* [parisc-linux] J2240 - Almost There...
@ 2001-11-12 2:43 Craig D. Lansing (root)
2001-11-12 6:03 ` Jurriaan on Alpha
2001-11-12 10:49 ` Albert Strasheim
0 siblings, 2 replies; 25+ messages in thread
From: Craig D. Lansing (root) @ 2001-11-12 2:43 UTC (permalink / raw)
To: parisc-linux
After using my CD burner to create several nice coasters, I have been
able to create a couple of CD's from which my J2240 will attempt to
boot. I think that I am almost there, but need someone to show me the
error of my ways. Disclaimer: I am not a System Admin by trade. I have
been an HP-UX user since about version 7, but have not had a box of my
own to play with until I pulled this J2240 from the trash. The system
is a J2240 2-way, 2.5GB RAM, 2x8GB internal FW-SCSI Disks, DDS-III,
internal Toshiba SCSI CD-ROM, 21" graphics console.
Here's what I get when I try to boot from the 0.9.2 iso CD after
changing my boot path to the internal CD-ROM (SESCSI.2.0):
Boot IO Dependent Code (IODC) revision 153
HARD Booted
palo ipl 0.92 root@spqr Mon Jun 25 23:03:13 CEST 2001
0/vmlinux32 2853588 bytes @ 0x6ad6800
0/vmlinux64 3585851 bytes @ 0x6d8f800
0/ramdisk 1991209 bytes @ 0x70fb000
Command Line: 'root=/dev/ram console=tty0 sti=0 sti_font=VGA8x16
TERM=linux'
Kernel: partition 0 file /vmlinux
Ramdisk: partition 0 file /ramdisk
Warning: Kernel name doesn't end with 32 or 64... Guessing 32
ELF32 executable
Entry 00100000 first 00100000 n 4
Segment 0 load 010000000 size 1606948 mediaptr 0x1000
Segment 1 load 0028a000 size 468472 mediaptr 0x18a000
Segment 2 load 00300000 size 8192 mediaptr 0x1fd000
Segment 3 load 0034bea8 size 80688 mediaptr 0x1ffea8
Loading ramdisk 1991209 bytes @ 3fe09000...
branch to kernel entry point 0x00100000
Set default PSW W bit to 0
<System hangs here>
---------------------------------------------------------------------------
Booting from the 0.9 sti iso CD gives the above and goes a little
further:
[snip]
CPUID Vers 14 rev 23
Model 9000/782/J2240
[snip]
Found devices:
1. SummitHawk Dino RS-232(10)....
[snip]
18. SummitHawk memory(1)
[snip]
Kernel command line HOME=/ TERM=linux root=/dev/ram console=tty0 sti=0
sti_font=VGA8x16
Console: colour dummy device 80x25
<System hangs here>
---------------------------------------------------------------------------
TIA,
Craig
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost There...
2001-11-12 2:43 [parisc-linux] J2240 - Almost There Craig D. Lansing (root)
@ 2001-11-12 6:03 ` Jurriaan on Alpha
2001-11-13 0:07 ` Craig D. Lansing
2001-11-12 10:49 ` Albert Strasheim
1 sibling, 1 reply; 25+ messages in thread
From: Jurriaan on Alpha @ 2001-11-12 6:03 UTC (permalink / raw)
To: Craig D. Lansing (root); +Cc: parisc-linux
On Sun, Nov 11, 2001 at 09:43:18PM -0500, Craig D. Lansing (root) wrote:
> After using my CD burner to create several nice coasters, I have been
> able to create a couple of CD's from which my J2240 will attempt to
> boot. I think that I am almost there, but need someone to show me the
> error of my ways. Disclaimer: I am not a System Admin by trade. I have
> been an HP-UX user since about version 7, but have not had a box of my
> own to play with until I pulled this J2240 from the trash. The system
> is a J2240 2-way, 2.5GB RAM, 2x8GB internal FW-SCSI Disks, DDS-III,
> internal Toshiba SCSI CD-ROM, 21" graphics console.
We know the story. Now don't mention it again, because we'll go green
with envy and look elsewhere :-)
> Command Line: 'root=/dev/ram console=tty0 sti=0 sti_font=VGA8x16
> TERM=linux'
>
Shouldn't that be ttyS0 for the console?
Good luck,
Jurriaan
--
Go not unto the Usenet for advice, for you will be told both yea and nay (and
quite a few things that just have nothing at all to do with the question).
seen in a .sig somewhere
GNU/Linux 2.4.13-ac8 on Debian/Alpha 64-bits 990 bogomips load:1.33 1.47 1.20
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost There...
2001-11-12 2:43 [parisc-linux] J2240 - Almost There Craig D. Lansing (root)
2001-11-12 6:03 ` Jurriaan on Alpha
@ 2001-11-12 10:49 ` Albert Strasheim
1 sibling, 0 replies; 25+ messages in thread
From: Albert Strasheim @ 2001-11-12 10:49 UTC (permalink / raw)
To: Craig D. Lansing (root); +Cc: parisc-linux
Hello,
What I would do is the following:
1. Get the latest working kernel from ftp.parisc-linux.org
(linux-20011108 should do).
2. Compile (or cross-compile with xc-latest) it, and use tftp/bootp (I
think?) to boot the resulting lifimage from make palo. See how far that
gets you.
Regards,
Albert
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost There...
2001-11-13 0:07 ` Craig D. Lansing
@ 2001-11-13 0:04 ` Matthew Wilcox
2001-11-13 0:11 ` John David Anglin
` (2 subsequent siblings)
3 siblings, 0 replies; 25+ messages in thread
From: Matthew Wilcox @ 2001-11-13 0:04 UTC (permalink / raw)
To: Craig D. Lansing; +Cc: thunder7, parisc-linux
On Mon, Nov 12, 2001 at 07:07:35PM -0500, Craig D. Lansing wrote:
> Today, I rescued a 700/96 and cable from the trash so I'm going to try to
> use it as a serial console to see how far I get. It's amazing the "junk"
> that shows up in the trash when your HP shop gets bought out by an IBM shop.
> Anybody need a few K580x4's, 4GB RAM, and a couple of fully loaded AutoRaid
> cabinets each? In the meantime, how do I change the "Command Line" at boot?
> Do I have to "interact" with IPL (almost as bad as having to interact with
> people :-) ?
The K580s are definitely of interest...
Yes, interacting with IPL (or ISL on some models) is how you change
the command line params; you get a nifty little menu and can edit the
arguments.
--
Revolutions do not require corporate support.
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost There...
2001-11-12 6:03 ` Jurriaan on Alpha
@ 2001-11-13 0:07 ` Craig D. Lansing
2001-11-13 0:04 ` Matthew Wilcox
` (3 more replies)
0 siblings, 4 replies; 25+ messages in thread
From: Craig D. Lansing @ 2001-11-13 0:07 UTC (permalink / raw)
To: thunder7; +Cc: parisc-linux
Today, I rescued a 700/96 and cable from the trash so I'm going to try to
use it as a serial console to see how far I get. It's amazing the "junk"
that shows up in the trash when your HP shop gets bought out by an IBM shop.
Anybody need a few K580x4's, 4GB RAM, and a couple of fully loaded AutoRaid
cabinets each? In the meantime, how do I change the "Command Line" at boot?
Do I have to "interact" with IPL (almost as bad as having to interact with
people :-) ?
----- Original Message -----
From: Jurriaan on Alpha <thunder7@xs4all.nl>
To: Craig D. Lansing (root) <lansing@beldar.com>
Cc: <parisc-linux@lists.parisc-linux.org>
Sent: Monday, November 12, 2001 1:03 AM
Subject: Re: [parisc-linux] J2240 - Almost There...
> On Sun, Nov 11, 2001 at 09:43:18PM -0500, Craig D. Lansing (root) wrote:
> > After using my CD burner to create several nice coasters, I have been
> > able to create a couple of CD's from which my J2240 will attempt to
> > boot. I think that I am almost there, but need someone to show me the
> > error of my ways. Disclaimer: I am not a System Admin by trade. I have
> > been an HP-UX user since about version 7, but have not had a box of my
> > own to play with until I pulled this J2240 from the trash. The system
> > is a J2240 2-way, 2.5GB RAM, 2x8GB internal FW-SCSI Disks, DDS-III,
> > internal Toshiba SCSI CD-ROM, 21" graphics console.
>
> We know the story. Now don't mention it again, because we'll go green
> with envy and look elsewhere :-)
>
> > Command Line: 'root=/dev/ram console=tty0 sti=0 sti_font=VGA8x16
> > TERM=linux'
> >
> Shouldn't that be ttyS0 for the console?
>
> Good luck,
> Jurriaan
> --
> Go not unto the Usenet for advice, for you will be told both yea and nay
(and
> quite a few things that just have nothing at all to do with the question).
> seen in a .sig somewhere
> GNU/Linux 2.4.13-ac8 on Debian/Alpha 64-bits 990 bogomips load:1.33 1.47
1.20
>
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost There...
2001-11-13 0:07 ` Craig D. Lansing
2001-11-13 0:04 ` Matthew Wilcox
@ 2001-11-13 0:11 ` John David Anglin
2001-11-13 7:40 ` Grant Grundler
2001-11-13 9:03 ` nick
3 siblings, 0 replies; 25+ messages in thread
From: John David Anglin @ 2001-11-13 0:11 UTC (permalink / raw)
To: Craig D. Lansing; +Cc: thunder7, parisc-linux
> Today, I rescued a 700/96 and cable from the trash so I'm going to try to
> use it as a serial console to see how far I get. It's amazing the "junk"
> that shows up in the trash when your HP shop gets bought out by an IBM shop.
> Anybody need a few K580x4's, 4GB RAM, and a couple of fully loaded AutoRaid
> cabinets each? In the meantime, how do I change the "Command Line" at boot?
Where do I send the truck!
Dave
--
J. David Anglin dave.anglin@nrc.ca
National Research Council of Canada (613) 990-0752 (FAX: 952-6605)
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost There...
2001-11-13 0:07 ` Craig D. Lansing
2001-11-13 0:04 ` Matthew Wilcox
2001-11-13 0:11 ` John David Anglin
@ 2001-11-13 7:40 ` Grant Grundler
2001-11-13 9:03 ` nick
3 siblings, 0 replies; 25+ messages in thread
From: Grant Grundler @ 2001-11-13 7:40 UTC (permalink / raw)
To: Craig D. Lansing; +Cc: parisc-linux
"Craig D. Lansing" wrote:
...
> In the meantime, how do I change the "Command Line" at boot?
> Do I have to "interact" with IPL (almost as bad as having to interact with
> people :-) ?
Yes. Adding new params is less obvious: edit any param and append ' '
plus the new param.
grant
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost There...
2001-11-13 0:07 ` Craig D. Lansing
` (2 preceding siblings ...)
