hotplug/input.agent is installed
Oct 28 12:28:01 badb spamd[625]: server started on port 783 (running version 2.42)
Oct 28 12:28:03 badb postfix/postfix-script: starting the Postfix mail system
Oct 28 12:28:03 badb postfix/master[913]: daemon started
Oct 28 12:28:03 badb postfix/nqmgr[916]: 84D0986E42: from=<>, size=5504, nrcpt=1 (queue active)
Oct 28 12:28:03 badb postfix/nqmgr[916]: C2CDD867F1: from=<>, size=11517, nrcpt=1 (queue active)
Oct 28 12:28:03 badb postfix/nqmgr[916]: 725BD8682D: from=<>, size=3577, nrcpt=1 (queue active)
Oct 28 12:28:03 badb postfix/nqmgr[916]: A992086A90: from=<>, size=3927, nrcpt=1 (queue active)
Oct 28 12:28:03 badb postfix/nqmgr[916]: 6B75C86824: from=<>, size=20529, nrcpt=1 (queue active)
Oct 28 12:28:03 badb postfix/nqmgr[916]: D6411868F0: from=<>, size=8873, nrcpt=1 (queue active)
Oct 28 12:28:03 badb postfix/nqmgr[916]: B7477867B9: from=<>, size=5255, nrcpt=1 (queue active)
Oct 28 12:28:03 badb postfix/nqmgr[916]: B5E62867B3: from=<>, size=2385, nrcpt=1 (queue active)
Oct 28 12:28:03 badb postfix/nqmgr[916]: 371E786937: from=<>, size=3445, nrcpt=1 (queue active)
Oct 28 12:28:03 badb named[658]: socket.c:1100: unexpected error:
Oct 28 12:28:03 badb named[658]: internal_send: 10.15.0.38#53: Invalid argument
Oct 28 12:28:03 badb kernel: udp cork app bug 1
Oct 28 12:28:03 badb rpc.statd[951]: Version 1.0.2 Starting
Oct 28 12:28:04 badb chronyd[974]: chronyd version V1_14 starting
Oct 28 12:28:04 badb chronyd[974]: Linux kernel major=2 minor=5 patch=44
Oct 28 12:28:04 badb chronyd[974]: Fatal error : Kernel version not supported yet, sorry.
Oct 28 12:28:04 badb chronyd[974]: Unexpected condition [File handler not registered] at sched.c:190, core dumped
Oct 28 12:28:04 badb /usr/sbin/cron[980]: (CRON) INFO (pidfile fd = 3)
Oct 28 12:28:04 badb /usr/sbin/cron[981]: (CRON) STARTUP (fork ok)
Oct 28 12:28:04 badb /usr/sbin/cron[981]: (CRON) INFO (Running @reboot jobs)
Oct 28 12:28:04 badb /USR/SBIN/CRON[985]: (root) CMD (test -x /usr/sbin/logcheck && nice -n10 /usr/sbin/logcheck)
Oct 28 12:28:14 badb named[658]: socket.c:1100: unexpected error:
Oct 28 12:28:14 badb named[658]: internal_send: 10.15.0.1#53: Invalid argument
Oct 28 12:28:14 badb kernel: udp cork app bug 1
Oct 28 12:28:14 badb modprobe: modprobe: Can't locate module char-major-119
Oct 28 12:28:15 badb named[658]: socket.c:1100: unexpected error:
Oct 28 12:28:15 badb named[658]: internal_send: 10.15.0.1#53: Invalid argument
Oct 28 12:28:15 badb kernel: udp cork app bug 1
Oct 28 12:28:15 badb named[659]: socket.c:1100: unexpected error:
Oct 28 12:28:15 badb named[659]: internal_send: 10.15.0.1#53: Invalid argument
Oct 28 12:28:15 badb kernel: udp cork app bug 1
Oct 28 12:28:17 badb named[659]: socket.c:1100: unexpected error:
Oct 28 12:28:17 badb named[659]: internal_send: 10.15.0.3#53: Invalid argument
Oct 28 12:28:17 badb kernel: udp cork app bug 1
Oct 28 12:28:18 badb named[659]: socket.c:1100: unexpected error:
Oct 28 12:28:18 badb named[659]: internal_send: 10.15.0.38#53: Invalid argument
Oct 28 12:28:18 badb kernel: udp cork app bug 1
Oct 28 12:36:09 badb kernel: Incorrect number of segments after building list
Oct 28 12:36:09 badb kernel: counted 2, received 1
Oct 28 12:36:09 badb kernel: req nr_sec 8, cur_nr_sec 8
Oct 28 12:36:09 badb kernel: end_request: I/O error, dev 08:40, sector 6784528
Oct 28 12:36:09 badb kernel: raid5: Disk failure on scsi/host0/bus0/target4/lun0/part7, disabling device. Operation continuing on 4 devices
Oct 28 12:36:09 badb kernel: blk: request botched
Oct 28 12:36:09 badb kernel: ------------[ cut here ]------------
Oct 28 12:36:09 badb kernel: kernel BUG at drivers/scsi/scsi_lib.c:819!
