From: Gregoire Favre <greg@ulima.unil.ch>
To: "Justin T. Gibbs" <gibbs@scsiguy.com>
Cc: linux-kernel@vger.kernel.org
Subject: Re: 2.5.54 problem with IDE ICH4 and aic7xxx
Date: Sun, 5 Jan 2003 19:52:27 +0100 [thread overview]
Message-ID: <20030105185227.GA9906@ulima.unil.ch> (raw)
In-Reply-To: <486950000.1041788147@aslan.scsiguy.com>
On Sun, Jan 05, 2003 at 10:35:47AM -0700, Justin T. Gibbs wrote:
> Does the problem persist if you disable domain
> validation via SCSI-Select on your 29160?
Well, I put in http://ulima.unil.ch/greg/linux/2.5.54/dmesg-2.5.54-2
the new result: it's really worse:
aic7xxx: PCI Device 3:3:0 failed memory mapped test. Using PIO.
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.25
<Adaptec 29160B Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
(scsi0:A:0): 80.000MB/s transfers (40.000MHz, offset 15, 16bit)
(scsi1:A:1:0): refuses WIDE negotiation. Using 8bit transfers
(scsi1:A:1): 10.000MB/s transfers (10.000MHz, offset 15)
(scsi1:A:2): 10.000MB/s transfers (10.000MHz, offset 8)
(scsi1:A:3): 10.000MB/s transfers (10.000MHz, offset 8)
(scsi0:A:15): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
scsi0:A:0:0: Tagged Queuing enabled. Depth 253
Vendor: SEAGATE Model: ST336706LW Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:15:0: Tagged Queuing enabled. Depth 253
scsi1 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.25
<Adaptec 2940 Ultra SCSI adapter>
aic7880: Ultra Single Channel A, SCSI Id=7, 16/253 SCBs
scsi1:A:10:0: DV failed to configure device. Please file a bug report against this
driver.
Vendor: TOSHIBA Model: DVD-ROM SD-M1201 Rev: 1R04
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 02
Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 02
SCSI device sda: drive cache: write through
SCSI device sda: 17850000 512-byte hdwr sectors (9139 MB)
/dev/scsi/host0/bus0/target0/lun0: p1 p2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: drive cache: write back
SCSI device sdb: 71687370 512-byte hdwr sectors (36704 MB)
/dev/scsi/host0/bus0/target15/lun0: p1 p2
Attached scsi disk sdb at scsi0, channel 0, id 15, lun 0
sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 1, lun 0
sr1: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr1 at scsi1, channel 0, id 2, lun 0
sr2: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray
Attached scsi CD-ROM sr2 at scsi1, channel 0, id 3, lun 0
device class 'input': registering
register interface 'mouse' with class 'input'
I still have the :
aic7xxx: PCI Device 3:3:0 failed memory mapped test. Using PIO.
But now I have the:
scsi1:A:10:0: DV failed to configure device. Please file a bug report against this driver.
But I don't know what that mean...
cat /proc/scsi/scsi gives me:
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: IBM Model: DDRS-39130D Rev: DC1B
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 15 Lun: 00
Vendor: SEAGATE Model: ST336706LW Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 01 Lun: 00
Vendor: TOSHIBA Model: DVD-ROM SD-M1201 Rev: 1R04
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 02 Lun: 00
Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 03 Lun: 00
Vendor: PLEXTOR Model: CD-R PX-R820T Rev: 1.08
Type: CD-ROM ANSI SCSI revision: 02
Thank you very much,
Grégoire
________________________________________________________________
http://ulima.unil.ch/greg ICQ:16624071 mailto:greg@ulima.unil.ch
next prev parent reply other threads:[~2003-01-05 18:43 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-01-05 16:54 2.5.54 problem with IDE ICH4 and aic7xxx Gregoire Favre
2003-01-05 17:35 ` Justin T. Gibbs
2003-01-05 17:42 ` Gregoire Favre
2003-01-05 18:49 ` Alan Cox
2003-01-05 19:41 ` Gregoire Favre
2003-01-05 20:37 ` Alan Cox
2003-01-05 18:52 ` Gregoire Favre [this message]
2003-01-09 22:56 ` 2.5.54 problem with IDE ICH4 and aic7xxx -> fixed in 2.5.55 Gregoire Favre
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20030105185227.GA9906@ulima.unil.ch \
--to=greg@ulima.unil.ch \
--cc=gibbs@scsiguy.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.