From: Hermann Gottschalk <hg@ostc.de>
To: bert hubert <ahu@ds9a.nl>
Cc: linux-kernel@vger.kernel.org
Subject: Re: Strange Network behaviour
Date: Wed, 14 Jul 2004 10:00:36 +0200 [thread overview]
Message-ID: <20040714080036.GC11178@ostc.de> (raw)
In-Reply-To: <20040704164654.GA18688@outpost.ds9a.nl>
On Sun, Jul 04, 2004 at 06:46:54PM +0200, bert hubert wrote:
> On Fri, Jul 02, 2004 at 05:30:28PM +0200, Hermann Gottschalk wrote:
>
> > This happend for a long time until there was a kernel patch from
> > 2.4.21-215 to 2.4.21-266. Since it is installed this error doesn't
> > appear anymore.
>
> If it ever happens again, supply the output of ifconfig after it happens,
> and dmesg, and lspci -v -v -v. Sure looks like a weird error though,
> probably not related to your network interfaces.
>
> 'Protocol not available' is a weird one.
>
> Perhaps something with modules?
OK, now after an "update" to 2.4.21-231 (SuSE 9.0) some similar
Errors occur:
1) The via-rhine IF isn't accessible anymore. It's up but doesn't work.
2) We work with lvm and lvm-snapshots can't be removed anymore. I
get a segmentation fault.
Here the ouputs:
ifconfig
---------
eth0 Link encap:Ethernet HWaddr 00:0C:76:3F:D6:C4
inet addr:172.16.0.12 Bcast:172.16.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:207507 errors:0 dropped:0 overruns:0 frame:0
TX packets:196605 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:92145974 (87.8 Mb) TX bytes:64863064 (61.8 Mb)
Interrupt:5 Base address:0xbc00 Memory:fe9e0000-fea00000
eth0:0 Link encap:Ethernet HWaddr 00:0C:76:3F:D6:C4
inet addr:172.16.2.12 Bcast:172.16.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Interrupt:5 Base address:0xbc00 Memory:fe9e0000-fea00000
eth1 Link encap:Ethernet HWaddr 00:0D:88:4F:24:9B
inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:12 Base address:0xc800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:130 errors:0 dropped:0 overruns:0 frame:0
TX packets:130 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:11491 (11.2 Kb) TX bytes:11491 (11.2 Kb)
---------
dmesg
---------
: IRQ (10) already programmed
PIC: IRQ (5) already programmed
PIC: IRQ (12) already programmed
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 9
00:03:09[A] -> IRQ 9 Mode 1 Trigger 1
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 9
PIC: IRQ (9) already programmed
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
PIC: IRQ (11) already programmed
PIC: IRQ (12) already programmed
PIC: IRQ (9) already programmed
PIC: IRQ (9) already programmed
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16)
apm: overridden by ACPI.
Starting kswapd
bigpage subsystem: allocated 0 bigpages (=0MB).
allocated 32 pages and 32 bhs reserved for the highmem bounces
kinoded started
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 131068
aio_setup: sizeof(struct page) = 48
vesafb: framebuffer at 0xf0000000, mapped to 0xf8817000, size 65536k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:ec70
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.0.9-2003/09/08: looking for picture.... silenjpeg size 22326 bytes, found (1024x768, 11098 bytes, v3).
bootsplash: silent jpeg found.
bootsplash: silent jpeg found.
Console: switching to colour frame buffer device 118x38
fb0: VESA VGA frame buffer device
Detected PS/2 Mouse Port.
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
Real Time Clock Driver v1.10e
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
loop: loaded (max 16 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX-4: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
PIIX-4: chipset revision 2
PIIX-4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
hdc: JLMS XJ-HD166S, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 16384 buckets, 128Kbytes
TCP: Hash tables configured (established 524288 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
cryptoapi: loaded
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 395k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.36
<Adaptec 29160 Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/253 SCBs
(scsi0:A:0): 160.000MB/s transfers (80.000MHz DT, offset 127, 16bit)
Vendor: MAXTOR Model: ATLAS10K4_73WLS Rev: DFV0
Type: Direct-Access ANSI SCSI revision: 03
scsi0:A:0:0: Tagged Queuing enabled. Depth 32
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 143666192 512-byte hdwr sectors (73557 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
Journalled Block Device driver loaded
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Trying to move old root to /initrd ... failed
Unmounting old root
Trying to free ramdisk memory ... okay
Freeing unused kernel memory: 160k freed
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal
lvm-mp: allocating 42 lowmem entries at c39b9000
LVM version 1.0.5+(mp-v6d)(22/07/2002) module loaded
Adding Swap: 2104472k swap-space (priority 42)
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,3), internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,0), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,3), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on lvm(58,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
bootsplash: silent jpeg found.
