From: raghavendra.koushik@neterion.com
To: jgarzik@pobox.com, netdev@oss.sgi.com
Cc: raghavendra.koushik@neterion.com,
ravinandan.arakali@neterion.com, leonid.grossman@neterion.com,
rapuru.sriram@neterion.com
Subject: [PATCH 2.6.13-rc4 9/13] S2io: Support for Xframe II NIC
Date: Wed, 3 Aug 2005 12:36:55 -0700 (PDT) [thread overview]
Message-ID: <20050803193655.CB51298355@linux.site> (raw)
Hi,
This patch provides basic support for the Xframe II adapter.
Includes the following changes:
1. New values to program XAUI interface.
2. Print the PCI/PCI-X mode(bus frequency, width).
3. Remove EOI from reset during intialization.
4. Enable all 8 PCCs if Xframe II adapter.
5. Programs the RLDRAM size depending on the device.
(Note: RLDRAM size on XFARME-I is 64Mb whereas on XFRAME-II it's 32 Mb).
6. Enable extended(64-bit) statistics counters.
7. Program timer interrupt duration based on PCI/PCI-X clock speed.
8. Not required to save/restore PCI config space before/after reset.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Raghavendra Koushik <raghavendra.koushik@neterion.com>
---
diff -uprN vanilla_linux/drivers/net/s2io-regs.h linux-2.6.13-rc4/drivers/net/s2io-regs.h
--- vanilla_linux/drivers/net/s2io-regs.h 2005-08-02 06:37:37.000000000 -0700
+++ linux-2.6.13-rc4/drivers/net/s2io-regs.h 2005-08-02 06:45:08.000000000 -0700
@@ -91,7 +91,21 @@ typedef struct _XENA_dev_config {
SERR_SOURCE_MC | \
SERR_SOURCE_XGXS)
- u8 unused_0[0x800 - 0x120];
+ u64 pci_mode;
+#define GET_PCI_MODE(val) ((val & vBIT(0xF, 0, 4)) >> 60)
+#define PCI_MODE_PCI_33 0
+#define PCI_MODE_PCI_66 0x1
+#define PCI_MODE_PCIX_M1_66 0x2
+#define PCI_MODE_PCIX_M1_100 0x3
+#define PCI_MODE_PCIX_M1_133 0x4
+#define PCI_MODE_PCIX_M2_66 0x5
+#define PCI_MODE_PCIX_M2_100 0x6
+#define PCI_MODE_PCIX_M2_133 0x7
+#define PCI_MODE_UNSUPPORTED BIT(0)
+#define PCI_MODE_32_BITS BIT(8)
+#define PCI_MODE_UNKNOWN_MODE BIT(9)
+
+ u8 unused_0[0x800 - 0x128];
/* PCI-X Controller registers */
u64 pic_int_status;
@@ -223,19 +237,16 @@ typedef struct _XENA_dev_config {
u64 xmsi_data;
u64 rx_mat;
+#define RX_MAT_SET(ring, msi) vBIT(msi, (8 * ring), 8)
u8 unused6[0x8];
- u64 tx_mat0_7;
- u64 tx_mat8_15;
- u64 tx_mat16_23;
- u64 tx_mat24_31;
- u64 tx_mat32_39;
- u64 tx_mat40_47;
- u64 tx_mat48_55;
- u64 tx_mat56_63;
+ u64 tx_mat0_n[0x8];
+#define TX_MAT_SET(fifo, msi) vBIT(msi, (8 * fifo), 8)
- u8 unused_1[0x10];
+ u8 unused_1[0x8];
+ u64 stat_byte_cnt;
+#define STAT_BC(n) vBIT(n,4,12)
/* Automated statistics collection */
u64 stat_cfg;
@@ -269,7 +280,12 @@ typedef struct _XENA_dev_config {
u64 gpio_control;
#define GPIO_CTRL_GPIO_0 BIT(8)
- u8 unused7[0x600];
+ u8 unused7_1[0x240 - 0x200];
+
+ u64 wreq_split_mask;
+#define WREQ_SPLIT_MASK_SET_MASK(val) vBIT(val, 52, 12)
+
+ u8 unused7_2[0x800 - 0x248];
/* TxDMA registers */
u64 txdma_int_status;
@@ -470,6 +486,7 @@ typedef struct _XENA_dev_config {
#define PRC_CTRL_NO_SNOOP (BIT(22)|BIT(23))
#define PRC_CTRL_NO_SNOOP_DESC BIT(22)
#define PRC_CTRL_NO_SNOOP_BUFF BIT(23)
+#define PRC_CTRL_BIMODAL_INTERRUPT BIT(37)
#define PRC_CTRL_RXD_BACKOFF_INTERVAL(val) vBIT(val,40,24)
u64 prc_alarm_action;
@@ -742,7 +759,19 @@ typedef struct _XENA_dev_config {
u64 mc_rldram_test_d1;
u8 unused24[0x300 - 0x288];
u64 mc_rldram_test_d2;
- u8 unused25[0x700 - 0x308];
+
+ u8 unused24_1[0x360 - 0x308];
+ u64 mc_rldram_ctrl;
+#define MC_RLDRAM_ENABLE_ODT BIT(7)
+
+ u8 unused24_2[0x640 - 0x368];
+ u64 mc_rldram_ref_per_herc;
+#define MC_RLDRAM_SET_REF_PERIOD(val) vBIT(val, 0, 16)
+
+ u8 unused24_3[0x660 - 0x648];
+ u64 mc_rldram_mrs_herc;
+
+ u8 unused25[0x700 - 0x668];
u64 mc_debug_ctrl;
u8 unused26[0x3000 - 0x2f08];
diff -uprN vanilla_linux/drivers/net/s2io.c linux-2.6.13-rc4/drivers/net/s2io.c
--- vanilla_linux/drivers/net/s2io.c 2005-08-02 06:37:37.000000000 -0700
+++ linux-2.6.13-rc4/drivers/net/s2io.c 2005-08-02 06:45:08.000000000 -0700
@@ -84,9 +84,10 @@ static inline int RXD_IS_UP2DT(RxD_t *rx
* problem, 600B, 600C, 600D, 640B, 640C and 640D.
