From: Paul Mundt <lethal@linux-sh.org>
To: akpm@osdl.org, linux-kernel@vger.kernel.org
Subject: [PATCH 8/11] sh: sh-sci clock framework updates.
Date: Sat, 28 Jan 2006 00:53:19 +0200 [thread overview]
Message-ID: <20060127225319.GI30816@linux-sh.org> (raw)
In-Reply-To: <20060127224919.GA30816@linux-sh.org>
A couple of updates for the sh-sci serial driver:
- Update for clock framework on sh.
- Fix a compile error introduced by some h8300 changes.
- Add SH7770/SH7780 subtype support.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
---
drivers/serial/sh-sci.c | 225 +++++++++++++++++++++++++++++++++---------------
drivers/serial/sh-sci.h | 114 ++++++++++++++----------
2 files changed, 223 insertions(+), 116 deletions(-)
da11fe2659737503709e2159a596224b08e002b8
diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c
index a9e0707..12f87d2 100644
--- a/drivers/serial/sh-sci.c
+++ b/drivers/serial/sh-sci.c
@@ -42,6 +42,7 @@
#include <linux/delay.h>
#include <linux/console.h>
#include <linux/bitops.h>
+#include <linux/generic_serial.h>
#ifdef CONFIG_CPU_FREQ
#include <linux/notifier.h>
@@ -53,7 +54,9 @@
#include <asm/irq.h>
#include <asm/uaccess.h>
-#include <linux/generic_serial.h>
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+#include <asm/clock.h>
+#endif
#ifdef CONFIG_SH_STANDARD_BIOS
#include <asm/sh_bios.h>
@@ -86,9 +89,11 @@ static void sci_stop_rx(struct uart_port
static int sci_request_irq(struct sci_port *port);
static void sci_free_irq(struct sci_port *port);
-static struct sci_port sci_ports[SCI_NPORTS];
+static struct sci_port sci_ports[];
static struct uart_driver sci_uart_driver;
+#define SCI_NPORTS sci_uart_driver.nr
+
#if defined(CONFIG_SH_STANDARD_BIOS) || defined(CONFIG_SH_KGDB)
static void handle_error(struct uart_port *port)
@@ -168,7 +173,7 @@ static void put_string(struct sci_port *
int usegdb=0;
#ifdef CONFIG_SH_STANDARD_BIOS
- /* This call only does a trap the first time it is
+ /* This call only does a trap the first time it is
* called, and so is safe to do here unconditionally
*/
usegdb |= sh_bios_in_gdb_mode();
@@ -324,47 +329,46 @@ static void sci_init_pins_sci(struct uar
/* tx mark output*/
H8300_SCI_DR(ch) |= h8300_sci_pins[ch].tx;
}
-#else
-static void sci_init_pins_sci(struct uart_port *port, unsigned int cflag)
-{
-}
#endif
#endif
#if defined(SCIF_ONLY) || defined(SCI_AND_SCIF)
-#if defined(CONFIG_CPU_SH3)
-/* For SH7705, SH7707, SH7709, SH7709A, SH7729, SH7300*/
+#if defined(CONFIG_CPU_SUBTYPE_SH7300)
+/* SH7300 doesn't use RTS/CTS */
+static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
+{
+ sci_out(port, SCFCR, 0);
+}
+#elif defined(CONFIG_CPU_SH3)
+/* For SH7705, SH7707, SH7709, SH7709A, SH7729 */
static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
{
unsigned int fcr_val = 0;