Intel(R) PRO/1000 Network Driver - version 5.2.16
Copyright (c) 1999-2003 Intel Corporation.
PCI: Setting latency timer of device 02:01.0 to 64
eth0: Intel(R) PRO/1000 Network Connection
via-rhine.c:v1.10-LK1.1.17 March-1-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
eth1: VIA VT6105 Rhine-III at 0xc800, 00:0d:88:4f:24:9b, IRQ 12.
eth1: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
raw1394: /dev/raw1394 device initialized
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
PCI: Setting latency timer of device 00:1d.7 to 64
ehci_hcd 00:1d.7: Intel Corp. 82801EB USB2 Enhanced Host Controller
ehci_hcd 00:1d.7: irq 12, pci mem fc995c00
usb.c: new USB bus registered, assigned bus number 1
ehci_hcd 00:1d.7: enabled 64bit PCI DMA
PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:1d.7 PCI cache line size corrected to 32.
ehci_hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jun-19/2.4
hub.c: USB hub found
hub.c: 8 ports detected
usb-uhci.c: $Revision: 1.275 $ time 16:12:56 Jun 28 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xe400, IRQ 12
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
usb-uhci.c: USB UHCI at I/O 0xe800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.3 to 64
usb-uhci.c: USB UHCI at I/O 0xec00, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 5
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
uhci.c: USB Universal Host Controller Interface driver v1.1
mice: PS/2 mouse device common for all mice
e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU1] (supports C1, 8 throttling states)
ACPI: Processor [CPU2] (supports C1, 8 throttling states)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
bootsplash: silent jpeg found.
keyboard: Timeout - AT keyboard not present?(f4)
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
keyboard: Timeout - AT keyboard not present?(f4)
keyboard: Timeout - AT keyboard not present?(f4)
keyboard: Timeout - AT keyboard not present?(f4)
keyboard: Timeout - AT keyboard not present?(f4)
keyboard: Timeout - AT keyboard not present?(f4)
keyboard: Timeout - AT keyboard not present?(f4)
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
device eth0 entered promiscuous mode
device eth0 left promiscuous mode
eth1: Promiscuous mode enabled.
device eth1 entered promiscuous mode
device eth1 left promiscuous mode
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
kernel BUG at memory.c:531!
invalid operand: 0000 2.4.21-231-default #1 Mon Jun 28 15:39:34 UTC 2004
CPU: 0
EIP: 0010:[<c012db64>] Not tainted
EFLAGS: 00010246
eax: 00000000 ebx: c10db0b0 ecx: 0000000b edx: c27ffd40
esi: c2802670 edi: 00000000 ebp: 00000006 esp: caa93d7c
ds: 0018 es: 0018 ss: 0018
Process lvremove (pid: 28873, stackpage=caa93000)
Stack: c10db0b0 c39a2220 c012dfd7 c10db0b0 c3946c00 c3946c00 c3946600 c3975447
c39a2220 c39a2220 c39ed000 c39736c4 c3946c00 c3946770 4004fe21 00000000
c39ed000 bffff300 c3970940 00000000 c3979ca0 ffffffff c54c6a00 c5c377e8
Call Trace: [<c012dfd7>] (20) [<c3975447>] (16) [<c39736c4>] (28)
[<c3970940>] (08) [<c3979ca0>] (16) [<c012f795>] (44) [<c0118718>] (28)
[<c022615b>] (12) [<c02262b2>] (08) [<c024daf8>] (40) [<c022615b>] (12)
[<c02262b2>] (04) [<c013437e>] (12) [<c0134488>] (36) [<c012f2d3>] (72)
[<c014ed80>] (24) [<c0151c8a>] (16) [<c014492b>] (48) [<c0144a94>] (24)
[<c01438f4>] (28) [<c01437b0>] (24) [<c0152e26>] (32) [<c0143b0c>] (20)
[<c0108e13>] (60)
Modules: [(lvm-mod:<c3970060>:<c397f644>)]
Code: 0f 0b 13 02 a6 22 2a c0 eb dc 89 f6 55 57 56 53 57 57 83 7c
<6>NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
NETDEV WATCHDOG: eth1: transmit timed out
eth1: Transmit timed out, status 0000, PHY status 786d, resetting...
