From: Helge Deller <deller@gmx.de>
To: linux-kernel@vger.kernel.org
Subject: Re: Linux 2.6.5-rc3 - ALI15X3, irq 15: nobody cared! / Disabling IRQ #15
Date: Tue, 30 Mar 2004 21:40:23 +0200 [thread overview]
Message-ID: <200403302140.23791.deller@gmx.de> (raw)
In-Reply-To: <Pine.LNX.4.58.0403292129200.1096@ppc970.osdl.org>
IBM R30 Laptop, ALI15X3 IDE onboard chip, internal IDE harddisk & CDROM gives
irq 15: nobody cared!
....
Disabling IRQ #15
Message repeats ~ 1/min.
00:10.0 IDE interface: ALi Corporation M5229 IDE (rev c3) (prog-if fa)
Subsystem: IBM: Unknown device 050f
Flags: bus master, medium devsel, latency 32, IRQ 15
I/O ports at 7050 [size=16]
Capabilities: [60] Power Management version 2
Any ideas ?
<4>Linux version 2.6.5-rc3 (root@halden) (gcc version 3.3.1 (SuSE Linux)) #2 Tue Mar 30 10:28:34 CEST 2004
<6>BIOS-provided physical RAM map:
<4> BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
<4> BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
<4> BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
<4> BIOS-e820: 0000000000100000 - 000000000f7e0000 (usable)
<4> BIOS-e820: 000000000f7e0000 - 000000000f7f0000 (reserved)
<4> BIOS-e820: 000000000f7f0000 - 000000000f7f8000 (ACPI data)
<4> BIOS-e820: 000000000f7f8000 - 000000000f800000 (ACPI NVS)
<4> BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
<5>247MB LOWMEM available.
<4>On node 0 totalpages: 63456
<4> DMA zone: 4096 pages, LIFO batch:1
<4> Normal zone: 59360 pages, LIFO batch:14
<4> HighMem zone: 0 pages, LIFO batch:1
<6>DMI 2.3 present.
<6>IBM machine detected. Enabling interrupts during APM calls.
<6>IBM machine detected. Disabling SMBus accesses.
<6>ACPI: RSDP (v000 IBM ) @ 0x000fe030
<6>ACPI: RSDT (v001 IBM TP-1C 0x00001320 IBM 0x00000000) @ 0x0f7f0000
<6>ACPI: FADT (v001 IBM TP-1C 0x00001320 IBM 0x00000000) @ 0x0f7f0054
<6>ACPI: BOOT (v001 IBM TP-1C 0x00001320 IBM 0x00000000) @ 0x0f7f002c
<6>ACPI: DSDT (v001 IBM TP-1C 0x00001320 MSFT 0x0100000d) @ 0x00000000
<6>ACPI: PM-Timer IO Port: 0xf108
<4>Built 1 zonelists
<4>Kernel command line: root=/dev/hda2 pmdisk=/dev/hda3
<4>Local APIC disabled by BIOS -- reenabling.
<4>Could not enable APIC!
<6>Initializing CPU#0
<4>PID hash table entries: 1024 (order 10: 8192 bytes)
<4>Detected 697.812 MHz processor.
<6>Using pmtmr for high-res timesource
<4>Console: colour VGA+ 80x25
<6>Memory: 247704k/253824k available (1687k kernel code, 5388k reserved, 720k data, 168k init, 0k highmem)
<4>Checking if this processor honours the WP bit even in supervisor mode... Ok.
<4>Calibrating delay loop... 1384.44 BogoMIPS
<6>Security Scaffold v1.0.0 initialized
<6>Capability LSM initialized
<6>Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
<4>Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
<4>Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
<7>CPU: After generic identify, caps: 0383f9ff 00000000 00000000 00000000
<7>CPU: After vendor identify, caps: 0383f9ff 00000000 00000000 00000000
<6>CPU: L1 I cache: 16K, L1 D cache: 16K
<6>CPU: L2 cache: 256K
<7>CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040
<6>Intel machine check architecture supported.
<6>Intel machine check reporting enabled on CPU#0.
<4>CPU: Intel Pentium III (Coppermine) stepping 0a
<6>Enabling fast FPU save and restore... done.
<6>Enabling unmasked SIMD FPU exception support... done.
<6>Checking 'hlt' instruction... OK.
<4>POSIX conformance testing by UNIFIX
<6>NET: Registered protocol family 16
<6>PCI: PCI BIOS revision 2.10 entry at 0xf0200, last bus=1
<6>PCI: Using configuration type 1
<6>mtrr: v2.0 (20020519)
<6>ACPI: Subsystem revision 20040326
<4>ACPI: IRQ9 SCI: Edge Trigger.
<6>ACPI: Interpreter enabled
<6>ACPI: Using PIC for interrupt routing
<4>ACPI: PCI Interrupt Link [PILA] (IRQs 1 3 4 5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [PILB] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
<4>ACPI: PCI Interrupt Link [PILC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [PILD] (IRQs 10 *11)
<4>ACPI: PCI Interrupt Link [PILE] (IRQs 1 3 4 5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [PILF] (IRQs 1 3 4 5 6 7 10 11 12 14 15)
<4>ACPI: PCI Interrupt Link [PILG] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
<4>ACPI: PCI Interrupt Link [PILH] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
<4>ACPI: PCI Interrupt Link [PILI] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
<6>ACPI: PCI Root Bridge [PCI0] (00:00)
<4>PCI: Probing PCI hardware (bus 00)
<7>ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
<6>ACPI: Embedded Controller [EC0] (gpe 34)
<6>Linux Plug and Play Support v0.97 (c) Adam Belay
<6>PnPBIOS: Scanning system for PnP BIOS support...
