From: Antonin Kral <A.Kral@sh.cvut.cz>
To: linux-kernel@vger.kernel.org
Subject: Re: AIC79xx problem
Date: Sun, 11 Jul 2004 15:12:24 +0200 [thread overview]
Message-ID: <20040711131224.GA13575@sh.cvut.cz> (raw)
In-Reply-To: <20040711061351.GA4190@sh.cvut.cz>
Hi all,
> I've checked that the problem is closely releated to AIC79xx, because it
> raises when I use SCSI. I've got some old IDE disk and with it work
> everything perfectly.
I still have problems with AIC79xx driver, but I've finally got some
kernel outputs. Problems seem to araise only during writing to the disk.
When I install system to the same disk at other computer, I can run
programs without problem, but during writing to the disk I receive a lot
of messages similar to these:
scsi1: PCI error Interrupt
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State at program address 0xe Mode 0x33
Card was paused
HS_MAILBOX[0x0] INTCTL[0x80] SEQINTSTAT[0x0] SAVED_MODE[0x11]
DFFSTAT[0x1] SCSISIGI[0x24] SCSIPHASE[0x1] SCSIBUS[0x94]
LASTPHASE[0x1] SCSISEQ0[0x0] SCSISEQ1[0x12] SEQCTL0[0x10]
SEQINTCTL[0x8] SEQ_FLAGS[0xc0] SEQ_FLAGS2[0x0] SSTAT0[0x0]
SSTAT1[0x19] SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4] LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0]
LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x81]
SCB Count = 30 CMDS_PENDING = 2 LASTSCB 0x6 CURRSCB 0x1d NEXTSCB 0xff00
qinstart = 1103 qinfifonext = 1103
QINFIFO:
WAITING_TID_QUEUES:
Pending list:
29 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x37]
6 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x37]
Total 2
Kernel Free SCB list: 21 28 4 17 27 24 20 16 23 22 3 2 1 5 14 13 12 11 0 9 8 7 19 15 18 10 26 25
Sequencer Complete DMA-inprog list:
Sequencer Complete list:
Sequencer DMA-Up and Complete list:
scsi1: FIFO0 Active, LONGJMP == 0x80ff, SCB 0x6
SEQIMODE[0x3f] SEQINTSRC[0x20] DFCNTRL[0x0] DFSTATUS[0x89]
SG_CACHE_SHADOW[0x38] SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x7e] MDFFSTAT[0xc] SHADDR = 0x0361cb000, SHCNT = 0x1000
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x0]
scsi1: FIFO1 Active, LONGJMP == 0x257, SCB 0x6
SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x2c] DFSTATUS[0xc9]
SG_CACHE_SHADOW[0x38] SG_STATE[0x3] DFFSXFRCTL[0x0]
SOFFCNT[0x7e] MDFFSTAT[0x2] SHADDR = 0x0361cc000, SHCNT = 0x0
HADDR = 0x0361cc000, HCNT = 0x0 CCSGCTL[0x10]
LQIN: 0x5 0x0 0x0 0x6 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x80 0x0 0x0 0x0 0x2 0x0
scsi1: LQISTATE = 0x25, LQOSTATE = 0x0, OPTIONMODE = 0x42
scsi1: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x3
SIMODE0[0xc]
CCSCBCTL[0x0]
scsi1: REG0 == 0x15, SINDEX = 0x133, DINDEX = 0x108
scsi1: SCBPTR == 0x15, SCB_NEXT == 0x6, SCB_NEXT2 == 0xffe4
CDB 0 10 0 80 60 96
STACK: 0x125 0x0 0x0 0x25e 0x257 0x257 0x29 0x1
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
DevQ(0:3:0): 0 waiting
DevQ(0:6:0): 0 waiting
scsi1: Split completion read data parity error in DFF1
scsi1: Address or Write Phase Parity Error Detected in DFF1.
scsi1: PCI error Interrupt
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State at program address 0x27 Mode 0x22
Card was paused
HS_MAILBOX[0x0] INTCTL[0x80] SEQINTSTAT[0x0] SAVED_MODE[0x11]
DFFSTAT[0x11] SCSISIGI[0x24] SCSIPHASE[0x1] SCSIBUS[0x95]
LASTPHASE[0x1] SCSISEQ0[0x0] SCSISEQ1[0x12] SEQCTL0[0x10]
SEQINTCTL[0x0] SEQ_FLAGS[0xc0] SEQ_FLAGS2[0x0] SSTAT0[0x0]
SSTAT1[0x19] SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4] LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0]
LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x81]
SCB Count = 30 CMDS_PENDING = 2 LASTSCB 0x6 CURRSCB 0x1d NEXTSCB 0xff00
qinstart = 1103 qinfifonext = 1103
QINFIFO:
WAITING_TID_QUEUES:
Pending list:
29 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x37]
6 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x37]
Total 2
Kernel Free SCB list: 21 28 4 17 27 24 20 16 23 22 3 2 1 5 14 13 12 11 0 9 8 7 19 15 18 10 26 25
Sequencer Complete DMA-inprog list:
Sequencer Complete list:
Sequencer DMA-Up and Complete list:
scsi1: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x6
SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]
SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x7e] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x0]
scsi1: FIFO1 Active, LONGJMP == 0x257, SCB 0x6
SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x2c] DFSTATUS[0xc9]
SG_CACHE_SHADOW[0x28] SG_STATE[0x3] DFFSXFRCTL[0x0]
SOFFCNT[0x7e] MDFFSTAT[0x2] SHADDR = 0x0361ad000, SHCNT = 0x0
HADDR = 0x0361ad000, HCNT = 0x0 CCSGCTL[0x10]
LQIN: 0x5 0x0 0x0 0x6 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x80 0x0 0x0 0x0 0x2 0x0
scsi1: LQISTATE = 0x25, LQOSTATE = 0x0, OPTIONMODE = 0x42
scsi1: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x3
SIMODE0[0xc]
CCSCBCTL[0x0]
scsi1: REG0 == 0x1d, SINDEX = 0x122, DINDEX = 0x108
scsi1: SCBPTR == 0x15, SCB_NEXT == 0x6, SCB_NEXT2 == 0xffe4
CDB 0 10 0 80 60 96
STACK: 0x15 0x125 0x0 0x0 0x25e 0x257 0x93 0x29
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
DevQ(0:3:0): 0 waiting
DevQ(0:6:0): 0 waiting
scsi1: Split completion read data parity error in DFF1
scsi1: Address or Write Phase Parity Error Detected in DFF1.