2001-11-13 7:40 ` Grant Grundler
@ 2001-11-13 9:03 ` nick
3 siblings, 0 replies; 25+ messages in thread
From: nick @ 2001-11-13 9:03 UTC (permalink / raw)
To: Craig D. Lansing; +Cc: thunder7, parisc-linux
On Mon, 12 Nov 2001, Craig D. Lansing wrote:
> Today, I rescued a 700/96 and cable from the trash so I'm going to try to
> use it as a serial console to see how far I get. It's amazing the "junk"
> that shows up in the trash when your HP shop gets bought out by an IBM shop.
> Anybody need a few K580x4's, 4GB RAM, and a couple of fully loaded AutoRaid
> cabinets each? In the meantime, how do I change the "Command Line" at boot?
> Do I have to "interact" with IPL (almost as bad as having to interact with
> people :-) ?
Heh, I'm sure almost everyone on this list would love to aquire a K580. I
know I would!
Nick
^ permalink raw reply [flat|nested] 25+ messages in thread
* [parisc-linux] J2240 - Almost there....
@ 2005-12-30 15:51 Craig D. Lansing
2005-12-30 20:09 ` Kyle McMartin
0 siblings, 1 reply; 25+ messages in thread
From: Craig D. Lansing @ 2005-12-30 15:51 UTC (permalink / raw)
To: parisc-linux
[-- Attachment #1.1: Type: text/plain, Size: 1301 bytes --]
I have an old J2240 w/ p1120 console that I was going to throw away, but
decided to load the most recent PA-RISC Linux instead. I had loaded and
gotten it running from the PA-RISC project several years ago. Using the
ISO's from 12/19/05 I was able to successfully install on one of the hdd's
(FWSCSI.5.0), but cannot boot to a prompt. When booting from path FWSCSI.5.0
I get the 2 Tux images, a long list of console output, and get the point
below and it freezes. I have tried booting using a serial console, but
cannot get connected to the serial port. Any ideas on how to proceed from
here?
End of console output:
----------------------------------------------------------------------------
--------------------------------------------------------
Starting hotplug subsystem:
pci
tulip: already loaded
defxx.c:v1.06 2003/08/04 Lawrence V. Stephani and others
fddi%d: DEFPA at I/O addr = 0x100, IRQ = 96, Hardware addr =
58-B0-60-00-00-00
----------------------------------------------------------------------------
---------------------------------------------------------
Other info.:
SESCSI.3.0 = HP C1537A Tape
SESCSI.2.0 = Toshiba CD-ROM (used for install)
FWSCSI.6.0 = IBM HDD (HP-UX 10.0)
FWSCSI.5.0 = IBM HDD (Linux)
[-- Attachment #1.2: Type: text/html, Size: 5132 bytes --]
[-- Attachment #2: Type: text/plain, Size: 169 bytes --]
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost there....
2005-12-30 15:51 [parisc-linux] J2240 - Almost there Craig D. Lansing
@ 2005-12-30 20:09 ` Kyle McMartin
2005-12-31 3:16 ` Craig D. Lansing
2005-12-31 14:43 ` [parisc-linux] " Max Grabert
0 siblings, 2 replies; 25+ messages in thread
From: Kyle McMartin @ 2005-12-30 20:09 UTC (permalink / raw)
To: Craig D. Lansing; +Cc: parisc-linux
On Fri, Dec 30, 2005 at 10:51:22AM -0500, Craig D. Lansing wrote:
> defxx.c:v1.06 2003/08/04 Lawrence V. Stephani and others
> fddi%d: DEFPA at I/O addr = 0x100, IRQ = 96, Hardware addr = 58-B0-60-00-00-00
I'm going to take a stab and say this is your problem. You're likely going
to see a HPMC chassis code however this machine displays such a thing (look
up the LED code, or it should display it right on an LCD if it was one.)
[Thanks for identifying a piece of non-working hardware.]
To work around this, you have two options:
1 - Remove the expansion card, if possible.
2 - Boot single user, (append single to the PALO/IPL command line)
2.1 - Edit/create /etc/hotplug/blacklist.d/parisc and
add the module name (probably defxx) to the file.
If other modules give you grief, repeat the step to blacklist them.
I'll make sure this module doesn't get built into the kernel, the driver
is probably written non-portably, and thus fails miserably on 'odd'
hardware like parisc.
Cheers,
Kyle
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* RE: [parisc-linux] J2240 - Almost there....
2005-12-30 20:09 ` Kyle McMartin
@ 2005-12-31 3:16 ` Craig D. Lansing
2005-12-31 3:30 ` Kyle McMartin
2005-12-31 14:43 ` [parisc-linux] " Max Grabert
1 sibling, 1 reply; 25+ messages in thread
From: Craig D. Lansing @ 2005-12-31 3:16 UTC (permalink / raw)
To: 'Kyle McMartin'; +Cc: parisc-linux
I tried adding "single" to various parts of the PALO command line. No luck.
Since the error at least looks like it is related to the FDDI card, I
re-installed using the other NIC as my primary (eth1). No difference.
The LCD just keeps cycling through...
FLT 5108.8-2-32
FLT 5408.8-2-32
FLT 5505.8-2-32
FLT CBF4.8-2-32
FLT CBFC.8-2-32
FLT CBF0.8-2-32
The system is in my den and not very accessible to take apart and start
pulling cards.
I guess I should have gone with my original plan to load this thing in my
truck and haul it to the dump, but now I'm determined to make it work. Any
other ideas?
-----Original Message-----
From: Kyle McMartin [mailto:kyle@mcmartin.ca]
Sent: Friday, December 30, 2005 3:09 PM
To: Craig D. Lansing
Cc: parisc-linux@lists.parisc-linux.org
Subject: Re: [parisc-linux] J2240 - Almost there....
On Fri, Dec 30, 2005 at 10:51:22AM -0500, Craig D. Lansing wrote:
> defxx.c:v1.06 2003/08/04 Lawrence V. Stephani and others
> fddi%d: DEFPA at I/O addr = 0x100, IRQ = 96, Hardware addr =
58-B0-60-00-00-00
I'm going to take a stab and say this is your problem. You're likely going
to see a HPMC chassis code however this machine displays such a thing (look
up the LED code, or it should display it right on an LCD if it was one.)
[Thanks for identifying a piece of non-working hardware.]
To work around this, you have two options:
1 - Remove the expansion card, if possible.
2 - Boot single user, (append single to the PALO/IPL command line)
2.1 - Edit/create /etc/hotplug/blacklist.d/parisc and
add the module name (probably defxx) to the file.
If other modules give you grief, repeat the step to blacklist them.
I'll make sure this module doesn't get built into the kernel, the driver
is probably written non-portably, and thus fails miserably on 'odd'
hardware like parisc.
Cheers,
Kyle
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost there....
2005-12-31 3:16 ` Craig D. Lansing
@ 2005-12-31 3:30 ` Kyle McMartin
2005-12-31 16:21 ` Craig D. Lansing
0 siblings, 1 reply; 25+ messages in thread
From: Kyle McMartin @ 2005-12-31 3:30 UTC (permalink / raw)
To: Craig D. Lansing; +Cc: parisc-linux
On Fri, Dec 30, 2005 at 10:16:59PM -0500, Craig D. Lansing wrote:
> I tried adding "single" to various parts of the PALO command line. No luck.
> Since the error at least looks like it is related to the FDDI card, I
> re-installed using the other NIC as my primary (eth1). No difference.
>
Bah. Instead of single use "init=/bin/sh" and run mount -o remount,rw /
to remount your root fs read-write, then follow the same step.
Definitely sounds like an HPMC because of a bad driver. What types
of expansion card do you have in that thing?
[You really shouldn't just throw it out, it's quite a nice box...]
Cheers,
Kyle
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* [parisc-linux] Re: J2240 - Almost there....
2005-12-30 20:09 ` Kyle McMartin
2005-12-31 3:16 ` Craig D. Lansing
@ 2005-12-31 14:43 ` Max Grabert
1 sibling, 0 replies; 25+ messages in thread
From: Max Grabert @ 2005-12-31 14:43 UTC (permalink / raw)
To: Kyle McMartin; +Cc: parisc-linux
[-- Attachment #1: Type: text/plain, Size: 1905 bytes --]
On 30/12/05, Kyle McMartin <kyle@mcmartin.ca> wrote:
> On Fri, Dec 30, 2005 at 10:51:22AM -0500, Craig D. Lansing wrote:
> > defxx.c:v1.06 2003/08/04 Lawrence V. Stephani and others
> > fddi%d: DEFPA at I/O addr = 0x100, IRQ = 96, Hardware addr =
> 58-B0-60-00-00-00
>
> I'm going to take a stab and say this is your problem. You're likely going
> to see a HPMC chassis code however this machine displays such a thing (look
> up the LED code, or it should display it right on an LCD if it was one.)
>
> [Thanks for identifying a piece of non-working hardware.]
BTW, this is a DEC FDDI card, those were usually the ones sold by HP/Compaq.
DEFPA is known not to work on 2.6 ... on any platform. Which is kind
of sad since
all the BSDs have a working driver and it is a nice piece of hardware.
I contacted the maintainer a couple of months ago, but he was busy
with other projects,
and he said he wanted to completely rewrite the driver, but it is
rather low priority for him
right now. I also gave it a try to fix the driver, but I soon found
out that it is more effort
to fix the driver than to rewrite it from scratch.
The only supported and working FDDI cards under linux are the ones
from Sysconnect,
however those cards have a GPL-only driver and there exists no driver
for the BSDs.
> To work around this, you have two options:
>
> 1 - Remove the expansion card, if possible.
>
> 2 - Boot single user, (append single to the PALO/IPL command line)
> 2.1 - Edit/create /etc/hotplug/blacklist.d/parisc and
> add the module name (probably defxx) to the file.
>
> If other modules give you grief, repeat the step to blacklist them.
>
> I'll make sure this module doesn't get built into the kernel, the driver
> is probably written non-portably, and thus fails miserably on 'odd'
> hardware like parisc.
No, it's much worse than that :-P
5 years of bit-rot leaves its marks.
Greetings,
Max
[-- Attachment #2: Type: text/plain, Size: 169 bytes --]
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* RE: [parisc-linux] J2240 - Almost there....
2005-12-31 3:30 ` Kyle McMartin
@ 2005-12-31 16:21 ` Craig D. Lansing
2005-12-31 18:08 ` Grant Grundler
0 siblings, 1 reply; 25+ messages in thread
From: Craig D. Lansing @ 2005-12-31 16:21 UTC (permalink / raw)
To: 'Kyle McMartin'; +Cc: parisc-linux
That worked, Thanx!!!! I added both defxx and DEFPA to
/etc/hotplug/blacklist.d/parisc to be safe.
I am now able to boot and have completed the install.
$uname -a
Linux howlin 2.6.8-2-32-smp #1 SMP Wed Aug 24 17:55:41 UTC 2005 parisc
GNU/Linux
OK, I have a little work to do with the h/w clock, but it's a start.
As far as what cards (or anything else) are in there I don't really remember
and it is not in a really good place to access the rear panel at all :-(
I'm sure of 2x CPUs, 2 FWSCSI 9GB HDD, DDS 3 Tape, Toshiba CD-ROM, and
probably redundant Ethernet/FDDI cards. Unfortunately, the system + console
on top of it weight in at what feels like a ton :-) If I could remember the
root password (ergh!), I could poke around in SAM on the HP-UX partition.
