From: Thiemo Seufer <ths@networkno.de>
To: linux-mips@linux-mips.org
Subject: Current SGI Octane status
Date: Sat, 9 Jul 2005 11:34:04 +0200 [thread overview]
Message-ID: <20050709093403.GB1586@hattusa.textio> (raw)
Hello All,
I tried current CVS HEAD plus the patches from
ftp://ftp.linux-mips.org/pub/linux/mips/people/skylark/
on an SMP Octane with 2x195 MHz R10000 and ESI graphics.
Results:
- Local console works.
- IOC3 networking works, with 2MB/s maximum for a 30MB http transfer
- Serial console works, but start of output is delayed. The driver
probably lacks transfer bootstrap, and starts transmisssion only when
the first buffer is full.
- Rebooting for SMP works, but this patch apparently broke arcload (hangs
after "Entering Kernel").
- Serial console and framebuffer initializations seem to be mutually
exclusive, that's impractical if you plan to route console (debug)
output over serial while working on the graphics console.
- 'echo "foo" >/dev/fb0' kills the machine.
The dmesg for a serial boot is appended.
Thiemo
[4294667.296000] Linux version 2.6.12-ip30 (ths@hattusa) (gcc version 4.0.1 20050701 (prerelease) (Debian 4.0.0-12)) #21 SMP Sat Jul 9 10:41:57 CEST 2005
[4294667.296000] ARCH: SGI-IP30
[4294667.296000] PROMLIB: ARC firmware Version 64 Revision 0
[4294667.296000] CPU revision is: 00000927
[4294667.296000] FPU revision is: 00000900
[4294667.296000] Silicon Graphics Octane (IP30) support: (c) 2004, 2005 Stanislaw Skowronek.
[4294667.296000] xtalk: Detected XBow (revision 1.2) at 0.
[4294667.296000] xtalk: Detected Heart (revision E) at 8.
[4294667.296000] xtalk: Detected HQ4 / ImpactSR (revision B) at 12.
[4294667.296000] xtalk: Detected Bridge (revision C) at 15.
[4294667.296000] BRIDGE chip at xtalk:15, initializing...
[4294667.296000] Determined physical RAM map:
[4294667.296000] memory: 0000000000004000 @ 0000000000000000 (reserved)
[4294667.296000] memory: 00000000004c6000 @ 0000000020004000 (reserved)
[4294667.296000] memory: 0000000000a36000 @ 00000000204ca000 (usable)
[4294667.296000] memory: 0000000000100000 @ 0000000020f00000 (ROM data)
[4294667.296000] memory: 000000003f000000 @ 0000000021000000 (usable)
[4294667.296000] On node 0 totalpages: 393216
[4294667.296000] DMA zone: 393216 pages, LIFO batch:31
[4294667.296000] Normal zone: 0 pages, LIFO batch:1
[4294667.296000] HighMem zone: 0 pages, LIFO batch:1
[4294667.296000] Built 1 zonelists
[4294667.296000] Kernel command line: root=xio(0)pci(15)scsi(0)disk(1)rdisk(0)partition(0) root=/dev/sda1 console=ttyS0
[4294667.296000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
[4294667.296000] Primary data cache 32kB, 2-way, linesize 32 bytes.
[4294667.296000] Unified secondary cache 1024kB 2-way, linesize 128 bytes.
[4294667.296000] Synthesized TLB refill handler (41 instructions).
[4294667.296000] Synthesized TLB load handler fastpath (55 instructions).
[4294667.296000] Synthesized TLB store handler fastpath (55 instructions).
[4294667.296000] Synthesized TLB modify handler fastpath (54 instructions).
[4294667.296000] IP30: interrupt controller initialized.
[4294667.296000] PID hash table entries: 4096 (order: 12, 131072 bytes)
[4294667.296000] IP30: initializing timer.
[4294667.296000] 194 MHz CPU detected
[4294667.296000] Using 97.492 MHz high precision timer.
[4294667.296000] Console: colour dummy device 80x25
[4294667.306000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[4294667.325000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[4294667.560000] Memory: 1017476k/1042648k available (3180k kernel code, 24828k reserved, 1222k data, 248k init, 0k highmem)
[4294667.561000] Calibrating delay loop... 193.53 BogoMIPS (lpj=96768)
[4294667.578000] Mount-cache hash table entries: 256
[4294667.579000] Checking for 'wait' instruction... unavailable.
[4294667.579000] Checking for the multiply/shift bug... no.
[4294667.579000] Checking for the daddi bug... no.
[4294667.579000] Checking for the daddiu bug... no.
[4294667.580000] CPU revision is: 00000927
[4294667.580000] FPU revision is: 00000900
[4294667.580000] Primary instruction cache 32kB, physically tagged, 2-way, linesize 64 bytes.
[4294667.580000] Primary data cache 32kB, 2-way, linesize 32 bytes.
[4294667.580000] Unified secondary cache 1024kB 2-way, linesize 128 bytes.
[4294667.582000] Synthesized TLB refill handler (41 instructions).
[4294667.582000] Calibrating delay loop... 194.56 BogoMIPS (lpj=97280)
[4294667.599000] Brought up 2 CPUs
[4294667.599000] CPU0 attaching sched-domain:
[4294667.599000] domain 0: span 3
[4294667.599000] groups: 1 2
[4294667.599000] CPU1 attaching sched-domain:
[4294667.599000] domain 0: span 3
[4294667.599000] groups: 2 1
[4294667.603000] NET: Registered protocol family 16
[4294667.609000] SCSI subsystem initialized
[4294667.610000] IP30: HEART ATTACK! Caught errors: 0x1040!
