From: Sander <sander@humilis.net>
To: Sander <sander@humilis.net>
Cc: Jeff Garzik <jgarzik@pobox.com>, linux-kernel@vger.kernel.org
Subject: Re: 2.6.16-rc3 kernel BUG at drivers/scsi/sata_mv.c:1018
Date: Wed, 15 Feb 2006 15:33:46 +0100 [thread overview]
Message-ID: <20060215143346.GB26178@favonius> (raw)
In-Reply-To: <20060215131653.GA26178@favonius>
Sander wrote (ao):
# Hi Jeff and others,
#
# I get a kernel BUG message when I try to create a raid1 or raid5 over
# nine 64MB partitions located on nine sata disks (Maxtor Pro 500) on a
# fresh setup. The system locks hard: no sysrq.
#
# The onboard controller is an nVidia nForce with three disks.
# The six other disks are connected to a Marvell 88SX6081 controller.
#
# Last night and the first half of today all disks were tested with
# badblocks in write mode, which the system survived just fine (one disk
# out of ten detected as broken, so nine disks left).
#
# A google search leads me to
#
# http://www.uwsg.iu.edu/hypermail/linux/kernel/0601.2/0479.html
#
# and
#
# http://www.uwsg.iu.edu/hypermail/linux/kernel/0601.2/0626.html
#
# I had MSI disabled in the .config already, and will try again with debug
# options set.
#
# In the mean time, is this of any help?
#
# I can try any patch you throw at me, or any config option, as this
# system is not in production yet.
#
# Sander
#
# Linux version 2.6.16-rc3 (root@elisha) (gcc version 4.0.3 20060104 (prerelease) (Debian 4.0.2-6))
#
# mdadm -C -l1 -n9 /dev/md0 /dev/sda1 /dev/sdb1 /dev/sdc1 \
# /dev/sdd1 /dev/sde1 /dev/sdf1 /dev/sdg1 /dev/sdh1 /dev/sdi1
#
# [19697.866199] md: bind<sda1>
# [19697.866251] md: bind<sdc1>
# [19697.866294] md: bind<sdd1>
# [19697.866332] md: bind<sde1>
# [19697.866374] md: bind<sdf1>
# [19697.866414] md: bind<sdg1>
# [19697.866454] md: bind<sdh1>
# [19697.866492] md: bind<sdi1>
# [19697.866531] md: bind<sdj1>
# [19697.866734] raid1: raid set md0 active with 9 out of 9 mirrors
# [19697.866888] ----------- [cut here ] --------- [please bite here ] ---------
# [19697.866921] Kernel BUG at drivers/scsi/sata_mv.c:1018
# [19697.866950] invalid opcode: 0000 [1] SMP
# [19697.866984] CPU 1
# [19697.867010] Modules linked in:
# [19697.867040] Pid: 2491, comm: mdadm Not tainted 2.6.16-rc3 #1
# [19697.867075] RIP: 0010:[<ffffffff8029975a>] <ffffffff8029975a>{mv_qc_prep+307}
# [19697.867103] RSP: 0000:ffff81013fc9bd28 EFLAGS: 00010002
# [19697.867152] RAX: ffff81000c63f03d RBX: ffff81013a691500 RCX: ffff81000c63f02a
# [19697.867186] RDX: ffff81013a5639d8 RSI: 0000000000000046 RDI: ffff81013a5639b8
# [19697.867220] RBP: ffff81013a5639b8 R08: 0000000000000004 R09: ffff81013fc9bc4c
# [19697.867267] R10: 00000000000000c3 R11: ffffffff802e188d R12: 0000000000000000
# [19697.867302] R13: ffff81013a563480 R14: ffffffff8027d502 R15: ffff81013a563480
# [19697.867335] FS: 00002b35e01f7ae0(0000) GS:ffff81013fc759c0(0000) knlGS:0000000000000000
# [19697.867384] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
# [19697.867415] CR2: 0000000000511768 CR3: 00000001333fc000 CR4: 00000000000006e0
# [19697.867450] Process mdadm (pid: 2491, threadinfo ffff81013a040000, task ffff81013a591020)
# [19697.867497] Stack: ffff81013a5639b8 ffff81013a5639b8 ffff81013a603280 ffffffff802932bd
# [19697.867546] ffff81013a603280 ffff81013a5639b8 ffff81013a562280 ffff81013a563558
# [19697.867624] ffff81013a563480 ffffffff8027d502
# [19697.867662] Call Trace: <IRQ> <ffffffff802932bd>{ata_qc_issue+794}
# [19697.867710] <ffffffff8027d502>{scsi_done+0} <ffffffff8029765d>{ata_scsi_translate+172}
# [19697.867778] <ffffffff802972ae>{ata_scsi_rw_xlat+0} <ffffffff8027d502>{scsi_done+0}
I would like to add that this is on a 64bit Opteron system. With these
debug options enabled, I get (albeit little) extra output.
Is there anything I can do to get more output?