It boots to CDE, but I can't remember a single login. The J2240 was a gift
from a client who was an HP shop and was bought by a BigBlue company. They
gradually had to get rid of their HP equipment. They called me one day
several years ago and said they were going to throw away this J2240 and the
HP p1120 console (brand new... 1 day old) and I could have it... so I took
it. Be careful what you ask for.........
-----Original Message-----
From: Kyle McMartin [mailto:kyle@mcmartin.ca]
Sent: Friday, December 30, 2005 10:31 PM
To: Craig D. Lansing
Cc: parisc-linux@lists.parisc-linux.org
Subject: Re: [parisc-linux] J2240 - Almost there....
On Fri, Dec 30, 2005 at 10:16:59PM -0500, Craig D. Lansing wrote:
> I tried adding "single" to various parts of the PALO command line. No
luck.
> Since the error at least looks like it is related to the FDDI card, I
> re-installed using the other NIC as my primary (eth1). No difference.
>
Bah. Instead of single use "init=/bin/sh" and run mount -o remount,rw /
to remount your root fs read-write, then follow the same step.
Definitely sounds like an HPMC because of a bad driver. What types
of expansion card do you have in that thing?
[You really shouldn't just throw it out, it's quite a nice box...]
Cheers,
Kyle
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost there....
2005-12-31 16:21 ` Craig D. Lansing
@ 2005-12-31 18:08 ` Grant Grundler
2006-01-01 4:21 ` Craig D. Lansing
0 siblings, 1 reply; 25+ messages in thread
From: Grant Grundler @ 2005-12-31 18:08 UTC (permalink / raw)
To: Craig D. Lansing; +Cc: parisc-linux
On Sat, Dec 31, 2005 at 11:21:48AM -0500, Craig D. Lansing wrote:
> If I could remember the
> root password (ergh!), I could poke around in SAM on the HP-UX partition.
You don't need to remember the root login.
Answer "Y" to "Interact with ISL" type "hpux -is" at the ISL prompt.
You'll be root in single user mode.
"There is no such thing as computer security without physical security."
grant
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* RE: [parisc-linux] J2240 - Almost there....
2005-12-31 18:08 ` Grant Grundler
@ 2006-01-01 4:21 ` Craig D. Lansing
2006-01-01 6:32 ` Grant Grundler
0 siblings, 1 reply; 25+ messages in thread
From: Craig D. Lansing @ 2006-01-01 4:21 UTC (permalink / raw)
To: 'Grant Grundler'; +Cc: parisc-linux
Duh!!! Can you tell that it has been a long time since I've had a "real"
computer to play with?
Anyway, I now have a dual-boot (HP-UX 10 / Debian Linux) J2240.
Here's what SAM thinks is in the system:
Toshiba CD-ROM SCSI drive
IBM DDRS-39130WS (9GB disk)
IBM DDRS-39130WS (9GB disk)
FDDI (lan1)
100Base-T (lan0)
Cards
Built-in RS-232 Interface
Ultra2 Wide SCSI
Built-in Parallel Interface
Built-in Keyboard/Mouse
Built-in RS-232 Interface (yes, another one)
Device List
I/O Adapter
PCI Bus Bridge - GSCtoPCI
PCI(10110019) -- 3
PCI FDDI Adapter
PCI Bus Bridge - GSCtoPCI
Ultra2 Wide SCSI
IBM DDRS-39130WS
IBM DDRS-39130WS
Initiator
PCI(10110019) -- Built-in #2
Core I/O Adapter
Built-in Parallel Interface
Audio Interface
Built-in SCSI
Toshiba CD-ROM SCSI Drive
C1537A 12 GB DDS3 Data Compression Tape Drive
Initiator
Built-in Keyboard/Mouse
I/O Adapter
PCI Bus Bridge - GSCtoPCI
PCI(103c1005) -- 0
Built-in RS-232 Interface
Processor
Processor
Memory
Thanks for the help!!!!
-----Original Message-----
From: Grant Grundler [mailto:grundler@parisc-linux.org]
Sent: Saturday, December 31, 2005 1:08 PM
To: Craig D. Lansing
Cc: parisc-linux@lists.parisc-linux.org
Subject: Re: [parisc-linux] J2240 - Almost there....
On Sat, Dec 31, 2005 at 11:21:48AM -0500, Craig D. Lansing wrote:
> If I could remember the
> root password (ergh!), I could poke around in SAM on the HP-UX partition.
You don't need to remember the root login.
Answer "Y" to "Interact with ISL" type "hpux -is" at the ISL prompt.
You'll be root in single user mode.
"There is no such thing as computer security without physical security."
grant
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost there....
2006-01-01 4:21 ` Craig D. Lansing
@ 2006-01-01 6:32 ` Grant Grundler
2006-01-01 14:15 ` Thibaut VARENE
2006-01-03 2:01 ` Craig D. Lansing
0 siblings, 2 replies; 25+ messages in thread
From: Grant Grundler @ 2006-01-01 6:32 UTC (permalink / raw)
To: Craig D. Lansing; +Cc: parisc-linux
On Sat, Dec 31, 2005 at 11:21:06PM -0500, Craig D. Lansing wrote:
> Duh!!! Can you tell that it has been a long time since I've had a "real"
> computer to play with?
>
> Anyway, I now have a dual-boot (HP-UX 10 / Debian Linux) J2240.
>
> Here's what SAM thinks is in the system:
"ioscan -fk" is the preferred output and I can
better understand what is in the box.
I don't understand what's really built-in or add-on
with the SAM output.
thanks,
grant
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost there....
2006-01-01 6:32 ` Grant Grundler
@ 2006-01-01 14:15 ` Thibaut VARENE
2006-01-03 1:19 ` Craig D. Lansing
2006-01-03 2:01 ` Craig D. Lansing
1 sibling, 1 reply; 25+ messages in thread
From: Thibaut VARENE @ 2006-01-01 14:15 UTC (permalink / raw)
To: Grant Grundler; +Cc: parisc-linux
On 1/1/06, Grant Grundler <grundler@parisc-linux.org> wrote:
> On Sat, Dec 31, 2005 at 11:21:06PM -0500, Craig D. Lansing wrote:
> > Duh!!! Can you tell that it has been a long time since I've had a "rea=
l"
> > computer to play with?
> >
> > Anyway, I now have a dual-boot (HP-UX 10 / Debian Linux) J2240.
> >
> > Here's what SAM thinks is in the system:
>
> "ioscan -fk" is the preferred output and I can
> better understand what is in the box.
> I don't understand what's really built-in or add-on
> with the SAM output.
And while you're at it, i'd love to have the output of 'cat
/proc/cpuinfo' 'cat /proc/iomem' 'cat /proc/ioports' 'cat
/proc/interrupts/' and 'dmesg' from Linux to add to this growing list
:
http://www.pateam.org/archive/logs/ ;)
Thx and happy new year to every one!
T-Bone
--
Thibaut VARENE
http://www.parisc-linux.org/~varenet/
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* RE: [parisc-linux] J2240 - Almost there....
2006-01-01 14:15 ` Thibaut VARENE
@ 2006-01-03 1:19 ` Craig D. Lansing
2006-01-03 2:01 ` Matthew Wilcox
2006-01-04 17:43 ` Grant Grundler
0 siblings, 2 replies; 25+ messages in thread
From: Craig D. Lansing @ 2006-01-03 1:19 UTC (permalink / raw)
To: 'Thibaut VARENE', 'Grant Grundler'; +Cc: parisc-linux
Sorry that it took so long to reply. I spent most of the day driving to /
from Washington, DC yesterday. Re-installed and ran into problems as
follows:
1) Got gdm prompt (black&white, really large), but was able to login. Mouse
was not recognized after that so I was "stuck" in the desktop. I was able
to login OK in single user command line mode.
2) Re-installed after getting the actual "advanced" HP p1120 console specs
(instead of "simple"). Re-install failed due to "SMP CALL FUNCTION TIMED
OUT! (cpu=0), try ###" errors (I powered off the box after about 2000 of
these). Rebooted and got message to run "dpkg --configure -a". Did that
and packages installed. The system now tries to start gdm (flickers a lot),
but ultimately just goes to a blinking cursor When I reboot (shutdown -r 0)
I now get the "Welcome to your new Debian system" prompt. I guess maybe I
should re-install again????
3) Networking appears to not be working, I assumed that is because of the
"blacklisted" FDDI card (defxx,DEFPA). The box has an internal IP address
192.168.1.100 and I can't even ping it. However, I cannot ping the box when
booted into HP-UX either (192.168.1.200). Bad card (I tried the obvious of
another cable)????
To get the info. requsted below w/o a LAN, I "cheated" and started a getty
against a serial port, logged in via a Reflection session, and logged to an
output file... not pretty, but functional. Sorry if this is more than you
wanted to see. I have been unsuccessful trying to set up an entry in
/etc/inittab in HP-UX that will spawn a getty on the serial port equivalent
to ttyS0 in Linux... any pointers would be appreciated (it has been a long
time) then I can get the ioscan -fk output.
*******************************************
Linux Info
*******************************************
Debian GNU/Linux 3.1 howlin ttyS0
howlin login:
Debian GNU/Linux 3.1 howlin ttyS0
howlin login: root
Password:
Linux howlin 2.6.8-2-32-smp #1 SMP Wed Aug 24 17:55:41 UTC 2005 parisc
GNU/Linux
The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.
Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted
by applicable law.