-#if !defined(CONFIG_CPU_SUBTYPE_SH7300) /* SH7300 doesn't use RTS/CTS */
- {
- unsigned short data;
+ unsigned short data;
+
+ /* We need to set SCPCR to enable RTS/CTS */
+ data = ctrl_inw(SCPCR);
+ /* Clear out SCP7MD1,0, SCP6MD1,0, SCP4MD1,0*/
+ ctrl_outw(data & 0x0fcf, SCPCR);
- /* We need to set SCPCR to enable RTS/CTS */
- data = ctrl_inw(SCPCR);
- /* Clear out SCP7MD1,0, SCP6MD1,0, SCP4MD1,0*/
- ctrl_outw(data&0x0fcf, SCPCR);
- }
if (cflag & CRTSCTS)
fcr_val |= SCFCR_MCE;
else {
- unsigned short data;
-
/* We need to set SCPCR to enable RTS/CTS */
data = ctrl_inw(SCPCR);
/* Clear out SCP7MD1,0, SCP4MD1,0,
Set SCP6MD1,0 = {01} (output) */
- ctrl_outw((data&0x0fcf)|0x1000, SCPCR);
+ ctrl_outw((data & 0x0fcf) | 0x1000, SCPCR);
data = ctrl_inb(SCPDR);
/* Set /RTS2 (bit6) = 0 */
- ctrl_outb(data&0xbf, SCPDR);
+ ctrl_outb(data & 0xbf, SCPDR);
}
-#endif
+
sci_out(port, SCFCR, fcr_val);
}
+#if defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
static void sci_init_pins_irda(struct uart_port *port, unsigned int cflag)
{
unsigned int fcr_val = 0;
@@ -374,7 +378,7 @@ static void sci_init_pins_irda(struct ua
sci_out(port, SCFCR, fcr_val);
}
-
+#endif
#else
/* For SH7750 */
@@ -385,7 +389,11 @@ static void sci_init_pins_scif(struct ua
if (cflag & CRTSCTS) {
fcr_val |= SCFCR_MCE;
} else {
+#ifdef CONFIG_CPU_SUBTYPE_SH7780
+ ctrl_outw(0x0080, SCSPTR0); /* Set RTS = 1 */
+#else
ctrl_outw(0x0080, SCSPTR2); /* Set RTS = 1 */
+#endif
}
sci_out(port, SCFCR, fcr_val);
}
@@ -422,7 +430,11 @@ static void sci_transmit_chars(struct ua
#if !defined(SCI_ONLY)
if (port->type == PORT_SCIF) {
+#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+ txroom = SCIF_TXROOM_MAX - (sci_in(port, SCTFDR) & 0x7f);
+#else
txroom = SCIF_TXROOM_MAX - (sci_in(port, SCFDR)>>8);
+#endif
} else {
txroom = (sci_in(port, SCxSR) & SCI_TDRE)?1:0;
}
@@ -491,7 +503,11 @@ static inline void sci_receive_chars(str
while (1) {
#if !defined(SCI_ONLY)
if (port->type == PORT_SCIF) {
+#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+ count = sci_in(port, SCRFDR) & 0x7f;
+#else
count = sci_in(port, SCFDR)&SCIF_RFDC_MASK ;
+#endif
} else {
count = (sci_in(port, SCxSR)&SCxSR_RDxF(port))?1:0;
}
@@ -652,7 +668,7 @@ static inline int sci_handle_breaks(stru
struct tty_struct *tty = port->info->tty;
struct sci_port *s = &sci_ports[port->line];
- if (!s->break_flag && status & SCxSR_BRK(port))
+ if (!s->break_flag && status & SCxSR_BRK(port)) {
#if defined(CONFIG_CPU_SH3)
/* Debounce break */
s->break_flag = 1;
@@ -783,6 +799,7 @@ static int sci_notifier(struct notifier_
(phase == CPUFREQ_RESUMECHANGE)){
for (i = 0; i < SCI_NPORTS; i++) {
struct uart_port *port = &sci_ports[i].port;
+ struct clk *clk;
/*
* Update the uartclk per-port if frequency has
@@ -795,7 +812,9 @@ static int sci_notifier(struct notifier_
*
* Clean this up later..
