From: Bernd Schubert <bernd-schubert@web.de>
To: linux-smp@vger.kernel.org
Subject: unexpected IO-APIC was found
Date: Wed, 10 Dec 2003 00:28:25 +0100 [thread overview]
Message-ID: <200312100028.25667.bernd-schubert@web.de> (raw)
[-- Attachment #1: Type: text/plain, Size: 497 bytes --]
Hello,
2.4.23 complains abount an unexpected IO-APIC (see that attached
dmesg-output).
The board is an Tyan Thunder K8S (S2880) with only one opteron cpu. Before I
just upgraded the bios to current version those messages didn't occur.
Please cc me since I'm not suscribed to this list.
Cheers,
Bernd
--
Bernd Schubert
Physikalisch Chemisches Institut / Theoretische Chemie
Universität Heidelberg
INF 229
69120 Heidelberg
e-mail: bernd.schubert@pci.uni-heidelberg.de
[-- Attachment #2: dmesg.out --]
[-- Type: text/plain, Size: 12608 bytes --]
MP Tue Dec 9 22:26:02 CET 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007fff0000 (usable)
BIOS-e820: 000000007fff0000 - 000000007ffff000 (ACPI data)
BIOS-e820: 000000007ffff000 - 0000000080000000 (ACPI NVS)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
ACPI: have wakeup address 0xc0002000
found SMP MP-table at 000ff780
hm, page 000ff000 reserved twice.
hm, page 00100000 reserved twice.
hm, page 000f9000 reserved twice.
hm, page 000fa000 reserved twice.
On node 0 totalpages: 524272
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 294896 pages.
ACPI: RSDP (v002 ACPIAM ) @ 0x000f6700
ACPI: XSDT (v001 A M I OEMXSDT 0x10000314 MSFT 0x00000097) @ 0x7fff0100
ACPI: FADT (v001 A M I OEMFACP 0x10000314 MSFT 0x00000097) @ 0x7fff0281
ACPI: MADT (v001 A M I OEMAPIC 0x10000314 MSFT 0x00000097) @ 0x7fff0380
ACPI: OEMB (v001 A M I OEMBIOS 0x10000314 MSFT 0x00000097) @ 0x7ffff040
ACPI: ASF! (v001 AMIASF AMDSTRET 0x00000001 INTL 0x02002026) @ 0x7fff3580
ACPI: DSDT (v001 0ABCF 0ABCF007 0x00000007 INTL 0x02002026) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 Unknown CPU [15:5] APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
Processor #129 invalid (max 16)
ACPI: IOAPIC (id[0x01] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 1
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, IRQ 0-23
ACPI: IOAPIC (id[0x02] address[0xfebfe000] global_irq_base[0x18])
IOAPIC[1]: Assigned apic_id 2
IOAPIC[1]: apic_id 2, version 17, address 0xfebfe000, IRQ 24-27
ACPI: IOAPIC (id[0x03] address[0xfebff000] global_irq_base[0x1c])
IOAPIC[2]: Assigned apic_id 3
IOAPIC[2]: apic_id 3, version 17, address 0xfebff000, IRQ 28-31
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
ACPI BALANCE SET
Using ACPI (MADT) for SMP configuration information
Kernel command line: initrd=pxelinux.cfg/client_initrd.cnfs root=/dev/ram0 rw hdc=ide-scsi apm=power-off BOOT_IMAGE=pxelinux.cfg/client_kernel
ide_setup: hdc=ide-scsi
Initializing CPU#0
Detected 1593.563 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3178.49 BogoMIPS
Memory: 2068068k/2097088k available (1791k kernel code, 28632k reserved, 733k data, 108k init, 1179584k highmem)
Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
Inode cache hash table entries: 131072 (order: 8, 1048576 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 131072 (order: 7, 524288 bytes)
Page-cache hash table entries: 524288 (order: 9, 2097152 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 078bfbff e1d3fbff 00000000 00000000
CPU: Common caps: 078bfbff e1d3fbff 00000000 00000000
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 078bfbff e1d3fbff 00000000 00000000
CPU: Common caps: 078bfbff e1d3fbff 00000000 00000000
CPU0: AMD Opteron(tm) Processor 242 stepping 01
per-CPU timeslice cutoff: 2926.34 usecs.
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000004
ESR value after enabling vector: 00000000
Error: only one processor found.
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 1-0, 1-16, 1-17, 1-18, 1-19, 1-20, 1-21, 1-22, 1-23, 2-0, 2-1, 2-2, 2-3, 3-0, 3-1, 3-2, 3-3 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1593.5740 MHz.
