From: Jon Mason <jdmason@us.ibm.com>
To: Muli Ben-Yehuda <mulix@mulix.org>
Cc: Linux-Kernel <linux-kernel@vger.kernel.org>,
muli@il.ibm.com, jgarzik@pobox.com
Subject: Re: 2.6.15-rc5-mm2 does not boot on AMD64 with sata_sil
Date: Wed, 14 Dec 2005 17:37:05 -0600 [thread overview]
Message-ID: <20051214233705.GA22464@us.ibm.com> (raw)
In-Reply-To: <20051213103156.GD23695@granada.merseine.nu>
I regressed only the sata_sil driver changes in the git-libata-all.patch,
and my system now find the SATA disks. While not the final solution,
it's a quick fix.
Jeff, I'll be happy to test any fixes or debug drivers.
Thanks,
Jon
On Tue, Dec 13, 2005 at 12:31:56PM +0200, Muli Ben-Yehuda wrote:
> My dual AMD64 no longer boots with 2.6.15-rc5-mm2 because it can't
> find its disks. 2.6.15-rc5-gitX works fine. Boot logs and lscpi
> attached.
>
> Interesting parts of the diff between vanillalog and mmlog (trying
> pci=routeirq and pci=noacpi didn't help):
>
> @@ -84,6 +87,11 @@
> usbcore: registered new driver hub
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
> +PCI: Cannot allocate resource region 0 of device 0000:01:02.0
> +PCI: Cannot allocate resource region 1 of device 0000:01:02.0
> +PCI: Cannot allocate resource region 2 of device 0000:01:02.0
> +PCI: Cannot allocate resource region 3 of device 0000:01:02.0
> +PCI: Cannot allocate resource region 4 of device 0000:01:02.0
> agpgart: Detected AMD 8151 AGP Bridge rev B3
> agpgart: AGP aperture is 256M @ 0xe0000000
> PCI-DMA: Disabling IOMMU.
> @@ -164,28 +175,21 @@
> Uniform CD-ROM driver Revision: 3.20
> GSI 17 sharing vector 0xB1 and IRQ 17
> ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 17 (level, low) -> IRQ 177
> -ata1: SATA max UDMA/100 cmd 0xFFFFC20000006080 ctl 0xFFFFC2000000608A bmdma 0x7ata2: SATA max UDMA/100 cmd 0xFFFFC200000060C0 ctl 0xFFFFC200000060CA bmdma 0x7ata1: no device found (phy stat 00000000)
> +ata1: SATA max UDMA/100 cmd 0xFFFFC20000006080 ctl 0xFFFFC2000000608A bmdma 0x7ata2: SATA max UDMA/100 cmd 0xFFFFC200000060C0 ctl 0xFFFFC200000060CA bmdma 0x7ata1: SATA link down (SStatus 0)
> scsi0 : sata_sil
> -ata2: dev 0 ATA-7, max UDMA/133, 156312576 sectors: LBA
> -ata2: dev 0 configured for UDMA/100
> +ata2: SATA link up 1.5 Gbps (SStatus 113)
> +ata2: dev 0 not supported, ignoring
> scsi1 : sata_sil
> - Vendor: ATA Model: Maxtor 6Y080M0 Rev: YAR5
> - Type: Direct-Access ANSI SCSI revision: 05
> -SCSI device sda: 156312576 512-byte hdwr sectors (80032 MB)
> -SCSI device sda: drive cache: write back
> -SCSI device sda: 156312576 512-byte hdwr sectors (80032 MB)
> -SCSI device sda: drive cache: write back
> - sda: sda1 sda2
> -sd 1:0:0:0: Attached scsi disk sda
> -Fusion MPT base driver 3.03.04
> +Fusion MPT base driver 3.03.05
> Copyright (c) 1999-2005 LSI Logic Corporation
> -Fusion MPT SPI Host driver 3.03.04
> +Fusion MPT SPI Host driver 3.03.05
> GSI 18 sharing vector 0xB9 and IRQ 18
> ACPI: PCI Interrupt 0000:01:03.2[C] -> GSI 16 (level, low) -> IRQ 185
> ehci_hcd 0000:01:03.2: EHCI Host Controller
> ehci_hcd 0000:01:03.2: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:01:03.2: irq 185, io mem 0xf9550000
> ehci_hcd 0000:01:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> +usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 5 ports detected
> GSI 19 sharing vector 0xC1 and IRQ 19
>
>
> Cheers,
> Muli
> --
> Muli Ben-Yehuda
> http://www.mulix.org | http://mulix.livejournal.com/
>
> ;; welcome, muli, to the one true editor!
> Bootdata ok (command line is root=/dev/sda2 selinux=0 console=ttyS1,19200n8)
> Linux version 2.6.15-rc5-mm2 (muli@rhun) (gcc version 3.4.1) #3 SMP Tue Dec 135BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
> BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 00000000dff60000 (usable)
> BIOS-e820: 00000000dff60000 - 00000000dff72000 (ACPI data)
> BIOS-e820: 00000000dff72000 - 00000000dff80000 (ACPI NVS)
> BIOS-e820: 00000000dff80000 - 00000000e0000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
> SRAT: PXM 0 -> APIC 0 -> Node 0
> SRAT: PXM 1 -> APIC 1 -> Node 1
> SRAT: Node 0 PXM 0 0-a0000
> SRAT: Node 0 PXM 0 0-e0000000
> Bootmem setup node 0 0000000000000000-00000000dff60000
> ACPI: PM-Timer IO Port: 0x8008
> ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
> Processor #0 15:5 APIC version 16
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
> Processor #1 15:5 APIC version 16
> ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
> ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
> ACPI: IOAPIC (id[0x03] address[0xf9220000] gsi_base[24])
> IOAPIC[1]: apic_id 3, version 17, address 0xf9220000, GSI 24-27
> ACPI: IOAPIC (id[0x04] address[0xf9230000] gsi_base[28])
> IOAPIC[2]: apic_id 4, version 17, address 0xf9230000, GSI 28-31
> ACPI: IOAPIC (id[0x05] address[0xf9200000] gsi_base[32])
> IOAPIC[3]: apic_id 5, version 17, address 0xf9200000, GSI 32-35
> ACPI: IOAPIC (id[0x06] address[0xf9210000] gsi_base[36])
> IOAPIC[4]: apic_id 6, version 17, address 0xf9210000, GSI 36-39
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
> Setting APIC routing to flat
> DMI present.
