All of lore.kernel.org
 help / color / mirror / Atom feed
From: Ben Collins <bcollins@debian.org>
To: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux1394-devel@lists.sourceforge.net,
	Linux Kernel list <linux-kernel@vger.kernel.org>
Subject: Re: OHCI driver dies on Mac Mini at boot
Date: Mon, 14 Mar 2005 18:50:50 -0500	[thread overview]
Message-ID: <20050314235050.GD1437@internal> (raw)
In-Reply-To: <1110846336.5673.53.camel@gaston>

Send me the lspci -v output for this machine.

On Tue, Mar 15, 2005 at 11:25:36AM +1100, Benjamin Herrenschmidt wrote:
> I get this output with current Linus bk : 
> 
> [    0.000000] Total memory = 512MB; using 1024kB for hash table (at 80400000)
> [    0.000000] Linux version 2.6.11-gack (benh@gaston) (gcc version 3.3.5 (Debian 1:3.3.5-8)) #5 Tue Mar 15 11:20:41 EST 2005
> [    0.000000] Found UniNorth memory controller & host bridge, revision: 210
> [    0.000000] Mapped at 0xfdd68000
> [    0.000000] Found a Intrepid mac-io controller, rev: 0, mapped at 0xfdce8000
> [    0.000000] Processor NAP mode on idle enabled.
> [    0.000000] PowerMac motherboard: Mac mini
> [    0.000000] Found UniNorth PCI host bridge at 0xf0000000. Firmware bus number: 0->0
> [    0.000000] Found UniNorth PCI host bridge at 0xf2000000. Firmware bus number: 0->0
> [    0.000000] Found UniNorth PCI host bridge at 0xf4000000. Firmware bus number: 0->0
> [    0.000000] via-pmu: Server Mode is disabled
> [    0.000000] PMU driver 2 initialized for Core99, firmware: 55
> [    0.000000] nvram: Checking bank 0...
> [    0.000000] nvram: gen0=122, gen1=121
> [    0.000000] nvram: Active bank is: 0
> [    0.000000] nvram: OF partition at 0x410
> [    0.000000] nvram: XP partition at 0x1020
> [    0.000000] nvram: NR partition at 0x1120
> [    0.000000] On node 0 totalpages: 131072
> [    0.000000]   DMA zone: 131072 pages, LIFO batch:16
> [    0.000000]   Normal zone: 0 pages, LIFO batch:1
> [    0.000000]   HighMem zone: 0 pages, LIFO batch:1
> [    0.000000] Built 1 zonelists
> [    0.000000] Kernel command line: s
> [    0.000000] PowerMac using OpenPIC irq controller at 0x80040000
> [    0.000000] OpenPIC Version 1.2 (4 CPUs and 64 IRQ sources) at fc496000
> [    0.000000] OpenPIC timer frequency is 4.166666 MHz
> [    0.000000] PID hash table entries: 4096 (order: 12, 65536 bytes)
> [    0.000000] GMT Delta read from XPRAM: 0 minutes, DST: off
> [    0.000000] time_init: decrementer frequency = 41.620997 MHz
> [   69.359998] Console: colour dummy device 80x25
> [   69.360691] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
> [   69.361601] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
> [   69.380943] Memory: 512896k available (2580k kernel code, 1336k data, 176k init, 0k highmem)
> [   69.380964] System.map loaded at 0x811bd000 for debugger, size: 963019 bytes
> [   69.380972] AGP special page: 0x9ffff000
> [   69.381051] Calibrating delay loop... 1413.12 BogoMIPS (lpj=706560)
> [   69.402356] Mount-cache hash table entries: 512
> [   69.404165] NET: Registered protocol family 16
> [   69.405106] PCI: Probing PCI hardware
> [   69.406287] PCI: Cannot allocate resource region 0 of device 0001:10:18.0
> [   69.406299] PCI: Cannot allocate resource region 0 of device 0001:10:19.0
> [   69.406322] Apple USB OHCI 0001:10:18.0 disabled by firmware
> [   69.406331] Apple USB OHCI 0001:10:19.0 disabled by firmware
> [   69.406390] Registering openpic with sysfs...