* macro below identifies these cards given the subsystem_id.
*/
-#define CARDS_WITH_FAULTY_LINK_INDICATORS(subid) \
- (((subid >= 0x600B) && (subid <= 0x600D)) || \
- ((subid >= 0x640B) && (subid <= 0x640D))) ? 1 : 0
+#define CARDS_WITH_FAULTY_LINK_INDICATORS(dev_type, subid) \
+ (dev_type == XFRAME_I_DEVICE) ? \
+ ((((subid >= 0x600B) && (subid <= 0x600D)) || \
+ ((subid >= 0x640B) && (subid <= 0x640D))) ? 1 : 0) : 0
#define LINK_IS_UP(val64) (!(val64 & (ADAPTER_STATUS_RMAC_REMOTE_FAULT | \
ADAPTER_STATUS_RMAC_LOCAL_FAULT)))
@@ -207,7 +208,24 @@ static void s2io_vlan_rx_kill_vid(struct
#define SWITCH_SIGN 0xA5A5A5A5A5A5A5A5ULL
#define END_SIGN 0x0
-static u64 default_mdio_cfg[] = {
+static u64 herc_act_dtx_cfg[] = {
+ /* Set address */
+ 0x80000515BA750000ULL, 0x80000515BA7500E0ULL,
+ /* Write data */
+ 0x80000515BA750004ULL, 0x80000515BA7500E4ULL,
+ /* Set address */
+ 0x80010515003F0000ULL, 0x80010515003F00E0ULL,
+ /* Write data */
+ 0x80010515003F0004ULL, 0x80010515003F00E4ULL,
+ /* Set address */
+ 0x80020515F2100000ULL, 0x80020515F21000E0ULL,
+ /* Write data */
+ 0x80020515F2100004ULL, 0x80020515F21000E4ULL,
+ /* Done */
+ END_SIGN
+};
+
+static u64 xena_mdio_cfg[] = {
/* Reset PMA PLL */
0xC001010000000000ULL, 0xC0010100000000E0ULL,
0xC0010100008000E4ULL,
@@ -217,7 +235,7 @@ static u64 default_mdio_cfg[] = {
END_SIGN
};
-static u64 default_dtx_cfg[] = {
+static u64 xena_dtx_cfg[] = {
0x8000051500000000ULL, 0x80000515000000E0ULL,
0x80000515D93500E4ULL, 0x8001051500000000ULL,
0x80010515000000E0ULL, 0x80010515001E00E4ULL,
@@ -656,6 +674,87 @@ static void free_shared_mem(struct s2io_
}
/**
+ * s2io_verify_pci_mode -
+ */
+
+static int s2io_verify_pci_mode(nic_t *nic)
+{
+ XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0;
+ register u64 val64 = 0;
+ int mode;
+
+ val64 = readq(&bar0->pci_mode);
+ mode = (u8)GET_PCI_MODE(val64);
+
+ if ( val64 & PCI_MODE_UNKNOWN_MODE)
+ return -1; /* Unknown PCI mode */
+ return mode;
+}
+
+
+/**
+ * s2io_print_pci_mode -
+ */
+static int s2io_print_pci_mode(nic_t *nic)
+{
+ XENA_dev_config_t *bar0 = (XENA_dev_config_t *) nic->bar0;
+ register u64 val64 = 0;
+ int mode;
+ struct config_param *config = &nic->config;
+
+ val64 = readq(&bar0->pci_mode);
+ mode = (u8)GET_PCI_MODE(val64);
+
+ if ( val64 & PCI_MODE_UNKNOWN_MODE)
+ return -1; /* Unknown PCI mode */
+
+ if (val64 & PCI_MODE_32_BITS) {
+ DBG_PRINT(ERR_DBG, "%s: Device is on 32 bit ", nic->dev->name);
+ } else {
+ DBG_PRINT(ERR_DBG, "%s: Device is on 64 bit ", nic->dev->name);
+ }
+
+ switch(mode) {
+ case PCI_MODE_PCI_33:
+ DBG_PRINT(ERR_DBG, "33MHz PCI bus\n");
+ config->bus_speed = 33;
+ break;
+ case PCI_MODE_PCI_66:
+ DBG_PRINT(ERR_DBG, "66MHz PCI bus\n");
+ config->bus_speed = 133;
+ break;
+ case PCI_MODE_PCIX_M1_66:
+ DBG_PRINT(ERR_DBG, "66MHz PCIX(M1) bus\n");
+ config->bus_speed = 133; /* Herc doubles the clock rate */
+ break;
+ case PCI_MODE_PCIX_M1_100:
+ DBG_PRINT(ERR_DBG, "100MHz PCIX(M1) bus\n");
+ config->bus_speed = 200;
+ break;
+ case PCI_MODE_PCIX_M1_133:
+ DBG_PRINT(ERR_DBG, "133MHz PCIX(M1) bus\n");
+ config->bus_speed = 266;
+ break;
+ case PCI_MODE_PCIX_M2_66:
+ DBG_PRINT(ERR_DBG, "133MHz PCIX(M2) bus\n");
+ config->bus_speed = 133;