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
via-rhine.c:v1.10-LK1.1.17 March-1-2003 Written by Donald Becker
http://www.scyld.com/network/via-rhine.html
via-rhine: Reset not complete yet. Trying harder.
eth1: VIA VT6105 Rhine-III at 0xc800, 00:0d:88:4f:24:9b, IRQ 12.
eth1: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
eth1: Reset not complete yet. Trying harder.
eth1: Setting full-duplex based on MII #1 link partner capability of 45e1.
---------
lspci -v -v -v
---------
00:00.0 Host bridge: Intel Corp. 82865G/PE/P Processor to I/O Controller (rev 02)
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7280
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [e4] #09 [2106]
Capabilities: [a0] AGP version 3.0
Status: RQ=32 Iso- ArqSz=2 Cal=2 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=2 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
00:01.0 PCI bridge: Intel Corp. 82865G/PE/P Processor to AGP Controller (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fc800000-fe8fffff
Prefetchable memory behind bridge: efe00000-f7dfffff
BridgeCtl: Parity+ SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:03.0 PCI bridge: Intel Corp. 82865G/PE/P Processor to PCI to CSA Bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: fe900000-fe9fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1d.0 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7280
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at e000 [size=32]
00:1d.1 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7280
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 12
Region 4: I/O ports at e400 [size=32]
00:1d.2 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7280
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 5
Region 4: I/O ports at e800 [size=32]
00:1d.3 USB Controller: Intel Corp. 82801EB USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7280
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 4: I/O ports at ec00 [size=32]
00:1d.7 USB Controller: Intel Corp. 82801EB USB2 (rev 02) (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7280
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 12
Region 0: Memory at febffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [58] #0a [20a0]
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev c2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: f7e00000-f7efffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801EB LPC Interface Controller (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801EB Ultra ATA Storage Controller (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7280
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at fc00 [size=16]
Region 5: Memory at 80000000 (32-bit, non-prefetchable) [size=1K]
00:1f.3 SMBus: Intel Corp. 82801EB SMBus Controller (rev 02)
Subsystem: Micro-Star International Co., Ltd.: Unknown device 7280
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at 0c00 [size=32]
01:00.0 VGA compatible controller: nVidia Corporation NV18 [GeForce4 MX 440 AGP 8x] (rev a4) (prog-if 00 [VGA])
Subsystem: LeadTek Research Inc.: Unknown device 2924
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Expansion ROM at fe8e0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
02:01.0 Ethernet controller: Intel Corp.: Unknown device 1019
Subsystem: Micro-Star International Co., Ltd.: Unknown device 728c
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (63750ns min), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fe9e0000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at bc00 [size=32]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
03:01.0 SCSI storage controller: Adaptec AIC-7892A U160/m (rev 02)
Subsystem: Adaptec 29160 Ultra160 SCSI Controller
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (10000ns min, 6250ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
BIST result: 00
Region 0: I/O ports at cc00 [disabled] [size=256]
Region 1: Memory at feaff000 (64-bit, non-prefetchable) [size=4K]
Expansion ROM at feac0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
03:03.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III] (rev 86)
Subsystem: D-Link System Inc: Unknown device 1403
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), cache line size 08
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at c800 [size=256]
Region 1: Memory at feafef00 (32-bit, non-prefetchable) [size=256]
Expansion ROM at feab0000 [disabled] [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
---------
Any ideas?
