From: Carlos Puchol <cpg@nospam.rocketmail.com.puchol.com>
To: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Subject: 2.6.0-test11 oops galore: visor sync, cd/dvd burning
Date: Wed, 10 Dec 2003 03:11:51 -0800 [thread overview]
Message-ID: <20031210111151.GA6104@rome.puchol.com> (raw)
hi, i updated a fedora core 1 system with arjanv's kernel
and i keep on getting oopses.
[1.] One line summary of the problem:
multiple oops while transferring a file to a visor connected vis usb.
[2.] Full description of the problem/report:
several attempts to transfer a file into a visor-like device (a treo phone)
yield oopses with 2.6.0-test11. (i also got oopses with dvd+r burning).
it is possible that this is an operator error, where i don't have the right
settings or utilities for a 2.6.-series kernel (though the machine seems to
behave itself reasonably in other circumstance), or where my usb hardware
is not well supported or somesuch.
[3.] Keywords (i.e., modules, networking, kernel):
usb, kernel, visor.
[4.] Kernel version (from /proc/version):
[03:07:49](3)rome:/# cat /proc/version
Linux version 2.6.0-0.test11.1.100 (bhcompile@porky.devel.redhat.com) (gcc version 3.3.2 20031202 (Red Hat Linux 3.3.2-3)) #1 Mon Dec 8 11:17:41 EST 2003
[03:07:51](3)rome:/#
[5.] Output of Oops.. message (if applicable) with symbolic information
resolved (see Documentation/oops-tracing.txt)
Dec 10 02:49:22 rome kernel: hub 2-0:1.0: new USB device on port 1, assigned address 2
Dec 10 02:49:22 rome kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
Dec 10 02:49:22 rome kernel: drivers/usb/core/usb.c: registered new driver usbserial
Dec 10 02:49:22 rome kernel: drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
Dec 10 02:49:22 rome kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS
Dec 10 02:49:22 rome kernel: drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5
Dec 10 02:49:22 rome kernel: usb 2-1: Handspring Visor / Palm OS: Number of ports: 2
Dec 10 02:49:22 rome kernel: usb 2-1: Handspring Visor / Palm OS: port 1, is for Generic use
Dec 10 02:49:22 rome kernel: usb 2-1: Handspring Visor / Palm OS: port 2, is for HotSync use
Dec 10 02:49:22 rome kernel: visor 2-1:1.0: Handspring Visor / Palm OS converter detected
Dec 10 02:49:22 rome kernel: usb 2-1: Handspring Visor / Palm OS converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
Dec 10 02:49:22 rome kernel: usb 2-1: Handspring Visor / Palm OS converter now attached to ttyUSB1 (or usb/tts/1 for devfs)
Dec 10 02:49:22 rome kernel: drivers/usb/core/usb.c: registered new driver visor
Dec 10 02:49:22 rome kernel: drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver v2.1
Dec 10 02:49:23 rome devlabel: devlabel service started/restarted
Dec 10 02:49:27 rome kernel: usb 2-1: USB disconnect, address 2
Dec 10 02:49:27 rome kernel: visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB0
Dec 10 02:49:27 rome kernel: visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB1
Dec 10 02:49:27 rome kernel: visor 2-1:1.0: device disconnected
Dec 10 02:49:28 rome devlabel: devlabel service started/restarted
Dec 10 02:49:28 rome kernel: updfstab: numerical sysctl 1 23 is obsolete.
Dec 10 02:49:28 rome modprobe: FATAL: Module ide_probe_mod not found.
Dec 10 02:49:28 rome modprobe: FATAL: Module ide_probe not found.