+ break;
+ case PCI_MODE_PCIX_M2_100:
+ DBG_PRINT(ERR_DBG, "200MHz PCIX(M2) bus\n");
+ config->bus_speed = 200;
+ break;
+ case PCI_MODE_PCIX_M2_133:
+ DBG_PRINT(ERR_DBG, "266MHz PCIX(M2) bus\n");
+ config->bus_speed = 266;
+ break;
+ default:
+ return -1; /* Unsupported bus speed */
+ }
+
+ return mode;
+}
+
+/**
* init_nic - Initialization of hardware
* @nic: device peivate variable
* Description: The function sequentially configures every block
@@ -687,6 +786,16 @@ static int init_nic(struct s2io_nic *nic
return -1;
}
+ /*
+ * Herc requires EOI to be removed from reset before XGXS, so..
+ */
+ if (nic->device_type & XFRAME_II_DEVICE) {
+ val64 = 0xA500000000ULL;
+ writeq(val64, &bar0->sw_reset);
+ msleep(500);
+ val64 = readq(&bar0->sw_reset);
+ }
+
/* Remove XGXS from reset state */
val64 = 0;
writeq(val64, &bar0->sw_reset);
@@ -718,41 +827,51 @@ static int init_nic(struct s2io_nic *nic
* of 64 bit values into two registers in a particular
* sequence. Hence a macro 'SWITCH_SIGN' has been defined
* which will be defined in the array of configuration values
- * (default_dtx_cfg & default_mdio_cfg) at appropriate places
+ * (xena_dtx_cfg & xena_mdio_cfg) at appropriate places
* to switch writing from one regsiter to another. We continue
* writing these values until we encounter the 'END_SIGN' macro.
* For example, After making a series of 21 writes into
* dtx_control register the 'SWITCH_SIGN' appears and hence we
* start writing into mdio_control until we encounter END_SIGN.
*/
- while (1) {
- dtx_cfg:
- while (default_dtx_cfg[dtx_cnt] != END_SIGN) {
- if (default_dtx_cfg[dtx_cnt] == SWITCH_SIGN) {
- dtx_cnt++;
- goto mdio_cfg;
- }
- SPECIAL_REG_WRITE(default_dtx_cfg[dtx_cnt],
+ if (nic->device_type & XFRAME_II_DEVICE) {
+ while (herc_act_dtx_cfg[dtx_cnt] != END_SIGN) {
+ SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
&bar0->dtx_control, UF);
- val64 = readq(&bar0->dtx_control);
+ if (dtx_cnt & 0x1)
+ msleep(1); /* Necessary!! */
dtx_cnt++;
}
- mdio_cfg:
- while (default_mdio_cfg[mdio_cnt] != END_SIGN) {
- if (default_mdio_cfg[mdio_cnt] == SWITCH_SIGN) {
+ } else {
+ while (1) {
+ dtx_cfg:
+ while (xena_dtx_cfg[dtx_cnt] != END_SIGN) {
+ if (xena_dtx_cfg[dtx_cnt] == SWITCH_SIGN) {
+ dtx_cnt++;
+ goto mdio_cfg;
+ }
+ SPECIAL_REG_WRITE(xena_dtx_cfg[dtx_cnt],
+ &bar0->dtx_control, UF);
+ val64 = readq(&bar0->dtx_control);
+ dtx_cnt++;
+ }
+ mdio_cfg:
+ while (xena_mdio_cfg[mdio_cnt] != END_SIGN) {
+ if (xena_mdio_cfg[mdio_cnt] == SWITCH_SIGN) {
+ mdio_cnt++;
+ goto dtx_cfg;
+ }
+ SPECIAL_REG_WRITE(xena_mdio_cfg[mdio_cnt],
+ &bar0->mdio_control, UF);
+ val64 = readq(&bar0->mdio_control);
mdio_cnt++;
+ }
+ if ((xena_dtx_cfg[dtx_cnt] == END_SIGN) &&
+ (xena_mdio_cfg[mdio_cnt] == END_SIGN)) {
+ break;
+ } else {
goto dtx_cfg;
}
- SPECIAL_REG_WRITE(default_mdio_cfg[mdio_cnt],
- &bar0->mdio_control, UF);
- val64 = readq(&bar0->mdio_control);
- mdio_cnt++;
- }
- if ((default_dtx_cfg[dtx_cnt] == END_SIGN) &&
- (default_mdio_cfg[mdio_cnt] == END_SIGN)) {
- break;
- } else {
- goto dtx_cfg;
}
}
@@ -803,7 +922,8 @@ static int init_nic(struct s2io_nic *nic
* Disable 4 PCCs for Xena1, 2 and 3 as per H/W bug
* SXE-008 TRANSMIT DMA ARBITRATION ISSUE.