howlin:~#
howlin:~# cat /proc/cpuinfo
processor : 0
cpu family : PA-RISC 2.0
cpu : PA8200 (PCX-U+)
cpu MHz : 236.000000
model : 9000/782/J2240
model name : SummitHawk U+
hversion : 0x00005b50
sversion : 0x00000491
I-cache : 2048 KB
D-cache : 2048 KB (WB, 0-way associative)
ITLB entries : 120
DTLB entries : 120 - shared with ITLB
BTLB fixed : max. 16384 pages, pagesize=4096 (64MB)
BTLB fix-entr. : 0 instruction, 0 data (16 combined) BTLB var-entr. : 0
instruction, 0 data (0 combined)
bogomips : 470.22
software id : 2002047818
processor : 1
cpu family : PA-RISC 2.0
cpu : PA8200 (PCX-U+)
cpu MHz : 236.000000
model : 9000/782/J2240
model name : SummitHawk U+
hversion : 0x00005b50
sversion : 0x00000491
I-cache : 2048 KB
D-cache : 2048 KB (WB, 0-way associative)
ITLB entries : 120
DTLB entries : 120 - shared with ITLB
BTLB fixed : max. 16384 pages, pagesize=4096 (64MB)
BTLB fix-entr. : 0 instruction, 0 data (16 combined) BTLB var-entr. : 0
instruction, 0 data (0 combined)
bogomips : 470.22
software id : 2002047818
howlin:~# cat /proc/iomem
00000000-7fffffff : System RAM
00000000-000009ff : PDC data (Page Zero)
00100000-003b4fff : Kernel code
003b5000-00513b03 : Kernel data
f0190000-f0190000 : lcd_cmd
f0190001-f0190001 : lcd_data
f1600000-f3ffffff : GSC Bus [10/]
f1604000-f1604fff : Cujo
f1607800-f1607807 : serial
f1800000-f1ffffff : Cujo LMMIO 0
f4000000-f5ffffff : GSC Bus [8/]
f6000000-f7ffffff : GSC Bus [10/]
f6000000-f7ffffff : Cujo LMMIO 1
f6000000-f7ffffff : 0000:02:00.0
f6100000-f64fffff : stifb mmio
f7000000-f71fffff : stifb fb
f8000000-fff7ffff : GSC Bus [8/]
fc000000-fc000fff : Cujo
fc003800-fc003807 : serial
fc004000-fc004fff : Dino [8/4]
fc800000-fcffffff : Dino [8/4] LMMIO 0
fc800000-fc800fff : 0000:01:13.0
fc800000-fc800fff : sym53c8xx
fc801000-fc8010ff : 0000:01:13.0
fc801000-fc8010ff : sym53c8xx
fc802000-fc80207f : 0000:01:14.0
fc802000-fc80207f : tulip
fd800000-fdffffff : Cujo LMMIO 0
fd800000-fd80ffff : 0000:00:04.0
fd810000-fd81007f : 0000:00:03.0
fd810000-fd81007f : tulip
fd811000-fd81107f : 0000:00:04.0
ffd00000-ffdfffff : Lasi
ffd00000-ffd00fff : Lasi
ffd06000-ffd06fff : Lasi SCSI
ffd08000-ffd08fff : GSC PS2
fff80000-fffaffff : Central Bus
fff88000-fff88fff : U2:Uturn
fff8a000-fff8afff : U2:Uturn
fffa0000-fffa0fff : CPU
fffa2000-fffa2fff : CPU
fffb0000-fffdffff : Local Broadcast
fffe0000-ffffffff : Global Broadcast
howlin:~# cat /proc/ioports
00000000-0000ffff : Cujo I/O Port
00000080-000000ff : 0000:00:03.0
00000080-000000ff : tulip
00000100-0000017f : 0000:00:04.0
00010000-0001ffff : Dino I/O Port
00010000-000100ff : 0000:01:13.0
00010000-000100ff : sym53c8xx
00010100-0001017f : 0000:01:14.0
00010100-0001017f : tulip
00020000-0002ffff : Cujo I/O Port
howlin:~# cat /proc/interrupts/
cat: /proc/interrupts/: Not a directory
howlin:~# cat /proc/interrupts
CPU00 CPU01
32: 125984 124641 PARISC-CPU timer
33: 8458 9035 PARISC-CPU IPI
34: 120 0 PARISC-CPU lasi
35: 0 1274 PARISC-CPU Cujo
36: 7095 0 PARISC-CPU Dino [8/4]
37: 0 0 PARISC-CPU Cujo
69: 41 0 Lasi GSC PS2 keyboard, GSC PS2 mouse
86: 79 0 Lasi lasi700
99: 0 858 Cujo eth0
106: 0 417 Cujo serial
131: 7095 0 Dino [8/4] sym53c8xx
howlin:~# dmesg
Linux version 2.6.8-2-32-smp (root@palinux) (gcc version 3.3.5 (Debian
1:3.3.5-1
3)) #1 SMP Wed Aug 24 17:55:41 UTC 2005
FP[0] enabled: Rev 0 Model 14
The 32-bit Kernel has started...
Determining PDC firmware type: System Map.
model 00005b50 00000491 00000000 00000002 7754d34a 100000f0 00000008
000000b2 00
0000b2
vers 00000501
CPUID vers 14 rev 23 (0x000001d7)
capabilities 0x2
model 9000/782/J2240
Total Memory: 2048 Mb
initrd: 4fb30000-4ffee000
initrd: reserving 3fb30000-3ffee000 (mem_max 80000000) On node 0 totalpages:
524288
DMA zone: 524288 pages, LIFO batch:16
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
LCD display at f0190000,f0190001 registered
SMP: bootstrap CPU ID is 0
Built 1 zonelists
Kernel command line: root=/dev/sda5 HOME=/ console=tty0 sti=10/4/0/0
sti_font=VG
A8x16 TERM=linux palo_kernel=2/vmlinux
PID hash table entries: 16 (order 4: 128 bytes)
Console: colour dummy device 160x64
Dentry cache hash table entries: 524288 (order: 9, 2097152 bytes)
Inode-cache hash table entries: 262144 (order: 8, 1048576 bytes)
Memory: 2097152k available
Calibrating delay loop... 470.22 BogoMIPS Security Scaffold v1.0.0
initialized Capability LSM initialized Mount-cache hash table entries: 512
(order: 0, 4096 bytes) Brought up 1 CPUs
CPU0: online
domain 0: span ffffffff
groups: 00000001 00000002 00000004 00000008 00000010 00000020 00000040
0000008 0 00000100 00000200 00000400 00000800 00001000 00002000 00004000
00008000 000100 00 00020000 00040000 00080000 00100000 00200000 00400000
00800000 01000000 02000 000 04000000 08000000 10000000 20000000 40000000
80000000
CPU1: offline
domain 0: span ffffffff
groups: 00000002 00000004 00000008 00000010 00000020 00000040 00000080
0000010 0 00000200 00000400 00000800 00001000 00002000 00004000 00008000
00010000 000200 00 00040000 00080000 00100000 00200000 00400000 00800000
01000000 02000000 04000 000 08000000 10000000 20000000 40000000 80000000
00000001
CPU2: offline
domain 0: span ffffffff
groups: 00000004 00000008 00000010 00000020 00000040 00000080 00000100
0000020 0 00000400 00000800 00001000 00002000 00004000 00008000 00010000
00020000 000400 00 00080000 00100000 00200000 00400000 00800000 01000000
02000000 04000000 08000 000 10000000 20000000 40000000 80000000 00000001
00000002
CPU3: offline
domain 0: span ffffffff
groups: 00000008 00000010 00000020 00000040 00000080 00000100 00000200
0000040 0 00000800 00001000 00002000 00004000 00008000 00010000 00020000
00040000 000800 00 00100000 00200000 00400000 00800000 01000000 02000000
04000000 08000000 10000 000 20000000 40000000 80000000 00000001 00000002
00000004
CPU4: offline
domain 0: span ffffffff
groups: 00000010 00000020 00000040 00000080 00000100 00000200 00000400
0000080 0 00001000 00002000 00004000 00008000 00010000 00020000 00040000
00080000 001000 00 00200000 00400000 00800000 01000000 02000000 04000000
08000000 10000000 20000 000 40000000 80000000 00000001 00000002 00000004
00000008
CPU5: offline
domain 0: span ffffffff
groups: 00000020 00000040 00000080 00000100 00000200 00000400 00000800
0000100 0 00002000 00004000 00008000 00010000 00020000 00040000 00080000
00100000 002000 00 00400000 00800000 01000000 02000000 04000000 08000000
10000000 20000000 40000 000 80000000 00000001 00000002 00000004 00000008
00000010
CPU6: offline
domain 0: span ffffffff
groups: 00000040 00000080 00000100 00000200 00000400 00000800 00001000
0000200 0 00004000 00008000 00010000 00020000 00040000 00080000 00100000
00200000 004000 00 00800000 01000000 02000000 04000000 08000000 10000000
20000000 40000000 80000 000 00000001 00000002 00000004 00000008 00000010
00000020
CPU7: offline
domain 0: span ffffffff
groups: 00000080 00000100 00000200 00000400 00000800 00001000 00002000
0000400 0 00008000 00010000 00020000 00040000 00080000 00100000 00200000
00400000 008000 00 01000000 02000000 04000000 08000000 10000000 20000000
40000000 80000000 00000
001 00000002 00000004 00000008 00000010 00000020 00000040
CPU8: offline
domain 0: span ffffffff
groups: 00000100 00000200 00000400 00000800 00001000 00002000 00004000
0000800 0 00010000 00020000 00040000 00080000 00100000 00200000 00400000
00800000 010000 00 02000000 04000000 08000000 10000000 20000000 40000000
80000000 00000001 00000
002 00000004 00000008 00000010 00000020 00000040 00000080
CPU9: offline
domain 0: span ffffffff
groups: 00000200 00000400 00000800 00001000 00002000 00004000 00008000
0001000 0 00020000 00040000 00080000 00100000 00200000 00400000 00800000
01000000 020000 00 04000000 08000000 10000000 20000000 40000000 80000000
00000001 00000002 00000
004 00000008 00000010 00000020 00000040 00000080 00000100
CPU10: offline
domain 0: span ffffffff
groups: 00000400 00000800 00001000 00002000 00004000 00008000 00010000
0002000 0 00040000 00080000 00100000 00200000 00400000 00800000 01000000
02000000 040000 00 08000000 10000000 20000000 40000000 80000000 00000001
00000002 00000004 00000
008 00000010 00000020 00000040 00000080 00000100 00000200
CPU11: offline
domain 0: span ffffffff
groups: 00000800 00001000 00002000 00004000 00008000 00010000 00020000
0004000 0 00080000 00100000 00200000 00400000 00800000 01000000 02000000
04000000 080000 00 10000000 20000000 40000000 80000000 00000001 00000002
00000004 00000008 00000 010 00000020 00000040 00000080 00000100 00000200
00000400
CPU12: offline
domain 0: span ffffffff
groups: 00001000 00002000 00004000 00008000 00010000 00020000 00040000
0008000 0 00100000 00200000 00400000 00800000 01000000 02000000 04000000
08000000 100000 00 20000000 40000000 80000000 00000001 00000002 00000004
00000008 00000010 00000 020 00000040 00000080 00000100 00000200 00000400
00000800
CPU13: offline
domain 0: span ffffffff
groups: 00002000 00004000 00008000 00010000 00020000 00040000 00080000
0010000 0 00200000 00400000 00800000 01000000 02000000 04000000 08000000
10000000 200000 00 40000000 80000000 00000001 00000002 00000004 00000008
00000010 00000020 00000 040 00000080 00000100 00000200 00000400 00000800
00001000
CPU14: offline
domain 0: span ffffffff
groups: 00004000 00008000 00010000 00020000 00040000 00080000 00100000