Oct 28 12:36:09 badb kernel: invalid operand: 0000
Oct 28 12:36:09 badb kernel: mousedev hid nfs lockd sunrpc ohci-hcd usbcore parport_pc lp parport sg st sr_mod cdrom floppy iptable_filter ip_tables emu10k1 sound soundcore ac97_codec 3c59x rtc
Oct 28 12:36:09 badb kernel: CPU: 1
Oct 28 12:36:09 badb kernel: EIP: 0060:[scsi_init_io+279/304] Not tainted
Oct 28 12:36:09 badb kernel: EFLAGS: 00010286
Oct 28 12:36:09 badb kernel: EIP is at scsi_init_io+0x117/0x130
Oct 28 12:36:09 badb kernel: eax: f5bcda00 ebx: f5bcda00 ecx: 00000001 edx: f7f51580
Oct 28 12:36:09 badb kernel: esi: 00000002 edi: f7ed62c0 ebp: f78c9f90 esp: f78c9f60
Oct 28 12:36:09 badb kernel: ds: 0068 es: 0068 ss: 0068
Oct 28 12:36:09 badb kernel: Process raid5d (pid: 17, threadinfo=f78c8000 task=f7e0cd00)
Oct 28 12:36:09 badb kernel: Stack: f7ed62c0 f5bcda00 f7ef3400 c01aa8bb f5bcda00 f7ef34c8 f7ef3428 f7ea3680
Oct 28 12:36:09 badb kernel: f7f56800 f78c8000 c031fb20 c019d88e 00000001 c019eb5d f7ef3428 f7df434c
Oct 28 12:36:09 badb kernel: f78c9fb4 c019ed80 f7ef3428 f78c8000 f78c8000 f78c9fb4 f78c9fb4 c01d6abf
Oct 28 12:36:09 badb kernel: Call Trace:
Oct 28 12:36:09 badb kernel: [scsi_request_fn+779/1136] scsi_request_fn+0x30b/0x470
Oct 28 12:36:09 badb kernel: [elv_queue_empty+14/32] elv_queue_empty+0xe/0x20
Oct 28 12:36:09 badb kernel: [generic_unplug_device+141/192] generic_unplug_device+0x8d/0xc0
Oct 28 12:36:09 badb kernel: [blk_run_queues+176/192] blk_run_queues+0xb0/0xc0
Oct 28 12:36:09 badb kernel: [md_thread+415/528] md_thread+0x19f/0x210
Oct 28 12:36:09 badb kernel: [md_thread+0/528] md_thread+0x0/0x210
Oct 28 12:36:09 badb kernel: [default_wake_function+0/64] default_wake_function+0x0/0x40
Oct 28 12:36:09 badb kernel: [kernel_thread_helper+5/24] kernel_thread_helper+0x5/0x18
Oct 28 12:36:09 badb kernel:
Oct 28 12:36:09 badb kernel: Code: 0f 0b 33 03 42 b0 24 c0 90 31 c0 5b 5e 5f c3 8d 76 00 8d bc
Oct 28 12:36:09 badb kernel: <6>md: updating md2 RAID superblock on device
Oct 28 12:36:09 badb kernel: md: (skipping faulty scsi/host0/bus0/target4/lun0/part7 )
Oct 28 12:36:09 badb kernel: md: scsi/host0/bus0/target3/lun0/part7 [events: 000000ac]<6>(write) scsi/host0/bus0/target3/lun0/part7's sb offset: 4200896
Oct 28 12:36:09 badb kernel: md: scsi/host0/bus0/target2/lun0/part7 [events: 000000ac]<6>(write) scsi/host0/bus0/target2/lun0/part7's sb offset: 4200896
Oct 28 12:36:09 badb kernel: md: scsi/host0/bus0/target1/lun0/part7 [events: 000000ac]<6>(write) scsi/host0/bus0/target1/lun0/part7's sb offset: 4200896
Oct 28 12:36:09 badb kernel: md: scsi/host0/bus0/target0/lun0/part7 [events: 000000ac]<6>(write) scsi/host0/bus0/target0/lun0/part7's sb offset: 4200896
[-- Attachment #4: lspci --]
[-- Type: text/plain, Size: 1212 bytes --]
00:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] System Controller (rev 11)
00:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-760 MP [IGD4-2P] AGP Bridge
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ISA (rev 05)
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-768 [Opus] IDE (rev 04)
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] ACPI (rev 03)
00:09.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
00:10.0 PCI bridge: Advanced Micro Devices [AMD] AMD-768 [Opus] PCI (rev 05)
01:05.0 VGA compatible controller: nVidia Corporation NV25 [GeForce4 Ti4400] (rev a2)
02:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-768 [Opus] USB (rev 07)
02:04.0 CardBus bridge: Texas Instruments PCI1225 (rev 01)
02:04.1 CardBus bridge: Texas Instruments PCI1225 (rev 01)
02:05.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 05)
02:05.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 05)
02:06.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74)
02:07.0 SCSI storage controller: Adaptec AHA-2940U2/U2W
02:08.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
next reply other threads:[~2002-10-30 14:13 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-10-30 14:18 merlin hughes [this message]
2002-10-30 14:35 ` kernel BUG at drivers/scsi/scsi_lib.c:819 with 2.5.44-ac5 Jens Axboe
2002-10-30 15:43 ` merlin
2002-10-30 18:15 ` Patrick Mansfield
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20021030141812.BF07786921@primary.mx.nitric.com \
--to=merlin@merlin.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.