*/
- if (get_xena_rev_id(nic->pdev) < 4)
+ if ((nic->device_type == XFRAME_I_DEVICE) &&
+ (get_xena_rev_id(nic->pdev) < 4))
writeq(PCC_ENABLE_FOUR, &bar0->pcc_enable);
val64 = readq(&bar0->tx_fifo_partition_0);
@@ -833,7 +953,11 @@ static int init_nic(struct s2io_nic *nic
* configured Rings.
*/
val64 = 0;
- mem_size = 64;
+ if (nic->device_type & XFRAME_II_DEVICE)
+ mem_size = 32;
+ else
+ mem_size = 64;
+
for (i = 0; i < config->rx_ring_num; i++) {
switch (i) {
case 0:
@@ -1116,6 +1240,11 @@ static int init_nic(struct s2io_nic *nic
/* Program statistics memory */
writeq(mac_control->stats_mem_phy, &bar0->stat_addr);
+ if (nic->device_type == XFRAME_II_DEVICE) {
+ val64 = STAT_BC(0x320);
+ writeq(val64, &bar0->stat_byte_cnt);
+ }
+
/*
* Initializing the sampling rate for the device to calculate the
* bandwidth utilization.
@@ -1134,12 +1263,18 @@ static int init_nic(struct s2io_nic *nic
* 250 interrupts per sec. Continuous interrupts are enabled
* by default.
*/
- val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078) |
- TTI_DATA1_MEM_TX_URNG_A(0xA) |
+ if (nic->device_type == XFRAME_II_DEVICE) {
+ int count = (nic->config.bus_speed * 125)/2;
+ val64 = TTI_DATA1_MEM_TX_TIMER_VAL(count);
+ } else {
+
+ val64 = TTI_DATA1_MEM_TX_TIMER_VAL(0x2078);
+ }
+ val64 |= TTI_DATA1_MEM_TX_URNG_A(0xA) |
TTI_DATA1_MEM_TX_URNG_B(0x10) |
TTI_DATA1_MEM_TX_URNG_C(0x30) | TTI_DATA1_MEM_TX_TIMER_AC_EN;
- if (use_continuous_tx_intrs)
- val64 |= TTI_DATA1_MEM_TX_TIMER_CI_EN;
+ if (use_continuous_tx_intrs)
+ val64 |= TTI_DATA1_MEM_TX_TIMER_CI_EN;
writeq(val64, &bar0->tti_data1_mem);
val64 = TTI_DATA2_MEM_TX_UFC_A(0x10) |
@@ -1171,9 +1306,19 @@ static int init_nic(struct s2io_nic *nic
time++;
}
+
/* RTI Initialization */
- val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF) |
- RTI_DATA1_MEM_RX_URNG_A(0xA) |
+ if (nic->device_type == XFRAME_II_DEVICE) {
+ /*
+ * Programmed to generate Apprx 500 Intrs per
+ * second
+ */
+ int count = (nic->config.bus_speed * 125)/4;
+ val64 = RTI_DATA1_MEM_RX_TIMER_VAL(count);
+ } else {
+ val64 = RTI_DATA1_MEM_RX_TIMER_VAL(0xFFF);
+ }
+ val64 |= RTI_DATA1_MEM_RX_URNG_A(0xA) |
RTI_DATA1_MEM_RX_URNG_B(0x10) |
RTI_DATA1_MEM_RX_URNG_C(0x30) | RTI_DATA1_MEM_RX_TIMER_AC_EN;
@@ -1267,6 +1412,15 @@ static int init_nic(struct s2io_nic *nic
val64 |= PIC_CNTL_SHARED_SPLITS(shared_splits);
writeq(val64, &bar0->pic_control);
+ /*
+ * Programming the Herc to split every write transaction
+ * that does not start on an ADB to reduce disconnects.