<6>PnPBIOS: Found PnP BIOS installation structure at 0xc00f6f40
<6>PnPBIOS: PnP BIOS version 1.0, entry 0xfa000:0x0, dseg 0xf0000
<3>PnPBIOS: dev_node_info: function not supported on this system
<3>PnPBIOS: Unable to get node info. Aborting.
<4>ACPI: PCI Interrupt Link [PILH] enabled at IRQ 11
<4>ACPI: PCI Interrupt Link [PILB] enabled at IRQ 11
<4>ACPI: PCI Interrupt Link [PILD] enabled at IRQ 11
<4>ACPI: PCI Interrupt Link [PILI] enabled at IRQ 10
<6>PCI: Using ACPI for IRQ routing
<6>PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
<6>Simple Boot Flag at 0x41 set to 0x1
<6>Machine check exception polling timer started.
<6>cpufreq: Intel(R) SpeedStep(TM) for this chipset not (yet) available.
<6>ikconfig 0.7 with /proc/config*
<6>Initializing Cryptographic API
<6>Activating ISA DMA hang workarounds.
<6>isapnp: Scanning for PnP cards...
<6>isapnp: No Plug & Play device found
<6>Real Time Clock Driver v1.12
<6>loop: loaded (max 8 devices)
<6>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
<6>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
<6>ALI15X3: IDE controller at PCI slot 0000:00:10.0
<6>ALI15X3: chipset revision 195
<6>ALI15X3: not 100%% native mode: will probe irqs later
<6> ide0: BM-DMA at 0x7050-0x7057, BIOS settings: hda:DMA, hdb:pio
<6> ide1: BM-DMA at 0x7058-0x705f, BIOS settings: hdc:DMA, hdd:pio
<4>hda: HITACHI_DK23CA-30, ATA DISK drive
<4>Using anticipatory io scheduler
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>hdc: MATSHITADVD-ROM SR-8176, ATAPI CD/DVD-ROM drive
<3>irq 15: nobody cared!
<4>Call Trace:
<4> [<c0109c74>] __report_bad_irq+0x24/0x90
<4> [<c0109fd7>] do_IRQ+0x177/0x1f0
<4> [<c0107cc8>] common_interrupt+0x18/0x20
<4> [<c0123cbd>] do_softirq+0x3d/0xa0
<4> [<c0109fca>] do_IRQ+0x16a/0x1f0
<4> [<c0107cc8>] common_interrupt+0x18/0x20
<4> [<c010961e>] setup_irq+0x7e/0xe0
<4> [<c021e830>] ide_intr+0x0/0x260
<4> [<c0109bff>] request_irq+0x8f/0xe0
<4> [<c02217b2>] init_irq+0x1c2/0x5a0
<4> [<c021e830>] ide_intr+0x0/0x260
<4> [<c01bf3a7>] vsprintf+0x27/0x30
<4> [<c0221cd5>] hwif_init+0x145/0x380
<4> [<c0223029>] probe_hwif_init+0x19/0x66
<4> [<c0226768>] ide_setup_pci_device+0x68/0x80
<4> [<c021437b>] alim15x3_init_one+0x4b/0x80
<4> [<c0374d84>] ide_scan_pcidev+0x54/0x80
<4> [<c0374dce>] ide_scan_pcibus+0x1e/0xb0
<4> [<c0374d1a>] ide_init+0x5a/0x70
<4> [<c01030e8>] init+0x58/0x1d0
<4> [<c0103090>] init+0x0/0x1d0
<4> [<c0105005>] kernel_thread_helper+0x5/0x10
<4>
<3>handlers:
<3>[<c021e830>] (ide_intr+0x0/0x260)
<0>Disabling IRQ #15
<4>ide1 at 0x170-0x177,0x376 on irq 15
<4>hda: max request size: 128KiB
<6>hda: 58605120 sectors (30005 MB) w/2048KiB Cache, CHS=58140/16/63, UDMA(33)
<6> hda: hda1 hda2 hda3 hda4 < hda5 hda6 >
<6>mice: PS/2 mouse device common for all mice
next prev parent reply other threads:[~2004-03-30 19:42 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-03-30 5:35 Linux 2.6.5-rc3 Linus Torvalds
2004-03-30 5:54 ` Ivan Gyurdiev
2004-03-30 6:03 ` Ivan Gyurdiev
2004-03-30 15:26 ` Greg KH
2004-03-30 6:14 ` Dominik Karall
2004-03-30 8:26 ` Marc-Christian Petersen
2004-03-30 12:37 ` Felipe Alfaro Solana
2004-03-30 14:07 ` Ivan Gyurdiev
2004-03-30 14:34 ` Lenar Lõhmus
2004-03-30 6:50 ` Linux 2.6.5-rc3 [ACPI error message] Dumitru Ciobarcianu
2004-03-30 16:04 ` Linux 2.6.5-rc3 (compile stats) John Cherry
2004-03-30 19:40 ` Helge Deller [this message]
[not found] <A6974D8E5F98D511BB910002A50A6647615F6E02@hdsmsx402.hd.intel.com>
2004-03-31 17:25 ` Linux 2.6.5-rc3 - ALI15X3, irq 15: nobody cared! / Disabling IRQ #15 Len Brown
2004-03-31 21:38 ` Helge Deller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200403302140.23791.deller@gmx.de \
--to=deller@gmx.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.