*/
- port->uartclk = current_cpu_data.module_clock * 16;
+ clk = clk_get("module_clk");
+ port->uartclk = clk_get_rate(clk) * 16;
+ clk_put(clk);
}
printk("%s: got a postchange notification for cpu %d (old %d, new %d)\n",
@@ -1008,15 +1027,20 @@ static void sci_set_termios(struct uart_
sci_out(port, SCSMR, smr_val);
switch (baud) {
- case 0: t = -1; break;
- case 2400: t = BPS_2400; break;
- case 4800: t = BPS_4800; break;
- case 9600: t = BPS_9600; break;
- case 19200: t = BPS_19200; break;
- case 38400: t = BPS_38400; break;
- case 57600: t = BPS_57600; break;
- case 115200: t = BPS_115200; break;
- default: t = SCBRR_VALUE(baud); break;
+ case 0:
+ t = -1;
+ break;
+ default:
+ {
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+ struct clk *clk = clk_get("module_clk");
+ t = SCBRR_VALUE(baud, clk_get_rate(clk));
+ clk_put(clk);
+#else
+ t = SCBRR_VALUE(baud);
+#endif
+ }
+ break;
}
if (t > 0) {
@@ -1030,7 +1054,9 @@ static void sci_set_termios(struct uart_
udelay((1000000+(baud-1)) / baud); /* Wait one bit interval */
}
- s->init_pins(port, termios->c_cflag);
+ if (likely(s->init_pins))
+ s->init_pins(port, termios->c_cflag);
+
sci_out(port, SCSCR, SCSCR_INIT(port));
if ((termios->c_cflag & CREAD) != 0)
@@ -1107,7 +1133,7 @@ static struct uart_ops sci_uart_ops = {
.verify_port = sci_verify_port,
};
-static struct sci_port sci_ports[SCI_NPORTS] = {
+static struct sci_port sci_ports[] = {
#if defined(CONFIG_CPU_SUBTYPE_SH7708)
{
.port = {
@@ -1121,7 +1147,6 @@ static struct sci_port sci_ports[SCI_NPO
},
.type = PORT_SCI,
.irqs = SCI_IRQS,
- .init_pins = sci_init_pins_sci,
},
#elif defined(CONFIG_CPU_SUBTYPE_SH7705)
{
@@ -1165,7 +1190,6 @@ static struct sci_port sci_ports[SCI_NPO
},
.type = PORT_SCI,
.irqs = SCI_IRQS,
- .init_pins = sci_init_pins_sci,
},
{
.port = {
@@ -1225,7 +1249,7 @@ static struct sci_port sci_ports[SCI_NPO
.irqs = SH73180_SCIF_IRQS,
.init_pins = sci_init_pins_scif,
},
-#elif defined(CONFIG_SH_RTS7751R2D)
+#elif defined(CONFIG_CPU_SUBTYPE_SH4_202)
{
.port = {
.membase = (void *)0xffe80000,
@@ -1253,7 +1277,6 @@ static struct sci_port sci_ports[SCI_NPO
},
.type = PORT_SCI,
.irqs = SCI_IRQS,
- .init_pins = sci_init_pins_sci,
},
{
.port = {
@@ -1312,21 +1335,6 @@ static struct sci_port sci_ports[SCI_NPO
.irqs = SH7760_SCIF2_IRQS,
.init_pins = sci_init_pins_scif,
},
-#elif defined(CONFIG_CPU_SUBTYPE_SH4_202)
- {
- .port = {
- .membase = (void *)0xffe80000,
- .mapbase = 0xffe80000,
- .iotype = SERIAL_IO_MEM,
- .irq = 43,
- .ops = &sci_uart_ops,
- .flags = ASYNC_BOOT_AUTOCONF,
- .line = 0,
- },
- .type = PORT_SCIF,
- .irqs = SH4_SCIF_IRQS,
- .init_pins = sci_init_pins_scif,
- },
#elif defined(CONFIG_CPU_SUBTYPE_ST40STB1)
{
.port = {
@@ -1455,6 +1463,78 @@ static struct sci_port sci_ports[SCI_NPO
.irqs = H8S_SCI_IRQS2,
.init_pins = sci_init_pins_sci,
},
+#elif defined(CONFIG_CPU_SUBTYPE_SH7770)
+ {
+ .port = {
+ .membase = (void *)0xff923000,
+ .mapbase = 0xff923000,
+ .iotype = SERIAL_IO_MEM,
+ .irq = 61,
+ .ops = &sci_uart_ops,
+ .flags = ASYNC_BOOT_AUTOCONF,
+ .line = 0,
+ },
+ .type = PORT_SCIF,
+ .irqs = SH7770_SCIF0_IRQS,
