From: "Parrenin Frédéric" <Frederic.Parrenin-uJC2I/HWIrG1lNqXp+/2b1AUjnlXr6A1@public.gmane.org>
To: acpi-devel
<acpi-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>
Subject: /proc/acpi/battery empty on a samsung V20
Date: 13 Dec 2002 18:51:30 +0100 [thread overview]
Message-ID: <200212131754.gBDHsmt02104@cnes.fr> (raw)
Hi,
I have posted this problem already to the acpi-support mailing list, but
even with the help of Gunter and Derek (thanks again), I cannot solve
it.
ACPI seems to work fine on my laptop, except the battery and ac status.
The related directories in /proc/acpi exist, but are empty.
There are no messages related to battery or ac in my dmesg.
Note that there is the same problem with apm : suspend mode works (apm
-s), but the battery status is unavailable.
Perhaps a related problem : I have a interupts conflict.
My dmesg follows.
I would be happy to assist with any information you need.
Frederic
lspci:
00:00.0 Host bridge: Intel Corp.: Unknown device 2560 (rev 01)
00:02.0 VGA compatible controller: Intel Corp.: Unknown device 2562 (rev
01)
00:1d.0 USB Controller: Intel Corp.: Unknown device 24c2 (rev 01)
00:1d.1 USB Controller: Intel Corp.: Unknown device 24c4 (rev 01)
00:1d.2 USB Controller: Intel Corp.: Unknown device 24c7 (rev 01)
00:1d.7 USB Controller: Intel Corp.: Unknown device 24cd (rev 01)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA PCI Bridge (rev 81)
00:1f.0 ISA bridge: Intel Corp.: Unknown device 24c0 (rev 01)
00:1f.1 IDE interface: Intel Corp. 82801DB ICH4 IDE (rev 01)
00:1f.3 SMBus: Intel Corp.: Unknown device 24c3 (rev 01)
00:1f.5 Multimedia audio controller: Intel Corp.: Unknown device 24c5
(rev 01)
00:1f.6 Modem: Intel Corp.: Unknown device 24c6 (rev 01)
02:03.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)
02:08.0 Ethernet controller: Intel Corp.: Unknown device 1039 (rev 81)
02:0d.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22 1394a-2000
Controller
DMESG :
Linux version 2.4.20-1mdk (quintela-JAOzawC1ADxn+L6o72McsUEOCMrvLtNR@public.gmane.org) (gcc version
3.2 (Mandrake Linux 9.1 3.2-4mdk)) #1 Tue Dec 3 21:24:49 CET 2002
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000f6e0000 (usable)
BIOS-e820: 000000000f6e0000 - 000000000f6f0000 (ACPI data)
BIOS-e820: 000000000f6f0000 - 000000000f700000 (ACPI NVS)
BIOS-e820: 000000000f700000 - 000000000f780000 (usable)
BIOS-e820: 000000000f780000 - 0000000010000000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
247MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 63360
zone(0): 4096 pages.
zone(1): 59264 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 PTLTD ) @ 0x000f68a0
ACPI: RSDT (v001 PTLTD RSDT 01540.00000) @ 0x0f6eb074
ACPI: FADT (v001 SEC DRACO 01540.00000) @ 0x0f6eff64
ACPI: BOOT (v001 PTLTD $SBFTBL$ 01540.00000) @ 0x0f6effd8
ACPI: DSDT (v001 SEC DRACO 01540.00000) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: MADT not present
Kernel command line: BOOT_IMAGE=2.420.-1mdk ro root=305 quiet devfs=mount hdc=ide-scsi
ide_setup: hdc=ide-scsi
No local APIC present or hardware disabled
Initializing CPU#0
Detected 1695.027 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3381.65 BogoMIPS
Memory: 247808k/253440k available (1302k kernel code, 5116k reserved, 491k data, 140k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 0K, L1 D cache: 8K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febf9ff 00000000 00000000 00000000
CPU: Common caps: 3febf9ff 00000000 00000000 00000000
CPU: Intel(R) Celeron(R) CPU 1.70GHz stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch-r1x6VkxMR+00zabcByZE4g@public.gmane.org)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20021115
PCI: PCI BIOS revision 2.10 entry at 0xfd994, last bus=3
PCI: Using configuration type 1
ACPI-0508: *** Info: GPE Block0 defined as GPE0 to GPE31
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs *10)
ACPI: PCI Interrupt Link [LNKB] (IRQs *5)
ACPI: PCI Interrupt Link [LNKC] (IRQs *5)
ACPI: PCI Interrupt Link [LNKD] (IRQs *10)
ACPI: PCI Interrupt Link [LNKE] (IRQs *3)
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 9 10 11, disabled)
ACPI: PCI Interrupt Link [LNKG] (IRQs 4 5 9 10 11, disabled)
ACPI: PCI Interrupt Link [LNKH] (IRQs *3)
ACPI: Embedded Controller [H_EC] (gpe 24)
ACPI: Power Resource [PFAN] (on)
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 9
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: overridden by ACPI.
