From: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
To: Florian Schirmer <jolt@tuxbox.org>, Dan Malek <dan@embeddededge.com>
Cc: obi@saftware.de, carjay@gmx.de,
linux-ppc-embedded <linuxppc-embedded@ozlabs.org>
Subject: Re: [PATCH] m8xx_wdt: software watchdog reset/interrupt select
Date: Fri, 18 Nov 2005 13:36:57 -0200 [thread overview]
Message-ID: <20051118153657.GA13943@logos.cnet> (raw)
In-Reply-To: <437C499C.6090002@tuxbox.org>
On Thu, Nov 17, 2005 at 10:13:00AM +0100, Florian Schirmer wrote:
> Hi,
>
> okay here is what the current driver does:
>
> During startup it installs a timer irq (PIT) handler and sets the
> frequency to half of the watchdog timeout. As soon as this timer irq
> triggers we reset the watchdog inside the irq handler.
>
> If a userspace handler takes over the watchdog we deinstall the timer
> irq handler and let the userspace daemon handle the watchdog resets.
>
> Please not that we're talking about the timer irq, not the watchdog
> interrupt.
>
> I don't see why it should make a difference wether the watchdog
> generates a IRQ0/HRESET or a system reset directly since it should never
> trigger anyway.
>
> All the patch does is to use a kernel timer instead of the hardware
> timer. So i'm little confused.
Florian,
After your message I decided to check if the PIT is working, guess what: it isnt.
Our board uses an external RTC (the internal RTC/PIT HW seem to be
nonexistant/nonfunctional).
I've changed the m8xx_wdt code to deal with that situation by checking
the RTC enable bit of RTCSC as follows:
m8xx_has_internal_rtc = in_be16(&imap->im_sit.sit_rtcsc) & RTCSC_RTE;
Problem with it is that the kernel sets the RTCSC_RTE bit
unconditionally in m8xx_calibrate_decr(), so you can't really know its
original value. The following patch changes m8xx_calibrate_decr()'s
RTC initialization to a weak function which can be overriden by board
specific code.
Dan, can you think of any nicer to avoid m8xx_calibrate_decr() from
overwriting RTCSC?
diff --git a/arch/ppc/syslib/m8xx_setup.c b/arch/ppc/syslib/m8xx_setup.c
index 1cc3abe..688616d 100644
--- a/arch/ppc/syslib/m8xx_setup.c
+++ b/arch/ppc/syslib/m8xx_setup.c
@@ -135,6 +135,16 @@ static struct irqaction tbint_irqaction
.name = "tbint",
};
+/* per-board overridable init_internal_rtc() function. */
+void __init __attribute__ ((weak))
+init_internal_rtc(void)
+{
+ /* Disable the RTC one second and alarm interrupts. */
+ out_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc, in_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc) & ~(RTCSC_SIE | RTCSC_ALE));
+ /* Enable the RTC */
+ out_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc, in_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc) | (RTCSC_RTF | RTCSC_RTE));
+}
+
/* The decrementer counts at the system (internal) clock frequency divided by
* sixteen, or external oscillator divided by four. We force the processor
* to use system clock divided by sixteen.
