From: "art" <art@usfltd.com>
To: <linux-kernel@vger.kernel.org>
Cc: <greg@kroah.com>
Subject: RE: SMART over USB - problem
Date: Fri, 2 Dec 2005 19:18:01 -0600 [thread overview]
Message-ID: <200512021918.AA134021646@usfltd.com> (raw)
SMART over USB - problem
usb--------------------------------------------------------
# smartctl -a -T verypermissive /dev/sde
smartctl version 5.33 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: WDC WD25 00JB-00GVA0 Version: 08.0
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
>> Terminate command early due to bad response to IEC mode page
Error Counter logging not supported
Error Events logging not supported
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
Device does not support Self Test logging
# smartctl -a -T verypermissive /dev/sdd
smartctl version 5.33 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: WDC WD30 00JB-00KFA0 Version: 08.0
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
>> Terminate command early due to bad response to IEC mode page
Error Counter logging not supported
Error Events logging not supported
scsiModePageOffset: response length too short, resp_len=4 offset=4 bd_len=0
Device does not support Self Test logging
ide----------------------------------------------------------
# smartctl -a -T verypermissive /dev/hda
smartctl version 5.33 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD1200BB-22CAA0
Serial Number: WD-WMA8Cxxxxxxx
Firmware Version: 16.06V16
User Capacity: 120,034,123,776 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 5
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Thu Dec 1 14:17:57 2005 CST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (4680) seconds.
Offline data collection
capabilities: (0x3b) SMART execute Offline immediate.
Auto Offline data collection on/off supp ort.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
No Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 87) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_ FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 099 091 021 Pre-fail Always - 5841
4 Start_Stop_Count 0x0032 100 100 040 Old_age Always - 708
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 086 086 000 Old_age Always - 10517
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 686
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
Device does not support Selective Self Tests/Logging
#
-----------------------------------------------------------------------
ide---works
usb---not
(USB-external-case) or (eide-usb-scsi conversion) ???
xboom
--------------------------------------------------------------------------------------
On Fri, Dec 02, 2005 at 05:28:42PM -0600, art wrote:
> > SMART over USB - problem
Do you expect it to work? USB storage is really scsi, so I doubt this
will ever work like you are expecting it to.
sorry,
greg k-h
SCSI-----------------------------------------------------------------------------------
# smartctl -a /dev/sdb
smartctl version 5.33 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Device: COMPAQ BF14688286 Version: HPB3
Serial number: 3KN04A1X0000xxxxxxxx
Device type: disk
Transport protocol: Parallel SCSI (SPI-4)
Local Time is: Fri Dec 2 19:00:19 2005 CST
Device supports SMART and is Enabled
Temperature Warning Enabled
SMART Health Status: OK
Current Drive Temperature: 38 C
Drive Trip Temperature: 68 C
Vendor (Seagate) cache information
Blocks sent to initiator = 1682981317
Blocks received from initiator = 330361456
Blocks read from cache and sent to initiator = 84738089
Number of read and write commands whose size <= segment size = 374742809
Number of read and write commands whose size > segment size = 120394
Error counter log:
Errors Corrected by Total Correction Gigabytes Total
EEC rereads/ errors algorithm processed uncorrected
fast | delayed rewrites corrected invocations [10^9 bytes] errors
read: 0 0 0 0 0 0.000 0
write: 0 0 0 0 0 0.000 0
Non-medium error count: 0
Error Events logging not supported
SMART Self-test log
Num Test Status segment LifeTime LBA_first_err [SK ASC ASQ]
Description number (hours)
# 1 Background long Interrupted ('-X' switch) - 354 - [- - -]
# 2 Background long Interrupted ('-X' switch) - 354 - [- - -]
# 3 Background long Interrupted ('-X' switch) - 354 - [- - -]
# 4 Background long Interrupted ('-X' switch) - 313 - [- - -]
# 5 Background long Interrupted ('-X' switch) - 313 - [- - -]
# 6 Background long Interrupted ('-X' switch) - 313 - [- - -]
# 7 Background short Completed - 0 - [- - -]
Long (extended) Self Test duration: 2102 seconds [35.0 minutes]
#
greg
works on SCSI/IDE why not on IDE over USB/IEEE1394/iSCSI/SAN... ???
is the problem in my external usb box or in linux usb/scsi stack ???
xboom
next reply other threads:[~2005-12-03 1:17 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-12-03 1:18 art [this message]
[not found] <mailman.1133566262.17183.linux-kernel2news@redhat.com>
2005-12-05 5:06 ` SMART over USB - problem Pete Zaitcev
[not found] <5fuei-2bW-3@gated-at.bofh.it>
2005-12-03 2:43 ` Robert Hancock
-- strict thread matches above, loose matches on Subject: below --
2005-12-02 23:28 art
2005-12-03 0:19 ` Greg KH
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200512021918.AA134021646@usfltd.com \
--to=art@usfltd.com \
--cc=greg@kroah.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.