Dec 10 02:50:38 rome kernel: hub 2-0:1.0: new USB device on port 1, assigned address 3
Dec 10 02:50:38 rome kernel: usb 2-1: Handspring Visor / Palm OS: Number of ports: 2
Dec 10 02:50:38 rome kernel: usb 2-1: Handspring Visor / Palm OS: port 1, is for Generic use
Dec 10 02:50:38 rome kernel: usb 2-1: Handspring Visor / Palm OS: port 2, is for HotSync use
Dec 10 02:50:38 rome kernel: usbserial 2-1:1.0: Handspring Visor / Palm OS converter detected
Dec 10 02:50:38 rome kernel: usb 2-1: Handspring Visor / Palm OS converter now attached to ttyUSB0 (or usb/tts/0 for devfs)
Dec 10 02:50:38 rome kernel: usb 2-1: Handspring Visor / Palm OS converter now attached to ttyUSB1 (or usb/tts/1 for devfs)
Dec 10 02:50:38 rome usb.agent[4875]: missing kernel or user mode driver visor
Dec 10 02:50:39 rome devlabel: devlabel service started/restarted
Dec 10 02:50:43 rome kernel: usb 2-1: USB disconnect, address 3
Dec 10 02:50:43 rome kernel: usbserial 2-1:1.0: device disconnected
Dec 10 02:50:44 rome devlabel: devlabel service started/restarted
Dec 10 02:50:44 rome kernel: updfstab: numerical sysctl 1 23 is obsolete.
Dec 10 02:50:44 rome modprobe: FATAL: Module ide_probe_mod not found.
Dec 10 02:50:44 rome modprobe: FATAL: Module ide_probe not found.
Dec 10 02:51:13 rome kernel: visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB0
Dec 10 02:51:13 rome kernel: Unable to handle kernel NULL pointer dereference at virtual address 00000024
Dec 10 02:51:13 rome kernel: printing eip:
Dec 10 02:51:13 rome kernel: 0215ca47
Dec 10 02:51:13 rome kernel: *pde = 00000000
Dec 10 02:51:13 rome kernel: Oops: 0002 [#1]
Dec 10 02:51:13 rome kernel: CPU: 0
Dec 10 02:51:13 rome kernel: EIP: 0060:[<0215ca47>] Not tainted
Dec 10 02:51:13 rome kernel: EFLAGS: 00010202
Dec 10 02:51:13 rome kernel: EIP is at simple_rmdir+0x1d/0x33
Dec 10 02:51:13 rome kernel: eax: 00000000 ebx: 20e31190 ecx: 20e31198 edx: ffffffd9
Dec 10 02:51:13 rome kernel: esi: 16036104 edi: 20b237d8 ebp: 20e31190 esp: 080b9d64
Dec 10 02:51:13 rome kernel: ds: 007b es: 007b ss: 0068
Dec 10 02:51:13 rome kernel: Process pilot-xfer (pid: 4863, threadinfo=080b8000 task=098a4ce0)
Dec 10 02:51:13 rome kernel: Stack: 1603616c 16036104 0216fd13 16036104 20e31190 07918714 20e31afc 07918714
Dec 10 02:51:13 rome kernel: 20e31190 00000000 0216fdec 20e31190 19a92748 022e0568 211ba1d0 0218f42c
Dec 10 02:51:14 rome kernel: 19a92748 19a92720 021d4cbd 19a92748 19a92720 229d1f74 19a92720 1f36544c
Dec 10 02:51:14 rome kernel: Call Trace:
Dec 10 02:51:14 rome kernel: [<0216fd13>] remove_dir+0x4d/0x6c
Dec 10 02:51:14 rome kernel: [<0216fdec>] sysfs_remove_dir+0xb8/0xc9
Dec 10 02:51:14 rome kernel: [<0218f42c>] kobject_del+0x46/0x51
Dec 10 02:51:14 rome kernel: [<021d4cbd>] device_del+0x74/0x8b
Dec 10 02:51:14 rome kernel: [<021d4cdf>] device_unregister+0xb/0x16
Dec 10 02:51:14 rome kernel: [<229ccd15>] destroy_serial+0xb9/0x164 [usbserial]
Dec 10 02:51:14 rome kernel: [<0218f4c1>] kobject_cleanup+0x3c/0x54
Dec 10 02:51:14 rome kernel: [<229cc320>] serial_close+0x69/0x7f [usbserial]
Dec 10 02:51:14 rome kernel: [<021b927d>] release_dev+0x1be/0x4bd
Dec 10 02:51:14 rome kernel: [<0213465e>] kmem_cache_free+0x1ea/0x224
Dec 10 02:51:14 rome kernel: [<021b9861>] tty_release+0x9/0xd
Dec 10 02:51:14 rome kernel: [<02145f2a>] __fput+0x37/0xcb
Dec 10 02:51:14 rome kernel: [<02144d4b>] filp_close+0x59/0x62