0020000 0 00400000 00800000 01000000 02000000 04000000 08000000 10000000
20000000 400000 00 80000000 00000001 00000002 00000004 00000008 00000010
00000020 00000040 00000 080 00000100 00000200 00000400 00000800 00001000
00002000
CPU15: offline
domain 0: span ffffffff
groups: 00008000 00010000 00020000 00040000 00080000 00100000 00200000
0040000 0 00800000 01000000 02000000 04000000 08000000 10000000 20000000
40000000 800000 00 00000001 00000002 00000004 00000008 00000010 00000020
00000040 00000080 00000 100 00000200 00000400 00000800 00001000 00002000
00004000
CPU16: offline
domain 0: span ffffffff
groups: 00010000 00020000 00040000 00080000 00100000 00200000 00400000
0080000 0 01000000 02000000 04000000 08000000 10000000 20000000 40000000
80000000 000000
01 00000002 00000004 00000008 00000010 00000020 00000040 00000080 00000100
00000 200 00000400 00000800 00001000 00002000 00004000 00008000
CPU17: offline
domain 0: span ffffffff
groups: 00020000 00040000 00080000 00100000 00200000 00400000 00800000
0100000 0 02000000 04000000 08000000 10000000 20000000 40000000 80000000
00000001 000000
02 00000004 00000008 00000010 00000020 00000040 00000080 00000100 00000200
00000 400 00000800 00001000 00002000 00004000 00008000 00010000
CPU18: offline
domain 0: span ffffffff
groups: 00040000 00080000 00100000 00200000 00400000 00800000 01000000
0200000 0 04000000 08000000 10000000 20000000 40000000 80000000 00000001
00000002 000000
04 00000008 00000010 00000020 00000040 00000080 00000100 00000200 00000400
00000 800 00001000 00002000 00004000 00008000 00010000 00020000
CPU19: offline
domain 0: span ffffffff
groups: 00080000 00100000 00200000 00400000 00800000 01000000 02000000
0400000 0 08000000 10000000 20000000 40000000 80000000 00000001 00000002
00000004 000000
08 00000010 00000020 00000040 00000080 00000100 00000200 00000400 00000800
00001 000 00002000 00004000 00008000 00010000 00020000 00040000
CPU20: offline
domain 0: span ffffffff
groups: 00100000 00200000 00400000 00800000 01000000 02000000 04000000
0800000 0 10000000 20000000 40000000 80000000 00000001 00000002 00000004
00000008 000000 10 00000020 00000040 00000080 00000100 00000200 00000400
00000800 00001000 00002 000 00004000 00008000 00010000 00020000 00040000
00080000
CPU21: offline
domain 0: span ffffffff
groups: 00200000 00400000 00800000 01000000 02000000 04000000 08000000
1000000 0 20000000 40000000 80000000 00000001 00000002 00000004 00000008
00000010 000000 20 00000040 00000080 00000100 00000200 00000400 00000800
00001000 00002000 00004 000 00008000 00010000 00020000 00040000 00080000
00100000
CPU22: offline
domain 0: span ffffffff
groups: 00400000 00800000 01000000 02000000 04000000 08000000 10000000
2000000 0 40000000 80000000 00000001 00000002 00000004 00000008 00000010
00000020 000000 40 00000080 00000100 00000200 00000400 00000800 00001000
00002000 00004000 00008 000 00010000 00020000 00040000 00080000 00100000
00200000
CPU23: offline
domain 0: span ffffffff
groups: 00800000 01000000 02000000 04000000 08000000 10000000 20000000
4000000 0 80000000 00000001 00000002 00000004 00000008 00000010 00000020
00000040 000000 80 00000100 00000200 00000400 00000800 00001000 00002000
00004000 00008000 00010 000 00020000 00040000 00080000 00100000 00200000
00400000
CPU24: offline
domain 0: span ffffffff
groups: 01000000 02000000 04000000 08000000 10000000 20000000 40000000
8000000 0 00000001 00000002 00000004 00000008 00000010 00000020 00000040
00000080 000001 00 00000200 00000400 00000800 00001000 00002000 00004000
00008000 00010000 00020 000 00040000 00080000 00100000 00200000 00400000
00800000
CPU25: offline
domain 0: span ffffffff
groups: 02000000 04000000 08000000 10000000 20000000 40000000 80000000
0000000
1 00000002 00000004 00000008 00000010 00000020 00000040 00000080 00000100
000002 00 00000400 00000800 00001000 00002000 00004000 00008000 00010000
00020000 00040 000 00080000 00100000 00200000 00400000 00800000 01000000
CPU26: offline
domain 0: span ffffffff
groups: 04000000 08000000 10000000 20000000 40000000 80000000 00000001
0000000
2 00000004 00000008 00000010 00000020 00000040 00000080 00000100 00000200
000004 00 00000800 00001000 00002000 00004000 00008000 00010000 00020000
00040000 00080 000 00100000 00200000 00400000 00800000 01000000 02000000
CPU27: offline
domain 0: span ffffffff
groups: 08000000 10000000 20000000 40000000 80000000 00000001 00000002
0000000
4 00000008 00000010 00000020 00000040 00000080 00000100 00000200 00000400
000008 00 00001000 00002000 00004000 00008000 00010000 00020000 00040000
00080000 00100 000 00200000 00400000 00800000 01000000 02000000 04000000
CPU28: offline
domain 0: span ffffffff
groups: 10000000 20000000 40000000 80000000 00000001 00000002 00000004
0000000
8 00000010 00000020 00000040 00000080 00000100 00000200 00000400 00000800
000010 00 00002000 00004000 00008000 00010000 00020000 00040000 00080000
00100000 00200 000 00400000 00800000 01000000 02000000 04000000 08000000
CPU29: offline
domain 0: span ffffffff
groups: 20000000 40000000 80000000 00000001 00000002 00000004 00000008
0000001 0 00000020 00000040 00000080 00000100 00000200 00000400 00000800
00001000 000020 00 00004000 00008000 00010000 00020000 00040000 00080000
00100000 00200000 00400 000 00800000 01000000 02000000 04000000 08000000
10000000
CPU30: offline
domain 0: span ffffffff
groups: 40000000 80000000 00000001 00000002 00000004 00000008 00000010
0000002 0 00000040 00000080 00000100 00000200 00000400 00000800 00001000
00002000 000040 00 00008000 00010000 00020000 00040000 00080000 00100000
00200000 00400000 00800 000 01000000 02000000 04000000 08000000 10000000
20000000
CPU31: offline
domain 0: span ffffffff
groups: 80000000 00000001 00000002 00000004 00000008 00000010 00000020
0000004 0 00000080 00000100 00000200 00000400 00000800 00001000 00002000
00004000 000080 00 00010000 00020000 00040000 00080000 00100000 00200000
00400000 00800000 01000 000 02000000 04000000 08000000 10000000 20000000
40000000 checking if image is initramfs...it isn't (ungzip failed); looks
like an initrd
NET: Registered protocol family 16
EISA bus registered
Searching for devices...
Found devices:
1. U2-IOA BC Runway Port at 0xfff88000 [8] { 12, 0xf, 0x580, 0x0000b } 2.
unknown device at 0xfc000000 [8/0] { 13, 0x3, 0x05d, 0x0000a }, additional
a
ddresses: 0xfd800000
3. SummitHawk Dino RS-232 at 0xfc003000 [8/0/63] { 10, 0x0, 0x05d, 0x0008c }
4. Dino PCI Bridge at 0xfc004000 [8/4] { 13, 0x3, 0x680, 0x0000a },
additional
addresses: 0xfc800000
5. SummitHawk 230 Core BA at 0xffd00000 [8/12] { 11, 0x0, 0x05c, 0x00081 },
add itional addresses: 0xffd0c000 0xffc00000 6. SummitHawk 230 Core
Centronics at 0xffd02000 [8/12/0] { 10, 0x0, 0x05c, 0x000
74 }, additional addresses: 0xffd01000 0xffd03000 7. SummitHawk 230 Core
Audio at 0xffd04000 [8/12/1] { 10, 0x4, 0x05c, 0x0007b } 8. SummitHawk 230
Core SCSI at 0xffd06000 [8/12/5] { 10, 0x0, 0x05c, 0x00082 } 9. SummitHawk
230 Core PS/2 Port at 0xffd08000 [8/12/7] { 10, 0x0, 0x05c, 0x0008
4 }
10. SummitHawk 230 Core PS/2 Port at 0xffd08100 [8/12/8] { 10, 0x0, 0x05c,
0x000
84 }
11. U2-IOA BC GSC+ Port at 0xfc03f000 [8/63] { 7, 0x1, 0x501, 0x0000c } 12.
U2-IOA BC Runway Port at 0xfff8a000 [10] { 12, 0xf, 0x580, 0x0000b } 13.
Cujo PCI Bridge at 0xf1604000 [10/4] { 13, 0x1, 0x682, 0x0000a }, additiona
l addresses: 0xf1800000 0xf6000000 14. SummitHawk Dino RS-232 at 0xf1607000
[10/4/63] { 10, 0x0, 0x05d, 0x0008c } 15. U2-IOA BC GSC+ Port at 0xf163f000
[10/63] { 7, 0x1, 0x501, 0x0000c } 16. SummitHawk U+ at 0xfffa0000 [32] { 0,
0x0, 0x5b5, 0x00004 } 17. SummitHawk U+ at 0xfffa2000 [34] { 0, 0x0, 0x5b5,
0x00004 } 18. Memory at 0xfffb1000 [49] { 1, 0x0, 0x083, 0x00009 } Releasing
cpu 1 now, hpa=fffa2000 FP[1] enabled: Rev 0 Model 14
CPU(s): 2 x PA8200 (PCX-U+) at 236.000000 MHz Found U2 at 0xfff88000 Found
U2 at 0xfff8a000 Lasi version 0 at 0xffd00000 found.
Cujo version unknown found at 0xfc000000 Dino [8/4] version 3.1 found at
0xfc004000 Cujo version 2.0 found at 0xf1604000 Enabling Cujo 2.0 bug
workaround SCSI subsystem initialized TC classifier action (bugs to
netdev@oss.sgi.com cc hadi@cyberus.ca) STI GSC/PCI core graphics driver
Version 0.9a STI PCI graphic ROM found at f1ff0000 (64 kB), fb at f6000000
(32 MB)
id 2d08c0a7-9a02587, conforms to spec rev. 8.0a
graphics card name: PCI_GRAFFITIX1280
fb0: stifb 1280x1024-8 frame buffer device, PCI_GRAFFITIX1280, id: 2d08c0a7,
mmi
o: 0xf6100000
unwind_init: start = 0x103b6720, end = 0x103d7f40, entries = 8578
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Soft power switch enabled, polling @ 0xf0140000.
Console: switching to colour frame buffer device 160x64 Generic RTC Driver
v1.07
Serial: 8250/16550 driver $Revision: 1.90 $ 25 ports, IRQ sharing enabled
ttyS0 at MMIO 0xfc003800 (irq = 106) is a 16550A
ttyS1 at MMIO 0xf1607800 (irq = 170) is a 16550A RAMDISK driver initialized:
16 RAM disks of 8192K size 1024 blocksize
mice: PS/2 mouse device common for all mice
serio: GSC PS2 keyboard port at 0xffd08000 irq 69 @ parisc8:12:7
input: AT Raw Set 2 keyboard on parisc8:12:7
serio: GSC PS2 mouse port at 0xffd08100 irq 69 @ parisc8:12:8 HP SDC: No SDC
found.
HP SDC MLC: Registering the System Domain Controller's HIL MLC.