[4294667.610000] interrupt #63
[4294667.610000] interrupt #57
[4294667.622000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[4294667.623000] Initializing Cryptographic API
[4294667.623000] PCI: Fixing ioc3 in [bus:slot.fn] 0000:00:02.0
[4294667.623000] PCI: Fixing rad1 in [bus:slot.fn] 0000:00:03.0
[4294667.711000] Console: switching to colour frame buffer device 160x64
[4294667.711000] fb0: ImpactSR 1RSS frame buffer device
[4294667.848000] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
[4294667.850000] io scheduler noop registered
[4294667.850000] io scheduler anticipatory registered
[4294667.850000] io scheduler deadline registered
[4294667.850000] io scheduler cfq registered
[4294667.854000] RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
[4294667.856000] loop: loaded (max 8 devices)
[4294667.856000] tun: Universal TUN/TAP device driver, 1.6
[4294667.856000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[4294667.857000] qla1280: QLA1040 found on PCI bus 0, dev 0
[4294667.857000] PCI: Enabling device 0000:00:00.0 (0006 -> 0007)
[4294668.577000] scsi(0:0): Resetting SCSI BUS
[4294668.579000] scsi0 : QLogic QLA1040 PCI to SCSI Host Adapter
[4294668.579000] Firmware version: 7.65.00, Driver version 3.25
[4294670.747000] Vendor: SEAGATE Model: ST318275LC Rev: 0001
[4294670.747000] Type: Direct-Access ANSI SCSI revision: 02
[4294670.748000] scsi(0:0:1:0): Sync: period 10, offset 12, Wide
[4294672.921000] qla1280: QLA1040 found on PCI bus 0, dev 1
[4294672.921000] PCI: Enabling device 0000:00:01.0 (0006 -> 0007)
[4294673.653000] scsi(1:0): Resetting SCSI BUS
[4294673.656000] scsi1 : QLogic QLA1040 PCI to SCSI Host Adapter
[4294673.656000] Firmware version: 7.65.00, Driver version 3.25
[4294678.158000] SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB)
[4294678.160000] SCSI device sda: drive cache: write back
[4294678.162000] SCSI device sda: 35566480 512-byte hdwr sectors (18210 MB)
[4294678.164000] SCSI device sda: drive cache: write back
[4294678.164000] sda: sda1 sda2 sda9 sda11
[4294678.182000] Attached scsi disk sda at scsi0, channel 0, id 1, lun 0
[4294678.183000] mice: PS/2 mouse device common for all mice
[4294678.183000] md: raid0 personality registered as nr 2
[4294678.183000] md: raid1 personality registered as nr 3
[4294678.183000] md: raid5 personality registered as nr 4
[4294678.183000] raid5: measuring checksumming speed
[4294678.188000] 8regs : 500.000 MB/sec
[4294678.193000] 8regs_prefetch: 476.000 MB/sec
[4294678.198000] 32regs : 496.000 MB/sec
[4294678.203000] 32regs_prefetch: 476.000 MB/sec
[4294678.203000] raid5: using function: 8regs (500.000 MB/sec)
[4294678.203000] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294678.203000] Advanced Linux Sound Architecture Driver Version 1.0.9rc2 (Thu Mar 24 10:33:39 2005 UTC).
[4294678.208000] ALSA device list:
[4294678.208000] #0: SGI RAD Pro Audio at 0x1fa00000
[4294679.420000] IOC3 part: [030-0891-003], serial: [DJK972] => class IP30 system
[4294679.421000] ttyS0 at IOC3 0x1f620178 (irq = 64) is a 16550A
[4294679.423000] ttyS1 at IOC3 0x1f620170 (irq = 64) is a 16550A
[4294679.428000] Ethernet address is 08:00:69:0a:fc:0f.
[4294679.441000] eth0: link up, 100Mbps, half-duplex, lpa 0x00A1
[4294679.442000] eth0: Using PHY 1, vendor 0x15f42, model 2, rev 3.
[4294679.443000] eth0: IOC3 SSRAM has 128 kbyte.
[4294679.444000] IOC3 Master Driver loaded for 0000:00:02.0
[4294679.445000] NET: Registered protocol family 2
[4294679.548000] atkbd.c: keyboard reset failed on ioc3/serio0kbd
[4294680.035000] atkbd.c: keyboard reset failed on ioc3/serio0aux
[4294680.429000] IP: routing cache hash table of 8192 buckets, 128Kbytes
[4294680.431000] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[4294680.463000] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[4294680.471000] TCP: Hash tables configured (established 262144 bind 65536)
[4294680.472000] NET: Registered protocol family 1
[4294680.473000] NET: Registered protocol family 17
[4294680.474000] NET: Registered protocol family 15
[4294680.476000] md: Autodetecting RAID arrays.
[4294680.477000] md: autorun ...
[4294680.478000] md: ... autorun DONE.
[4294680.506000] kjournald starting. Commit interval 5 seconds
[4294680.581000] EXT3-fs: mounted filesystem with ordered data mode.
[4294680.662000] VFS: Mounted root (ext3 filesystem) readonly.
[4294680.736000] Freeing prom memory: 1024kb freed
[4294680.796000] Freeing unused kernel memory: 1272k freed
[4294683.050000] Adding 907664k swap on /dev/sda2. Priority:-1 extents:1
[4294683.389000] EXT3 FS on sda1, internal journal
next reply other threads:[~2005-07-09 9:33 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-07-09 9:34 Thiemo Seufer [this message]
2005-07-09 16:37 ` Current SGI Octane status Stanislaw Skowronek
2005-07-09 21:20 ` Thiemo Seufer
2005-07-11 22:27 ` Ralf Baechle
2005-07-12 7:21 ` Stanislaw Skowronek
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050709093403.GB1586@hattusa.textio \
--to=ths@networkno.de \
--cc=linux-mips@linux-mips.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.