From: cb-lkml@fish.zetnet.co.uk
To: linux-kernel@vger.kernel.org
Subject: [2.5.68-mm2] [3c574_cs] irq 11: nobody cared
Date: Wed, 23 Apr 2003 22:49:55 +0100 [thread overview]
Message-ID: <20030423214955.GA602@fish.zetnet.co.uk> (raw)
2.5.68-mm2 gives the following message on ethernet activity. Network appears to
work fine.
lspci -vvv output also follows.
Previously reported problem with APM suspend to disk also still present.
Any more info needed?
Cheers
Charlie
handlers:
[<c8862450>] (el3_interrupt+0x0/0x240 [3c574_cs])
irq 11: nobody cared!
Call Trace:
[<c010b640>] handle_IRQ_event+0x90/0x100
[<c010b897>] do_IRQ+0x97/0x120
[<c0107000>] default_idle+0x0/0x40
[<c0107000>] default_idle+0x0/0x40
[<c0109c68>] common_interrupt+0x18/0x20
[<c0107000>] default_idle+0x0/0x40
[<c0107000>] default_idle+0x0/0x40
[<c0107024>] default_idle+0x24/0x40
[<c01070ba>] cpu_idle+0x3a/0x50
[<c0105000>] _stext+0x0/0x80
[<c02d8755>] start_kernel+0x135/0x140
[<c02d84b0>] unknown_bootoption+0x0/0x120
00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (AGP disabled) (rev 03)
Subsystem: Sony Corporation: Unknown device 805c
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 64
Region 0: Memory at <unassigned> (32-bit, prefetchable) [size=64M]
00:07.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:07.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Region 4: I/O ports at fc90 [size=16]
00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin D routed to IRQ 9
Region 4: I/O ports at fca0 [size=32]
00:07.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 03)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
00:08.0 FireWire (IEEE 1394): Sony Corporation CXD3222 i.LINK Controller (rev 02) (prog-if 10 [OHCI])
Subsystem: Sony Corporation: Unknown device 8060
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fedf7000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fedf7c00 (32-bit, non-prefetchable) [size=512]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: <available only to root>
00:09.0 Multimedia audio controller: Yamaha Corporation YMF-744B [DS-1S Audio Controller] (rev 02)
Subsystem: Sony Corporation: Unknown device 805e
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1250ns min, 6250ns max)
Interrupt: pin A routed to IRQ 9
Region 0: Memory at fedf8000 (32-bit, non-prefetchable) [size=32K]
Region 1: I/O ports at fcc0 [size=64]
Region 2: I/O ports at fc8c [size=4]
Capabilities: <available only to root>
00:0a.0 VGA compatible controller: Neomagic Corporation NM2200 [MagicGraph 256AV] (rev 20) (prog-if 00 [VGA])
Subsystem: Sony Corporation: Unknown device 805d
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 3
Region 0: Memory at fd000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at fe800000 (32-bit, non-prefetchable) [size=4M]
Region 2: Memory at fec00000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <available only to root>
00:0c.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)
Subsystem: Sony Corporation: Unknown device 8061
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168
Interrupt: pin A routed to IRQ 9
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=01, subordinate=04, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001800-000018ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset- 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
next reply other threads:[~2003-04-23 21:37 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-04-23 21:49 cb-lkml [this message]
2003-04-23 23:05 ` [2.5.68-mm2] [3c574_cs] irq 11: nobody cared Andrew Morton
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20030423214955.GA602@fish.zetnet.co.uk \
--to=cb-lkml@fish.zetnet.co.uk \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.