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at e2000000 (gap: e0000000:1ec00000)
> Checking aperture...
> CPU 0: aperture @ e0000000 size 256 MB
> CPU 1: aperture @ e0000000 size 256 MB
> Built 1 zonelists
> Initializing CPU#0
> Kernel command line: root=/dev/sda2 selinux=0 console=ttyS1,19200n8
> PID hash table entries: 4096 (order: 12, 131072 bytes)
> time.c: Using 3.579545 MHz PM timer.
> time.c: Detected 2393.242 MHz processor.
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
> Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
> Memory: 3606672k/3669376k available (3311k kernel code, 62308k reserved, 1441k)Calibrating delay using timer specific routine.. 4796.16 BogoMIPS (lpj=9592329)Mount-cache hash table entries: 256
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 1024K (64 bytes/line)
> CPU 0(1) -> Node 0 -> Core 0
> mtrr: v2.0 (20020519)
> Using local APIC timer interrupts.
> Detected 12.464 MHz APIC timer.
> Booting processor 1/2 APIC 0x1
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 4786.72 BogoMIPS (lpj=9573445)CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 1024K (64 bytes/line)
> CPU 1(1) -> Node 0 -> Core 0
> AMD Opteron(tm) Processor 250 stepping 0a
> CPU 1: Syncing TSC to CPU 0.
> CPU 1: synchronized TSC with CPU 0 (last diff -20 cycles, maxerr 1228 cycles)
> Brought up 2 CPUs
> Disabling vsyscall due to use of PM timer
> time.c: Using PM based timekeeping.
> testing NMI watchdog ... CPU#1: NMI appears to be stuck (19->19)!
> migration_cost=866
> NET: Registered protocol family 16
> ACPI: bus type pci registered
> PCI: Using configuration type 1
> ACPI: Subsystem revision 20050916
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *9
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 *10 11)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 10 *11)
> ACPI: PCI Root Bridge [PCI1] (0000:08)
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
> PCI: Cannot allocate resource region 0 of device 0000:01:02.0
> PCI: Cannot allocate resource region 1 of device 0000:01:02.0
> PCI: Cannot allocate resource region 2 of device 0000:01:02.0
> PCI: Cannot allocate resource region 3 of device 0000:01:02.0
> PCI: Cannot allocate resource region 4 of device 0000:01:02.0
> agpgart: Detected AMD 8151 AGP Bridge rev B3
> agpgart: AGP aperture is 256M @ 0xe0000000
> PCI-DMA: Disabling IOMMU.
> PCI: Bridge: 0000:00:06.0
> IO window: 2000-2fff
> MEM window: f9500000-f95fffff
> PREFETCH window: f9000000-f90fffff
> PCI: Bridge: 0000:00:0a.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:0b.0
> IO window: disabled.
> MEM window: f9600000-f96fffff
> PREFETCH window: disabled.
> PCI: Failed to allocate mem resource #6:20000@f8000000 for 0000:09:00.0
> PCI: Bridge: 0000:08:01.0
> IO window: disabled.
> MEM window: f8000000-f8ffffff
> PREFETCH window: f0000000-f7ffffff
> PCI: Bridge: 0000:08:03.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: disabled.
> PCI: Bridge: 0000:08:04.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: disabled.
> IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
> Total HugeTLB memory allocated, 0
> Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> io scheduler noop registered
> io scheduler deadline registered
> io scheduler cfq registered
> PCI: MSI quirk detected. pci_msi_quirk set.
> PCI: MSI quirk detected. pci_msi_quirk set.
> PCI: MSI quirk detected. pci_msi_quirk set.
> PCI: MSI quirk detected. pci_msi_quirk set.
> ACPI: Power Button (FF) [PWRF]
> ACPI: Sleep Button (FF) [SLPF]
> ACPI: Power Button (CM) [PWRB]
> Real Time Clock Driver v1.12
> hw_random: AMD768 system management I/O registers at 0x8000.
> hw_random hardware driver 1.0.0 loaded
> Linux agpgart interface v0.101 (c) Dave Jones
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> mice: PS/2 mouse device common for all mice
> FDC 0 is a National Semiconductor PC87306
> input: AT Translated Set 2 keyboard as /class/input/input0
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> loop: loaded (max 8 devices)
> Intel(R) PRO/1000 Network Driver - version 6.1.16-k2
> Copyright (c) 1999-2005 Intel Corporation.
> e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI
> e100: Copyright(c) 1999-2005 Intel Corporation
> tg3.c:v3.44 (Dec 6, 2005)
> GSI 16 sharing vector 0xA9 and IRQ 16
> ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 28 (level, low) -> IRQ 169
> eth0: Tigon3 [partno(none) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/100100:0d:60:53:1f:cf
> eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
> eth0: dma_rwctrl[769f4000]
> forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.47.