+ .init_pins = sci_init_pins_scif,
+ },
+ {
+ .port = {
+ .membase = (void *)0xff924000,
+ .mapbase = 0xff924000,
+ .iotype = SERIAL_IO_MEM,
+ .irq = 62,
+ .ops = &sci_uart_ops,
+ .flags = ASYNC_BOOT_AUTOCONF,
+ .line = 1,
+ },
+ .type = PORT_SCIF,
+ .irqs = SH7770_SCIF1_IRQS,
+ .init_pins = sci_init_pins_scif,
+ },
+ {
+ .port = {
+ .membase = (void *)0xff925000,
+ .mapbase = 0xff925000,
+ .iotype = SERIAL_IO_MEM,
+ .irq = 63,
+ .ops = &sci_uart_ops,
+ .flags = ASYNC_BOOT_AUTOCONF,
+ .line = 2,
+ },
+ .type = PORT_SCIF,
+ .irqs = SH7770_SCIF2_IRQS,
+ .init_pins = sci_init_pins_scif,
+ },
+#elif defined(CONFIG_CPU_SUBTYPE_SH7780)
+ {
+ .port = {
+ .membase = (void *)0xffe00000,
+ .mapbase = 0xffe00000,
+ .iotype = SERIAL_IO_MEM,
+ .irq = 43,
+ .ops = &sci_uart_ops,
+ .flags = ASYNC_BOOT_AUTOCONF,
+ .line = 0,
+ },
+ .type = PORT_SCIF,
+ .irqs = SH7780_SCIF0_IRQS,
+ .init_pins = sci_init_pins_scif,
+ },
+ {
+ .port = {
+ .membase = (void *)0xffe10000,
+ .mapbase = 0xffe10000,
+ .iotype = SERIAL_IO_MEM,
+ .irq = 79,
+ .ops = &sci_uart_ops,
+ .flags = ASYNC_BOOT_AUTOCONF,
+ .line = 1,
+ },
+ .type = PORT_SCIF,
+ .irqs = SH7780_SCIF1_IRQS,
+ .init_pins = sci_init_pins_scif,
+ },
#else
#error "CPU subtype not defined"
#endif
@@ -1480,9 +1560,6 @@ static int __init serial_console_setup(s
int flow = 'n';
int ret;
- if (co->index >= SCI_NPORTS)
- co->index = 0;
-
serial_console_port = &sci_ports[co->index];
port = &serial_console_port->port;
port->type = serial_console_port->type;
@@ -1496,14 +1573,21 @@ static int __init serial_console_setup(s
* We need to set the initial uartclk here, since otherwise it will
* only ever be setup at sci_init() time.
*/
-#if !defined(__H8300H__) && !defined(__H8300S__)
- port->uartclk = current_cpu_data.module_clock * 16;
-#else
+#if defined(__H8300H__) || defined(__H8300S__)
port->uartclk = CONFIG_CPU_CLOCK;
-#endif
+
#if defined(__H8300S__)
h8300_sci_enable(port, sci_enable);
#endif
+#elif defined(CONFIG_SUPERH64)
+ port->uartclk = current_cpu_info.module_clock * 16;
+#else
+ {
+ struct clk *clk = clk_get("module_clk");
+ port->uartclk = clk_get_rate(clk) * 16;
+ clk_put(clk);
+ }
+#endif
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
@@ -1566,7 +1653,7 @@ int __init kgdb_console_setup(struct con
int parity = 'n';
int flow = 'n';
- if (co->index >= SCI_NPORTS || co->index != kgdb_portnum)
+ if (co->index != kgdb_portnum)
co->index = kgdb_portnum;
if (options)
@@ -1606,7 +1693,7 @@ console_initcall(kgdb_console_init);
#elif defined(CONFIG_SERIAL_SH_SCI_CONSOLE)
#define SCI_CONSOLE &serial_console
#else
-#define SCI_CONSOLE 0
+#define SCI_CONSOLE 0
#endif
static char banner[] __initdata =
@@ -1621,7 +1708,6 @@ static struct uart_driver sci_uart_drive
.dev_name = "ttySC",
.major = SCI_MAJOR,
.minor = SCI_MINOR_START,
- .nr = SCI_NPORTS,
.cons = SCI_CONSOLE,
};
@@ -1631,15 +1717,21 @@ static int __init sci_init(void)
printk("%s", banner);
+ sci_uart_driver.nr = ARRAY_SIZE(sci_ports);
+
ret = uart_register_driver(&sci_uart_driver);
if (ret == 0) {
for (chan = 0; chan < SCI_NPORTS; chan++) {
struct sci_port *sciport = &sci_ports[chan];
