From: Norbert Kiesel <nkiesel@tbdnetworks.com>
To: Linus Torvalds <torvalds@osdl.org>
Cc: linux-kernel@vger.kernel.org
Subject: Re: 2.6.13.1 locks machine after some time, 2.6.12.5 work fine
Date: Mon, 12 Sep 2005 20:38:14 -0700 [thread overview]
Message-ID: <20050913033814.GA879@tbdnetworks.com> (raw)
In-Reply-To: <Pine.LNX.4.58.0509121950340.3266@g5.osdl.org>
[-- Attachment #1: Type: text/plain, Size: 1355 bytes --]
Hi,
diff is appended. Regarding the -rc3 and friends, currently I can't as
I jumped directly from 12.5 to 13. This is my desktop at work, so I
try to keep it somewhat stable. However, if you have a guess which
versions to try, I can give it a spin. It takes some time though to
test, as the lockup normally only happens after 1 hour or so (although
I could propably speed this up by doing lots of disk IO).
Best,
Norbert
On Mon, Sep 12, 2005 at 08:00:24PM -0700, Linus Torvalds wrote:
>
>
> On Mon, 12 Sep 2005, Norbert Kiesel wrote:
> >
> > I append the lspci -vvv from both 2.6.12.5 and 2.6.13.1 The diff
> > between these two is:
>
> Can you do "lspci -vvx" instead (the numbers are actually meaningful:
> they say what the hardware has been told, while the symbolic info contains
> some stuff that lspci actually gathered through other means by querying
> the kernel).
>
> Also, "diff -U 50 working broken" is a really nice way to show not only
> the differences - it gives enough context that you can see all the
> relevant info from the diff, and you don't even need to show the two
> different versions separately (ie the diff itself ends up containing
> pretty much all relevant info).
>
> Finally - if you can try to pinpoint it somewhat more (eg "2.6.13-rc3 is
> ok, -rc4 is not"), that would be very helpful..
>
> Linus
>
[-- Attachment #2: diff-U50 --]
[-- Type: text/plain, Size: 11848 bytes --]
--- 2.6.12.5/lspci-vvx 2005-09-12 20:26:21.000000000 -0700
+++ 2.6.13.1/lspci-vvx 2005-09-12 20:29:05.000000000 -0700
@@ -1,62 +1,62 @@
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 02)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
- Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x1
+ Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-00: 06 11 05 03 06 00 10 a2 02 00 00 06 00 00 00 00
+00: 06 11 05 03 06 00 10 22 02 00 00 06 00 00 00 00
10: 08 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: e4000000-e5ffffff
Prefetchable memory behind bridge: d0000000-dfffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 05 83 07 00 30 22 00 00 04 06 00 00 01 00
10: 00 00 00 00 00 00 00 00 00 01 01 00 90 90 00 00
20: 00 e4 f0 e5 00 d0 f0 df 00 00 00 00 00 00 00 00
30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 0c 00
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00: 06 11 86 06 87 00 10 02 22 00 01 06 00 00 80 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 06 11 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at a000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 71 05 07 00 90 02 10 8a 01 01 00 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a0 00 00 00 00 00 00 00 00 00 00 06 11 71 05
30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 00 00
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
@@ -74,127 +74,130 @@
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 12
Region 4: I/O ports at a800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 38 30 07 00 10 02 10 00 03 0c 08 20 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 01 a8 00 00 00 00 00 00 00 00 00 00 25 09 34 12
30: 00 00 00 00 80 00 00 00 00 00 00 00 0c 04 00 00
0000:00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 9
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 06 11 57 30 00 00 90 02 30 00 80 06 00 00 00 00
10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 68 00 00 00 00 00 00 00 00 00 00 00
0000:00:0a.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX (rev 10)
Subsystem: Accton Technology Corporation EN-1207D Fast Ethernet Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at ac00 [size=256]
Region 1: Memory at e7001000 (32-bit, non-prefetchable) [size=256]
Capabilities: [50] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 13 11 11 12 07 00 90 02 10 00 00 02 00 20 00 00
10: 01 ac 00 00 00 10 00 e7 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 13 11 11 12