Dec 10 02:51:14 rome kernel: [<0211c36e>] put_files_struct+0x52/0xa9
Dec 10 02:51:14 rome kernel: [<0211ccf1>] do_exit+0x158/0x290
Dec 10 02:51:14 rome kernel: [<0211ceca>] sys_exit_group+0x0/0x11
Dec 10 02:51:14 rome kernel: [<021238e7>] get_signal_to_deliver+0x2a1/0x2b0
Dec 10 02:51:14 rome kernel: [<0210c303>] do_signal+0x4f/0xbc
Dec 10 02:51:14 rome kernel: [<021348dd>] kfree+0x245/0x27f
Dec 10 02:51:14 rome kernel: [<02153f11>] sys_select+0x45c/0x468
Dec 10 02:51:14 rome kernel: [<02153f11>] sys_select+0x45c/0x468
Dec 10 02:51:14 rome kernel: [<021530ec>] sys_ioctl+0x1f4/0x20c
Dec 10 02:51:14 rome kernel: [<0210c397>] do_notify_resume+0x27/0x38
Dec 10 02:51:14 rome kernel:
Dec 10 02:51:14 rome kernel: Code: ff 48 24 53 56 e8 c5 ff ff ff ff 4e 24 31 d2 5b 5e 5b 89 d0
[6.] A small shell script or example program which triggers the
problem (if possible)
as a user, i was doing this:
pilot-xfer --port /dev/usb/ttyUSB0 --install ~/.addresses/AddressDB.pdb
after issuing a chmod 0666 /dev/usb/ttyUSB0 as root.
[7.] Environment
fedora core 1, with kernel rpm from arjanv, 2.6.0-0.test11.1.100.
[7.1.] Software (add the output of the ver_linux script here)
Linux rome.gwtw.com 2.6.0-0.test11.1.100 #1 Mon Dec 8 11:17:41 EST 2003 i686 athlon i386 GNU/Linux
Gnu C 3.3.2
Gnu make 3.79.1
util-linux 2.11y
mount 2.11y
module-init-tools 2.4.25
e2fsprogs 1.34
jfsutils 1.1.3
reiserfsprogs 3.6.8
pcmcia-cs 3.1.31
quota-tools 3.06.
PPP 2.4.1
isdn4k-utils 3.3
nfs-utils 1.0.6
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Procps 2.0.17
Net-tools 1.60
Kbd 1.08
Sh-utils 5.0
Modules Loaded visor usbserial ide_cd cdrom md5 ipv6 lp autofs e100 ohci1394 ieee1394 floppy parport_pc parport uhci_hcd usbcore thermal processor fan button battery asus_acpi ac ext3 jbd dm_mod
[7.2.] Processor information (from /proc/cpuinfo):
[03:01:13](3)rome:/# cat /proc/cpuinfo
processor : 0
vendor_id : AuthenticAMD
cpu family : 6
model : 8
model name : AMD Athlon(tm) XP 2600+
stepping : 1
cpu MHz : 2083.158
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 mmx fxsr sse syscall mmxext 3dnowext 3dnow
bogomips : 4154.98
[7.3.] Module information (from /proc/modules):
[03:01:16](3)rome:/# cat /proc/modules
visor 14988 0 - Live 0x2298e000
usbserial 26736 3 visor, Live 0x229cc000
ide_cd 36484 0 - Live 0x22973000
cdrom 29856 1 ide_cd, Live 0x2297e000
md5 3840 1 - Live 0x2292f000
ipv6 211520 8 - Live 0x22a09000
lp 10308 0 - Live 0x22937000
autofs 14080 0 - Live 0x22932000
e100 53896 0 - Live 0x2295e000
ohci1394 30600 0 - Live 0x22955000
ieee1394 212780 1 ohci1394, Live 0x22997000
floppy 53972 0 - Live 0x22871000
parport_pc 24872 1 - Live 0x22848000
parport 38248 2 lp,parport_pc, Live 0x2291f000
uhci_hcd 27152 0 - Live 0x22869000
usbcore 94684 5 visor,usbserial,uhci_hcd, Live 0x2293c000
thermal 12816 0 - Live 0x22864000
processor 13860 1 thermal, Live 0x2285f000
fan 3980 0 - Live 0x22833000
button 6168 0 - Live 0x2282a000
battery 9484 0 - Live 0x22844000
asus_acpi 10136 0 - Live 0x22840000
ac 4876 0 - Live 0x2282d000
ext3 112552 4 - Live 0x22881000
jbd 50200 1 ext3, Live 0x22851000
dm_mod 35872 0 - Live 0x22836000
[03:01:36](3)rome:/#
[7.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
[03:01:36](3)rome:/# cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
02f8-02ff : serial
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial
0cf8-0cff : PCI conf1
c000-cfff : PCI Bus #01