> tun: Universal TUN/TAP device driver, 1.6
> tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
> netconsole: not configured, aborting
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> AMD8111: IDE controller at PCI slot 0000:00:07.1
> AMD8111: chipset revision 3
> AMD8111: not 100% native mode: will probe irqs later
> AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller
> ide0: BM-DMA at 0x1460-0x1467, BIOS settings: hda:pio, hdb:pio
> ide1: BM-DMA at 0x1468-0x146f, BIOS settings: hdc:DMA, hdd:pio
> hdc: LITE-ON LTR-48327S, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> hdc: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> GSI 17 sharing vector 0xB1 and IRQ 17
> ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 17 (level, low) -> IRQ 177
> ata1: SATA max UDMA/100 cmd 0xFFFFC20000006080 ctl 0xFFFFC2000000608A bmdma 0x7ata2: SATA max UDMA/100 cmd 0xFFFFC200000060C0 ctl 0xFFFFC200000060CA bmdma 0x7ata1: SATA link down (SStatus 0)
> scsi0 : sata_sil
> ata2: SATA link up 1.5 Gbps (SStatus 113)
> ata2: dev 0 not supported, ignoring
> scsi1 : sata_sil
> Fusion MPT base driver 3.03.05
> Copyright (c) 1999-2005 LSI Logic Corporation
> Fusion MPT SPI Host driver 3.03.05
> GSI 18 sharing vector 0xB9 and IRQ 18
> ACPI: PCI Interrupt 0000:01:03.2[C] -> GSI 16 (level, low) -> IRQ 185
> ehci_hcd 0000:01:03.2: EHCI Host Controller
> ehci_hcd 0000:01:03.2: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:01:03.2: irq 185, io mem 0xf9550000
> ehci_hcd 0000:01:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 5 ports detected
> GSI 19 sharing vector 0xC1 and IRQ 19
> ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 18 (level, low) -> IRQ 193
> ohci_hcd 0000:01:03.0: OHCI Host Controller
> ohci_hcd 0000:01:03.0: new USB bus registered, assigned bus number 2
> ohci_hcd 0000:01:03.0: irq 193, io mem 0xf9530000
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 3 ports detected
> GSI 20 sharing vector 0xC9 and IRQ 20
> ACPI: PCI Interrupt 0000:01:03.1[B] -> GSI 19 (level, low) -> IRQ 201
> ohci_hcd 0000:01:03.1: OHCI Host Controller
> ohci_hcd 0000:01:03.1: new USB bus registered, assigned bus number 3
> ohci_hcd 0000:01:03.1: irq 201, io mem 0xf9540000
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> USB Universal Host Controller Interface driver v2.3
> usbcore: registered new driver usblp
> /home/muli/w/iommu/dma_ops/mm/drivers/usb/class/usblp.c: v0.13: USB Printer DerInitializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> /home/muli/w/iommu/dma_ops/mm/drivers/usb/input/hid-core.c: v2.6:USB HID core rdevice-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com
> Intel 810 + AC97 Audio, version 1.01, 11:43:14 Dec 13 2005
> ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 177
> i810: AMD-8111 IOHub found at IO 0x1400 and 0x1000, MEM 0x0000 and 0x0000, IRQ7i810_audio: Audio Controller supports 6 channels.
> i810_audio: Defaulting to base 2 channel mode.
> i810_audio: Resetting connection 0
> ac97_codec: AC97 codec, id: ALG96 (Unknown)
> i810_audio: only 48Khz playback available.
> i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not present),2oprofile: using NMI interrupt.
> NET: Registered protocol family 2
> IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
> TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
> TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
> TCP: Hash tables configured (established 262144 bind 65536)
> TCP reno registered
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 10
> IPv6 over IPv4 tunneling driver
> NET: Registered protocol family 17
> powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.60.0)
> powernow-k8: MP systems not supported by PSB BIOS structure
> powernow-k8: MP systems not supported by PSB BIOS structure
> Root-NFS: No NFS server available, giving up.
> VFS: Unable to mount root fs via NFS, trying floppy.
> VFS: Insert root floppy and press ENTER
> Bootdata ok (command line is root=/dev/sda2 selinux=0 console=ttyS1,19200n8)
> Linux version 2.6.15-rc5 (muli@rhun) (gcc version 3.4.1) #1 SMP Tue Dec 13 11:5BIOS-provided physical RAM map:
> BIOS-e820: 0000000000000000 - 000000000009dc00 (usable)
> BIOS-e820: 000000000009dc00 - 00000000000a0000 (reserved)
> BIOS-e820: 00000000000d0000 - 0000000000100000 (reserved)
> BIOS-e820: 0000000000100000 - 00000000dff60000 (usable)
> BIOS-e820: 00000000dff60000 - 00000000dff72000 (ACPI data)
> BIOS-e820: 00000000dff72000 - 00000000dff80000 (ACPI NVS)
> BIOS-e820: 00000000dff80000 - 00000000e0000000 (reserved)
> BIOS-e820: 00000000fec00000 - 00000000fec00400 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
> SRAT: PXM 0 -> APIC 0 -> Node 0
> SRAT: PXM 1 -> APIC 1 -> Node 1
> SRAT: Node 0 PXM 0 0-a0000
> SRAT: Node 0 PXM 0 0-e0000000
> Bootmem setup node 0 0000000000000000-00000000dff60000
> ACPI: PM-Timer IO Port: 0x8008
> ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
> Processor #0 15:5 APIC version 16
> ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
> Processor #1 15:5 APIC version 16
> ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
> ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
> ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
> IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23
> ACPI: IOAPIC (id[0x03] address[0xf9220000] gsi_base[24])
> IOAPIC[1]: apic_id 3, version 17, address 0xf9220000, GSI 24-27
> ACPI: IOAPIC (id[0x04] address[0xf9230000] gsi_base[28])
> IOAPIC[2]: apic_id 4, version 17, address 0xf9230000, GSI 28-31
> ACPI: IOAPIC (id[0x05] address[0xf9200000] gsi_base[32])
> IOAPIC[3]: apic_id 5, version 17, address 0xf9200000, GSI 32-35
> ACPI: IOAPIC (id[0x06] address[0xf9210000] gsi_base[36])
> IOAPIC[4]: apic_id 6, version 17, address 0xf9210000, GSI 36-39
> ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
> Setting APIC routing to flat
> Using ACPI (MADT) for SMP configuration information
> Allocating PCI resources starting at e2000000 (gap: e0000000:1ec00000)
> Checking aperture...
> CPU 0: aperture @ e0000000 size 256 MB
> CPU 1: aperture @ e0000000 size 256 MB
> Built 1 zonelists
> Kernel command line: root=/dev/sda2 selinux=0 console=ttyS1,19200n8
> Initializing CPU#0
> PID hash table entries: 4096 (order: 12, 131072 bytes)
> time.c: Using 3.579545 MHz PM timer.
> time.c: Detected 2393.249 MHz processor.
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
> Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
> Memory: 3606736k/3669376k available (3220k kernel code, 62244k reserved, 1400k)Calibrating delay using timer specific routine.. 4795.95 BogoMIPS (lpj=9591905)Mount-cache hash table entries: 256
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 1024K (64 bytes/line)
> CPU 0(1) -> Node 0 -> Core 0
> mtrr: v2.0 (20020519)
> Using local APIC timer interrupts.
