From: Kenny Simpson <theonetruekenny@yahoo.com>
To: linux kernel <linux-kernel@vger.kernel.org>
Subject: scsi errors with dpt-i2o driver
Date: Thu, 22 Dec 2005 06:43:48 -0800 (PST) [thread overview]
Message-ID: <20051222144348.85266.qmail@web34104.mail.mud.yahoo.com> (raw)
Hi,
We have been experiencing long system pauses (~30 seconds), and think we have tracked it down to
a scsi issue. The syslog just after the pause has:
Dec 22 04:12:06 tux224 kernel: dpti0: Trying to Abort cmd=264682
Dec 22 04:12:06 tux224 kernel: dpti0: Abort cmd not supported
Dec 22 04:12:06 tux224 kernel: dpti0: Trying to Abort cmd=264683
Dec 22 04:12:06 tux224 kernel: dpti0: Abort cmd not supported
Dec 22 04:12:06 tux224 kernel: dpti0: Trying to Abort cmd=264684
Dec 22 04:12:06 tux224 kernel: dpti0: Abort cmd not supported
Dec 22 04:12:06 tux224 kernel: dpti0: Trying to reset device
Dec 22 04:12:06 tux224 kernel: dpti0: Device reset not supported
Dec 22 04:12:06 tux224 kernel: dpti0: Bus reset: SCSI Bus 0: tid: 9
Dec 22 04:12:06 tux224 kernel: dpti0: Bus reset success.
The previous time seen by the system (as reported by sar with a 1-second frequency), was 04:11:29.
These errors seem to happen only every few days, and we have not found a means to reproduce them
on demand.
Are there any suggestions about how to diagnose further? What about trying the native i2o driver?
Details:
The machine is a dual Opteron rack-mount server.
kernel is 2.6.15-rc6 w/ preempt.
lspci:
0000:00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07)
0000:00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
0000:00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03)
0000:00:07.2 SMBus: Advanced Micro Devices [AMD] AMD-8111 SMBus 2.0 (rev 02)
0000:00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
0000:00:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12)
0000:00:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01)
0000:00:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12)
0000:00:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01)
0000:00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
0000:02:05.0 RAID bus controller: Adaptec (formerly DPT) SmartRAID V Controller (rev 01)
0000:02:09.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03)
0000:02:09.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704 Gigabit Ethernet (rev 03)
0000:03:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
0000:03:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b)
0000:03:06.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)
The scsi controller is model 2015s. The disks are Seagate Cheetah Ultra 320 - model ST336607LC.
Other potentially interresting messages from dmesg:
[ 1.490153] Loading Adaptec I2O RAID: Version 2.4 Build 5go
[ 1.496872] Detecting Adaptec I2O RAID controllers...
[ 1.502983] ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 26 (level, low) -> IRQ 169
[ 1.512165] Adaptec I2O RAID controller 0 irq=169
[ 1.517865] BAR0 f8880000 - size= 100000
[ 1.523127] BAR1 f8a00000 - size= 1000000
[ 3.391459] dpti: If you have a lot of devices this could take a few minutes.
[ 3.400032] dpti0: Reading the hardware resource table.
[ 13.298799] TID 008 Vendor: ADAPTEC Device: AIC-7902 Rev: 00000001
[ 13.309206] TID 009 Vendor: ADAPTEC Device: AIC-7902 Rev: 00000001
[ 13.324229] TID 523 Vendor: ADAPTEC R Device: RAID-10 Rev: 3B05D
[ 13.337469] scsi0 : Vendor: Adaptec Model: 2015S FW:3B05
[ 13.345860] Vendor: ADAPTEC Model: RAID-10 Rev: 3B05
[ 13.355339] Type: Direct-Access ANSI SCSI revision: 02
[ 13.365151] Adaptec aacraid driver (1.1-4 Dec 20 2005 09:00:40)
[ 13.372343] megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST 2005)
[ 13.381055] megaraid: 2.20.4.6 (Release Date: Mon Mar 07 12:27:22 EST 2005)
[ 13.389406] megasas: 00.00.02.00-rc4 Fri Sep 16 12:37:08 EDT 2005
[ 13.396752] 3ware 9000 Storage Controller device driver for Linux v2.26.02.004.
[ 13.413525] SCSI device sda: 143372288 512-byte hdwr sectors (73407 MB)
[ 13.424515] SCSI device sda: drive cache: write back
[ 13.432733] SCSI device sda: 143372288 512-byte hdwr sectors (73407 MB)
[ 13.443708] SCSI device sda: drive cache: write back
[ 13.449709] sda: sda1 sda2 < sda5 sda6 sda7 sda8 >
[ 13.505791] sd 0:0:0:0: Attached scsi disk sda
thanks,
-Kenny
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
next reply other threads:[~2005-12-22 14:43 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-12-22 14:43 Kenny Simpson [this message]
2005-12-22 14:56 ` scsi errors with dpt-i2o driver Arjan van de Ven
2005-12-22 20:03 ` Kenny Simpson
2005-12-23 16:39 ` Miquel van Smoorenburg
-- strict thread matches above, loose matches on Subject: below --
2005-12-22 16:31 Salyzyn, Mark
2005-12-22 16:54 ` Kenny Simpson
2005-12-22 17:04 ` Kenny Simpson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20051222144348.85266.qmail@web34104.mail.mud.yahoo.com \
--to=theonetruekenny@yahoo.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.