From: Daniel Nash <dan@nash.org>
To: linux-kernel@vger.kernel.org
Subject: Two IDE controller cards dropping DMA mode
Date: Thu, 13 Feb 2003 12:26:13 -0600 [thread overview]
Message-ID: <20030213182613.GF8474@romalar.com> (raw)
I am having trouble setting up a server with two Silicon Image
CMD680 cards (Siig UltraATA 133 PCI). I have one WD2000JB 200GB
hard disk on each of four channels (two per card). When I start
hitting both cards hard by starting RAID 5 on the drives, two of the
four channels have errors and drop DMA mode. After this, the
machine of course performs poorly.
Example:
hdg: dma_intr: status=0x7f { DriveReady DeviceFault SeekComplete
DataRequest CorrectedError Index Error }
hdg: dma_intr: error=0x00 { }
hdg: DMA disabled
ide3: reset: success
This also happens with hda. Swapping things around doesn't change
the problem. If I reset the channel to use UDMA(100) again, the
problem recurs.
I've tried this with 2.4.20 and 2.4.21-pre4-ac4. I would try 2.5.x,
but 59 and 60 and various BK snaps won't boot on my machine.
I've also tried two PDC20269 (Promise Ultra133 TX2) cards in the
same setup, but those would hang the machine when both were in use
at once, no oops, no error messages.
I've tried the kernel config more minimal, with and without APIC and
ACPI and Power Management, and without extras, and there was no
difference. I've tried everything compiled in instead of using some
modules. My current config is at the end of this message.
This is an Athlon 1.46 GHz with an ASUS A7V333 (VIA KT333 chipset)
motherboard. I'm running Debian testing.
Any ideas?
Please CC replies to me.
Thanks for any help,
- Daniel Nash
ver_info:
Linux slic 2.4.21-pre4-ac4 #7 Tue Feb 11 10:12:32 CST 2003 i686 AMD Athlon(TM) XP 1700+ AuthenticAMD GNU/Linux
Gnu C 2.95.4
Gnu make 3.79.1
util-linux 2.11n
mount 2.11n
modutils 2.4.19
e2fsprogs 1.30-WIP
pcmcia-cs 3.1.33
Linux C Library 2.2.5
Dynamic linker (ldd) 2.2.5
Procps 2.0.7
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 4.5.2
Modules Loaded raid5 xor appletalk md
lspci -vvv:
00:00.0 Host bridge: VIA Technologies, Inc. VT8367 [KT266]
Subsystem: Asustek Computer, Inc.: Unknown device 807f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8367 [KT266 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000dfff
Memory behind bridge: dc000000-ddcfffff
Prefetchable memory behind bridge: ddf00000-dfffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:05.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: Asustek Computer, Inc.: Unknown device 80e2
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at d800 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 USB Controller: VIA Technologies, Inc. USB (rev 50) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 8080
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 3
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.1 USB Controller: VIA Technologies, Inc. USB (rev 50) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 8080
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at d000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 51) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 8080
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin C routed to IRQ 10
Region 0: Memory at db800000 (32-bit, non-prefetchable) [disabled] [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0c.0 Unknown mass storage controller: CMD Technology Inc PCI0680 (rev 02)
Subsystem: CMD Technology Inc PCI0680
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 01
Interrupt: pin A routed to IRQ 3
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at b400 [size=4]
Region 2: I/O ports at b000 [size=8]
Region 3: I/O ports at a800 [size=4]
Region 4: I/O ports at a400 [size=16]
Region 5: Memory at db000000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0e.0 Unknown mass storage controller: CMD Technology Inc PCI0680 (rev 02)
Subsystem: CMD Technology Inc PCI0680
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort+ <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 01
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at 9800 [size=4]
Region 2: I/O ports at 9400 [size=8]
Region 3: I/O ports at 9000 [size=4]
Region 4: I/O ports at 8800 [size=16]
Region 5: Memory at da800000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at <unassigned> [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0f.0 Ethernet controller: Linksys Network Everywhere Fast Ethernet 10/100 model NC100 (rev 11)
Subsystem: Linksys: Unknown device 0574
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (16000ns min, 32000ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 8400 [size=256]
Region 1: Memory at da000000 (32-bit, non-prefetchable) [size=1K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233A ISA Bridge