-#if !defined(__H8300H__) && !defined(__H8300S__)
- sciport->port.uartclk = (current_cpu_data.module_clock * 16);
-#else
+#if defined(__H8300H__) || defined(__H8300S__)
sciport->port.uartclk = CONFIG_CPU_CLOCK;
+#elif defined(CONFIG_SUPERH64)
+ sciport->port.uartclk = current_cpu_info.module_clock * 16;
+#else
+ struct clk *clk = clk_get("module_clk");
+ sciport->port.uartclk = clk_get_rate(clk) * 16;
+ clk_put(clk);
#endif
uart_add_one_port(&sci_uart_driver, &sciport->port);
sciport->break_timer.data = (unsigned long)sciport;
diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h
index 2892169..1f14bb4 100644
--- a/drivers/serial/sh-sci.h
+++ b/drivers/serial/sh-sci.h
@@ -46,14 +46,17 @@
#define H8S_SCI_IRQS1 {92, 93, 94, 0 }
#define H8S_SCI_IRQS2 {96, 97, 98, 0 }
#define SH5_SCIF_IRQS {39, 40, 42, 0 }
+#define SH7770_SCIF0_IRQS {61, 61, 61, 61 }
+#define SH7770_SCIF1_IRQS {62, 62, 62, 62 }
+#define SH7770_SCIF2_IRQS {63, 63, 63, 63 }
+#define SH7780_SCIF0_IRQS {40, 41, 43, 42 }
+#define SH7780_SCIF1_IRQS {76, 77, 79, 78 }
#if defined(CONFIG_CPU_SUBTYPE_SH7708)
-# define SCI_NPORTS 1
# define SCSPTR 0xffffff7c /* 8 bit */
# define SCSCR_INIT(port) 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */
# define SCI_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_SH7707) || defined(CONFIG_CPU_SUBTYPE_SH7709)
-# define SCI_NPORTS 3
# define SCPCR 0xA4000116 /* 16 bit SCI and SCIF */
# define SCPDR 0xA4000136 /* 8 bit SCI and SCIF */
# define SCSCR_INIT(port) 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */
@@ -61,9 +64,8 @@
#elif defined(CONFIG_CPU_SUBTYPE_SH7705)
# define SCIF0 0xA4400000
# define SCIF2 0xA4410000
-# define SCSMR_Ir 0xA44A0000
-# define IRDA_SCIF SCIF0
-# define SCI_NPORTS 2
+# define SCSMR_Ir 0xA44A0000
+# define IRDA_SCIF SCIF0
# define SCPCR 0xA4000116
# define SCPDR 0xA4000136
@@ -74,14 +76,11 @@
# define SCSCR_INIT(port) (port->mapbase == SCIF2) ? 0xF3 : 0xF0
# define SCIF_ONLY
#elif defined(CONFIG_SH_RTS7751R2D)
-# define SCI_NPORTS 1
-# define SCSPTR1 0xffe0001c /* 8 bit SCI */
# define SCSPTR2 0xFFE80020 /* 16 bit SCIF */
# define SCIF_ORER 0x0001 /* overrun error bit */
# define SCSCR_INIT(port) 0x3a /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
# define SCIF_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_SH7750) || defined(CONFIG_CPU_SUBTYPE_SH7751)
-# define SCI_NPORTS 2
# define SCSPTR1 0xffe0001c /* 8 bit SCI */
# define SCSPTR2 0xFFE80020 /* 16 bit SCIF */
# define SCIF_ORER 0x0001 /* overrun error bit */
@@ -90,34 +89,29 @@
0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ )
# define SCI_AND_SCIF
#elif defined(CONFIG_CPU_SUBTYPE_SH7760)
-# define SCI_NPORTS 3
-# define SCSPTR0 0xfe600000 /* 16 bit SCIF */
-# define SCSPTR1 0xfe610000 /* 16 bit SCIF */
-# define SCSPTR2 0xfe620000 /* 16 bit SCIF */
+# define SCSPTR0 0xfe600024 /* 16 bit SCIF */
+# define SCSPTR1 0xfe610024 /* 16 bit SCIF */
+# define SCSPTR2 0xfe620024 /* 16 bit SCIF */
# define SCIF_ORER 0x0001 /* overrun error bit */
# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