> [   69.407120] SCSI subsystem initialized
> [   69.407258] usbcore: registered new driver usbfs
> [   69.407289] usbcore: registered new driver hub
> [   69.408749] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> [   69.409293] PCI: Enabling device 0000:00:10.0 (0006 -> 0007)
> [   69.925273] radeonfb (0000:00:10.0): Invalid ROM signature 0 should be0xaa55
> [   69.925294] radeonfb: Retreived PLL infos from Open Firmware
> [   69.925303] radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=190.00 Mhz, System=250.00 MHz
> [   69.925314] radeonfb: PLL min 12000 max 35000
> [   70.517246] radeonfb: Monitor 1 type DFP found
> [   70.517263] radeonfb: EDID probed
> [   70.517269] radeonfb: Monitor 2 type DFP found
> [   70.517275] radeonfb: EDID probed
> [   70.611713] Console: switching to colour frame buffer device 240x75
> [   70.611913] radeonfb (0000:00:10.0): ATI Radeon Yb 
> [   70.626083] Generic RTC Driver v1.07
> [   70.626274] Macintosh non-volatile memory driver v1.1
> [   70.626540] io scheduler noop registered
> [   70.626702] io scheduler anticipatory registered
> [   70.626861] io scheduler deadline registered
> [   70.627015] io scheduler cfq registered
> [   70.627552] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> [   70.627979] loop: loaded (max 8 devices)
> [   70.628137] sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com)
> [   70.690585] PHY ID: 4061e4, addr: 0
> [   70.691210] eth0: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:11:24:76:c8:ea 
> [   70.691524] eth0: Found BCM5221 PHY
> [   70.691694] pcnet32.c:v1.30i 06.28.2004 tsbogend@alpha.franken.de
> [   70.691954] PPP generic driver version 2.4.2
> [   70.692139] PPP Deflate Compression module registered
> [   70.692337] MacIO PCI driver attached to Intrepid chipset
> [   70.692956] input: Macintosh mouse button emulation
> [   70.693211] apm_emu: APM Emulation 0.5 initialized.
> [   70.693421] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> [   70.693620] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> [   70.693882] adb: starting probe task...
> [   70.694008] adb: finished probe task...
> [   70.694322] PCI: Enabling device 0002:20:0d.0 (0004 -> 0006)
> [   71.706181] ide0: Found Apple UniNorth ATA-6 controller, bus ID 3, irq 39
> [   71.706404] Probing IDE interface ide0...
> [   71.970334] hda: TOSHIBA MK8025GAS, ATA DISK drive
> [   72.378303] hdb: MATSHITACD-RW CW-8123, ATAPI CD/DVD-ROM drive
> [   72.429131] hda: Enabling Ultra DMA 5
> [   72.430274] hdb: Enabling Ultra DMA 2
> [   72.431454] ide0 at 0xa101a000-0xa101a007,0xa101a160 on irq 39
> [   73.090239] eth0: Link is up at 100 Mbps, full-duplex.
> [   73.443069] ide1: Found Apple KeyLargo ATA-3 controller, bus ID 0, irq 24
> [   73.443287] Probing IDE interface ide1...
> [   73.962026] ide1: Bus empty, interface released.