> Detected 12.464 MHz APIC timer.
> Booting processor 1/2 APIC 0x1
> Initializing CPU#1
> Calibrating delay using timer specific routine.. 4786.72 BogoMIPS (lpj=9573444)CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
> CPU: L2 Cache: 1024K (64 bytes/line)
> CPU 1(1) -> Node 0 -> Core 0
> AMD Opteron(tm) Processor 250 stepping 0a
> CPU 1: Syncing TSC to CPU 0.
> CPU 1: synchronized TSC with CPU 0 (last diff -9 cycles, maxerr 1225 cycles)
> Brought up 2 CPUs
> Disabling vsyscall due to use of PM timer
> time.c: Using PM based timekeeping.
> testing NMI watchdog ... OK.
> NET: Registered protocol family 16
> ACPI: bus type pci registered
> PCI: Using configuration type 1
> ACPI: Subsystem revision 20050902
> ACPI: Interpreter enabled
> ACPI: Using IOAPIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 *5 10 11)
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 10 11) *9
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 *10 11)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 10 *11)
> ACPI: PCI Root Bridge [PCI1] (0000:08)
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
> agpgart: Detected AMD 8151 AGP Bridge rev B3
> agpgart: AGP aperture is 256M @ 0xe0000000
> PCI-DMA: Disabling IOMMU.
> PCI: Bridge: 0000:00:06.0
> IO window: 2000-2fff
> MEM window: f9500000-f95fffff
> PREFETCH window: f9000000-f90fffff
> PCI: Bridge: 0000:00:0a.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: disabled.
> PCI: Bridge: 0000:00:0b.0
> IO window: disabled.
> MEM window: f9600000-f96fffff
> PREFETCH window: disabled.
> PCI: Failed to allocate mem resource #6:20000@f8000000 for 0000:09:00.0
> PCI: Bridge: 0000:08:01.0
> IO window: disabled.
> MEM window: f8000000-f8ffffff
> PREFETCH window: f0000000-f7ffffff
> PCI: Bridge: 0000:08:03.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: disabled.
> PCI: Bridge: 0000:08:04.0
> IO window: disabled.
> MEM window: disabled.
> PREFETCH window: disabled.
> IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
> Total HugeTLB memory allocated, 0
> Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
> io scheduler noop registered
> io scheduler deadline registered
> io scheduler cfq registered
> PCI: MSI quirk detected. pci_msi_quirk set.
> PCI: MSI quirk detected. pci_msi_quirk set.
> PCI: MSI quirk detected. pci_msi_quirk set.
> PCI: MSI quirk detected. pci_msi_quirk set.
> ACPI: Power Button (FF) [PWRF]
> ACPI: Sleep Button (FF) [SLPF]
> ACPI: Power Button (CM) [PWRB]
> Real Time Clock Driver v1.12
> hw_random: AMD768 system management I/O registers at 0x8000.
> hw_random hardware driver 1.0.0 loaded
> Linux agpgart interface v0.101 (c) Dave Jones
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
> FDC 0 is a National Semiconductor PC87306
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
> loop: loaded (max 8 devices)
> Intel(R) PRO/1000 Network Driver - version 6.1.16-k2
> Copyright (c) 1999-2005 Intel Corporation.
> e100: Intel(R) PRO/100 Network Driver, 3.4.14-k4-NAPI
> e100: Copyright(c) 1999-2005 Intel Corporation
> tg3.c:v3.44 (Dec 6, 2005)
> GSI 16 sharing vector 0xA9 and IRQ 16
> ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 28 (level, low) -> IRQ 169
> eth0: Tigon3 [partno(none) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/100feth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
> eth0: dma_rwctrl[769f4000]
> forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.47.
> tun: Universal TUN/TAP device driver, 1.6
> tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
> netconsole: not configured, aborting
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> AMD8111: IDE controller at PCI slot 0000:00:07.1
> AMD8111: chipset revision 3
> AMD8111: not 100% native mode: will probe irqs later
> AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller
> ide0: BM-DMA at 0x1460-0x1467, BIOS settings: hda:pio, hdb:pio
> ide1: BM-DMA at 0x1468-0x146f, BIOS settings: hdc:DMA, hdd:pio
> hdc: LITE-ON LTR-48327S, ATAPI CD/DVD-ROM drive
> ide1 at 0x170-0x177,0x376 on irq 15
> hdc: ATAPI 48X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
> Uniform CD-ROM driver Revision: 3.20
> GSI 17 sharing vector 0xB1 and IRQ 17
> ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 17 (level, low) -> IRQ 177
> ata1: SATA max UDMA/100 cmd 0xFFFFC20000006080 ctl 0xFFFFC2000000608A bmdma 0x7ata2: SATA max UDMA/100 cmd 0xFFFFC200000060C0 ctl 0xFFFFC200000060CA bmdma 0x7ata1: no device found (phy stat 00000000)
> scsi0 : sata_sil
> ata2: dev 0 ATA-7, max UDMA/133, 156312576 sectors: LBA
> ata2: dev 0 configured for UDMA/100
> scsi1 : sata_sil
> Vendor: ATA Model: Maxtor 6Y080M0 Rev: YAR5
> Type: Direct-Access ANSI SCSI revision: 05
> SCSI device sda: 156312576 512-byte hdwr sectors (80032 MB)
> SCSI device sda: drive cache: write back
> SCSI device sda: 156312576 512-byte hdwr sectors (80032 MB)
> SCSI device sda: drive cache: write back
> sda: sda1 sda2
> sd 1:0:0:0: Attached scsi disk sda
> Fusion MPT base driver 3.03.04
> Copyright (c) 1999-2005 LSI Logic Corporation
> Fusion MPT SPI Host driver 3.03.04
> GSI 18 sharing vector 0xB9 and IRQ 18
> ACPI: PCI Interrupt 0000:01:03.2[C] -> GSI 16 (level, low) -> IRQ 185
> ehci_hcd 0000:01:03.2: EHCI Host Controller
> ehci_hcd 0000:01:03.2: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:01:03.2: irq 185, io mem 0xf9550000
> ehci_hcd 0000:01:03.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 5 ports detected
> GSI 19 sharing vector 0xC1 and IRQ 19
> ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 18 (level, low) -> IRQ 193
> ohci_hcd 0000:01:03.0: OHCI Host Controller
> ohci_hcd 0000:01:03.0: new USB bus registered, assigned bus number 2
> ohci_hcd 0000:01:03.0: irq 193, io mem 0xf9530000
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 3 ports detected
> GSI 20 sharing vector 0xC9 and IRQ 20
> ACPI: PCI Interrupt 0000:01:03.1[B] -> GSI 19 (level, low) -> IRQ 201
> ohci_hcd 0000:01:03.1: OHCI Host Controller
> ohci_hcd 0000:01:03.1: new USB bus registered, assigned bus number 3
> ohci_hcd 0000:01:03.1: irq 201, io mem 0xf9540000
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> USB Universal Host Controller Interface driver v2.3
> usbcore: registered new driver usblp
> /home/muli/kernel/hg/drivers/usb/class/usblp.c: v0.13: USB Printer Device ClasrInitializing USB Mass Storage driver...