CONFIG_PRINTK_TIME=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_KERNEL=y
CONFIG_LOG_BUF_SHIFT=17
CONFIG_DETECT_SOFTLOCKUP=y
# CONFIG_SCHEDSTATS is not set
CONFIG_DEBUG_SLAB=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_SPINLOCK_SLEEP=y
CONFIG_DEBUG_KOBJECT=y
# CONFIG_DEBUG_INFO is not set
# CONFIG_DEBUG_FS is not set
# CONFIG_DEBUG_VM is not set
CONFIG_FRAME_POINTER=y
# CONFIG_FORCED_INLINING is not set
# CONFIG_RCU_TORTURE_TEST is not set
# CONFIG_DEBUG_RODATA is not set
# CONFIG_IOMMU_DEBUG is not set
[ 500.043196] md: bind<sda1>
[ 500.043320] md: bind<sdb1>
[ 500.046718] md: bind<sdc1>
[ 500.046828] md: bind<sdd1>
[ 500.046935] md: bind<sde1>
[ 500.047043] md: bind<sdf1>
[ 500.047147] md: bind<sdg1>
[ 500.047254] md: bind<sdh1>
[ 500.047357] md: bind<sdi1>
[ 500.047834] raid1: raid set md0 active with 9 out of 9 mirrors
[ 500.048039] ----------- [cut here ] --------- [please bite here ] ---------
[ 500.048093] Kernel BUG at drivers/scsi/sata_mv.c:1018
[ 500.048143] invalid opcode: 0000 [1] SMP
[ 500.048241] CPU 1
[ 500.048309] Modules linked in:
[ 500.048381] Pid: 2379, comm: mdadm Not tainted 2.6.16-rc3 #1
[ 500.048431] RIP: 0010:[<ffffffff802b17e3>] <ffffffff802b17e3>{mv_qc_prep+320}
[ 500.048503] RSP: 0000:ffff81013fca7bd8 EFLAGS: 00010002
[ 500.048592] RAX: ffff810006c9a03d RBX: ffff81013b35dda0 RCX: ffff810006c9a08a
[ 500.048646] RDX: ffff81013ac44aa0 RSI: 0000000000000092 RDI: ffff81013ac44a80
[ 500.048701] RBP: ffff81013fca7bf8 R08: 0000000000000004 R09: ffff81013fca7afc
[ 500.048757] R10: 00000000000000c3 R11: ffffffff80585968 R12: ffff81013ac44a80
[ 500.048812] R13: 0000000000000000 R14: ffff81013ac44548 R15: ffffffff80293f69
[ 500.048867] FS: 00002adb0f5c4ae0(0000) GS:ffff81013fc52e88(0000) knlGS:0000000000000000
[ 500.048936] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 500.048990] CR2: 00007ffffff98e98 CR3: 000000013295c000 CR4: 00000000000006e0
[ 500.049046] Process mdadm (pid: 2379, threadinfo ffff81013a26e000, task ffff81013b2b7820)
[ 500.049114] Stack: ffff81013b385a48 ffff81013ac44548 ffff81013ac44a80 ffff81013b385a48
[ 500.049277] ffff81013fca7c48 ffffffff802aae98 ffff81013fca7c48 ffff81013ac44548
[ 500.049491] ffff81013b385a48 ffff81013ac44a80
[ 500.049622] Call Trace: <IRQ> <ffffffff802aae98>{ata_qc_issue+855}
[ 500.049779] <ffffffff80293f69>{scsi_done+0} <ffffffff802af549>{ata_scsi_translate+190}
[ 500.049958] <ffffffff802af187>{ata_scsi_rw_xlat+0} <ffffffff80293f69>{scsi_done+0}
[ 535.019510] BUG: spinlock lockup on CPU#1, mdadm/2379, ffff81013f6c4b78
[ 535.019561]
[ 535.019562] Call Trace: <IRQ> <ffffffff80217e87>{_raw_spin_lock+219}
[ 535.019718] <ffffffff80398a25>{_spin_lock+9} <ffffffff802b1d6f>{mv_interrupt+86}
[ 535.019889] <ffffffff801403af>{handle_IRQ_event+48} <ffffffff8014048f>{__do_IRQ+167}
[ 535.020064] <ffffffff8010d2c5>{do_IRQ+62} <ffffffff8010ae64>{ret_from_intr+0}
[ 535.020236] <ffffffff80114a5f>{smp_send_stop+71} <ffffffff80123819>{panic+165}
[ 535.023678] <ffffffff8010beee>{show_stack+211} <ffffffff8012604c>{do_exit+133}
[ 535.023851] <ffffffff8010c3e9>{kernel_math_error+0} <ffffffff8010c999>{do_trap+237}
[ 535.024022] <ffffffff80293f69>{scsi_done+0} <ffffffff8010ce10>{do_invalid_op+157}
[ 535.024194] <ffffffff802b17e3>{mv_qc_prep+320} <ffffffff802fe42a>{pci_conf1_read+204}
[ 535.024523] <ffffffff8021bfbb>{pci_bus_read_config_dword+121} <ffffffff8010b5fd>{error_exit+0}
[ 535.024696] <ffffffff80293f69>{scsi_done+0} <ffffffff802b17e3>{mv_qc_prep+320}
[ 535.024868] <ffffffff802aae98>{ata_qc_issue+855} <ffffffff80293f69>{scsi_done+0}
[ 535.025038] <ffffffff802af549>{ata_scsi_translate+190}
--
Humilis IT Services and Solutions
http://www.humilis.net
next prev parent reply other threads:[~2006-02-15 14:33 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-02-15 13:16 2.6.16-rc3 kernel BUG at drivers/scsi/sata_mv.c:1018 Sander
2006-02-15 14:33 ` Sander [this message]
2006-02-15 14:59 ` Jens Axboe
2006-02-15 16:31 ` Sander
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060215143346.GB26178@favonius \
--to=sander@humilis.net \
--cc=jgarzik@pobox.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.