> [   73.962215] hda: max request size: 1024KiB
> [   74.216212] hda: 156301488 sectors (80026 MB), CHS=16383/255/63, UDMA(100)
> [   74.216523] hda: cache flushes supported
> [   74.216723]  hda: [mac] hda1 hda2 hda3 hda4 hda5 hda6 hda7 hda8
> [   74.282414] hdb: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
> [   74.282712] Uniform CD-ROM driver Revision: 3.20
> [   74.284641] ide-floppy driver 0.99.newide
> [   74.284893] mesh: configured for synchronous 5 MB/s
> [   74.285105] st: Version 20041025, fixed bufsize 32768, s/g segs 256
> [   74.285418] usbmon: debugs is not available
> [   74.285553] ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
> [   74.285592] Apple USB OHCI 0001:10:18.0 disabled by firmware
> [   74.285773] Apple USB OHCI 0001:10:19.0 disabled by firmware
> [   74.285954] PCI: Enabling device 0001:10:1a.0 (0000 -> 0002)
> [   74.295306] ohci_hcd 0001:10:1a.0: Apple Computer Inc. KeyLargo/Intrepid USB (#3)
> [   74.304588] ohci_hcd 0001:10:1a.0: new USB bus registered, assigned bus number 1
> [   74.313747] ohci_hcd 0001:10:1a.0: irq 29, io mem 0x80083000
> [   74.353116] hub 1-0:1.0: USB hub found
> [   74.362232] hub 1-0:1.0: 2 ports detected
> [   74.392029] PCI: Enabling device 0001:10:1b.0 (0000 -> 0002)
> [   74.401126] ohci_hcd 0001:10:1b.0: NEC Corporation USB
> [   74.410400] ohci_hcd 0001:10:1b.0: new USB bus registered, assigned bus number 2
> [   74.419646] ohci_hcd 0001:10:1b.0: irq 63, io mem 0x80082000
> [   74.459072] hub 2-0:1.0: USB hub found
> [   74.468330] hub 2-0:1.0: 3 ports detected
> [   74.498025] PCI: Enabling device 0001:10:1b.1 (0000 -> 0002)
> [   74.507405] ohci_hcd 0001:10:1b.1: NEC Corporation USB (#2)
> [   74.516803] ohci_hcd 0001:10:1b.1: new USB bus registered, assigned bus number 3
> [   74.526190] ohci_hcd 0001:10:1b.1: irq 63, io mem 0x80081000
> [   74.566061] hub 3-0:1.0: USB hub found
> [   74.575288] hub 3-0:1.0: 2 ports detected
> [   74.662013] usbcore: registered new driver usbhid
> [   74.671081] drivers/usb/input/hid-core.c: v2.01:USB HID core driver
> [   74.680311] mice: PS/2 mouse device common for all mice
> [   74.689528] oprofile: using timer interrupt.
> [   74.698770] NET: Registered protocol family 2
> [   74.718042] IP: routing cache hash table of 4096 buckets, 32Kbytes
> [   74.727650] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
> [   74.739914] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
> [   74.749784] TCP: Hash tables configured (established 131072 bind 65536)
> [   74.759471] NET: Registered protocol family 1
> [   74.768982] NET: Registered protocol family 17
> [   74.788984] usb 2-1: new low speed USB device using ohci_hcd and address 2
> [   74.798912] EXT3-fs: INFO: recovery required on readonly filesystem.
> [   74.808580] EXT3-fs: write access will be enabled during recovery.
> [   74.935605] input: USB HID v1.10 Mouse [Microsoft Basic Optical Mouse] on usb-0001:10:1b.0-1
> [   74.977829] kjournald starting.  Commit interval 5 seconds
> [   74.987617] EXT3-fs: recovery complete.
> [   74.998266] EXT3-fs: mounted filesystem with ordered data mode.
> [   75.007984] VFS: Mounted root (ext3 filesystem) readonly.
> [   75.017680] Freeing unused kernel memory: 176k init 4k chrp 8k prep
> [   75.229947] usb 3-1: new low speed USB device using ohci_hcd and address 2
> [   75.401614] input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0001:10:1b.1-1
> [   75.424797] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0001:10:1b.1-1
> [   80.639297] Adding 1953116k swap on /dev/hda6.  Priority:-1 extents:1
> [   80.787420] EXT3 FS on hda4, internal journal
> [   84.020857] ieee1394: Initialized config rom entry `ip1394'
> [   84.048240] sbp2: $Rev: 1219 $ Ben Collins <bcollins@debian.org>
> [   84.203758] Found KeyWest i2c on "uni-n", 2 channels, stepping: 4 bits
> [   84.215110] Found KeyWest i2c on "mac-io", 1 channel, stepping: 4 bits
> [   85.392553] kjournald starting.  Commit interval 5 seconds
> [   85.402199] EXT3 FS on hda5, internal journal
> [   85.411612] EXT3-fs: mounted filesystem with ordered data mode.
> [   85.444911] kjournald starting.  Commit interval 5 seconds
> [   85.454548] EXT3 FS on hda7, internal journal
> [   85.464029] EXT3-fs: mounted filesystem with ordered data mode.