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usbcore: registered new driver usbhid
> /home/muli/kernel/hg/drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> mice: PS/2 mouse device common for all mice
> device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
> input: AT Translated Set 2 keyboard as /class/input/input0
> Intel 810 + AC97 Audio, version 1.01, 11:24:59 Dec 13 2005
> ACPI: PCI Interrupt 0000:00:07.5[B] -> GSI 17 (level, low) -> IRQ 177
> i810: AMD-8111 IOHub found at IO 0x1400 and 0x1000, MEM 0x0000 and 0x0000, IRQ7input: PS/2 Generic Mouse as /class/input/input1
> i810_audio: Audio Controller supports 6 channels.
> i810_audio: Defaulting to base 2 channel mode.
> i810_audio: Resetting connection 0
> ac97_codec: AC97 codec, id: ALG96 (Unknown)
> i810_audio: only 48Khz playback available.
> i810_audio: AC'97 codec 0 Unable to map surround DAC's (or DAC's not present),2oprofile: using NMI interrupt.
> NET: Registered protocol family 2
> IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
> TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
> TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
> TCP: Hash tables configured (established 262144 bind 65536)
> TCP reno registered
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 10
> IPv6 over IPv4 tunneling driver
> NET: Registered protocol family 17
> powernow-k8: Found 2 AMD Athlon 64 / Opteron processors (version 1.50.4)
> powernow-k8: MP systems not supported by PSB BIOS structure
> powernow-k8: MP systems not supported by PSB BIOS structure
> ReiserFS: sda2: found reiserfs format "3.6" with standard journal
> 0000:00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=69
> I/O behind bridge: 00002000-00002fff
> Memory behind bridge: f9500000-f95fffff
> Prefetchable memory behind bridge: fff00000-000fffff
> BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [c0] #08 [0086]
> Capabilities: [f0] #08 [8000]
> 00: 22 10 60 74 17 00 30 02 07 00 04 06 00 40 01 00
> 10: 00 00 00 00 00 00 00 00 00 01 01 45 20 20 00 02
> 20: 50 f9 50 f9 f0 ff 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 c0 00 00 00 00 00 00 00 ff 00 06 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 04 06 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 14 10 b7 02 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 08 f0 86 00 20 00 00 00 d0 00 00 00 22 00 01 00
> d0: 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 0d 00 00 00 0d 00 00 00 18 00 00 00 00 00
> f0: 08 00 00 80 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
> Subsystem: IBM: Unknown device 02b7
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> 00: 22 10 68 74 0f 00 20 02 05 00 01 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 80 30 07 b1 01 00 00 82 2f 00 00 01 00 00 00 c0
> 50: 00 00 00 00 8d 71 00 00 4e 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 14 10 b7 02 01 81 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03) (prog-if 8a [Master SecP PriP])
> Subsystem: IBM: Unknown device 02b7
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Region 4: I/O ports at 1460 [size=16]
> 00: 22 10 69 74 05 00 00 02 03 8a 01 01 00 40 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 61 14 00 00 00 00 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 00 00
> 40: 43 f0 00 00 00 00 00 00 5e 20 5e 5e a2 00 20 ff
> 50: 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 14 10 b7 02 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02)
> Subsystem: IBM: Unknown device 02b7
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin D routed to IRQ 19
> Region 0: I/O ports at 1440 [size=32]
> 00: 22 10 6a 74 01 00 00 02 02 00 05 0c 00 40 00 00
> 10: 41 14 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 04 00 00
> 40: 02 00 05 0c 14 10 b7 02 06 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
> Subsystem: IBM: Unknown device 02b7
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 6b 74 00 00 80 02 05 00 80 06 00 40 00 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 80 b1 09 07 00 00 00 00 20 04 40 00 00 00 00 00
> 50: 01 81 00 00 0f 00 95 ba 01 80 00 00 00 00 00 00
> 60: 00 00 80 06 13 00 00 00 00 00 00 00 00 00 00 00
> 70: 06 29 4b d5 0c 00 00 00 00 00 00 00 14 10 b7 02
> 80: 00 00 00 00 01 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 fe 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: b3 31 5c 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:07.5 Multimedia audio controller: Advanced Micro Devices [AMD] AMD-8111 AC97 Audio (rev 03)
> Subsystem: IBM: Unknown device 02b7
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Interrupt: pin B routed to IRQ 17
> Region 0: I/O ports at 1000 [size=256]
> Region 1: I/O ports at 1400 [size=64]
> 00: 22 10 6d 74 05 00 00 02 03 00 01 04 00 40 00 00
> 10: 01 10 00 00 01 14 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 09 02 00 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
> BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [a0] Capabilities: [b8] #08 [8000]
> Capabilities: [c0] #08 [004a]
> 00: 22 10 50 74 17 01 30 02 12 00 04 06 00 40 81 00
> 10: 00 00 00 00 00 00 00 00 00 02 02 40 f1 01 20 02
> 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 a0 00 00 00 00 00 00 00 ff 00 07 00
> 40: 04 00 1f 00 01 00 00 00 02 0d 00 00 01 2c 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 07 b8 c3 00 50 00 03 00 0e 00 ff ff 02 00 ff ff
> b0: 00 00 00 00 00 00 00 00 08 c0 00 80 00 00 00 03
