From: Dipankar Sarma <dipankar@in.ibm.com>
To: linux-scsi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Subject: [2.6.14-rc1] sym scsi boot hang
Date: Tue, 13 Sep 2005 18:18:04 +0530 [thread overview]
Message-ID: <20050913124804.GA5008@in.ibm.com> (raw)
My ppc64 box refuses to boot with 2.6.14-rc1. The console log
is included below. I see a lot of repeat of the last message
in the log and then the box hangs.
Any idea what might have caused this ?
Thanks
Dipankar
sym0: <1010-66> rev 0x1 at pci 0001:01:01.0 irq 115
sym0: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym0: SCSI BUS has been reset.
scsi0 : sym-2.2.1
target0:0:8: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
Vendor: IBM Model: IC35L036UCDY10-0 Rev: S25M
Type: Direct-Access ANSI SCSI revision: 03
target0:0:8: tagged command queuing enabled, command queue depth 16.
target0:0:8: Beginning Domain Validation
target0:0:8: asynchronous.
target0:0:8: wide asynchronous.
target0:0:8: FAST-80 WIDE SCSI 160.0 MB/s DT IU QAS (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:8: Write Buffer failure 700ff
target0:0:8: Domain Validation Disabing Information Units
target0:0:8: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:8: Write Buffer failure 700ff
target0:0:8: Domain Validation detected failure, dropping back
target0:0:8: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:8: Ending Domain Validation
target0:0:9: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
Vendor: IBM Model: IC35L036UCDY10-0 Rev: S25M
Type: Direct-Access ANSI SCSI revision: 03
target0:0:9: tagged command queuing enabled, command queue depth 16.
target0:0:9: Beginning Domain Validation
target0:0:9: asynchronous.
target0:0:9: wide asynchronous.
target0:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT IU QAS (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:9: Write Buffer failure 700ff
target0:0:9: Domain Validation Disabing Information Units
target0:0:9: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:9: Write Buffer failure 700ff
target0:0:9: Domain Validation detected failure, dropping back
target0:0:9: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:9: Ending Domain Validation
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s ST (25 ns, offset 31)
Vendor: IBM Model: IC35L036UCDY10-0 Rev: S25M
Type: Direct-Access ANSI SCSI revision: 03
target0:0:10: tagged command queuing enabled, command queue depth 16.
target0:0:10: Beginning Domain Validation
target0:0:10: asynchronous.
target0:0:10: wide asynchronous.
target0:0:10: Domain Validation skipping write tests
target0:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT IU QAS (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:10: Domain Validation Disabing Information Units
target0:0:10: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
sym0: unexpected disconnect
target0:0:10: Domain Validation detected failure, dropping back
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: Ending Domain Validation
Vendor: IBM Model: HSBPM2 PU2SCSI Rev: 0016
Type: Enclosure ANSI SCSI revision: 02
target0:0:14: Beginning Domain Validation
0:0:14:0: phase change 6-7 9@100503a8 resid=7.
0:0:14:0: phase change 6-7 9@100503a8 resid=7.
0:0:14:0: phase change 6-7 9@100503a8 resid=7.
0:0:14:0: phase change 6-7 9@100503a8 resid=7.
target0:0:14: Ending Domain Validation
Vendor: IBM Model: HSBPD4M PU3SCSI Rev: 0016
Type: Enclosure ANSI SCSI revision: 02
target0:0:15: Beginning Domain Validation
0:0:15:0: phase change 6-7 9@100503a8 resid=7.
0:0:15:0: phase change 6-7 9@100503a8 resid=7.
0:0:15:0: phase change 6-7 9@100503a8 resid=7.
0:0:15:0: phase change 6-7 9@100503a8 resid=7.
target0:0:15: Ending Domain Validation
sym1: <1010-66> rev 0x1 at pci 0001:01:01.1 irq 116
sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym1: SCSI BUS has been reset.
scsi1 : sym-2.2.1
sym2: <1010-66> rev 0x1 at pci 0001:41:01.0 irq 119
sym2: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym2: SCSI BUS has been reset.
scsi2 : sym-2.2.1
sym3: <1010-66> rev 0x1 at pci 0001:41:01.1 irq 120
sym3: No NVRAM, ID 7, Fast-80, LVD, parity checking
sym3: SCSI BUS has been reset.
scsi3 : sym-2.2.1
st: Version 20050830, fixed bufsize 32768, s/g segs 256
SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sda: drive cache: write through
SCSI device sda: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sda: drive cache: write through
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
Attached scsi disk sda at scsi0, channel 0, id 8, lun 0
SCSI device sdb: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sdb: drive cache: write through
SCSI device sdb: 71096640 512-byte hdwr sectors (36401 MB)
SCSI device sdb: drive cache: write through
sdb: sdb1 sdb2
Attached scsi disk sdb at scsi0, channel 0, id 9, lun 0
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
sdc: Spinning up disk....<6> target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
target0:0:10: FAST-40 WIDE SCSI 80.0 MB/s DT (25 ns, offset 31)
next reply other threads:[~2005-09-13 12:48 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-09-13 12:48 Dipankar Sarma [this message]
2005-09-13 13:17 ` [2.6.14-rc1] sym scsi boot hang Anton Blanchard
2005-09-13 14:29 ` Anton Blanchard
2005-09-13 16:35 ` James Bottomley
2005-09-13 16:47 ` Anton Blanchard
2005-09-13 17:32 ` James Bottomley
2005-09-13 17:13 ` Anton Blanchard
2005-09-13 17:33 ` Dipankar Sarma
2005-09-14 8:06 ` Anton Blanchard
2005-09-14 15:49 ` Alan Stern
2005-09-14 16:52 ` Mike Christie
2005-09-14 16:53 ` Mike Christie
2005-09-14 20:35 ` James Bottomley
2005-09-14 16:57 ` James Bottomley
2005-09-14 20:19 ` Alan Stern
2005-09-14 20:44 ` James Bottomley
2005-09-14 21:33 ` Alan Stern
2005-09-15 13:56 ` James Bottomley
2005-09-15 14:13 ` Alan Stern
2005-09-15 17:52 ` Alan Stern
2005-09-16 10:28 ` Anton Blanchard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20050913124804.GA5008@in.ibm.com \
--to=dipankar@in.ibm.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.