scsi1: PCI error Interrupt
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
scsi1: Dumping Card State at program address 0x93 Mode 0x11
Card was paused
HS_MAILBOX[0x0] INTCTL[0x80] SEQINTSTAT[0x0] SAVED_MODE[0x11]
DFFSTAT[0x11] SCSISIGI[0x24] SCSIPHASE[0x1] SCSIBUS[0x95]
LASTPHASE[0x1] SCSISEQ0[0x0] SCSISEQ1[0x12] SEQCTL0[0x10]
SEQINTCTL[0x0] SEQ_FLAGS[0xc0] SEQ_FLAGS2[0x0] SSTAT0[0x0]
SSTAT1[0x19] SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4] LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0]
LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x81]
SCB Count = 30 CMDS_PENDING = 2 LASTSCB 0x6 CURRSCB 0x6 NEXTSCB 0xffc0
qinstart = 1120 qinfifonext = 1120
QINFIFO:
WAITING_TID_QUEUES:
Pending list:
6 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x37]
20 FIFO_USE[0x0] SCB_CONTROL[0x60] SCB_SCSIID[0x37]
Total 2
Kernel Free SCB list: 24 27 17 4 28 21 29 16 23 22 3 2 1 5 14 13 12 11 0 9 8 7 19 15 18 10 26 25
Sequencer Complete DMA-inprog list:
Sequencer Complete list:
Sequencer DMA-Up and Complete list:
scsi1: FIFO0 Free, LONGJMP == 0x80ff, SCB 0x18
SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]
SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x7e] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x0]
scsi1: FIFO1 Active, LONGJMP == 0x257, SCB 0x14
SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x2c] DFSTATUS[0xc9]
SG_CACHE_SHADOW[0x28] SG_STATE[0x3] DFFSXFRCTL[0x0]
SOFFCNT[0x7e] MDFFSTAT[0x2] SHADDR = 0x036461000, SHCNT = 0x0
HADDR = 0x036461000, HCNT = 0x0 CCSGCTL[0x10]
LQIN: 0x5 0x0 0x0 0x14 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x80 0x0 0x0 0x0 0x2 0x0
scsi1: LQISTATE = 0x25, LQOSTATE = 0x0, OPTIONMODE = 0x42
scsi1: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
SIMODE0[0xc]
CCSCBCTL[0x0]
scsi1: REG0 == 0x60, SINDEX = 0x122, DINDEX = 0x108
scsi1: SCBPTR == 0x14, SCB_NEXT == 0xffc0, SCB_NEXT2 == 0xffe4
CDB 2a 0 0 0 28 90
STACK: 0x29 0x15 0x125 0x0 0x0 0x257 0x257 0x257
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
DevQ(0:3:0): 0 waiting
DevQ(0:6:0): 0 waiting
scsi1: Split completion read data parity error in DFF1
scsi1: Address or Write Phase Parity Error Detected in DFF1.
I've found some info, that this could be releated to the firmware
version on the disk (
http://lists.freebsd.org/pipermail/aic7xxx/2004-February/004083.html ).
So output from the /proc/scsi/scsi:
Attached devices:
Host: scsi0 Channel: 00 Id: 06 Lun: 00
Vendor: SUPER Model: GEM318 Rev: 0
Type: Processor ANSI SCSI revision: 02
Host: scsi1 Channel: 00 Id: 03 Lun: 00
Vendor: SEAGATE Model: ST373453LC Rev: 0006
Type: Direct-Access ANSI SCSI revision: 03
Host: scsi1 Channel: 00 Id: 06 Lun: 00
Vendor: SUPER Model: GEM318 Rev: 0
Type: Processor ANSI SCSI revision: 02
Any idea? I will appreciate any help, thaks
Antonin
next prev parent reply other threads:[~2004-07-11 13:12 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <A6974D8E5F98D511BB910002A50A6647615FFBBF@hdsmsx403.hd.intel.com>
2004-07-11 2:30 ` Fatal problem, possibly related to AIC79xx Len Brown
2004-07-11 6:13 ` AIC79xx problem [was; Re: Fatal problem, possibly related to AIC79xx] Antonin Kral
2004-07-11 13:12 ` Antonin Kral [this message]
2003-06-12 21:39 aic79xx problem Russell Miller
2003-06-12 21:56 ` Justin T. Gibbs
2003-06-12 22:24 ` Russell Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20040711131224.GA13575@sh.cvut.cz \
--to=a.kral@sh.cvut.cz \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.