HP SDC MLC: Request for raw HIL ISR hook denied
NET: Registered protocol family 2
IP: routing cache hash table of 4096 buckets, 96Kbytes
TCP: Hash tables configured (established 131072 bind 52428)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4856 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: Badness in smp_call_function at
arch/parisc/kernel
/smp.c:342
Backtrace:
[<1011963c>] smp_call_function+0x408/0x410 [<101088fc>]
flush_data_cache+0x24/0x40 [<10107a58>] free_initmem+0x78/0x38c
[<10103d30>] init+0x304/0x410 [<10110c5c>] ret_from_kernel_thread+0x1c/0x24
344k freed
NET: Registered protocol family 1
sym0: <895> rev 0x1 at pci 0000:01:13.0 irq 131
sym0: No NVRAM, ID 7, Fast-40, SE, parity checking
sym0: SCSI BUS has been reset.
sym0: SCSI BUS mode change from SE to SE.
sym0: SCSI BUS has been reset.
scsi0 : sym-2.1.18k
Using anticipatory io scheduler
Vendor: IBM Model: DDRS-39130WS Rev: HP01
Type: Direct-Access ANSI SCSI revision: 02
sym0:5:0: tagged command queuing enabled, command queue depth 16.
scsi(0:0:5:0): Beginning Domain Validation
sym0:5: wide asynchronous.
sym0:5: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15)
scsi(0:0:5:0): Domain Validation skipping write tests
scsi(0:0:5:0): Ending Domain Validation
Vendor: IBM Model: DDRS-39130WS Rev: HP01
Type: Direct-Access ANSI SCSI revision: 02
sym0:6:0: tagged command queuing enabled, command queue depth 16.
scsi(0:0:6:0): Beginning Domain Validation
sym0:6: wide asynchronous.
sym0:6: FAST-20 WIDE SCSI 40.0 MB/s ST (50.0 ns, offset 15)
scsi(0:0:6:0): Domain Validation skipping write tests
scsi(0:0:6:0): Ending Domain Validation
53c700: Version 2.8 By James.Bottomley@HansenPartnership.com
scsi1: 53c710 rev 2
scsi1 : LASI SCSI 53c700
Vendor: TOSHIBA Model: CD-ROM XM-5701TA Rev: 1557
Type: CD-ROM ANSI SCSI revision: 02
scsi(1:0:2:0): Beginning Domain Validation
scsi1: (2:0) Asynchronous
scsi1: (2:0) Synchronous at offset 8, period 100ns
scsi(1:0:2:0): Domain Validation skipping write tests
scsi(1:0:2:0): Ending Domain Validation
Vendor: HP Model: C1537A Rev: HP02
Type: Sequential-Access ANSI SCSI revision: 02
scsi(1:0:3:0): Beginning Domain Validation
scsi1: (3:0) Asynchronous
scsi1: (3:0) Synchronous at offset 8, period 100ns
scsi(1:0:3:0): Domain Validation skipping write tests
scsi(1:0:3:0): Ending Domain Validation
usbcore: registered new driver hub
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver Linux Tulip driver
version 1.1.13 (May 11, 2002)
tulip0: EEPROM default media type Autosense.
tulip0: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
tulip0: ***WARNING***: No MII transceiver found!
eth0: Digital DS21143 Tulip rev 33 at 0xfd810000, 00:60:B0:B2:FC:F5, IRQ 99.
tulip1: no phy info, aborting mtable build
tulip1: MII transceiver #1 config 1000 status 7809 advertising 01e1.
eth1: Digital DS21143 Tulip rev 48 at 0xfc802000, 00:60:B0:A4:F3:F1, IRQ
128.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sda:
drive cache: write through
/dev/scsi/host0/bus0/target5/lun0: p1 p2 p3 < p5 p6 > Attached scsi disk
sda at scsi0, channel 0, id 5, lun 0 SCSI device sdb: 17773524 512-byte hdwr
sectors (9100 MB) SCSI device sdb: drive cache: write through
/dev/scsi/host0/bus0/target6/lun0:
Attached scsi disk sdb at scsi0, channel 0, id 6, lun 0
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.20
Attached scsi CD-ROM sr0 at scsi1, channel 0, id 2, lun 0 kjournald
starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 353388k swap on /dev/sda6. Priority:-1 extents:1
EXT3 FS on sda5, internal journal
ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
USB Universal Host Controller Interface driver v2.2 Attached scsi generic
sg0 at scsi0, channel 0, id 5, lun 0, type 0 Attached scsi generic sg1 at
scsi0, channel 0, id 6, lun 0, type 0 Attached scsi generic sg2 at scsi1,
channel 0, id 2, lun 0, type 5 Attached scsi generic sg3 at scsi1, channel
0, id 3, lun 0, type 1
st: Version 20040403, fixed bufsize 32768, s/g segs 256 Attached scsi tape
st0 at scsi1, channel 0, id 3, lun 0
st0: try direct i/o: yes (alignment 512 B), max page reachable by HBA
1048575 module ipv6 relocation of symbol ipv6_chk_addr is out of range
(0x3ffefffd in 17
bits)
module ipv6 relocation of symbol ipv6_chk_addr is out of range (0x3ffefffd
in 17
bits)
dirmngr (pid 1983): Protection id trap (code 7) at 4000201f
YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
PSW: 00000000000001000000000000001111 Not tainted
r00-03 00000000 400023a0 4000201c faf00778
r04-07 40734a58 0001fd60 00000006 00000001
r08-11 00046ea8 00046ea8 000476a8 000001f6
r12-15 00000003 faf00130 00000000 00000001
r16-19 00000000 00000000 00000000 4077ada8
r20-23 00000001 4060d57c faf00778 00000000
r24-27 4077b424 00000000 4077b378 00045ea8
r28-31 00000000 ffffffff 40002308 40754083
sr0-3 00000c22 00000c22 00000000 00000c22
sr4-7 00000c22 00000c22 00000c22 00000c22
IASQ: 00000c22 00000c22 IAOQ: 4000201f 40002023
IIR: 43ffff40 ISR: 102401e9 IOR: 3fb7b660
CPU: 0 CR30: 8a538000 CR31: 10468000
ORIG_R28: 00000000
IAOQ[0]: 0x4000201f
IAOQ[1]: 0x40002023
RP(r2): 0x4000201c
parport_pc: Unknown symbol dma_spin_lock
lp: driver loaded but no devices found
NET: Registered protocol family 5
module ipv6 relocation of symbol ipv6_chk_addr is out of range (0x3ffefffd
in 17
bits)
module ipv6 relocation of symbol ipv6_chk_addr is out of range (0x3ffefffd
in 17
bits)
module ipv6 relocation of symbol ipv6_chk_addr is out of range (0x3ffefffd
in 17
bits)
-----Original Message-----
From: varenet@gmail.com [mailto:varenet@gmail.com] On Behalf Of Thibaut
VARENE
Sent: Sunday, January 01, 2006 9:16 AM
To: Grant Grundler
Cc: Craig D. Lansing; parisc-linux@lists.parisc-linux.org
Subject: Re: [parisc-linux] J2240 - Almost there....
On 1/1/06, Grant Grundler <grundler@parisc-linux.org> wrote:
> On Sat, Dec 31, 2005 at 11:21:06PM -0500, Craig D. Lansing wrote:
> > Duh!!! Can you tell that it has been a long time since I've had a
"real"
> > computer to play with?
> >
> > Anyway, I now have a dual-boot (HP-UX 10 / Debian Linux) J2240.
> >
> > Here's what SAM thinks is in the system:
>
> "ioscan -fk" is the preferred output and I can
> better understand what is in the box.
> I don't understand what's really built-in or add-on
> with the SAM output.
And while you're at it, i'd love to have the output of 'cat
/proc/cpuinfo' 'cat /proc/iomem' 'cat /proc/ioports' 'cat
/proc/interrupts/' and 'dmesg' from Linux to add to this growing list
:
http://www.pateam.org/archive/logs/ ;)
Thx and happy new year to every one!
T-Bone
--
Thibaut VARENE
http://www.parisc-linux.org/~varenet/
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* RE: [parisc-linux] J2240 - Almost there....
2006-01-01 6:32 ` Grant Grundler
2006-01-01 14:15 ` Thibaut VARENE
@ 2006-01-03 2:01 ` Craig D. Lansing
1 sibling, 0 replies; 25+ messages in thread
From: Craig D. Lansing @ 2006-01-03 2:01 UTC (permalink / raw)
To: 'Grant Grundler'; +Cc: parisc-linux
I finally got the getty to work on HP-UX. Here's the ioscan -fk output:
Class I H/W Path Driver S/W State H/W Type
Description
============================================================================
==
bc 0 root CLAIMED BUS_NEXUS
bc 1 8 ccio CLAIMED BUS_NEXUS I/O
Adapter
ba 0 8/0 GSCtoPCI CLAIMED BUS_NEXUS PCI Bus
Bridge
- GSCtoPCI
unknown -1 8/0/3/0 UNCLAIMED UNKNOWN
PCI(10110019)
-- 3
lan 1 8/0/4/0 fddi4 CLAIMED INTERFACE PCI FDDI
Adapt
er
tty 0 8/0/63 asio0 CLAIMED INTERFACE Built-in
RS-23
2C
ba 1 8/4 GSCtoPCI CLAIMED BUS_NEXUS PCI Bus
Bridge
- GSCtoPCI
ext_bus 0 8/4/19/0 c720 CLAIMED INTERFACE Ultra2
Wide SC
SI
target 0 8/4/19/0.5 tgt CLAIMED DEVICE
disk 0 8/4/19/0.5.0 sdisk CLAIMED DEVICE IBM
DDRS-3
9130WS
target 1 8/4/19/0.6 tgt CLAIMED DEVICE
disk 1 8/4/19/0.6.0 sdisk CLAIMED DEVICE IBM
DDRS-3
9130WS
target 2 8/4/19/0.7 tgt CLAIMED DEVICE
ctl 0 8/4/19/0.7.0 sctl CLAIMED DEVICE Initiator
lan 0 8/4/20/0 btlan3 CLAIMED INTERFACE
PCI(10110019)
-- Built-in #2
ba 2 8/12 bus_adapter CLAIMED BUS_NEXUS Core I/O
Adapt
er
ext_bus 2 8/12/0 CentIf CLAIMED INTERFACE Built-in
Paral
lel Interface
audio 0 8/12/1 audio CLAIMED INTERFACE Built-in
Audio
ext_bus 1 8/12/5 c720 CLAIMED INTERFACE Built-in
SCSI
target 3 8/12/5.2 tgt CLAIMED DEVICE
disk 2 8/12/5.2.0 sdisk CLAIMED DEVICE TOSHIBA
CD-ROM
XM-5701TA
target 4 8/12/5.3 tgt CLAIMED DEVICE
tape 0 8/12/5.3.0 stape CLAIMED DEVICE HP
C1537A
target 5 8/12/5.7 tgt CLAIMED DEVICE
ctl 1 8/12/5.7.0 sctl CLAIMED DEVICE Initiator
ps2 0 8/12/7 ps2 CLAIMED INTERFACE Built-in
Keybo
ard/Mouse
bc 2 10 ccio CLAIMED BUS_NEXUS I/O
Adapter
ba 3 10/4 GSCtoPCI CLAIMED BUS_NEXUS PCI Bus
Bridge
- GSCtoPCI
graphics 0 10/4/0/0 graph3 CLAIMED INTERFACE
PCI(103c1005)
-- 0
tty 1 10/4/63 asio0 CLAIMED INTERFACE Built-in
RS-23
2C
processor 0 32 processor CLAIMED PROCESSOR Processor
processor 1 34 processor CLAIMED PROCESSOR Processor
memory 0 49 memory CLAIMED MEMORY Memory
-----Original Message-----
From: Grant Grundler [mailto:grundler@parisc-linux.org]
Sent: Sunday, January 01, 2006 1:33 AM
To: Craig D. Lansing
Cc: parisc-linux@lists.parisc-linux.org
Subject: Re: [parisc-linux] J2240 - Almost there....