+ */
+ if (nic->device_type == XFRAME_II_DEVICE) {
+ val64 = WREQ_SPLIT_MASK_SET_MASK(255);
+ writeq(val64, &bar0->wreq_split_mask);
+ }
+
return SUCCESS;
}
@@ -1509,18 +1663,18 @@ static void en_dis_able_nic_intrs(struct
}
}
-static int check_prc_pcc_state(u64 val64, int flag, int rev_id)
+static int check_prc_pcc_state(u64 val64, int flag, int rev_id, int herc)
{
int ret = 0;
if (flag == FALSE) {
- if (rev_id >= 4) {
+ if ((!herc && (rev_id >= 4)) || herc) {
if (!(val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) &&
((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
ret = 1;
}
- } else {
+ }else {
if (!(val64 & ADAPTER_STATUS_RMAC_PCC_FOUR_IDLE) &&
((val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ==
ADAPTER_STATUS_RC_PRC_QUIESCENT)) {
@@ -1528,7 +1682,7 @@ static int check_prc_pcc_state(u64 val64
}
}
} else {
- if (rev_id >= 4) {
+ if ((!herc && (rev_id >= 4)) || herc) {
if (((val64 & ADAPTER_STATUS_RMAC_PCC_IDLE) ==
ADAPTER_STATUS_RMAC_PCC_IDLE) &&
(!(val64 & ADAPTER_STATUS_RC_PRC_QUIESCENT) ||
@@ -1564,10 +1718,11 @@ static int check_prc_pcc_state(u64 val64
static int verify_xena_quiescence(nic_t *sp, u64 val64, int flag)
{
- int ret = 0;
+ int ret = 0, herc;
u64 tmp64 = ~((u64) val64);
int rev_id = get_xena_rev_id(sp->pdev);
+ herc = (sp->device_type == XFRAME_II_DEVICE);
if (!
(tmp64 &
(ADAPTER_STATUS_TDMA_READY | ADAPTER_STATUS_RDMA_READY |
@@ -1575,7 +1730,7 @@ static int verify_xena_quiescence(nic_t
ADAPTER_STATUS_PIC_QUIESCENT | ADAPTER_STATUS_MC_DRAM_READY |
ADAPTER_STATUS_MC_QUEUES_READY | ADAPTER_STATUS_M_PLL_LOCK |
ADAPTER_STATUS_P_PLL_LOCK))) {
- ret = check_prc_pcc_state(val64, flag, rev_id);
+ ret = check_prc_pcc_state(val64, flag, rev_id, herc);
}
return ret;
@@ -1706,7 +1861,8 @@ static int start_nic(struct s2io_nic *ni
/* SXE-002: Initialize link and activity LED */
subid = nic->pdev->subsystem_device;
- if ((subid & 0xFF) >= 0x07) {
+ if (((subid & 0xFF) >= 0x07) &&
+ (nic->device_type == XFRAME_I_DEVICE)) {
val64 = readq(&bar0->gpio_control);
val64 |= 0x0000800000000000ULL;
writeq(val64, &bar0->gpio_control);
@@ -2541,9 +2697,12 @@ void s2io_reset(nic_t * sp)
*/
msleep(250);
+ if (!(sp->device_type & XFRAME_II_DEVICE)) {
/* Restore the PCI state saved during initializarion. */
- pci_restore_state(sp->pdev);
-
+ pci_restore_state(sp->pdev);
+ } else {
+ pci_set_master(sp->pdev);
+ }
s2io_init_pci(sp);
msleep(250);
@@ -2568,7 +2727,8 @@ void s2io_reset(nic_t * sp)
/* SXE-002: Configure link and activity LED to turn it off */
subid = sp->pdev->subsystem_device;
- if ((subid & 0xFF) >= 0x07) {
+ if (((subid & 0xFF) >= 0x07) &&
+ (sp->device_type == XFRAME_I_DEVICE)) {
val64 = readq(&bar0->gpio_control);
val64 |= 0x0000800000000000ULL;
writeq(val64, &bar0->gpio_control);
@@ -2576,6 +2736,15 @@ void s2io_reset(nic_t * sp)
writeq(val64, (void __iomem *) ((u8 *) bar0 + 0x2700));
}
+ /*
+ * Clear spurious ECC interrupts that would have occured on
+ * XFRAME II cards after reset.