# define SCIF_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_SH7300)
-# define SCI_NPORTS 1
# define SCPCR 0xA4050116 /* 16 bit SCIF */
# define SCPDR 0xA4050136 /* 16 bit SCIF */
# define SCSCR_INIT(port) 0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */
# define SCIF_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_SH73180)
-# define SCI_NPORTS 1
# define SCPDR 0xA4050138 /* 16 bit SCIF */
# define SCSPTR2 SCPDR
# define SCIF_ORER 0x0001 /* overrun error bit */
# define SCSCR_INIT(port) 0x0038 /* TIE=0,RIE=0,TE=1,RE=1 */
# define SCIF_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_SH4_202)
-# define SCI_NPORTS 1
# define SCSPTR2 0xffe80020 /* 16 bit SCIF */
# define SCIF_ORER 0x0001 /* overrun error bit */
# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
# define SCIF_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_ST40STB1)
-# define SCI_NPORTS 2
# define SCSPTR1 0xffe00020 /* 16 bit SCIF */
# define SCSPTR2 0xffe80020 /* 16 bit SCIF */
# define SCIF_ORER 0x0001 /* overrun error bit */
@@ -129,26 +123,32 @@
# define SCIF_ADDR_SH5 PHYS_PERIPHERAL_BLOCK+SCIF_BASE_ADDR
# define SCIF_PTR2_OFFS 0x0000020
# define SCIF_LSR2_OFFS 0x0000024
-# define SCI_NPORTS 1
-# define SCI_INIT { \
- { {}, PORT_SCIF, 0, \
- SH5_SCIF_IRQS, sci_init_pins_scif } \
-}
# define SCSPTR2 ((port->mapbase)+SCIF_PTR2_OFFS) /* 16 bit SCIF */
# define SCLSR2 ((port->mapbase)+SCIF_LSR2_OFFS) /* 16 bit SCIF */
# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,
TE=1,RE=1,REIE=1 */
# define SCIF_ONLY
#elif defined(CONFIG_H83007) || defined(CONFIG_H83068)
-# define SCI_NPORTS 3
# define SCSCR_INIT(port) 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */
# define SCI_ONLY
# define H8300_SCI_DR(ch) *(volatile char *)(P1DR + h8300_sci_pins[ch].port)
#elif defined(CONFIG_H8S2678)
-# define SCI_NPORTS 3
# define SCSCR_INIT(port) 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */
# define SCI_ONLY
# define H8300_SCI_DR(ch) *(volatile char *)(P1DR + h8300_sci_pins[ch].port)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7770)
+# define SCSPTR0 0xff923020 /* 16 bit SCIF */
+# define SCSPTR1 0xff924020 /* 16 bit SCIF */
+# define SCSPTR2 0xff925020 /* 16 bit SCIF */
+# define SCIF_ORER 0x0001 /* overrun error bit */
+# define SCSCR_INIT(port) 0x3c /* TIE=0,RIE=0,TE=1,RE=1,REIE=1,cke=2 */
+# define SCIF_ONLY
+#elif defined(CONFIG_CPU_SUBTYPE_SH7780)
+# define SCSPTR0 0xffe00024 /* 16 bit SCIF */
+# define SCSPTR1 0xffe10024 /* 16 bit SCIF */
+# define SCIF_OPER 0x0001 /* Overrun error bit */
+# define SCSCR_INIT(port) 0x3a /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
+# define SCIF_ONLY
#else
# error CPU subtype not defined
#endif
@@ -158,7 +158,7 @@
#define SCI_CTRL_FLAGS_RIE 0x40 /* all */
#define SCI_CTRL_FLAGS_TE 0x20 /* all */
#define SCI_CTRL_FLAGS_RE 0x10 /* all */
-#if defined(CONFIG_CPU_SUBTYPE_SH7750) || defined(CONFIG_CPU_SUBTYPE_SH7751)
+#if defined(CONFIG_CPU_SUBTYPE_SH7750) || defined(CONFIG_CPU_SUBTYPE_SH7751) || defined(CONFIG_CPU_SUBTYPE_SH7780)
#define SCI_CTRL_FLAGS_REIE 0x08 /* 7750 SCIF */
#else
#define SCI_CTRL_FLAGS_REIE 0
@@ -213,7 +213,7 @@
