All of lore.kernel.org
 help / color / mirror / Atom feed
From: Ladislav Michl <ladis@linux-mips.org>
To: u-boot@lists.denx.de
Subject: [U-Boot-Users] [PATCH] Update VoiceBlue to use new MTD flash partitioning methods
Date: Tue, 16 Aug 2005 12:07:51 +0200	[thread overview]
Message-ID: <20050816100751.GA22043@orphique> (raw)
In-Reply-To: <20050807230847.D54D9352BD9@atlas.denx.de>

On Mon, Aug 08, 2005 at 01:08:47AM +0200, Wolfgang Denk wrote:
> Among the modified and not tested targets there is a group of targets
> which were implementing their custom multi-partition scheme. This was
> mostly duplicating jffs2_part_info() routine  code.  Introducing  the
> new  common  scheme  required removing this duplicated code, so those
> targets should be especially carefully  tested  by  the  board  main-
> tainers.  Target  list  that  require  special  attention:  xsengine,
> voiceblue, ...

Hi Wolfgang,

support for VoiceBlue board is broken in 1.1.3, because it needs
partitions (well, my fault. I shouldn't be on holidays ;-)). Patch below
fixes that (and a bit more).

Best regards,
	ladis

CHANGELOG
* VoiceBlue update: use new MTD flash partitioning methods, use more
  reasonable TEXT_BASE, update default environment and enable keyed
  autoboot.

Signed-off-by: Ladislav Michl <ladis@linux-mips.org>

diff --git a/board/voiceblue/config.mk b/board/voiceblue/config.mk
--- a/board/voiceblue/config.mk
+++ b/board/voiceblue/config.mk
@@ -12,5 +12,5 @@ ifeq ($(VOICEBLUE_SMALL_FLASH),y)
 TEXT_BASE = 0x20012000
 else
 # Running in SDRAM...
-TEXT_BASE = 0x13000000
+TEXT_BASE = 0x13FD0000
 endif
diff --git a/include/configs/voiceblue.h b/include/configs/voiceblue.h
--- a/include/configs/voiceblue.h
+++ b/include/configs/voiceblue.h
@@ -47,6 +47,8 @@
 #define CONFIG_SETUP_MEMORY_TAGS	1
 #define CONFIG_INITRD_TAG		1
 
+#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+
 /*
  * Physical Memory Map
  */
@@ -94,7 +96,6 @@
 
 #define CONFIG_ENV_OVERWRITE
 
-#define CFG_JFFS_CUSTOM_PART	/* see board/voiceblue/jffs2parts.c */
 #endif
 
 /*
@@ -104,9 +105,11 @@
 #ifdef VOICEBLUE_SMALL_FLASH
 #define CFG_MALLOC_LEN		(SZ_64K - CFG_GBL_DATA_SIZE)
 #define CONFIG_STACKSIZE	SZ_8K
+#define PHYS_SDRAM_1_RESERVED	0
 #else
 #define CFG_MALLOC_LEN		SZ_4M
 #define CONFIG_STACKSIZE	SZ_1M
+#define PHYS_SDRAM_1_RESERVED	(CFG_MONITOR_LEN + CFG_MALLOC_LEN + CONFIG_STACKSIZE)
 #endif
 
 /*
@@ -174,6 +177,7 @@
 #define CONFIG_BOOTCOMMAND	"run nboot"
 #define CONFIG_PREBOOT		"run setup"
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"silent=1\0"						\
 	"ospart=0\0"						\
 	"swapos=no\0"						\
 	"setpart="						\
@@ -185,15 +189,37 @@
 	"fi\0"							\
 	"setup=setenv bootargs console=ttyS0,$baudrate "	\
 		"mtdparts=$mtdparts\0"				\
-	"nfsargs=run setpart; setenv bootargs $bootargs "	\
-		"root=/dev/nfs ip=dhcp\0"			\
+	"nfsargs=setenv bootargs $bootargs "			\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off " \
+		"nfsroot=$rootpath root=/dev/nfs\0"		\
 	"flashargs=run setpart; setenv bootargs $bootargs "	\
 		"root=/dev/mtdblock$partition ro "		\
 		"rootfstype=jffs2\0"				\
-	"nboot=run nfsargs; bootp; tftp; bootm\0"		\
-	"fboot=run flashargs; fsload /boot/uImage; bootm\0"
+	"initrdargs=setenv bootargs $bootargs "			\
+		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname::off\0" \
+	"fboot=run flashargs; fsload /boot/uImage; bootm\0"	\
+	"iboot=bootp; run initrdargs; tftp; bootm\0"		\
+	"nboot=bootp; run nfsargs; tftp; bootm\0"
 #endif
 
+#ifndef VOICEBLUE_SMALL_FLASH
+#define CONFIG_SILENT_CONSOLE		1	/* enable silent startup */
+
+#if 1	/* feel free to disable for development */
+#define CONFIG_AUTOBOOT_KEYED		/* Enable password protection	*/
+#define CONFIG_AUTOBOOT_PROMPT	"\nVoiceBlue Enterprise - booting...\n"
+#define CONFIG_AUTOBOOT_DELAY_STR	"."	/* 1st "password"	*/
+#endif
+
+/*
+ * JFFS2 partitions (mtdparts command line support)
+ */
+#define CONFIG_JFFS2_CMDLINE
+#define MTDIDS_DEFAULT		"nor0=omapflash.0"
+#define MTDPARTS_DEFAULT	"mtdparts=omapflash.0:128k(uboot),64k(env),64k(r_env),16256k(data1),-(data2)"
+
+#endif	/* VOICEBLUE_SMALL_FLASH */
+
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
@@ -213,7 +239,7 @@
 #define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
 #define CFG_MEMTEST_START	PHYS_SDRAM_1
-#define CFG_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE
+#define CFG_MEMTEST_END		PHYS_SDRAM_1 + PHYS_SDRAM_1_SIZE - PHYS_SDRAM_1_RESERVED
 
 #undef	CFG_CLKS_IN_HZ		/* everything, incl board info, in Hz */
 
@@ -247,22 +273,4 @@
 
 #define VOICEBLUE_LED_REG	0x04030000
 
-/*
- * JFFS2 partitions
- *
- */
-/* No command line, one static partition */
-#undef CONFIG_JFFS2_CMDLINE
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00040000
-
-/* mtdparts command line support */
-/* Note: fake mtd_id used, no linux mtd map file */
-/*
-#define CONFIG_JFFS2_CMDLINE
-#define MTDIDS_DEFAULT		"nor0=voiceblue-0"
-#define MTDPARTS_DEFAULT	"mtdparts=voiceblue-0:128k(uboot),64k(env),64k(renv),-(jffs2)"
-*/
-
 #endif	/* __CONFIG_H */

  reply	other threads:[~2005-08-16 10:07 UTC|newest]

Thread overview: 3+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2005-08-07 23:08 [U-Boot-Users] NOTE: New MTD flash partitioning methods Wolfgang Denk
2005-08-16 10:07 ` Ladislav Michl [this message]
2006-06-19 22:15   ` [U-Boot-Users] [PATCH] Update VoiceBlue to use new " Wolfgang Denk

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20050816100751.GA22043@orphique \
    --to=ladis@linux-mips.org \
    --cc=u-boot@lists.denx.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.