30: 00 00 00 00 50 00 00 00 00 00 00 00 0b 01 20 40
0000:00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b000 [size=128]
Region 1: Memory at e7000000 (32-bit, non-prefetchable) [size=128]
+ Expansion ROM at 40080000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: b7 10 55 90 07 00 10 02 30 00 00 02 08 20 00 00
10: 01 b0 00 00 00 00 00 e7 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 b7 10 55 90
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0a 01 0a 0a
0000:00:0f.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: C-Media Electronics Inc CMI8738/C3DX PCI Audio Device
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at b400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: f6 13 11 01 05 00 10 02 10 00 01 04 00 20 00 00
10: 01 b4 00 00 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 f6 13 11 01
30: 00 00 00 00 c0 00 00 00 00 00 00 00 0a 01 02 18
0000:00:10.0 RAID bus controller: Silicon Image, Inc. SiI 0649 Ultra ATA/100 PCI to ATA Host Controller (rev 01)
Subsystem: Silicon Image, Inc. SiI 0649 Ultra ATA/100 PCI to ATA Host Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max)
Interrupt: pin A routed to IRQ 12
Region 0: I/O ports at b800 [size=8]
Region 1: I/O ports at bc00 [size=4]
Region 2: I/O ports at c000 [size=8]
Region 3: I/O ports at c400 [size=4]
Region 4: I/O ports at c800 [size=16]
+ Expansion ROM at 40000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=3 PME-
00: 95 10 49 06 07 00 90 02 01 00 04 01 00 40 00 00
10: 01 b8 00 00 01 bc 00 00 01 c0 00 00 01 c4 00 00
20: 01 c8 00 00 00 00 00 00 00 00 00 00 95 10 49 06
-30: 00 00 00 00 60 00 00 00 00 00 00 00 0c 01 02 04
+30: 01 00 00 00 60 00 00 00 00 00 00 00 0c 01 02 04
0000:01:00.0 VGA compatible controller: ATI Technologies Inc RV280 [Radeon 9200 PRO] (rev 01) (prog-if 00 [VGA])
Subsystem: Hightech Information System Ltd.: Unknown device 5960
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at e5000000 (32-bit, non-prefetchable) [size=64K]
+ Expansion ROM at e4000000 [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=80 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
- Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64- 64bit- FW- Rate=x1
+ Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 60 59 07 00 b0 02 01 00 00 03 08 20 80 00
10: 08 00 00 d0 01 90 00 00 00 00 00 e5 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 87 17 60 59
30: 00 00 00 00 58 00 00 00 00 00 00 00 05 01 08 00
0000:01:00.1 Display controller: ATI Technologies Inc: Unknown device 5940 (rev 01)
Subsystem: Hightech Information System Ltd.: Unknown device 5961
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min), Cache Line Size: 0x08 (32 bytes)
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e5010000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 02 10 40 59 07 00 b0 02 01 00 80 03 08 20 00 00
10: 08 00 00 d8 00 00 01 e5 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 87 17 61 59
30: 00 00 00 00 50 00 00 00 00 00 00 00 ff 00 08 00
next prev parent reply other threads:[~2005-09-13 3:38 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-09-12 23:59 2.6.13.1 locks machine after some time, 2.6.12.5 work fine Norbert Kiesel
2005-09-13 3:00 ` Linus Torvalds
2005-09-13 3:38 ` Norbert Kiesel [this message]
2005-09-13 14:25 ` Linus Torvalds
2005-09-13 14:57 ` Linus Torvalds
2005-09-13 16:02 ` Adam Kropelin
2005-09-13 15:55 ` Linus Torvalds
2005-09-13 20:22 ` David S. Miller
2005-09-13 22:25 ` Adam Kropelin
2005-09-13 22:43 ` [PATCH] ibmphp: Use dword accessors for PCI_ROM_ADDRESS Adam Kropelin
2005-09-13 23:11 ` Adam Kropelin
2005-09-13 23:15 ` [PATCH] pciehp: " Adam Kropelin
2005-09-13 23:17 ` [PATCH] shpchp: " Adam Kropelin
2005-09-13 23:20 ` [PATCH] qla2xxx: " Adam Kropelin
2005-09-13 16:27 ` 2.6.13.1 locks machine after some time, 2.6.12.5 work fine Norbert Kiesel
2005-09-13 17:09 ` Norbert Kiesel
2005-09-13 17:23 ` Linus Torvalds
2005-09-13 21:23 ` Norbert Kiesel
2005-09-13 22:24 ` Chris Wright
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050913033814.GA879@tbdnetworks.com \
--to=nkiesel@tbdnetworks.com \
--cc=linux-kernel@vger.kernel.org \
--cc=torvalds@osdl.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.