------------ mkinitrd ----------
# mkinitrd -v --lvm-version=2 -f /boot/initrd-2.4.24-0.pre2.1mdk.img 2.4.24-0.pre2.1mdk
Looking for deps of module 3w-xxxx
	 scsi_mod
Looking for deps of module scsi_mod
Looking for deps of module sd_mod
	 scsi_mod
Looking for deps of module scsi_mod
Looking for deps of module dm-mod
Looking for deps of module ext3
	 jbd
Looking for deps of module jbd
Using modules:  ./kernel/drivers/scsi/scsi_mod.o ./kernel/drivers/scsi/3w-xxxx.o ./kernel/drivers/scsi/sd_mod.o ./kernel/drivers/md/dm-mod.o ./kernel/fs/jbd/jbd.o ./kernel/fs/ext3/ext3.o
Using /root/tmp as temporary directory.
/sbin/nash -> /root/tmp/initrd.02YkRu/bin/nash
/sbin/insmod-DIET -> /root/tmp/initrd.02YkRu/bin/insmod
Loading module scsi_mod.o
Loading module 3w-xxxx.o
Loading module sd_mod.o
Loading module dm-mod.o
Loading module jbd.o
Loading module ext3.o
`/sbin/lvm2-static' -> `/root/tmp/initrd.02YkRu/sbin/vgscan'
Contents of RCFILE:
#!/bin/nash

echo "Loading scsi_mod.o module"
insmod /lib/scsi_mod.o 
echo "Loading 3w-xxxx.o module"
insmod /lib/3w-xxxx.o 
echo "Loading sd_mod.o module"
insmod /lib/sd_mod.o 
echo "Loading dm-mod.o module"
insmod /lib/dm-mod.o 
echo "Loading jbd.o module"
insmod /lib/jbd.o 
echo "Loading ext3.o module"
insmod /lib/ext3.o 
echo Mounting /proc filesystem
mount -t proc /proc /proc
echo Creating device files
mkdevices /dev
echo Making device-mapper control node
mkdmnod
echo Scanning logical volumes
vgscan --ignorelockingfailure
echo Activating logical volumes
vgchange -ay --ignorelockingfailure
echo Making device nodes
vgmknodes
echo 0x0100 > /proc/sys/kernel/real-root-dev
echo Mounting root filesystem 
mount -o defaults --ro -t ext3 /dev/vg00/lvol1 /sysroot
pivot_root /sysroot /sysroot/initrd
echo Remounting devfs at correct place if necessary
handledevfs
umount /initrd/proc
Creating filesystem with size 978KB and 147 inodes

------------ lilo.conf ---------
boot=/dev/sda
map=/boot/map
install=menu
vga=792
default="linux"
keytable=/boot/us.klt
prompt
nowarn
timeout=100
message=/boot/message
menu-scheme=wb:bw:wb:bw
image=/boot/vmlinuz
	label=linux
	root=/dev/vg00/lvol1
	initrd=/boot/initrd.img
	append="panic=60 acpi=force devfs=mount"
	read-only

------------ boot log ----------
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 333k freed
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Red Hat nash version 3.5.15.1-mdk starting
Loading scsi_mod.o module
Using insmod provided by busybox.
SCSI subsystem driver Revision: 1.00
Loading 3w-xxxx.o module
Using insmod provided by busybox.
3ware Storage Controller device driver for Linux v1.02.00.037.
scsi0 : Found a 3ware Storage Controller at 0x7c30, IRQ: 9, P-chip: 1.3
scsi0 : 3ware Storage Controller
  Vendor: 3ware     Model: Logical Disk 0    Rev: 1.0
  Type:   Direct-Access                      ANSI SCSI revision: 00
Loading sd_mod.o module
Using insmod provided by busybox.
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 240119680 512-byte hdwr sectors (122941 MB)
Partition check:
 /dev/scsi/host0/bus0/target0/lun0: p1
Loading dm-mod.o module
Using insmod provided by busybox.
device-mapper: 4.0.1-ioctl (2003-07-12) initialised: dm@uk.sistina.com
Loading jbd.o module
Using insmod provided by busybox.
Journalled Block Device driver loaded
Loading ext3.o module
Using insmod provided by busybox.
Mounting /proc filesystem
Creating device files
Making device-mapper control node
failed to create /dev/mapper/control
Scanning logical volumes
  Reading all physical volumes.  This may take a while...
  Found volume group "vg00" using metadata type lvm1
Activating logical volumes
  7 logical volume(s) in volume group "vg00" now active
Making device nodes
Mounting root filesystem
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Remounting devfs at correct place if necessary
Mounted devfs on /dev
Freeing unused kernel memory: 156k freed
INIT: version 2.85 booting