> c0: 08 00 4a 00 20 00 11 11 20 00 00 00 22 04 35 00
> d0: 02 00 35 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 11 00 00 00 12 00 00 00 14 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01) (prog-if 10 [IO-APIC])
> Subsystem: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f9220000 (64-bit, non-prefetchable) [size=4K]
> 00: 22 10 51 74 06 00 00 02 01 10 00 08 00 00 00 00
> 10: 04 00 22 f9 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 51 74
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 00 00 00 03 00 00 00 04 00 22 f9 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: f9600000-f96fffff
> Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
> BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [a0] Capabilities: [b8] #08 [8000]
> 00: 22 10 50 74 17 01 30 02 12 00 04 06 00 40 81 00
> 10: 00 00 00 00 00 00 00 00 00 03 03 40 f1 01 20 02
> 20: 60 f9 60 f9 f1 ff 01 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 a0 00 00 00 00 00 00 00 ff 00 07 00
> 40: 04 00 1f 00 01 00 00 00 00 00 00 00 01 2c 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 07 b8 83 00 58 00 03 00 0e 00 ff ff 02 00 ff ff
> b0: 00 00 00 00 00 00 00 00 08 00 00 80 00 00 00 04
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01) (prog-if 10 [IO-APIC])
> Subsystem: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f9230000 (64-bit, non-prefetchable) [size=4K]
> 00: 22 10 51 74 06 00 00 02 01 10 00 08 00 00 00 00
> 10: 04 00 23 f9 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 51 74
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 00 00 00 03 00 00 00 04 00 23 f9 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Capabilities: [80] #08 [2101]
> Capabilities: [a0] #08 [2101]
> Capabilities: [c0] #08 [2101]
> 00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
> 40: 01 01 05 00 04 04 01 00 01 01 01 00 01 01 01 00
> 50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
> 60: 10 00 01 00 e4 02 00 00 00 c8 00 0f 1c 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 08 a0 01 21 20 00 11 11 22 05 75 80 02 00 00 00
> 90: 56 04 51 02 00 08 ff 00 07 00 00 00 00 00 00 00
> a0: 08 c0 01 21 20 00 11 11 22 05 75 80 02 00 00 00
> b0: 13 56 13 04 00 00 00 00 03 00 00 00 00 00 00 00
> c0: 08 00 01 21 20 00 11 11 22 04 75 80 02 00 00 00
> d0: 56 04 51 02 00 00 07 00 07 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 03 00 00 00 00 00 ff 00 00 00 00 01 01 00 00 00
> 50: 00 00 00 01 02 00 00 00 00 00 00 01 03 00 00 00
> 60: 00 00 00 01 04 00 00 00 00 00 00 01 05 00 00 00
> 70: 00 00 00 01 06 00 00 00 00 00 00 01 07 00 00 00
> 80: 03 22 f9 00 20 6f f9 00 00 00 00 00 00 00 00 00
> 90: 03 00 f8 00 00 21 f9 00 03 00 e0 00 00 ff f7 00
> a0: 03 c0 fe 00 20 c0 fe 00 03 0a 00 00 00 0b 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 23 00 00 00 20 20 00 00 13 f0 ff 01 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 03 02 00 07 03 00 08 ff 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 01 00 00 00 00 00 00 00 01 20 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 de e0 0f 00 00 00 00 00 de e0 0f 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 55 00 00 00 00 00 00 00 42 35 82 13 21 0b 10 00
> 90: 00 8c 33 08 08 0a 7b 0e 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 8e d6 50 be 66 00 00 00 c5 34 0c 02 40 00 40 0c
> c0: 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: b6 d6 1e 5c 5e e1 8f 9f 78 25 36 ad 9e c2 1d 37
> e0: df f4 9e ff cd 60 eb 5f c5 0d 9d d6 c7 93 bf 37
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 03 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: ff 3b 00 00 44 00 40 02 00 00 00 00 00 00 00 00
> 50: f8 ff ff ff ff 00 00 00 00 00 02 00 40 44 1c 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 11 01 02 51 11 80 00 50 00 38 00 08 1b 22 00 00
> 80: 00 00 07 23 13 21 13 00 00 00 00 00 00 00 00 00
> 90: 07 00 00 00 70 00 00 00 00 d0 37 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 3f 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 07 07 e2 04 00 00 00 00 00 25 00 00
> e0: 00 00 00 00 20 0d 59 00 1b 01 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Capabilities: [80] #08 [2101]
> Capabilities: [a0] #08 [2101]
> Capabilities: [c0] #08 [2101]
> 00: 22 10 00 11 00 00 10 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 80 00 00 00 00 00 00 00 00 00 00 00
> 40: 04 04 01 00 01 01 05 00 01 01 01 00 01 01 01 00
> 50: 01 01 01 00 01 01 01 00 01 01 01 00 01 01 01 00
> 60: 11 00 01 00 e4 00 00 00 00 c8 00 0f 04 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 08 a0 01 21 d0 00 11 77 22 00 75 80 02 00 00 00
> 90: 02 30 10 06 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 08 c0 01 21 20 00 11 11 22 05 75 80 02 00 00 00
> b0: 13 56 13 04 00 00 00 00 03 00 00 00 00 00 00 00
> c0: 08 00 01 21 d0 00 11 77 22 00 75 80 02 00 00 00
> d0: 26 16 00 01 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 01 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 03 00 00 00 00 00 ff 00 00 00 00 01 01 00 00 00
> 50: 00 00 00 01 02 00 00 00 00 00 00 01 03 00 00 00
> 60: 00 00 00 01 04 00 00 00 00 00 00 01 05 00 00 00
> 70: 00 00 00 01 06 00 00 00 00 00 00 01 07 00 00 00
> 80: 03 22 f9 00 20 6f f9 00 00 00 00 00 00 00 00 00
> 90: 03 00 f8 00 00 21 f9 00 03 00 e0 00 00 ff f7 00
