All of lore.kernel.org
 help / color / mirror / Atom feed
From: zhonglei <zhonglei@RCS-9000.COM>
To: u-boot@lists.denx.de
Subject: [U-Boot-Users] how can I run linux without tftp
Date: Wed, 11 May 2005 14:08:23 +0800	[thread overview]
Message-ID: <200505111408.AA28377416@RCS-9000.COM> (raw)

hi
   I have no ethernet device on my board,so I can only load linux img file via serial port using "loadb" command. But when I downloaded the img successfully and tried to boot the linux , the program stopped as follows:
**********************************************************************
=> loadb 00100000                 
## Ready for binary (kermit) download to 0x00100000 at 115200 bps...                                                                    
## Total Size      = 0x000cb02a = 831530 Bytes                                              
## Start Addr      = 0x00100000                               
=> bootm        
## Booting image at 00100000 ...                                
   Image Name:   Linux-2.4.25                             
   Image Type:   PowerPC Linux Kernel Image (gz                                              
   Data Size:    831466 Bytes = 812 kB                                      
   Load Address: 00000000                         
   Entry Point:  00000000                         
   Verifying Checksum ... OK                            
   Uncompressing Kernel Image ... OK                                    
Memory BAT mapping: BAT2=32Mb, BAT3=0Mb, residual: 0Mb                                                      
Linux version 2.4.25 (root at 198.87.102.69.netdial.caribe.net) (gcc version 3.2.2                                                                               
20030217 (Yellow Dog Linux 3.0 3.2.2-2a_1)) #2 Tue May 10 14:19:41 CST 2005                                                                           
On node 0 totalpages: 8192                          
zone(0): 8192 pages.                    
zone(1): 0 pages.                 
zone(2): 0 pages.                 
Kernel command line:                    
Calibrating delay loop... 263.78 BogoMIPS                                         
Memory: 29876k available (1456k kernel code, 460k data, 76k init, 0k highmem)                                                                             
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)                                                             
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)                                                            
Mount cache hash table entries: 512 (order: 0, 4096 bytes)                                                          
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)                                                            
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)                                                           
POSIX conformance testing by UNIFIX                                   
PCI: Probing PCI hardware                         
PCI: Cannot allocate resource region 0 of device 00:1a.0                                                        
Linux NET4.0 for                
Based upon Swansea University Computer Society NET3.039                                                       
Initializing RT netlink socket                              
Starting kswapd               
Journalled Block Device driver loaded                                     
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.                                              
pty: 256 Unix98 ptys configured                               
ttyS0 on PSC1             
ttyS1 on PSC2             
ttyS2 on PSC3             
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize                                                                      
loop: loaded (max 8 devices)                            
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4                                                           
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx                                                                           
Port Config is: 0x910                   
ipb=66MHz, set clock period to 15                                 
GPIO config: 91050004                     
ATA invalid: 00800000                     
ATA hostcnf: 03000000                     
ATA pio1   : 100a0a00                     
ATA pio2   : 02040600                     
XLB Arb cnf: 0000a366                     
mpc5xxx_ide: Setting up IDE interface ide0...                                             
ATA DMA task: 5               
Probing IDE interface ide0...                             
ide0: Wait for ready failed before probe !                                          
Probe at base[0x55](0x00000055) past the end of the map(0x00000000)                                                                   
Probe at base[0x55](0x00000055) past the end of the map(0x00000000)                                                                   
CFI: Found no Icecube Bank 0 device at location zero                                                    
Icecube: No supported flash c                            
NET4: Linux TCP/IP 1.0 for NET4.0                                 
eth0: Phy @ 0x0, type GENERIC (0x007f007f)                                          
IP Protocols: ICMP, UDP, TCP, IGMP                                  
IP: routing cache hash table of 512 buckets, 4Kbytes                                                    
TCP: Hash tables configured (established 2048 bind 4096)                                                        
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.                                                   
Root-NFS: No NFS server available, giving up.                                             
VFS: Unable to mount root fs via NFS, trying floppy.                                                    
VFS: Cannot open root device "" or 02:00                                        
Please append a correct "root=" boot option                                           
Kernel panic: VFS: Unable to mount root fs on 02:00                                                   
 <0>Rebooting in 180 seconds..                              
*********************************************************************

Please give me a help! Thanks a lot!
Best Regards
zhonglei

             reply	other threads:[~2005-05-11  6:08 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2005-05-11  6:08 zhonglei [this message]
2005-05-11  7:54 ` [U-Boot-Users] how can I run linux without tftp Wolfgang Denk
     [not found] <200505111615.AA27132010@RCS-9000.COM>
2005-05-11  8:57 ` Wolfgang Denk

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=200505111408.AA28377416@RCS-9000.COM \
    --to=zhonglei@rcs-9000.com \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.