On Sat, Dec 31, 2005 at 11:21:06PM -0500, Craig D. Lansing wrote:
> Duh!!! Can you tell that it has been a long time since I've had a "real"
> computer to play with?
>
> Anyway, I now have a dual-boot (HP-UX 10 / Debian Linux) J2240.
>
> Here's what SAM thinks is in the system:
"ioscan -fk" is the preferred output and I can
better understand what is in the box.
I don't understand what's really built-in or add-on
with the SAM output.
thanks,
grant
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost there....
2006-01-03 1:19 ` Craig D. Lansing
@ 2006-01-03 2:01 ` Matthew Wilcox
2006-01-04 17:43 ` Grant Grundler
1 sibling, 0 replies; 25+ messages in thread
From: Matthew Wilcox @ 2006-01-03 2:01 UTC (permalink / raw)
To: Craig D. Lansing; +Cc: parisc-linux, 'Thibaut VARENE'
On Mon, Jan 02, 2006 at 08:19:55PM -0500, Craig D. Lansing wrote:
> f1600000-f3ffffff : GSC Bus [10/]
> f1604000-f1604fff : Cujo
> f1607800-f1607807 : serial
> f1800000-f1ffffff : Cujo LMMIO 0
> f4000000-f5ffffff : GSC Bus [8/]
> f6000000-f7ffffff : GSC Bus [10/]
> f6000000-f7ffffff : Cujo LMMIO 1
> f8000000-fff7ffff : GSC Bus [8/]
> fc000000-fc000fff : Cujo
> fc004000-fc004fff : Dino [8/4]
> fc800000-fcffffff : Dino [8/4] LMMIO 0
> fd800000-fdffffff : Cujo LMMIO 0
[...]
> Found devices:
> 1. U2-IOA BC Runway Port at 0xfff88000 [8] { 12, 0xf, 0x580, 0x0000b } 2.
> unknown device at 0xfc000000 [8/0] { 13, 0x3, 0x05d, 0x0000a }, additional
> a
> ddresses: 0xfd800000
[...]
> Cujo version unknown found at 0xfc000000 Dino [8/4] version 3.1 found at
> 0xfc004000 Cujo version 2.0 found at 0xf1604000 Enabling Cujo 2.0 bug
> workaround SCSI subsystem initialized TC classifier action (bugs to
Fixed both of these problems (Dino reported as Cujo and first Cujo
reported as unknown)
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost there....
2006-01-03 1:19 ` Craig D. Lansing
2006-01-03 2:01 ` Matthew Wilcox
@ 2006-01-04 17:43 ` Grant Grundler
2006-01-04 17:49 ` Matthew Wilcox
1 sibling, 1 reply; 25+ messages in thread
From: Grant Grundler @ 2006-01-04 17:43 UTC (permalink / raw)
To: Craig D. Lansing; +Cc: parisc-linux
On Mon, Jan 02, 2006 at 08:19:55PM -0500, Craig D. Lansing wrote:
> Sorry that it took so long to reply. I spent most of the day driving to /
> from Washington, DC yesterday. Re-installed and ran into problems as
> follows:
>
> 1) Got gdm prompt (black&white, really large), but was able to login. Mouse
> was not recognized after that so I was "stuck" in the desktop.
ctl-alt-backspace will kill the X11 server.
> I was able to login OK in single user command line mode.
>
> 2) Re-installed after getting the actual "advanced" HP p1120 console specs
> (instead of "simple"). Re-install failed due to "SMP CALL FUNCTION TIMED
> OUT! (cpu=0), try ###" errors (I powered off the box after about 2000 of
> these).
Newer kernels (not sure if 2.6.14, but certainly 2.6.15-pa1) fix this.
(kudos to James Bottomley)
> Rebooted and got message to run "dpkg --configure -a". Did that
> and packages installed. The system now tries to start gdm (flickers a lot),
> but ultimately just goes to a blinking cursor When I reboot (shutdown -r 0)
> I now get the "Welcome to your new Debian system" prompt. I guess maybe I
> should re-install again????
>
> 3) Networking appears to not be working, I assumed that is because of the
> "blacklisted" FDDI card (defxx,DEFPA).
Unlikely.
> The box has an internal IP address
> 192.168.1.100 and I can't even ping it. However, I cannot ping the box when
> booted into HP-UX either (192.168.1.200). Bad card (I tried the obvious of
> another cable)????
Add a 100BT card (tulip or e100) and see if that works better.
According to HW DB, j2240 has DEC21143 (tulip) built-in and I would
expect that to work fine.
Based on the /proc/iomem output below, looks like you have two tulip
devices in the machine. Likely the LAN cable is connected to the wrong one.
> To get the info. requsted below w/o a LAN, I "cheated" and started a getty
> against a serial port, logged in via a Reflection session, and logged to an
> output file... not pretty, but functional. Sorry if this is more than you
> wanted to see.
no problem.
...
> howlin:~# cat /proc/iomem
> 00000000-7fffffff : System RAM
> 00000000-000009ff : PDC data (Page Zero)
> 00100000-003b4fff : Kernel code
> 003b5000-00513b03 : Kernel data
> f0190000-f0190000 : lcd_cmd
> f0190001-f0190001 : lcd_data
> f1600000-f3ffffff : GSC Bus [10/]
> f1604000-f1604fff : Cujo
> f1607800-f1607807 : serial
> f1800000-f1ffffff : Cujo LMMIO 0
> f4000000-f5ffffff : GSC Bus [8/]
> f6000000-f7ffffff : GSC Bus [10/]
> f6000000-f7ffffff : Cujo LMMIO 1
> f6000000-f7ffffff : 0000:02:00.0
> f6100000-f64fffff : stifb mmio
> f7000000-f71fffff : stifb fb
> f8000000-fff7ffff : GSC Bus [8/]
> fc000000-fc000fff : Cujo
> fc003800-fc003807 : serial
> fc004000-fc004fff : Dino [8/4]
> fc800000-fcffffff : Dino [8/4] LMMIO 0
> fc800000-fc800fff : 0000:01:13.0
> fc800000-fc800fff : sym53c8xx
> fc801000-fc8010ff : 0000:01:13.0
> fc801000-fc8010ff : sym53c8xx
> fc802000-fc80207f : 0000:01:14.0
> fc802000-fc80207f : tulip
> fd800000-fdffffff : Cujo LMMIO 0
> fd800000-fd80ffff : 0000:00:04.0
> fd810000-fd81007f : 0000:00:03.0
> fd810000-fd81007f : tulip
> fd811000-fd81107f : 0000:00:04.0
> ffd00000-ffdfffff : Lasi
> ffd00000-ffd00fff : Lasi
> ffd06000-ffd06fff : Lasi SCSI
> ffd08000-ffd08fff : GSC PS2
> fff80000-fffaffff : Central Bus
> fff88000-fff88fff : U2:Uturn
> fff8a000-fff8afff : U2:Uturn
> fffa0000-fffa0fff : CPU
> fffa2000-fffa2fff : CPU
> fffb0000-fffdffff : Local Broadcast
> fffe0000-ffffffff : Global Broadcast
0000:00:03.0 is tulip in slot 3.
0000:01:14.0 is tulip built-in. (my guess)
> howlin:~# cat /proc/interrupts
> CPU00 CPU01
> 32: 125984 124641 PARISC-CPU timer
> 33: 8458 9035 PARISC-CPU IPI
> 34: 120 0 PARISC-CPU lasi
> 35: 0 1274 PARISC-CPU Cujo
> 36: 7095 0 PARISC-CPU Dino [8/4]
> 37: 0 0 PARISC-CPU Cujo
> 69: 41 0 Lasi GSC PS2 keyboard, GSC PS2 mouse
> 86: 79 0 Lasi lasi700
> 99: 0 858 Cujo eth0
Note that eth0 is routed to Cujo (not dino) - this tulip is in slot 3.
> 106: 0 417 Cujo serial
> 131: 7095 0 Dino [8/4] sym53c8xx
> howlin:~# dmesg
> Linux version 2.6.8-2-32-smp (root@palinux) (gcc version 3.3.5 (Debian
> 1:3.3.5-1
> 3)) #1 SMP Wed Aug 24 17:55:41 UTC 2005
> FP[0] enabled: Rev 0 Model 14
> The 32-bit Kernel has started...
> Determining PDC firmware type: System Map.
...
> Brought up 1 CPUs
> CPU0: online
> domain 0: span ffffffff
> groups: 00000001 00000002 00000004 00000008 00000010 00000020 00000040
> 0000008 0 00000100 00000200 00000400 00000800 00001000 00002000 00004000
> 00008000 000100 00 00020000 00040000 00080000 00100000 00200000 00400000
> 00800000 01000000 02000 000 04000000 08000000 10000000 20000000 40000000
> 80000000
> CPU1: offline
> domain 0: span ffffffff
> groups: 00000002 00000004 00000008 00000010 00000020 00000040 00000080
> 0000010 0 00000200 00000400 00000800 00001000 00002000 00004000 00008000
> 00010000 000200 00 00040000 00080000 00100000 00200000 00400000 00800000
> 01000000 02000000 04000 000 08000000 10000000 20000000 40000000 80000000
> 00000001
> CPU2: offline
> domain 0: span ffffffff
> groups: 00000004 00000008 00000010 00000020 00000040 00000080 00000100
> 0000020 0 00000400 00000800 00001000 00002000 00004000 00008000 00010000
> 00020000 000400 00 00080000 00100000 00200000 00400000 00800000 01000000
> 02000000 04000000 08000 000 10000000 20000000 40000000 80000000 00000001
> 00000002
...
> CPU31: offline
> domain 0: span ffffffff
> groups: 80000000 00000001 00000002 00000004 00000008 00000010 00000020
> 0000004 0 00000080 00000100 00000200 00000400 00000800 00001000 00002000
> 00004000 000080 00 00010000 00020000 00040000 00080000 00100000 00200000
> 00400000 00800000 01000 000 02000000 04000000 08000000 10000000 20000000
> 40000000
Do we really need this stuff dumped to console?
> 0x00004 } 18. Memory at 0xfffb1000 [49] { 1, 0x0, 0x083, 0x00009 } Releasing
> cpu 1 now, hpa=fffa2000 FP[1] enabled: Rev 0 Model 14
> CPU(s): 2 x PA8200 (PCX-U+) at 236.000000 MHz Found U2 at 0xfff88000 Found
> U2 at 0xfff8a000 Lasi version 0 at 0xffd00000 found.