> [   88.155217] ohci1394: $Rev: 1250 $ Ben Collins <bcollins@debian.org>
> [   88.164904] PCI: Enabling device 0002:20:0e.0 (0000 -> 0002)
> [   88.188723] ohci1394: fw-host0: Unexpected PCI resource length of 1000!
> [   88.250601] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[40]  MMIO=[f5000000-f50007ff]  Max Packet=[2048]
> [   89.741666] Linux agpgart interface v0.101 (c) Dave Jones
> [   89.803084] agpgart: Detected Apple UniNorth 2 chipset
> [   89.812583] agpgart: configuring for size idx: 4
> [   89.824113] agpgart: AGP aperture is 16M @ 0x0
> [   89.941059] ohci1394: fw-host0: Unrecoverable error!
> [   89.950220] ohci1394: fw-host0: Async Req Rcv Context died: ctrl[00008808] cmdptr[1ef28000]
> [   89.959378] ohci1394: fw-host0: Error in reception of SelfID packets [0x8002000c/0x00000000] (count: 0)
> [   89.970595] ohci1394: fw-host0: SelfID received outside of bus reset sequence
> [   90.235036] ieee1394: impossible ack_complete from node 65535 (tcode 4)
> [   90.244330] ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting...
> [   90.246363] ohci1394: fw-host0: Error in reception of SelfID packets [0x8004000c/0x00000000] (count: 1)
> [   90.257846] ohci1394: fw-host0: SelfID received outside of bus reset sequence
> [   90.513026] ieee1394: impossible ack_complete from node 65535 (tcode 4)
> [   90.522642] ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting...
> [   90.524673] ohci1394: fw-host0: Error in reception of SelfID packets [0x8006000c/0x00000000] (count: 2)
> [   90.536379] ohci1394: fw-host0: SelfID received outside of bus reset sequence
> [   90.801002] ieee1394: impossible ack_complete from node 65535 (tcode 4)
> [   90.810758] ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting...
> [   90.812788] ohci1394: fw-host0: Error in reception of SelfID packets [0x8008000c/0x00000000] (count: 3)
> [   90.824645] ohci1394: fw-host0: SelfID received outside of bus reset sequence
> [   91.079999] ieee1394: impossible ack_complete from node 65535 (tcode 4)
> [   91.089869] ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting...
> [   91.091900] ohci1394: fw-host0: Error in reception of SelfID packets [0x800a000c/0x00000000] (count: 4)
> [   91.104034] ohci1394: fw-host0: SelfID received outside of bus reset sequence
> [   91.375966] ieee1394: impossible ack_complete from node 65535 (tcode 4)
> [   91.386009] ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting...
> [   91.388038] ohci1394: fw-host0: Error in reception of SelfID packets [0x800c000c/0x00000000] (count: 5)
> [   91.400264] ohci1394: fw-host0: SelfID received outside of bus reset sequence
> [   91.655954] ieee1394: impossible ack_complete from node 65535 (tcode 4)
> [   91.666503] ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting...
> [   91.666507] ieee1394: Stopping reset loop for IRM sanity
> [   96.598155] eth0: Link is up at 100 Mbps, full-duplex.
> [   96.608017] eth0: Pause is disabled
> 
> 
> 
> 
> -------------------------------------------------------
> SF email is sponsored by - The IT Product Guide
> Read honest & candid reviews on hundreds of IT Products from real users.
> Discover which products truly live up to the hype. Start reading now.
> http://ads.osdn.com/?ad_id=6595&alloc_id=14396&op=click
> _______________________________________________
> mailing list linux1394-devel@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/linux1394-devel

-- 
Debian     - http://www.debian.org/
Linux 1394 - http://www.linux1394.org/
Subversion - http://subversion.tigris.org/
WatchGuard - http://www.watchguard.com/

      reply	other threads:[~2005-03-15  2:18 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2005-03-15  0:25 OHCI driver dies on Mac Mini at boot Benjamin Herrenschmidt
2005-03-14 23:50 ` Ben Collins [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20050314235050.GD1437@internal \
    --to=bcollins@debian.org \
    --cc=benh@kernel.crashing.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux1394-devel@lists.sourceforge.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.