..... host bus clock speed is 199.1968 MHz.
cpu: 0, clocks: 1991968, slice: 995984
CPU0<T0:1991968,T1:995984,D:0,S:995984,C:1991968>
Waiting on wait_init_idle (map = 0x0)
All processors have done init_idle
ACPI: Subsystem revision 20031002
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLA._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.GOLB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
PCI: Probing PCI hardware
IOAPIC[0]: Set PCI routing entry (1-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
00:00:07[A] -> 1-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (1-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1)
00:00:07[B] -> 1-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (1-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1)
00:00:07[C] -> 1-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (1-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1)
00:00:07[D] -> 1-19 -> IRQ 19
Pin 1-19 already programmed
Pin 1-18 already programmed
Pin 1-16 already programmed
Pin 1-17 already programmed
Pin 1-18 already programmed
Pin 1-19 already programmed
Pin 1-17 already programmed
IOAPIC[1]: Set PCI routing entry (2-3 -> 0xc9 -> IRQ 27 Mode:1 Active:1)
00:02:08[A] -> 2-3 -> IRQ 27
IOAPIC[1]: Set PCI routing entry (2-0 -> 0xd1 -> IRQ 24 Mode:1 Active:1)
00:02:08[B] -> 2-0 -> IRQ 24
IOAPIC[1]: Set PCI routing entry (2-1 -> 0xd9 -> IRQ 25 Mode:1 Active:1)
00:02:08[C] -> 2-1 -> IRQ 25
IOAPIC[1]: Set PCI routing entry (2-2 -> 0xe1 -> IRQ 26 Mode:1 Active:1)
00:02:08[D] -> 2-2 -> IRQ 26
Pin 2-2 already programmed
Pin 2-3 already programmed
Pin 2-0 already programmed
Pin 2-1 already programmed
Pin 2-0 already programmed
Pin 2-1 already programmed
Pin 2-0 already programmed
Pin 2-1 already programmed
IOAPIC[2]: Set PCI routing entry (3-0 -> 0xe9 -> IRQ 28 Mode:1 Active:1)
00:01:03[A] -> 3-0 -> IRQ 28
IOAPIC[2]: Set PCI routing entry (3-1 -> 0x32 -> IRQ 29 Mode:1 Active:1)
00:01:03[B] -> 3-1 -> IRQ 29
IOAPIC[2]: Set PCI routing entry (3-2 -> 0x3a -> IRQ 30 Mode:1 Active:1)
00:01:03[C] -> 3-2 -> IRQ 30
IOAPIC[2]: Set PCI routing entry (3-3 -> 0x42 -> IRQ 31 Mode:1 Active:1)
00:01:03[D] -> 3-3 -> IRQ 31
Pin 3-1 already programmed
Pin 3-2 already programmed
Pin 3-3 already programmed
Pin 3-0 already programmed
Pin 3-1 already programmed
Pin 3-2 already programmed
Pin 3-3 already programmed
Pin 3-0 already programmed
Pin 3-2 already programmed
Pin 3-3 already programmed
Pin 3-0 already programmed
Pin 3-1 already programmed
number of MP IRQ sources: 15.
number of IO-APIC #1 registers: 24.
number of IO-APIC #2 registers: 4.
number of IO-APIC #3 registers: 4.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 01000000
....... : arbitration: 01
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 B1
12 001 01 1 1 0 1 0 1 1 B9
13 001 01 1 1 0 1 0 1 1 C1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00030011
....... : max redirection entries: 0003
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@vger.kernel.org
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 1 1 0 1 0 1 1 D1
01 001 01 1 1 0 1 0 1 1 D9
02 001 01 1 1 0 1 0 1 1 E1
03 001 01 1 1 0 1 0 1 1 C9
IO APIC #3......
.... register #00: 03000000
....... : physical APIC id: 03
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00030011
....... : max redirection entries: 0003
An unexpected IO-APIC was found. If this kernel release is less than
three months old please report this to linux-smp@vger.kernel.org
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 1 1 0 1 0 1 1 E9
01 001 01 1 1 0 1 0 1 1 32
02 001 01 1 1 0 1 0 1 1 3A
03 001 01 1 1 0 1 0 1 1 42
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ24 -> 1:0
IRQ25 -> 1:1
IRQ26 -> 1:2
IRQ27 -> 1:3
IRQ28 -> 2:0
IRQ29 -> 2:1
IRQ30 -> 2:2
IRQ31 -> 2:3
.................................... done.
PCI: No IRQ known for interrupt pin A of device 00:0b.0
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: overridden by ACPI.
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1, 8 throttling states)
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Intel(R) PRO/1000 Network Driver - version 5.2.20-k1
Copyright (c) 1999-2003 Intel Corporation.
tg3.c:v2.3 (November 5, 2003)
eth0: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCI:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:52:f1:f1
eth1: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCI:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:52:f1:f0
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[...] (I cut the rest off since it shoudn't be important)
next reply other threads:[~2003-12-09 23:28 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-12-09 23:28 Bernd Schubert [this message]
2003-12-10 1:08 ` unexpected IO-APIC was found Randy.Dunlap
2003-12-10 13:11 ` Bernd Schubert
-- strict thread matches above, loose matches on Subject: below --
2004-01-01 19:01 J and T
2003-12-09 7:04 Unexpected " Pieter Rabe
2003-12-09 16:20 ` Randy.Dunlap
2003-09-22 17:44 unexpected " White, NGH (Nick)
2003-08-08 13:50 Unexpected " Mad Martin
2003-07-15 19:44 Greg Waugh
2003-04-15 8:29 unexpected " Oleg Kivel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200312100028.25667.bernd-schubert@web.de \
--to=bernd-schubert@web.de \
--cc=linux-smp@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.