> Cujo version unknown found at 0xfc000000 Dino [8/4] version 3.1 found at
> 0xfc004000 Cujo version 2.0 found at 0xf1604000 Enabling Cujo 2.0 bug
> workaround SCSI subsystem initialized TC classifier action (bugs to
> netdev@oss.sgi.com cc hadi@cyberus.ca) STI GSC/PCI core graphics driver
> Version 0.9a STI PCI graphic ROM found at f1ff0000 (64 kB), fb at f6000000
> (32 MB)
Your mailer or capture utility is loosing CRs here.
> version 1.1.13 (May 11, 2002)
> tulip0: EEPROM default media type Autosense.
> tulip0: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
> tulip0: ***WARNING***: No MII transceiver found!
> eth0: Digital DS21143 Tulip rev 33 at 0xfd810000, 00:60:B0:B2:FC:F5, IRQ 99.
> tulip1: no phy info, aborting mtable build
> tulip1: MII transceiver #1 config 1000 status 7809 advertising 01e1.
> eth1: Digital DS21143 Tulip rev 48 at 0xfc802000, 00:60:B0:A4:F3:F1, IRQ
> 128.
...
ok. should be easy now to figure out which is connected (or not).
thanks,
grant
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost there....
2006-01-04 17:43 ` Grant Grundler
@ 2006-01-04 17:49 ` Matthew Wilcox
2006-01-04 18:18 ` Grant Grundler
0 siblings, 1 reply; 25+ messages in thread
From: Matthew Wilcox @ 2006-01-04 17:49 UTC (permalink / raw)
To: Grant Grundler; +Cc: parisc-linux
On Wed, Jan 04, 2006 at 10:43:32AM -0700, Grant Grundler wrote:
> ...
> > howlin:~# cat /proc/iomem
> > 00000000-7fffffff : System RAM
> > 00000000-000009ff : PDC data (Page Zero)
> > 00100000-003b4fff : Kernel code
> > 003b5000-00513b03 : Kernel data
> > f0190000-f0190000 : lcd_cmd
> > f0190001-f0190001 : lcd_data
> > f1600000-f3ffffff : GSC Bus [10/]
> > f1604000-f1604fff : Cujo
> > f1607800-f1607807 : serial
> > f1800000-f1ffffff : Cujo LMMIO 0
> > f4000000-f5ffffff : GSC Bus [8/]
> > f6000000-f7ffffff : GSC Bus [10/]
> > f6000000-f7ffffff : Cujo LMMIO 1
> > f6000000-f7ffffff : 0000:02:00.0
> > f6100000-f64fffff : stifb mmio
> > f7000000-f71fffff : stifb fb
> > f8000000-fff7ffff : GSC Bus [8/]
> > fc000000-fc000fff : Cujo
> > fc003800-fc003807 : serial
> > fc004000-fc004fff : Dino [8/4]
> > fc800000-fcffffff : Dino [8/4] LMMIO 0
> > fc800000-fc800fff : 0000:01:13.0
> > fc800000-fc800fff : sym53c8xx
> > fc801000-fc8010ff : 0000:01:13.0
> > fc801000-fc8010ff : sym53c8xx
> > fc802000-fc80207f : 0000:01:14.0
> > fc802000-fc80207f : tulip
> > fd800000-fdffffff : Cujo LMMIO 0
> > fd800000-fd80ffff : 0000:00:04.0
> > fd810000-fd81007f : 0000:00:03.0
> > fd810000-fd81007f : tulip
> > fd811000-fd81107f : 0000:00:04.0
> > ffd00000-ffdfffff : Lasi
> > ffd00000-ffd00fff : Lasi
> > ffd06000-ffd06fff : Lasi SCSI
> > ffd08000-ffd08fff : GSC PS2
> > fff80000-fffaffff : Central Bus
> > fff88000-fff88fff : U2:Uturn
> > fff8a000-fff8afff : U2:Uturn
> > fffa0000-fffa0fff : CPU
> > fffa2000-fffa2fff : CPU
> > fffb0000-fffdffff : Local Broadcast
> > fffe0000-ffffffff : Global Broadcast
>
>
> 0000:00:03.0 is tulip in slot 3.
> 0000:01:14.0 is tulip built-in. (my guess)
I disagree. The 'Cujo' on GSC bus 8 is actually a Dino. As I said
in my earlier mail, I've now fixed this. So I think eth0 (00:03.0)
is actually the built-in one.
> > CPU0: online
> > domain 0: span ffffffff
> > groups: 00000001 00000002 00000004 00000008 00000010 00000020 00000040
> > 0000008 0 00000100 00000200 00000400 00000800 00001000 00002000 00004000
> > 00008000 000100 00 00020000 00040000 00080000 00100000 00200000 00400000
> > 00800000 01000000 02000 000 04000000 08000000 10000000 20000000 40000000
> > 80000000
> > CPU1: offline
> > domain 0: span ffffffff
> > groups: 00000002 00000004 00000008 00000010 00000020 00000040 00000080
> > 0000010 0 00000200 00000400 00000800 00001000 00002000 00004000 00008000
> > 00010000 000200 00 00040000 00080000 00100000 00200000 00400000 00800000
> > 01000000 02000000 04000 000 08000000 10000000 20000000 40000000 80000000
> > 00000001
>
> Do we really need this stuff dumped to console?
I think it's no longer dumped to console by current kernels.
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* Re: [parisc-linux] J2240 - Almost there....
2006-01-04 17:49 ` Matthew Wilcox
@ 2006-01-04 18:18 ` Grant Grundler
2006-01-05 4:08 ` Craig D. Lansing
0 siblings, 1 reply; 25+ messages in thread
From: Grant Grundler @ 2006-01-04 18:18 UTC (permalink / raw)
To: Matthew Wilcox; +Cc: parisc-linux
On Wed, Jan 04, 2006 at 10:49:43AM -0700, Matthew Wilcox wrote:
...
> > 0000:00:03.0 is tulip in slot 3.
> > 0000:01:14.0 is tulip built-in. (my guess)
>
> I disagree. The 'Cujo' on GSC bus 8 is actually a Dino. As I said
> in my earlier mail, I've now fixed this.
I couldn't tell if the names were wrong offhand - needed ioscan output
(got it) and compare. Thanks for fixing this.
> So I think eth0 (00:03.0) is actually the built-in one.
I think I got this right despite PCI controller names.
Workstations typically hardwired the PCI slot to use the same device
number (e.g. 3) as what is silk screened on the back of the machine.
Built-in devices were typically given numbers much greater than the
highest slot number.
Servers never did this just because that scheme doesn't work multi-cell
systems with > 32 PCI slots (e.g. superdome) or multiple IO bays with
identical silk screened slot numbers.
thanks,
grant
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
* RE: [parisc-linux] J2240 - Almost there....
2006-01-04 18:18 ` Grant Grundler
@ 2006-01-05 4:08 ` Craig D. Lansing
0 siblings, 0 replies; 25+ messages in thread
From: Craig D. Lansing @ 2006-01-05 4:08 UTC (permalink / raw)
To: 'Grant Grundler', 'Matthew Wilcox'; +Cc: parisc-linux
I forgot about the built-in LAN port. I moved the cable to that one and all
was working from HP-UX, so I restarted the Debian install from CD... it sure
works much better now!!!! The installer doesn't ask for the network info
anymore (i.e. got an IP address from DHCP and did not ask for DNS info,
gateway, etc.), automagically selected eth1 (I guess that implies that eth1
is the built-in and eth0 is the card), and no longer whines about not being
able to reach security.debian.org.
The installer has been busily installing packages for at least 3 hours.
1. Blew up / hung once on:
Setting up libatk1.0-0 (1.8.0-4) ...
module ipv6 relocation of symbol ipv6_chk_addr is out of range (0x3ff3fffd
in 17 bits).
2. Power cycled, booted
I get the "module ipv6..." errors when portmap, PostgreSQL, and Apache2
daemons start.
3. Restarted install via "apt-get -f install". This is my first attempt at
Debian, so I am not APT literate. This is just what I was prompted to do
when I tried to install one package.
Installer is still chugging.
This appears to be a good sign.
-----Original Message-----
From: parisc-linux-bounces@lists.parisc-linux.org
[mailto:parisc-linux-bounces@lists.parisc-linux.org] On Behalf Of Grant
Grundler
Sent: Wednesday, January 04, 2006 1:19 PM
To: Matthew Wilcox
Cc: parisc-linux@lists.parisc-linux.org
Subject: Re: [parisc-linux] J2240 - Almost there....
On Wed, Jan 04, 2006 at 10:49:43AM -0700, Matthew Wilcox wrote:
...
> > 0000:00:03.0 is tulip in slot 3.
> > 0000:01:14.0 is tulip built-in. (my guess)
>
> I disagree. The 'Cujo' on GSC bus 8 is actually a Dino. As I said
> in my earlier mail, I've now fixed this.
I couldn't tell if the names were wrong offhand - needed ioscan output
(got it) and compare. Thanks for fixing this.
> So I think eth0 (00:03.0) is actually the built-in one.
I think I got this right despite PCI controller names.
Workstations typically hardwired the PCI slot to use the same device
number (e.g. 3) as what is silk screened on the back of the machine.
Built-in devices were typically given numbers much greater than the
highest slot number.
Servers never did this just because that scheme doesn't work multi-cell
systems with > 32 PCI slots (e.g. superdome) or multiple IO bays with
identical silk screened slot numbers.
thanks,
grant
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
_______________________________________________
parisc-linux mailing list
parisc-linux@lists.parisc-linux.org
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux
^ permalink raw reply [flat|nested] 25+ messages in thread
end of thread, other threads:[~2006-01-05 4:08 UTC | newest]
Thread overview: 25+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-12-30 15:51 [parisc-linux] J2240 - Almost there Craig D. Lansing
2005-12-30 20:09 ` Kyle McMartin
2005-12-31 3:16 ` Craig D. Lansing
2005-12-31 3:30 ` Kyle McMartin
2005-12-31 16:21 ` Craig D. Lansing
2005-12-31 18:08 ` Grant Grundler
2006-01-01 4:21 ` Craig D. Lansing
2006-01-01 6:32 ` Grant Grundler
2006-01-01 14:15 ` Thibaut VARENE
2006-01-03 1:19 ` Craig D. Lansing
2006-01-03 2:01 ` Matthew Wilcox
2006-01-04 17:43 ` Grant Grundler
2006-01-04 17:49 ` Matthew Wilcox
2006-01-04 18:18 ` Grant Grundler
2006-01-05 4:08 ` Craig D. Lansing
2006-01-03 2:01 ` Craig D. Lansing
2005-12-31 14:43 ` [parisc-linux] " Max Grabert
-- strict thread matches above, loose matches on Subject: below --
2001-11-12 2:43 [parisc-linux] J2240 - Almost There Craig D. Lansing (root)
2001-11-12 6:03 ` Jurriaan on Alpha
2001-11-13 0:07 ` Craig D. Lansing
2001-11-13 0:04 ` Matthew Wilcox
2001-11-13 0:11 ` John David Anglin
2001-11-13 7:40 ` Grant Grundler
2001-11-13 9:03 ` nick
2001-11-12 10:49 ` Albert Strasheim
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.