c000-c0ff : 0000:01:00.0
d000-d03f : 0000:00:0a.0
d000-d03f : e100
d400-d4ff : 0000:00:0e.0
d800-d81f : 0000:00:10.0
d800-d81f : uhci_hcd
dc00-dc1f : 0000:00:10.1
dc00-dc1f : uhci_hcd
e000-e01f : 0000:00:10.2
e000-e01f : uhci_hcd
e400-e40f : 0000:00:11.1
e400-e407 : ide0
e408-e40f : ide1
[03:01:55](3)rome:/# cat /proc/iomem
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000d0000-000d17ff : Extension ROM
000f0000-000fffff : System ROM
00100000-1ffeffff : System RAM
00100000-00261fff : Kernel code
00262000-00313bff : Kernel data
1fff0000-1fff2fff : ACPI Non-volatile Storage
1fff3000-1fffffff : ACPI Tables
d0000000-dfffffff : PCI Bus #01
d0000000-d7ffffff : 0000:01:00.0
d8000000-dfffffff : 0000:01:00.1
e0000000-e3ffffff : 0000:00:00.0
e4000000-e40fffff : PCI Bus #01
e4020000-e402ffff : 0000:01:00.0
e4030000-e403ffff : 0000:01:00.1
e4100000-e411ffff : 0000:00:0a.0
e4100000-e411ffff : e100
e4130000-e4130fff : 0000:00:0a.0
e4130000-e4130fff : e100
e4131000-e4131fff : 0000:00:0b.0
e4132000-e4132fff : 0000:00:0b.1
e4133000-e41330ff : 0000:00:10.3
fec00000-fec00fff : reserved
fee00000-fee00fff : reserved
ffff0000-ffffffff : reserved
[03:02:02](3)rome:/#
[7.5.] PCI information ('lspci -vvv' as root)
[03:02:02](3)rome:/# lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge
Subsystem: VIA Technologies, Inc. VT8377 [KT400 AGP] Host Bridge
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4
Command: RQ=31 SBA- AGP- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e4000000-e40fffff
Prefetchable memory behind bridge: d0000000-dfffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 0c)
Subsystem: Intel Corp. EtherExpress PRO/100 S Desktop Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e4130000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at d000 [size=64]
Region 2: Memory at e4100000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at <unassigned> [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
00:0b.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 02)
Subsystem: STB Systems Inc: Unknown device 2636
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (4000ns min, 10000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e4131000 (32-bit, prefetchable) [size=4K]
00:0b.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 02)
Subsystem: STB Systems Inc: Unknown device 2636
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at e4132000 (32-bit, prefetchable) [size=4K]
00:0e.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: Soyo Computer, Inc: Unknown device a715
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at d400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at dc00 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
00:10.2 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin C routed to IRQ 10
Region 4: I/O ports at e000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 5
Region 0: Memory at e4133000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc. VT8235 ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at e400 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R250 If [Radeon 9000] (rev 01) (prog-if 00 [VGA])
Subsystem: PC Partner Limited R250 If [Radeon 9000 "Atlantis"]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at c000 [size=256]
Region 2: Memory at e4020000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW+ Rate=x1,x2,x4