Greetings Hermann
--
___ ___ _____ ___ ___ _ _ _
/ _ \/ __|_ _/ __| / __|_ __ | |__| || |
| (_) \__ \ | || (__ | (_ | ' \| '_ \ __ |
\___/|___/ |_| \___| \___|_|_|_|_.__/_||_|
----------------------------------------------
OSTC Open Source Training and Consulting GmbH
90425 Nürnberg Web: http://www.ostc.de
----------------------------------------------
PGP-Key: 0x0B2D8EEA
No HTML-Mails; 72 Characters per line
next prev parent reply other threads:[~2004-07-14 8:02 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-07-02 15:30 Strange Network behaviour Hermann Gottschalk
2004-07-04 16:46 ` bert hubert
2004-07-14 8:00 ` Hermann Gottschalk [this message]
2004-07-14 9:02 ` Roger Luethi
2004-07-14 10:28 ` Hermann Gottschalk
2004-07-14 10:33 ` Roger Luethi
2004-07-14 10:40 ` Hermann Gottschalk
2004-07-14 10:48 ` Roger Luethi
[not found] ` <20040714105546.GA12380@ostc.de>
[not found] ` <20040714110348.GA6393@k3.hellgate.ch>
2004-07-14 12:51 ` Hermann Gottschalk
2004-07-14 16:13 ` Gene Heskett
-- strict thread matches above, loose matches on Subject: below --
2007-12-04 22:44 Strange network behaviour Mike
[not found] ` <4755D859.4090805-kcIQ9yavhvsV/sYkb9DZNQ@public.gmane.org>
2007-12-05 7:53 ` Lynn Kerby
[not found] ` <52FC3F66-4055-4C6C-9920-8FE4C6BD2CCA-br2HoPxSX4msTnJN9+BGXg@public.gmane.org>
2007-12-05 9:06 ` Mike
[not found] ` <47566A0B.8040105-kcIQ9yavhvsV/sYkb9DZNQ@public.gmane.org>
2007-12-05 9:17 ` Dor Laor
[not found] ` <47566CB2.9060706-atKUWr5tajBWk0Htik3J/w@public.gmane.org>
2007-12-05 9:42 ` Mike
2007-12-05 9:46 ` Izik Eidus
2007-12-05 10:29 ` Avi Kivity
[not found] ` <47567D6D.8060802-atKUWr5tajBWk0Htik3J/w@public.gmane.org>
2007-12-05 10:39 ` Mike
[not found] ` <47567FC7.9040106-kcIQ9yavhvsV/sYkb9DZNQ@public.gmane.org>
2007-12-05 10:43 ` Avi Kivity
[not found] ` <475680E8.4060508-atKUWr5tajBWk0Htik3J/w@public.gmane.org>
2007-12-05 11:22 ` Mike
[not found] ` <475689E0.5020901-kcIQ9yavhvsV/sYkb9DZNQ@public.gmane.org>
2007-12-05 11:46 ` Uri Lublin
2007-12-05 13:18 ` Avi Kivity
[not found] ` <4756A538.1050303-atKUWr5tajBWk0Htik3J/w@public.gmane.org>
2007-12-05 14:13 ` Mike
[not found] ` <4756B1F6.5080102-kcIQ9yavhvsV/sYkb9DZNQ@public.gmane.org>
2007-12-05 15:56 ` Avi Kivity
[not found] ` <4756CA29.5030501-atKUWr5tajBWk0Htik3J/w@public.gmane.org>
2007-12-05 17:21 ` Mike
[not found] ` <4756DE36.2020502-kcIQ9yavhvsV/sYkb9DZNQ@public.gmane.org>
2007-12-05 18:05 ` Simon Gao
[not found] ` <4756E86B.8050402-g4dUTk+gKbW4mfPA/iJWtA@public.gmane.org>
2007-12-05 19:49 ` Lynn Kerby
2007-12-05 10:55 ` Pelle
[not found] ` <475683A6.5050900-5JapdU7xTciEVqv0pETR8A@public.gmane.org>
2007-12-05 12:39 ` Avi Kivity
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20040714080036.GC11178@ostc.de \
--to=hg@ostc.de \
--cc=ahu@ds9a.nl \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.