@@ -183,10 +193,7 @@ void __init m8xx_calibrate_decr(void)
out_be32(&((immap_t *)IMAP_ADDR)->im_sitk.sitk_rtcsck, KAPWR_KEY);
out_be32(&((immap_t *)IMAP_ADDR)->im_sitk.sitk_tbk, KAPWR_KEY);
- /* Disable the RTC one second and alarm interrupts. */
- out_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc, in_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc) & ~(RTCSC_SIE | RTCSC_ALE));
- /* Enable the RTC */
- out_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc, in_be16(&((immap_t *)IMAP_ADDR)->im_sit.sit_rtcsc) | (RTCSC_RTF | RTCSC_RTE));
+ init_internal_rtc();
/* Enabling the decrementer also enables the timebase interrupts
* (or from the other point of view, to get decrementer interrupts
diff --git a/arch/ppc/syslib/m8xx_wdt.c b/arch/ppc/syslib/m8xx_wdt.c
index a21632d..df6c955 100644
--- a/arch/ppc/syslib/m8xx_wdt.c
+++ b/arch/ppc/syslib/m8xx_wdt.c
@@ -19,6 +19,7 @@
#include <syslib/m8xx_wdt.h>
static int wdt_timeout;
+int m8xx_has_internal_rtc = 0;
static irqreturn_t m8xx_wdt_interrupt(int, void *, struct pt_regs *);
static struct irqaction m8xx_wdt_irqaction = {
@@ -45,35 +46,15 @@ static irqreturn_t m8xx_wdt_interrupt(in
return IRQ_HANDLED;
}
-void __init m8xx_wdt_handler_install(bd_t * binfo)
+#define SYPCR_SWP 0x1
+#define SYPCR_SWE 0x4
+
+
+void __init m8xx_wdt_install_irq(volatile immap_t *imap, bd_t *binfo)
{
- volatile immap_t *imap = (volatile immap_t *)IMAP_ADDR;
u32 pitc;
- u32 sypcr;
u32 pitrtclk;
- sypcr = in_be32(&imap->im_siu_conf.sc_sypcr);
-
- if (!(sypcr & 0x04)) {
- printk(KERN_NOTICE "m8xx_wdt: wdt disabled (SYPCR: 0x%08X)\n",
- sypcr);
- return;
- }
-
- m8xx_wdt_reset();
-
- printk(KERN_NOTICE
- "m8xx_wdt: active wdt found (SWTC: 0x%04X, SWP: 0x%01X)\n",
- (sypcr >> 16), sypcr & 0x01);
-
- wdt_timeout = (sypcr >> 16) & 0xFFFF;
-
- if (!wdt_timeout)
- wdt_timeout = 0xFFFF;
-
- if (sypcr & 0x01)
- wdt_timeout *= 2048;
-
/*
* Fire trigger if half of the wdt ticked down
*/
@@ -98,6 +79,67 @@ void __init m8xx_wdt_handler_install(bd_
printk(KERN_NOTICE
"m8xx_wdt: keep-alive trigger installed (PITC: 0x%04X)\n", pitc);
+}
+
+static void m8xx_wdt_timer_func(unsigned long data);
+
+static struct timer_list m8xx_wdt_timer =
+ TIMER_INITIALIZER(m8xx_wdt_timer_func, 0, 0);
+
+void m8xx_wdt_stop_timer(void)
+{
+ del_timer(&m8xx_wdt_timer);
+}
+
+void m8xx_wdt_install_timer(void)
+{
+ m8xx_wdt_timer.expires = jiffies + (HZ/2);
+ add_timer(&m8xx_wdt_timer);
+}
+
+static void m8xx_wdt_timer_func(unsigned long data)
+{
+ m8xx_wdt_reset();
+ m8xx_wdt_install_timer();
+}
+
+void __init m8xx_wdt_handler_install(bd_t * binfo)
+{
+ volatile immap_t *imap = (volatile immap_t *)IMAP_ADDR;
+ u32 sypcr;
+
+ sypcr = in_be32(&imap->im_siu_conf.sc_sypcr);
+
+ if (!(sypcr & SYPCR_SWE)) {
+ printk(KERN_NOTICE "m8xx_wdt: wdt disabled (SYPCR: 0x%08X)\n",
+ sypcr);
+ return;
+ }
+
+ m8xx_wdt_reset();
+
+ printk(KERN_NOTICE
+ "m8xx_wdt: active wdt found (SWTC: 0x%04X, SWP: 0x%01X)\n",
+ (sypcr >> 16), sypcr & SYPCR_SWP);
+
+ wdt_timeout = (sypcr >> 16) & 0xFFFF;
+
+ if (!wdt_timeout)
+ wdt_timeout = 0xFFFF;
+
+ if (sypcr & SYPCR_SWP)
+ wdt_timeout *= 2048;
+
+ m8xx_has_internal_rtc = in_be16(&imap->im_sit.sit_rtcsc) & RTCSC_RTE;