Subsystem: Asustek Computer, Inc.: Unknown device 808c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 808c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at 8000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 23) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 808c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 7
Region 4: I/O ports at 7800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 23) (prog-if 00 [UHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 808c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 7
Region 4: I/O ports at 7400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: nVidia Corporation NV6 [Vanta] (rev 15) (prog-if 00 [VGA])
Subsystem: Micro-star International Co Ltd MSI-8808
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at de000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at ddff0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=31 SBA- 64bit- FW- Rate=x1,x2,x4
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=<none>
dmesg:
hdg: dma_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
hdg: dma_intr: error=0x00 { }
hdg: DMA disabled
ide3: reset: success
hdg: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
hdg: read_intr: error=0x00 { }
ide3: reset: success
hdg: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
hdg: read_intr: error=0x00 { }
ide3: reset: success
hdg: dma_intr: status=0x58 { DriveReady SeekComplete DataRequest }
hdg: CHECK for good STATUS
hda: dma_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
hda: dma_intr: error=0x00 { }
hda: DMA disabled
ide0: reset: success
hda: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
hda: read_intr: error=0x00 { }
ide0: reset: success
hda: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
hda: read_intr: error=0x00 { }
ide0: reset: success
hda: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
hda: read_intr: error=0x00 { }
ide0: reset: success
hda: read_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
hda: read_intr: error=0x00 { }
hdg: dma_intr: status=0x7f { DriveReady DeviceFault SeekComplete DataRequest CorrectedError Index Error }
hdg: dma_intr: error=0x00 { }
hdg: DMA disabled
ide0: reset: success
ide3: reset: success
config:
CONFIG_X86=y
CONFIG_UID16=y
CONFIG_EXPERIMENTAL=y
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
CONFIG_MK7=y
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=6
CONFIG_X86_HAS_TSC=y
CONFIG_X86_GOOD_APIC=y
CONFIG_X86_USE_3DNOW=y
CONFIG_X86_PGE=y
CONFIG_X86_USE_PPRO_CHECKSUM=y
CONFIG_X86_F00F_WORKS_OK=y
CONFIG_X86_MCE=y
CONFIG_X86_CPUID=m
CONFIG_NOHIGHMEM=y
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
CONFIG_X86_TSC=y
CONFIG_NET=y
CONFIG_PCI=y
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_NAMES=y
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
CONFIG_BINFMT_AOUT=y
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=y
CONFIG_IKCONFIG=y
CONFIG_PM=y
CONFIG_PNP=y
CONFIG_BLK_DEV_FD=m
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_RAM=m
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_STATS=y
CONFIG_MD=y
CONFIG_BLK_DEV_MD=m
CONFIG_MD_LINEAR=m
CONFIG_MD_RAID0=m
CONFIG_MD_RAID1=m
CONFIG_MD_RAID5=m
CONFIG_MD_MULTIPATH=m
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_ATALK=m
CONFIG_IDE=y
CONFIG_BLK_DEV_IDE=y
CONFIG_BLK_DEV_IDEDISK=y
CONFIG_IDEDISK_MULTI_MODE=y
CONFIG_BLK_DEV_IDECD=m
CONFIG_BLK_DEV_CMD640=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_CMD64X=y
CONFIG_BLK_DEV_PDC202XX_OLD=y
CONFIG_BLK_DEV_PDC202XX_NEW=y
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_SIIMAGE=y
CONFIG_BLK_DEV_VIA82CXXX=y
CONFIG_IDEDMA_AUTO=y
CONFIG_BLK_DEV_PDC202XX=y
CONFIG_BLK_DEV_IDE_MODES=y
CONFIG_SCSI=m
CONFIG_BLK_DEV_SD=m
CONFIG_SD_EXTRA_DEVS=40
CONFIG_SCSI_DEBUG_QUEUES=y
CONFIG_SCSI_MULTI_LUN=y
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_SYM53C8XX=m
CONFIG_SCSI_NCR53C8XX_DEFAULT_TAGS=4
CONFIG_SCSI_NCR53C8XX_MAX_TAGS=32
CONFIG_SCSI_NCR53C8XX_SYNC=20
CONFIG_NETDEVICES=y
CONFIG_DUMMY=m
CONFIG_NET_ETHERNET=y
CONFIG_NET_PCI=y
CONFIG_TULIP=y
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_MOUSE=y
CONFIG_PSMOUSE=y
CONFIG_AUTOFS4_FS=y
CONFIG_REISERFS_FS=m
CONFIG_HFS_FS=m
CONFIG_EXT3_FS=y
CONFIG_JBD=y
CONFIG_TMPFS=y
CONFIG_RAMFS=y
CONFIG_ISO9660_FS=y
CONFIG_JOLIET=y
CONFIG_PROC_FS=y
CONFIG_DEVPTS_FS=y
CONFIG_EXT2_FS=y
CONFIG_UDF_FS=m
CONFIG_NFS_FS=m
CONFIG_NFS_V3=y
CONFIG_NFSD=m
CONFIG_NFSD_V3=y
CONFIG_SUNRPC=m
CONFIG_LOCKD=m
CONFIG_LOCKD_V4=y
CONFIG_SMB_FS=m
CONFIG_MSDOS_PARTITION=y
CONFIG_SMB_NLS=y
CONFIG_NLS=y
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_VGA_CONSOLE=y
CONFIG_VIDEO_SELECT=y
CONFIG_SOUND=y
CONFIG_SOUND_CMPCI=y
CONFIG_USB=y
CONFIG_USB_UHCI_ALT=y
CONFIG_USB_STORAGE=m
reply other threads:[~2003-02-13 18:16 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20030213182613.GF8474@romalar.com \
--to=dan@nash.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.