+ */
+ if (sp->device_type == XFRAME_II_DEVICE) {
+ val64 = readq(&bar0->pcc_err_reg);
+ writeq(val64, &bar0->pcc_err_reg);
+ }
+
sp->device_enabled_once = FALSE;
}
@@ -3463,7 +3632,8 @@ static void s2io_phy_id(unsigned long da
u16 subid;
subid = sp->pdev->subsystem_device;
- if ((subid & 0xFF) >= 0x07) {
+ if ((sp->device_type == XFRAME_II_DEVICE) ||
+ ((subid & 0xFF) >= 0x07)) {
val64 = readq(&bar0->gpio_control);
val64 ^= GPIO_CTRL_GPIO_0;
writeq(val64, &bar0->gpio_control);
@@ -3500,7 +3670,8 @@ static int s2io_ethtool_idnic(struct net
subid = sp->pdev->subsystem_device;
last_gpio_ctrl_val = readq(&bar0->gpio_control);
- if ((subid & 0xFF) < 0x07) {
+ if ((sp->device_type == XFRAME_I_DEVICE) &&
+ ((subid & 0xFF) < 0x07)) {
val64 = readq(&bar0->adapter_control);
if (!(val64 & ADAPTER_CNTL_EN)) {
printk(KERN_ERR
@@ -3520,7 +3691,7 @@ static int s2io_ethtool_idnic(struct net
msleep_interruptible(MAX_FLICKER_TIME);
del_timer_sync(&sp->id_timer);
- if (CARDS_WITH_FAULTY_LINK_INDICATORS(subid)) {
+ if (CARDS_WITH_FAULTY_LINK_INDICATORS(sp->device_type, subid)) {
writeq(last_gpio_ctrl_val, &bar0->gpio_control);
last_gpio_ctrl_val = readq(&bar0->gpio_control);
}
@@ -4134,44 +4305,91 @@ static void s2io_get_ethtool_stats(struc
StatInfo_t *stat_info = sp->mac_control.stats_info;
s2io_updt_stats(sp);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_data_octets);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_data_octets_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_data_octets);
tmp_stats[i++] = le64_to_cpu(stat_info->tmac_drop_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_mcst_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_bcst_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_mcst_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_mcst_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_bcst_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_bcst_frms);
tmp_stats[i++] = le64_to_cpu(stat_info->tmac_pause_ctrl_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_any_err_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_any_err_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_any_err_frms);
tmp_stats[i++] = le64_to_cpu(stat_info->tmac_vld_ip_octets);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_vld_ip);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_drop_ip);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_icmp);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_rst_tcp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_vld_ip_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_vld_ip);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_drop_ip_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_drop_ip);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_icmp_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_icmp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->tmac_rst_tcp_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_rst_tcp);
tmp_stats[i++] = le64_to_cpu(stat_info->tmac_tcp);
- tmp_stats[i++] = le32_to_cpu(stat_info->tmac_udp);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_vld_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_data_octets);
+ tmp_stats[i++] = (u64)le32_to_cpu(stat_info->tmac_udp_oflow) << 32 |
+ le32_to_cpu(stat_info->tmac_udp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_vld_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_vld_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_data_octets_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_data_octets);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_fcs_err_frms);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_drop_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_vld_mcst_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_vld_bcst_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_vld_mcst_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_vld_mcst_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_vld_bcst_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_vld_bcst_frms);
tmp_stats[i++] = le32_to_cpu(stat_info->rmac_in_rng_len_err_frms);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_long_frms);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_pause_ctrl_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_discarded_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_usized_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_osized_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_frag_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_jabber_frms);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_ip);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_discarded_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_discarded_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_usized_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_usized_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_osized_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_osized_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_frag_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_frag_frms);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_jabber_frms_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_jabber_frms);
+ tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_ip_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_ip);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_ip_octets);
tmp_stats[i++] = le32_to_cpu(stat_info->rmac_hdr_err_ip);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_drop_ip);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_icmp);
+ tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_drop_ip_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_drop_ip);
+ tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_icmp_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_icmp);
tmp_stats[i++] = le64_to_cpu(stat_info->rmac_tcp);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_udp);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_drp_udp);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_pause_cnt);
- tmp_stats[i++] = le32_to_cpu(stat_info->rmac_accepted_ip);
+ tmp_stats[i++] = (u64)le32_to_cpu(stat_info->rmac_udp_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_udp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_err_drp_udp_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_err_drp_udp);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_pause_cnt_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_pause_cnt);
+ tmp_stats[i++] =
+ (u64)le32_to_cpu(stat_info->rmac_accepted_ip_oflow) << 32 |
+ le32_to_cpu(stat_info->rmac_accepted_ip);
tmp_stats[i++] = le32_to_cpu(stat_info->rmac_err_tcp);
tmp_stats[i++] = 0;
tmp_stats[i++] = stat_info->sw_stat.single_ecc_errs;
@@ -4401,7 +4619,8 @@ static void s2io_set_link(unsigned long
val64 = readq(&bar0->adapter_control);
val64 |= ADAPTER_CNTL_EN;
writeq(val64, &bar0->adapter_control);
- if (CARDS_WITH_FAULTY_LINK_INDICATORS(subid)) {
+ if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
+ subid)) {
val64 = readq(&bar0->gpio_control);
val64 |= GPIO_CTRL_GPIO_0;
writeq(val64, &bar0->gpio_control);
@@ -4423,7 +4642,8 @@ static void s2io_set_link(unsigned long
}
s2io_link(nic, LINK_UP);
} else {
- if (CARDS_WITH_FAULTY_LINK_INDICATORS(subid)) {
+ if (CARDS_WITH_FAULTY_LINK_INDICATORS(nic->device_type,
+ subid)) {
val64 = readq(&bar0->gpio_control);
val64 &= ~GPIO_CTRL_GPIO_0;
writeq(val64, &bar0->gpio_control);
@@ -4708,7 +4928,6 @@ static int rx_osm_handler(ring_info_t *r
netif_rx(skb);
}
#endif
-
dev->last_rx = jiffies;
atomic_dec(&sp->rx_bufs_left[ring_no]);
return SUCCESS;
@@ -4842,6 +5061,7 @@ s2io_init_nic(struct pci_dev *pdev, cons
u16 subid;
mac_info_t *mac_control;
struct config_param *config;
+ int mode;
#ifdef CONFIG_S2IO_NAPI
DBG_PRINT(ERR_DBG, "NAPI support has been enabled\n");
@@ -4898,6 +5118,12 @@ s2io_init_nic(struct pci_dev *pdev, cons
sp->high_dma_flag = dma_flag;
sp->device_enabled_once = FALSE;
+ if ((pdev->device == PCI_DEVICE_ID_HERC_WIN) ||
+ (pdev->device == PCI_DEVICE_ID_HERC_UNI))
+ sp->device_type = XFRAME_II_DEVICE;
+ else
+ sp->device_type = XFRAME_I_DEVICE;
+
/* Initialize some PCI/PCI-X fields of the NIC. */
s2io_init_pci(sp);
@@ -5033,7 +5259,9 @@ s2io_init_nic(struct pci_dev *pdev, cons
INIT_WORK(&sp->set_link_task,
(void (*)(void *)) s2io_set_link, sp);
- pci_save_state(sp->pdev);
+ if (!(sp->device_type & XFRAME_II_DEVICE)) {
+ pci_save_state(sp->pdev);
+ }
/* Setting swapper control on the NIC, for proper reset operation */
if (s2io_set_swapper(sp)) {
@@ -5043,12 +5271,26 @@ s2io_init_nic(struct pci_dev *pdev, cons
goto set_swap_failed;
}
- /*
- * Fix for all "FFs" MAC address problems observed on
- * Alpha platforms
- */
- fix_mac_address(sp);
- s2io_reset(sp);
+ /* Verify if the Herc works on the slot its placed into */
+ if (sp->device_type & XFRAME_II_DEVICE) {
+ mode = s2io_verify_pci_mode(sp);
+ if (mode < 0) {
+ DBG_PRINT(ERR_DBG, "%s: ", __FUNCTION__);
+ DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode\n");
+ ret = -EBADSLT;
+ goto set_swap_failed;
+ }
+ }
+
+ /* Not needed for Herc */
+ if (sp->device_type & XFRAME_I_DEVICE) {
+ /*
+ * Fix for all "FFs" MAC address problems observed on
+ * Alpha platforms
+ */
+ fix_mac_address(sp);
+ s2io_reset(sp);
+ }
/*
* MAC address initialization.
@@ -5073,22 +5315,13 @@ s2io_init_nic(struct pci_dev *pdev, cons
sp->def_mac_addr[0].mac_addr[5] = (u8) (mac_down >> 16);
sp->def_mac_addr[0].mac_addr[4] = (u8) (mac_down >> 24);