+
+ /* if the internal RTC is off use a kernel timer */
+ if (!m8xx_has_internal_rtc) {
+ if (wdt_timeout < (binfo->bi_intfreq/HZ))
+ printk(KERN_ERR "m8xx_wdt: timeout too short for ktimer!\n");
+ m8xx_wdt_install_timer();
+ } else
+ m8xx_wdt_install_irq(imap, binfo);
+
wdt_timeout /= binfo->bi_intfreq;
}
diff --git a/arch/ppc/syslib/m8xx_wdt.h b/arch/ppc/syslib/m8xx_wdt.h
index 0d81a9f..e75835f 100644
--- a/arch/ppc/syslib/m8xx_wdt.h
+++ b/arch/ppc/syslib/m8xx_wdt.h
@@ -9,8 +9,12 @@
#ifndef _PPC_SYSLIB_M8XX_WDT_H
#define _PPC_SYSLIB_M8XX_WDT_H
+extern int m8xx_has_internal_rtc;
+
extern void m8xx_wdt_handler_install(bd_t * binfo);
extern int m8xx_wdt_get_timeout(void);
extern void m8xx_wdt_reset(void);
+extern void m8xx_wdt_install_timer(void);
+extern void m8xx_wdt_stop_timer(void);
#endif /* _PPC_SYSLIB_M8XX_WDT_H */
diff --git a/drivers/char/watchdog/mpc8xx_wdt.c b/drivers/char/watchdog/mpc8xx_wdt.c
index 56d62ba..ac6fbac 100644
--- a/drivers/char/watchdog/mpc8xx_wdt.c
+++ b/drivers/char/watchdog/mpc8xx_wdt.c
@@ -27,7 +27,10 @@ static void mpc8xx_wdt_handler_disable(v
{
volatile immap_t *imap = (volatile immap_t *)IMAP_ADDR;
- imap->im_sit.sit_piscr &= ~(PISCR_PIE | PISCR_PTE);
+ if (!m8xx_has_internal_rtc)
+ m8xx_wdt_stop_timer();
+ else
+ out_be32(imap->im_sit.sit_piscr, in_be32(&imap->im_sit.sit_piscr) & ~(PISCR_PIE | PISCR_PTE));
printk(KERN_NOTICE "mpc8xx_wdt: keep-alive handler deactivated\n");
}
@@ -36,7 +39,10 @@ static void mpc8xx_wdt_handler_enable(vo
{
volatile immap_t *imap = (volatile immap_t *)IMAP_ADDR;
- imap->im_sit.sit_piscr |= PISCR_PIE | PISCR_PTE;
+ if (!m8xx_has_internal_rtc)
+ m8xx_wdt_install_timer();
+ else
+ out_be32(&imap->im_sit.sit_piscr, in_be32(&imap->im_sit.sit_piscr) | PISCR_PIE | PISCR_PTE);
printk(KERN_NOTICE "mpc8xx_wdt: keep-alive handler activated\n");
}
@@ -68,9 +74,6 @@ static int mpc8xx_wdt_release(struct ino
static ssize_t mpc8xx_wdt_write(struct file *file, const char *data, size_t len,
loff_t * ppos)
{
- if (ppos != &file->f_pos)
- return -ESPIPE;
-
if (len)
m8xx_wdt_reset();
next prev parent reply other threads:[~2005-11-18 20:56 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-11-14 14:38 [PATCH] m8xx_wdt: software watchdog reset/interrupt select Marcelo Tosatti
2005-11-14 20:55 ` Kumar Gala
2005-11-14 15:57 ` [PATCH] m8xx_wdt: software watchdog reset/interrupt select\ Marcelo Tosatti
2005-11-14 16:03 ` Marcelo Tosatti
2005-11-14 21:14 ` Kumar Gala
2005-11-15 6:11 ` Florian Schirmer
2005-11-15 6:41 ` [PATCH] m8xx_wdt: software watchdog reset/interrupt select Florian Schirmer
2005-11-15 5:42 ` Marcelo Tosatti
2005-11-15 14:21 ` Marcelo Tosatti
2005-11-16 11:47 ` Florian Schirmer
2005-11-16 8:36 ` Marcelo Tosatti
2005-11-17 9:13 ` Florian Schirmer
2005-11-18 15:36 ` Marcelo Tosatti [this message]
2005-11-19 6:16 ` Florian Schirmer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20051118153657.GA13943@logos.cnet \
--to=marcelo.tosatti@cyclades.com \
--cc=carjay@gmx.de \
--cc=dan@embeddededge.com \
--cc=jolt@tuxbox.org \
--cc=linuxppc-embedded@ozlabs.org \
--cc=obi@saftware.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.