# define SCxSR_RDxF_CLEAR(port) 0xbc
# define SCxSR_ERROR_CLEAR(port) 0xc4
# define SCxSR_TDxE_CLEAR(port) 0x78
-# define SCxSR_BREAK_CLEAR(port) 0xc4
+# define SCxSR_BREAK_CLEAR(port) 0xc4
#elif defined(SCIF_ONLY)
# define SCxSR_TEND(port) SCIF_TEND
# define SCxSR_ERRORS(port) SCIF_ERRORS
@@ -237,7 +237,7 @@
# define SCxSR_RDxF_CLEAR(port) 0x00fc
# define SCxSR_ERROR_CLEAR(port) 0x0073
# define SCxSR_TDxE_CLEAR(port) 0x00df
-# define SCxSR_BREAK_CLEAR(port) 0x00e3
+# define SCxSR_BREAK_CLEAR(port) 0x00e3
#endif
#else
# define SCxSR_TEND(port) (((port)->type == PORT_SCI) ? SCI_TEND : SCIF_TEND)
@@ -285,14 +285,14 @@ struct sci_port {
#define SCI_IN(size, offset) \
unsigned int addr = port->mapbase + (offset); \
- if ((size) == 8) { \
+ if ((size) == 8) { \
return ctrl_inb(addr); \
- } else { \
+ } else { \
return ctrl_inw(addr); \
}
#define SCI_OUT(size, offset, value) \
unsigned int addr = port->mapbase + (offset); \
- if ((size) == 8) { \
+ if ((size) == 8) { \
ctrl_outb(value, addr); \
} else { \
ctrl_outw(value, addr); \
@@ -301,10 +301,10 @@ struct sci_port {
#define CPU_SCIx_FNS(name, sci_offset, sci_size, scif_offset, scif_size)\
static inline unsigned int sci_##name##_in(struct uart_port *port) \
{ \
- if (port->type == PORT_SCI) { \
+ if (port->type == PORT_SCI) { \
SCI_IN(sci_size, sci_offset) \
} else { \
- SCI_IN(scif_size, scif_offset); \
+ SCI_IN(scif_size, scif_offset); \
} \
} \
static inline void sci_##name##_out(struct uart_port *port, unsigned int value) \
@@ -319,7 +319,7 @@ struct sci_port {
#define CPU_SCIF_FNS(name, scif_offset, scif_size) \
static inline unsigned int sci_##name##_in(struct uart_port *port) \
{ \
- SCI_IN(scif_size, scif_offset); \
+ SCI_IN(scif_size, scif_offset); \
} \
static inline void sci_##name##_out(struct uart_port *port, unsigned int value) \
{ \
@@ -329,7 +329,7 @@ struct sci_port {
#define CPU_SCI_FNS(name, sci_offset, sci_size) \
static inline unsigned int sci_##name##_in(struct uart_port* port) \
{ \
- SCI_IN(sci_size, sci_offset); \
+ SCI_IN(sci_size, sci_offset); \
} \
static inline void sci_##name##_out(struct uart_port* port, unsigned int value) \
{ \
@@ -385,10 +385,17 @@ SCIx_FNS(SCxTDR, 0x06, 8, 0x0c, 8, 0x0
SCIx_FNS(SCxSR, 0x08, 8, 0x10, 8, 0x08, 16, 0x10, 16, 0x04, 8)
SCIx_FNS(SCxRDR, 0x0a, 8, 0x14, 8, 0x0A, 8, 0x14, 8, 0x05, 8)
SCIF_FNS(SCFCR, 0x0c, 8, 0x18, 16)
+#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+SCIF_FNS(SCTFDR, 0x0e, 16, 0x1C, 16)
+SCIF_FNS(SCRFDR, 0x0e, 16, 0x20, 16)
+SCIF_FNS(SCSPTR, 0, 0, 0x24, 16)
+SCIF_FNS(SCLSR, 0, 0, 0x28, 16)
+#else
SCIF_FNS(SCFDR, 0x0e, 16, 0x1C, 16)
SCIF_FNS(SCSPTR, 0, 0, 0x20, 16)
SCIF_FNS(SCLSR, 0, 0, 0x24, 16)
#endif
+#endif
#define sci_in(port, reg) sci_##reg##_in(port)
#define sci_out(port, reg, value) sci_##reg##_out(port, value)
@@ -518,6 +525,24 @@ static inline int sci_rxd_in(struct uart
int ch = (port->mapbase - SMR0) >> 3;
return (H8300_SCI_DR(ch) & h8300_sci_pins[ch].rx) ? 1 : 0;
}
+#elif defined(CONFIG_CPU_SUBTYPE_SH7770)
+static inline int sci_rxd_in(struct uart_port *port)
+{
+ if (port->mapbase == 0xff923000)