Command: RQ=0 SBA+ AGP- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.1 Display controller: ATI Technologies Inc Radeon R250 [Radeon 9000] (Secondary) (rev 01)
Subsystem: PC Partner Limited: Unknown device 7193
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Region 0: Memory at d8000000 (32-bit, prefetchable) [disabled] [size=128M]
Region 1: Memory at e4030000 (32-bit, non-prefetchable) [disabled] [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
[03:02:27](3)rome:/#
[7.6.] SCSI information (from /proc/scsi/scsi)
[03:02:27](3)rome:/# cat /proc/scsi/scsi
cat: /proc/scsi/scsi: No such file or directory
[03:02:59](3)rome:/#
[7.7.] Other information that might be relevant to the problem
(please look in /proc and include all information that you
think to be relevant):
it is possible that this is a user error, since i am not sure
[X.] Other notes, patches, fixes, workarounds:
under 2.6.0-test4, i got this under similar visor-related circumstances:
Dec 10 01:03:22 rome kernel: Slab corruption: start=cd7fd8b4, expend=cd7fdab3, problemat=cd7fd8bc
Dec 10 01:03:22 rome kernel: Last user: [<c01fb618>](device_release+0x58/0x60)
Dec 10 01:03:22 rome kernel: Data: ********00 00 00 00 *******************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************************A5
Dec 10 01:03:22 rome kernel: Next: 71 F0 2C .18 B6 1F C0 71 F0 2C .********************
Dec 10 01:03:22 rome kernel: slab error in check_poison_obj(): cache `size-512': object was modified after freeing
Dec 10 01:03:22 rome kernel: Call Trace:
Dec 10 01:03:22 rome kernel: [<c013c588>] check_poison_obj+0x168/0x1b0
Dec 10 01:03:22 rome kernel: [<c013dd93>] __kmalloc+0x153/0x1c0
Dec 10 01:03:22 rome kernel: [<c024a3e7>] alloc_skb+0x47/0xe0
Dec 10 01:03:22 rome kernel: [<c024a3e7>] alloc_skb+0x47/0xe0
Dec 10 01:03:22 rome kernel: [<c0249c1d>] sock_alloc_send_pskb+0xbd/0x1c0
Dec 10 01:03:22 rome kernel: [<c0249d4f>] sock_alloc_send_skb+0x2f/0x40
Dec 10 01:03:22 rome kernel: [<c02a5aa6>] unix_stream_sendmsg+0x186/0x3c0
Dec 10 01:03:22 rome kernel: [<c0246b02>] sock_sendmsg+0xc2/0xd0
Dec 10 01:03:22 rome kernel: [<c0139df2>] buffered_rmqueue+0xb2/0x140
Dec 10 01:03:22 rome kernel: [<c0111120>] convert_fxsr_to_user+0xc0/0x160
Dec 10 01:03:22 rome kernel: [<c01a2266>] avc_has_perm+0x76/0x8c
Dec 10 01:03:22 rome kernel: [<c0246edd>] sock_readv_writev+0x7d/0xb0
Dec 10 01:03:22 rome kernel: [<c0246fbf>] sock_writev+0x4f/0x60
Dec 10 01:03:22 rome kernel: [<c0152c6f>] do_readv_writev+0x25f/0x2c0
Dec 10 01:03:22 rome kernel: [<c01114a4>] restore_i387_fxsave+0x84/0x90
Dec 10 01:03:22 rome kernel: [<c011152a>] restore_i387+0x7a/0x80
Dec 10 01:03:22 rome kernel: [<c0152d93>] vfs_writev+0x53/0x60
Dec 10 01:03:22 rome kernel: [<c0152e52>] sys_writev+0x42/0x70
Dec 10 01:03:22 rome kernel: [<c010a9bb>] syscall_call+0x7/0xb
i also notice that i get various oopses burning a dvd+r.
(sorry did not get the oops info - this one is not fun to reproduce,
since it seems to waste a dvd+r)
next reply other threads:[~2003-12-10 11:11 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-12-10 11:11 Carlos Puchol [this message]
2003-12-11 8:51 ` 2.6.0-test11 oops galore: visor sync, cd/dvd burning Greg KH
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20031210111151.GA6104@rome.puchol.com \
--to=cpg@nospam.rocketmail.com.puchol.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.