> a0: 03 c0 fe 00 20 c0 fe 00 03 0a 00 00 00 0b 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 23 00 00 00 20 20 00 00 13 f0 ff 01 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 03 02 00 07 03 00 08 ff 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 02 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 08 00 00 01 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 62 43 56 be 66 00 00 00 55 af 00 00 09 00 40 10
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 51 ff e2 ae c3 88 b6 82 06 0d e9 6e 35 d8 00 d1
> e0: 49 7f fb cc 53 d2 b6 ff 82 85 e5 3a 54 fb 84 ea
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> 00: 22 10 03 11 00 00 00 00 00 00 00 06 00 00 80 00
> 10: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: ff 3b 00 00 44 00 40 02 00 00 00 00 00 00 00 00
> 50: f8 7b 00 00 fa 00 00 00 00 00 02 00 80 00 20 10
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 11 01 02 51 11 80 00 50 00 38 00 08 1b 22 00 00
> 80: 00 00 07 23 13 21 13 00 00 00 00 00 00 00 00 00
> 90: 07 00 00 00 70 00 00 00 00 d0 37 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 3e 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 07 07 e2 04 00 00 00 00 00 25 25 00
> e0: 00 00 00 00 20 0c 59 00 1b 01 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:01:02.0 IDE interface: Silicon Image, Inc. (formerly CMD Technology Inc) SiI 3512 [SATALink/SATARaid] Serial ATA Controller (rev 01) (prog-if 85 [Master SecO PriO])
> Subsystem: IBM: Unknown device 3512
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, cache line size 10
> Interrupt: pin A routed to IRQ 17
> Region 0: I/O ports at 2020 [size=8]
> Region 1: I/O ports at 2014 [size=4]
> Region 2: I/O ports at 2018 [size=8]
> Region 3: I/O ports at 2010 [size=4]
> Region 4: I/O ports at 2000 [size=16]
> Region 5: Memory at f9520000 (32-bit, non-prefetchable) [size=512]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=2 PME-
> 00: 95 10 12 35 07 00 b0 02 01 85 01 01 10 40 00 00
> 10: 21 20 00 00 15 20 00 00 19 20 00 00 11 20 00 00
> 20: 01 20 00 00 00 00 52 f9 00 00 00 00 14 10 12 35
> 30: 00 00 00 00 60 00 00 00 00 00 00 00 09 01 00 00
> 40: 02 00 00 00 97 dd d2 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 01 00 22 06 00 40 00 64 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 60 00 00 00 cd de
> 80: 22 00 00 00 03 00 00 00 00 00 00 00 67 9d 76 1d
> 90: 00 00 00 08 ff ff 00 00 00 00 00 08 ff 00 00 00
> a0: 01 21 15 65 dd 62 dd 62 92 43 92 43 09 40 09 40
> b0: 01 21 15 65 dd 62 dd 62 92 43 92 43 09 40 09 40
> c0: 84 01 00 00 13 01 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:01:03.0 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
> Subsystem: IBM: Unknown device 02b7
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (250ns min, 10500ns max), cache line size 10
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f9530000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: 33 10 35 00 16 00 10 02 43 10 03 0c 10 40 80 00
> 10: 00 00 53 f9 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 01 01 2a
> 40: 01 00 02 7e 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 05 33 b0 6c 20 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:01:03.1 USB Controller: NEC Corporation USB (rev 43) (prog-if 10 [OHCI])
> Subsystem: IBM: Unknown device 02b7
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (250ns min, 10500ns max), cache line size 10
> Interrupt: pin B routed to IRQ 19
> Region 0: Memory at f9540000 (32-bit, non-prefetchable) [size=4K]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: 33 10 35 00 16 00 10 02 43 10 03 0c 10 40 00 00
> 10: 00 00 54 f9 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0b 02 01 2a
> 40: 01 00 02 7e 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:01:03.2 USB Controller: NEC Corporation USB 2.0 (rev 04) (prog-if 20 [EHCI])
> Subsystem: IBM: Unknown device 02b7
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 132 (4000ns min, 8500ns max), cache line size 10
> Interrupt: pin C routed to IRQ 16
> Region 0: Memory at f9550000 (32-bit, non-prefetchable) [size=256]
> Capabilities: [40] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> 00: 33 10 e0 00 16 00 10 02 04 20 03 0c 10 84 00 00
> 10: 00 00 55 f9 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 05 03 10 22
> 40: 01 00 02 7e 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 20 20 3f 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 05 33 b0 6c 20 00 00 00 01 00 00 00 00 00 08 c0
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:01:04.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
> Subsystem: IBM: Unknown device 02b7
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (500ns min, 1000ns max), cache line size 10
> Interrupt: pin A routed to IRQ 19
> Region 0: Memory at f9570000 (32-bit, non-prefetchable) [size=2K]
> Region 1: Memory at f9560000 (32-bit, non-prefetchable) [size=16K]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME+
> 00: 4c 10 23 80 16 00 10 02 00 10 00 0c 10 40 00 00
> 10: 00 00 57 f9 00 00 56 f9 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 02 04
> 40: 00 00 00 00 01 00 02 7e 00 80 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 08 00 00 00
> f0: 10 00 00 00 82 10 00 00 14 10 b7 02 00 00 00 00
>
> 0000:03:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5703X Gigabit Ethernet (rev 02)
> Subsystem: IBM: Unknown device 026f
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (16000ns min), cache line size 10
> Interrupt: pin A routed to IRQ 28
> Region 0: Memory at f9600000 (64-bit, non-prefetchable) [size=64K]
> Capabilities: [40] PCI-X non-bridge device.