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch-r1x6VkxMR+00zabcByZE4g@public.gmane.org)
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller on PCI bus 00 dev f9
PCI: Device 00:1f.1 not available because of resource collisions
ICH4: BIOS setup was incomplete.
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio
hda: IC25N020ATCS04-0, ATA DISK drive
hdc: Samsung CD-RW/DVD-ROM SN-324B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
blk: queue c03172ec, I/O limit 4095Mb (mask 0xffffffff)
hda: 39070080 sectors (20004 MB) w/1768KiB Cache, CHS=2432/255/63, UDMA(100)
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 >
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 113k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Mounted devfs on /dev
Freeing unused kernel memory: 140k freed
Real Time Clock Driver v1.10e
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 22:00:44 Dec 3 2002
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0x1800, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0x1820, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0x1840, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Setting latency timer of device 00:1d.7 to 64
hcd.c: ehci-hcd @ 00:1d.7, Intel Corp. 82801DB USB EHCI Controller
hcd.c: irq 3, pci mem d007b000
usb.c: new USB bus registered, assigned bus number 4
ehci-hcd.c: restricting 64bit DMA mappings to segment 0 ...
ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0
hub.c: USB hub found
hub.c: 6 ports detected
usbdevfs: remount parameter error
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
Adding Swap: 522040k swap-space (priority -1)
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SAMSUNG Model: CDRW/DVD SN-324B Rev: U100
Type: CD-ROM ANSI SCSI revision: 02
ACPI-0323: *** Error: Handler for [Embedded_control] returned AE_BAD_PARAMETER
ACPI-1103: *** Error: Method execution failed, AE_AML_NO_RETURN_VALUE
ACPI-0323: *** Error: Handler for [Embedded_control] returned AE_BAD_PARAMETER
ACPI-1103: *** Error: Method execution failed, AE_BAD_PARAMETER
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Processor [CPU0] (supports C1 C2)
ACPI: Fan [FAN0] (on)
ACPI-0323: *** Error: Handler for [Embedded_control] returned AE_BAD_PARAMETER
ACPI-1103: *** Error: Method execution failed, AE_BAD_PARAMETER
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
MSDOS FS: IO charset iso8859-15
MSDOS FS: Using codepage 850
ohci1394: $Rev: 578 $ Ben Collins <bcollins-8fiUuRrzOP0dnm+yROfE0A@public.gmane.org>
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[d0105000-d01057ff] Max Packet=[2048]
ieee1394: Host added: Node[00:1023] GUID[0000f04120001f68] [Linux OHCI-1394]
hdc: DMA disabled
hda: task_no_data_intr: status=0x51 { DriveReady SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html
eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw-5bpFXmC1L3aJ4eUNlOKu3Q@public.gmane.org> and others
eth0: OEM i82557/i82558 10/100 Ethernet, 00:00:F0:6E:31:1A, IRQ 3.
Board assembly 000000-000, Physical connectors present: RJ45
Primary interface chip i82555 PHY #1.
General self-test: passed.
Serial sub-system self-test: passed.
Internal registers self-test: passed.
ROM checksum self-test: passed (0x04f4518b).
-------------------------------------------------------
This sf.net email is sponsored by:
With Great Power, Comes Great Responsibility
Learn to use your power at OSDN's High Performance Computing Channel
http://hpc.devchannel.org/
reply other threads:[~2002-12-13 17:51 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200212131754.gBDHsmt02104@cnes.fr \
--to=frederic.parrenin-ujc2i/hwirg1lnqxp+/2b1aujnlxr6a1@public.gmane.org \
--cc=acpi-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.