+ return ctrl_inw(SCSPTR0) & 0x0001 ? 1 : 0; /* SCIF */
+ if (port->mapbase == 0xff924000)
+ return ctrl_inw(SCSPTR1) & 0x0001 ? 1 : 0; /* SCIF */
+ if (port->mapbase == 0xff925000)
+ return ctrl_inw(SCSPTR2) & 0x0001 ? 1 : 0; /* SCIF */
+}
+#elif defined(CONFIG_CPU_SUBTYPE_SH7780)
+static inline int sci_rxd_in(struct uart_port *port)
+{
+ if (port->mapbase == 0xffe00000)
+ return ctrl_inw(SCSPTR0) & 0x0001 ? 1 : 0; /* SCIF */
+ if (port->mapbase == 0xffe10000)
+ return ctrl_inw(SCSPTR1) & 0x0001 ? 1 : 0; /* SCIF */
+}
#endif
/*
@@ -552,22 +577,15 @@ static inline int sci_rxd_in(struct uart
* -- Mitch Davis - 15 Jul 2000
*/
-#define PCLK (current_cpu_data.module_clock)
-
-#if defined(CONFIG_CPU_SUBTYPE_SH7300)
-#define SCBRR_VALUE(bps) ((PCLK+16*bps)/(16*bps)-1)
+#if defined(CONFIG_CPU_SUBTYPE_SH7300) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+#define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(16*bps)-1)
#elif defined(CONFIG_CPU_SUBTYPE_SH7705)
-#define SCBRR_VALUE(bps) (((PCLK*2)+16*bps)/(32*bps)-1)
-#elif !defined(__H8300H__) && !defined(__H8300S__)
-#define SCBRR_VALUE(bps) ((PCLK+16*bps)/(32*bps)-1)
-#else
+#define SCBRR_VALUE(bps, clk) (((clk*2)+16*bps)/(32*bps)-1)
+#elif defined(__H8300H__) || defined(__H8300S__)
#define SCBRR_VALUE(bps) (((CONFIG_CPU_CLOCK*1000/32)/bps)-1)
+#elif defined(CONFIG_SUPERH64)
+#define SCBRR_VALUE(bps) ((current_cpu_data.module_clock+16*bps)/(32*bps)-1)
+#else /* Generic SH */
+#define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(32*bps)-1)
#endif
-#define BPS_2400 SCBRR_VALUE(2400)
-#define BPS_4800 SCBRR_VALUE(4800)
-#define BPS_9600 SCBRR_VALUE(9600)
-#define BPS_19200 SCBRR_VALUE(19200)
-#define BPS_38400 SCBRR_VALUE(38400)
-#define BPS_57600 SCBRR_VALUE(57600)
-#define BPS_115200 SCBRR_VALUE(115200)
next prev parent reply other threads:[~2006-01-27 22:55 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-01-27 22:49 [PATCH 0/11] sh cleanups Paul Mundt
2006-01-27 22:50 ` [PATCH 1/11] sh: SH4-202 microdev updates Paul Mundt
2006-01-27 22:50 ` [PATCH 2/11] sh: Make peripheral clock frequency setting mandatory Paul Mundt
2006-01-28 0:38 ` Andrew Morton
2006-01-27 22:51 ` [PATCH 3/11] sh: Move TRA/EXPEVT/INTEVT definitions for reuse Paul Mundt
2006-01-27 22:51 ` [PATCH 4/11] sh: Cleanup struct sh_cpuinfo for clock framework changes Paul Mundt
2006-01-27 22:51 ` [PATCH 5/11] sh: unknown mach-type updates Paul Mundt
2006-01-27 22:52 ` [PATCH 6/11] sh: drop maskpos from make_ipr_irq(), remove duplicate irq definitions Paul Mundt
2006-01-27 22:52 ` [PATCH 7/11] sh: convert voyagergx to platform device, drop sh-bus Paul Mundt
2006-01-27 22:53 ` Paul Mundt [this message]
2006-01-27 22:53 ` [PATCH 9/11] sh: Add missing timers directory rule to build Paul Mundt
2006-01-27 22:53 ` [PATCH 10/11] sh: machine_halt()/machine_power_off() cleanups Paul Mundt
2006-01-27 22:54 ` [PATCH 11/11] sh/sh64: Fix bogus TIOCGICOUNT definitions Paul Mundt
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060127225319.GI30816@linux-sh.org \
--to=lethal@linux-sh.org \
--cc=akpm@osdl.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.