> Command: DPERE- ERO- RBC=2 OST=0
> Status: Bus=3 Dev=2 Func=1 64bit+ 133MHz+ SCD- USC-, DC=simple, DMMRBC=2, DMOST=0, DMCRS=1, RSCEM- Capabilities: [48] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=1 PME-
> Capabilities: [50] Vital Product Data
> Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
> Address: 0260d4c6cb641f4c Data: b315
> 00: e4 14 a7 16 06 00 b0 02 02 00 00 02 10 40 00 00
> 10: 04 00 60 f9 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 6f 02
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 05 01 40 00
> 40: 07 48 08 00 11 03 43 04 01 50 02 c0 00 20 00 64
> 50: 03 58 44 00 f5 71 4e 18 05 00 86 00 4c 1f 64 cb
> 60: c6 d4 60 02 15 b3 00 00 98 00 02 10 00 40 9f 76
> 70: e2 10 00 00 a6 00 00 80 4c 5b 03 00 00 00 00 00
> 80: 00 00 00 00 02 37 98 90 34 00 13 04 82 10 08 00
> 90: 09 97 00 01 01 00 00 00 00 00 00 00 6e 01 00 00
> a0: 00 00 00 00 a6 00 00 00 00 00 00 00 aa 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:08:00.0 Host bridge: Advanced Micro Devices [AMD] AMD-8151 System Controller (rev 14)
> Subsystem: IBM: Unknown device 02b7
> Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
> Capabilities: [a0] AGP version 3.0
> Status: RQ=32 Iso- ArqSz=0 Cal=2 SBA+ ITACoh+ GART64- HTrans- 64bit+ FW+ AGP3+ Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
> Capabilities: [c0] #08 [0060]
> 00: 22 10 54 74 02 00 10 02 14 00 00 06 00 00 00 00
> 10: 08 00 00 e0 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 14 10 b7 02
> 30: 00 00 00 00 a0 00 00 00 00 00 00 00 00 00 00 00
> 40: 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 0b 00 19 00 0b 00 19 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 02 c0 30 00 3b 0b 00 1f 00 02 00 00 00 00 00 00
> b0: 00 01 00 00 00 0f 01 00 00 00 00 00 00 00 00 00
> c0: 08 00 60 00 20 00 11 11 20 00 00 00 22 05 35 00
> d0: 02 02 35 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 08 08 0d 00 08 08 0e 00 0f 0f 15 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:08:01.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8151 AGP Bridge (rev 14) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 99
> Bus: primary=08, secondary=09, subordinate=0d, sec-latency=68
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: f8000000-f8ffffff
> Prefetchable memory behind bridge: f0000000-f7ffffff
> BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
> 00: 22 10 55 74 07 00 20 02 14 00 04 06 00 63 01 00
> 10: 00 00 00 00 00 00 00 00 08 09 0d 44 f1 01 20 22
> 20: 00 f8 f0 f8 00 f0 f0 f7 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 ff 00 0c 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:08:03.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=08, secondary=0e, subordinate=12, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
> BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [a0] Capabilities: [b8] #08 [8000]
> Capabilities: [c0] #08 [0043]
> 00: 22 10 50 74 17 01 30 02 12 00 04 06 00 40 81 00
> 10: 00 00 00 00 00 00 00 00 08 0e 12 40 f1 01 20 22
> 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 a0 00 00 00 00 00 00 00 ff 00 07 00
> 40: 04 00 1f 00 01 00 00 00 02 0b 00 00 01 2c 00 00
> 50: 00 00 03 00 00 00 05 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 07 b8 83 00 18 08 03 00 0e 00 ff ff 02 00 ff ff
> b0: 00 00 00 00 00 00 00 00 08 c0 00 80 00 00 00 05
> c0: 08 00 43 00 20 00 11 00 d0 00 00 77 22 02 35 00
> d0: 02 00 35 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 0f 00 00 00 0d 00 00 00 15 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:08:03.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01) (prog-if 10 [IO-APIC])
> Subsystem: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f9200000 (64-bit, non-prefetchable) [size=4K]
> 00: 22 10 51 74 06 00 00 02 01 10 00 08 00 00 00 00
> 10: 04 00 20 f9 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 51 74
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 00 00 00 03 00 00 00 04 00 20 f9 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:08:04.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Bus: primary=08, secondary=13, subordinate=17, sec-latency=64
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fff00000-000fffff
> Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
> BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [a0] Capabilities: [b8] #08 [8000]
> 00: 22 10 50 74 17 01 30 02 12 00 04 06 00 40 81 00
> 10: 00 00 00 00 00 00 00 00 08 13 17 40 f1 01 20 22
> 20: f0 ff 00 00 f1 ff 01 00 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 a0 00 00 00 00 00 00 00 ff 00 07 00
> 40: 04 00 1f 00 01 00 00 00 00 00 00 00 01 2c 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 07 b8 83 00 20 08 03 00 0e 00 ff ff 02 00 ff ff
> b0: 00 00 00 00 00 00 00 00 08 00 00 80 00 00 00 06
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:08:04.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01) (prog-if 10 [IO-APIC])
> Subsystem: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f9210000 (64-bit, non-prefetchable) [size=4K]
> 00: 22 10 51 74 06 00 00 02 01 10 00 08 00 00 00 00
> 10: 04 00 21 f9 00 00 00 00 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 22 10 51 74
> 30: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 40: 00 00 00 00 03 00 00 00 04 00 21 f9 00 00 00 00
> 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> 0000:09:00.0 VGA compatible controller: nVidia Corporation NV36GL [Quadro FX 1100] (rev a1) (prog-if 00 [VGA])
> Subsystem: nVidia Corporation: Unknown device 01da
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (1250ns min, 250ns max)
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at f8000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at f0000000 (32-bit, prefetchable) [size=128M]
> Capabilities: [60] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [44] AGP version 3.0
> Status: RQ=32 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
> 00: de 10 4e 03 07 00 b0 02 a1 00 00 03 00 40 00 00
> 10: 00 00 00 f8 08 00 00 f0 00 00 00 00 00 00 00 00
> 20: 00 00 00 00 00 00 00 00 00 00 00 00 de 10 da 01
> 30: 00 00 00 00 60 00 00 00 00 00 00 00 05 01 05 01
> 40: de 10 da 01 02 00 30 00 1b 0e 00 1f 00 00 00 00
> 50: 01 00 00 00 01 00 00 00 ce d6 23 00 0f 00 00 00
> 60: 01 44 02 00 00 00 00 00 00 00 00 00 00 00 00 00
> 70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
prev parent reply other threads:[~2005-12-14 23:38 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-12-13 10:31 2.6.15-rc5-mm2 does not boot on AMD64 with sata_sil Muli Ben-Yehuda
2005-12-14 23:37 ` Jon Mason [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20051214233705.GA22464@us.ibm.com \
--to=jdmason@us.ibm.com \
--cc=jgarzik@pobox.com \
--cc=linux-kernel@vger.kernel.org \
--cc=muli@il.ibm.com \
--cc=mulix@mulix.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.