- DBG_PRINT(INIT_DBG,
- "DEFAULT MAC ADDR:0x%02x-%02x-%02x-%02x-%02x-%02x\n",
- sp->def_mac_addr[0].mac_addr[0],
- sp->def_mac_addr[0].mac_addr[1],
- sp->def_mac_addr[0].mac_addr[2],
- sp->def_mac_addr[0].mac_addr[3],
- sp->def_mac_addr[0].mac_addr[4],
- sp->def_mac_addr[0].mac_addr[5]);
-
/* Set the factory defined MAC address initially */
dev->addr_len = ETH_ALEN;
memcpy(dev->dev_addr, sp->def_mac_addr, ETH_ALEN);
/*
* Initialize the tasklet status and link state flags
- * and the card statte parameter
+ * and the card state parameter
*/
atomic_set(&(sp->card_state), 0);
sp->tasklet_status = 0;
@@ -5123,9 +5356,46 @@ s2io_init_nic(struct pci_dev *pdev, cons
goto register_failed;
}
+ if (sp->device_type & XFRAME_II_DEVICE) {
+ DBG_PRINT(ERR_DBG, "%s: Neterion Xframe II 10GbE adapter ",
+ dev->name);
+ DBG_PRINT(ERR_DBG, "(rev %d), Driver %s\n",
+ get_xena_rev_id(sp->pdev),
+ s2io_driver_version);
+ DBG_PRINT(ERR_DBG, "MAC ADDR: %02x:%02x:%02x:%02x:%02x:%02x\n",
+ sp->def_mac_addr[0].mac_addr[0],
+ sp->def_mac_addr[0].mac_addr[1],
+ sp->def_mac_addr[0].mac_addr[2],
+ sp->def_mac_addr[0].mac_addr[3],
+ sp->def_mac_addr[0].mac_addr[4],
+ sp->def_mac_addr[0].mac_addr[5]);
+ int mode = s2io_print_pci_mode(sp);
+ if (mode < 0) {
+ DBG_PRINT(ERR_DBG, " Unsupported PCI bus mode ");
+ ret = -EBADSLT;
+ goto set_swap_failed;
+ }
+ } else {
+ DBG_PRINT(ERR_DBG, "%s: Neterion Xframe I 10GbE adapter ",
+ dev->name);
+ DBG_PRINT(ERR_DBG, "(rev %d), Driver %s\n",
+ get_xena_rev_id(sp->pdev),
+ s2io_driver_version);
+ DBG_PRINT(ERR_DBG, "MAC ADDR: %02x:%02x:%02x:%02x:%02x:%02x\n",
+ sp->def_mac_addr[0].mac_addr[0],
+ sp->def_mac_addr[0].mac_addr[1],
+ sp->def_mac_addr[0].mac_addr[2],
+ sp->def_mac_addr[0].mac_addr[3],
+ sp->def_mac_addr[0].mac_addr[4],
+ sp->def_mac_addr[0].mac_addr[5]);
+ }
+
/* Initialize device name */
strcpy(sp->name, dev->name);
- strcat(sp->name, ": Neterion Xframe I 10GbE adapter");
+ if (sp->device_type & XFRAME_II_DEVICE)
+ strcat(sp->name, ": Neterion Xframe II 10GbE adapter");
+ else
+ strcat(sp->name, ": Neterion Xframe I 10GbE adapter");
/*
* Make Link state as off at this point, when the Link change
diff -uprN vanilla_linux/drivers/net/s2io.h linux-2.6.13-rc4/drivers/net/s2io.h
--- vanilla_linux/drivers/net/s2io.h 2005-08-02 06:37:37.000000000 -0700
+++ linux-2.6.13-rc4/drivers/net/s2io.h 2005-08-02 06:45:08.000000000 -0700
@@ -201,6 +201,67 @@ typedef struct stat_block {
u32 rxf_wr_cnt;
u32 txf_rd_cnt;
+/* Tx MAC statistics overflow counters. */
+ u32 tmac_data_octets_oflow;
+ u32 tmac_frms_oflow;
+ u32 tmac_bcst_frms_oflow;
+ u32 tmac_mcst_frms_oflow;
+ u32 tmac_ucst_frms_oflow;
+ u32 tmac_ttl_octets_oflow;
+ u32 tmac_any_err_frms_oflow;
+ u32 tmac_nucst_frms_oflow;
+ u64 tmac_vlan_frms;
+ u32 tmac_drop_ip_oflow;
+ u32 tmac_vld_ip_oflow;
+ u32 tmac_rst_tcp_oflow;
+ u32 tmac_icmp_oflow;
+ u32 tpa_unknown_protocol;
+ u32 tmac_udp_oflow;
+ u32 reserved_10;
+ u32 tpa_parse_failure;
+
+/* Rx MAC Statistics overflow counters. */
+ u32 rmac_data_octets_oflow;
+ u32 rmac_vld_frms_oflow;
+ u32 rmac_vld_bcst_frms_oflow;
+ u32 rmac_vld_mcst_frms_oflow;
+ u32 rmac_accepted_ucst_frms_oflow;
+ u32 rmac_ttl_octets_oflow;
+ u32 rmac_discarded_frms_oflow;
+ u32 rmac_accepted_nucst_frms_oflow;
+ u32 rmac_usized_frms_oflow;
+ u32 rmac_drop_events_oflow;
+ u32 rmac_frag_frms_oflow;
+ u32 rmac_osized_frms_oflow;
+ u32 rmac_ip_oflow;
+ u32 rmac_jabber_frms_oflow;
+ u32 rmac_icmp_oflow;
+ u32 rmac_drop_ip_oflow;
+ u32 rmac_err_drp_udp_oflow;
+ u32 rmac_udp_oflow;
+ u32 reserved_11;
+ u32 rmac_pause_cnt_oflow;
+ u64 rmac_ttl_1519_4095_frms;
+ u64 rmac_ttl_4096_8191_frms;
+ u64 rmac_ttl_8192_max_frms;
+ u64 rmac_ttl_gt_max_frms;
+ u64 rmac_osized_alt_frms;
+ u64 rmac_jabber_alt_frms;
+ u64 rmac_gt_max_alt_frms;
+ u64 rmac_vlan_frms;
+ u32 rmac_len_discard;
+ u32 rmac_fcs_discard;
+ u32 rmac_pf_discard;
+ u32 rmac_da_discard;
+ u32 rmac_red_discard;
+ u32 rmac_rts_discard;
+ u32 reserved_12;
+ u32 rmac_ingm_full_discard;
+ u32 reserved_13;
+ u32 rmac_accepted_ip_oflow;
+ u32 reserved_14;
+ u32 link_fault_cnt;
+
/* Software statistics maintained by driver */
swStat_t sw_stat;
} StatInfo_t;
@@ -690,6 +751,9 @@ struct s2io_nic {
atomic_t card_state;
volatile unsigned long link_state;
struct vlan_group *vlgrp;
+#define XFRAME_I_DEVICE 1
+#define XFRAME_II_DEVICE 2
+ u8 device_type;
spinlock_t rx_lock;
atomic_t isr_cnt;
reply other threads:[~2005-08-03 19:36 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050803193655.CB51298355@linux.site \
--to=raghavendra.koushik@neterion.com \
--cc=jgarzik@pobox.com \
--cc=leonid.grossman@neterion.com \
--cc=netdev@oss.sgi.com \
--cc=rapuru.sriram@neterion.com \
--cc=ravinandan.arakali@neterion.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.