From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: Received: from mx2.suse.de (mx2.suse.de [195.135.220.15]) (using TLSv1 with cipher DHE-RSA-AES256-SHA (256/256 bits)) (Client CN "mx2.suse.de", Issuer "Thawte Premium Server CA" (verified OK)) by ozlabs.org (Postfix) with ESMTP id 63FB4679FB for ; Tue, 28 Feb 2006 03:09:16 +1100 (EST) Date: Mon, 27 Feb 2006 17:09:11 +0100 From: Olaf Hering To: Benjamin Herrenschmidt , linuxppc-dev@ozlabs.org Subject: copying /sys causes fans to spin up Message-ID: <20060227160911.GA17569@suse.de> Mime-Version: 1.0 Content-Type: text/plain; charset=utf-8 List-Id: Linux on PowerPC Developers Mail List List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Ben, some tool copies /sys, and while doing it, the fans start to spin up on my G5. Any idea how to fix it, other than not reading from /sys? Have to find the exact file. Page orders: linear mapping = 24, others = 12 Found initrd at 0xc000000001100000:0xc0000000013e8000 Found U3 memory controller & host bridge @ 0xf8000000 revision: 0x32 Mapped at 0xd000080080000000 Found a K2 mac-io controller, rev: 32, mapped at 0xd000080080041000 PowerMac motherboard: PowerMac G5 Using native/NAP idle loop DART: table not allocated, using direct DMA Starting Linux PPC64 #1 SMP Mon Feb 20 15:56:05 UTC 2006 ----------------------------------------------------- ppc64_pft_size = 0x0 ppc64_interrupt_controller = 0x1 platform = 0x400 physicalMemorySize = 0x10000000 ppc64_caches.dcache_line_size = 0x80 ppc64_caches.icache_line_size = 0x80 htab_address = 0xc00000000f800000 htab_hash_mask = 0x7fff ----------------------------------------------------- [boot]0100 MM Init [boot]0100 MM Init Done Linux version 2.6.16-rc4-3-ppc64 (geeko@buildhost) (gcc version 4.1.0 20060218 (prerelease) (SUSE Linux)) #1 SMP Mon Feb 20 15:56:05 UTC 2006 [boot]0012 Setup Arch Top of RAM: 0x10000000, Total RAM: 0x10000000 Memory hole size: 0MB Found U3-AGP PCI host bridge. Firmware bus number: 240->255 Can't get bus-range for /ht@0,f2000000, assume bus 0 Found U3-HT PCI host bridge. Firmware bus number: 0->239 PCI Host 0, io start: 400000; io end: bfffff PCI Host 1, io start: 0; io end: 3fffff via-pmu: Server Mode is disabled PMU driver v2 initialized for Core99, firmware: 0c nvram: Checking bank 0... nvram: gen0=445, gen1=444 nvram: Active bank is: 0 nvram: OF partition at 0x410 nvram: XP partition at 0x1020 nvram: NR partition at 0x1120 On node 0 totalpages: 65536 DMA zone: 65536 pages, LIFO batch:15 DMA32 zone: 0 pages, LIFO batch:0 Normal zone: 0 pages, LIFO batch:0 HighMem zone: 0 pages, LIFO batch:0 [boot]0015 Setup Done Built 1 zonelists Kernel command line: quiet sysrq=1 root=/dev/disk/by-path/pci-0001:05:0c.0-scsi-0:0:0:0-part11 root=/dev/sda11 mpic: Setting up MPIC " MPIC 1 " version 1.2 at 80040000, max 4 CPUs mpic: ISU size: 120, shift: 7, mask: 7f mpic: Initializing for 120 sources mpic: Setting up MPIC " MPIC 2 " version 1.2 at f8040000, max 4 CPUs mpic: ISU size: 120, shift: 7, mask: 7f mpic: Initializing for 120 sources PID hash table entries: 2048 (order: 11, 65536 bytes) time_init: decrementer frequency = 33.333333 MHz time_init: processor frequency = 1600.000000 MHz Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) freeing bootmem node 0 Memory: 242736k/262144k available (4336k kernel code, 19408k reserved, 1952k data, 851k bss, 256k init) Calibrating delay loop... 66.56 BogoMIPS (lpj=332800) Security Framework v1.0.0 initialized Mount-cache hash table entries: 256 checking if image is initramfs... it is Freeing initrd memory: 2976k freed PowerMac SMP probe found 1 cpus Brought up 1 CPUs migration_cost=0 NET: Registered protocol family 16 KeyWest i2c @0xf8001003 irq 170 /u3@0,f8000000/i2c@f8001000 channel 0 bus channel 1 bus KeyWest i2c @0x80018000 irq 26 /ht@0,f2000000/pci@3/mac-io@7/i2c@18000 channel 0 bus PMU i2c /ht@0,f2000000/pci@3/mac-io@7/via-pmu@16000/pmu-i2c channel 1 bus channel 2 bus Installing base platform functions... Installing MMIO functions for macio /ht@0,f2000000/pci@3/mac-io@7 Installing GPIO functions for macio /ht@0,f2000000/pci@3/mac-io@7 Calling initial GPIO functions for macio /ht@0,f2000000/pci@3/mac-io@7 Do write 0x82 to GPIO /ht@0,f2000000/pci@3/mac-io@7/gpio@50/line-input-detect@c (d00008008004105c) Do write 0x80 to GPIO /ht@0,f2000000/pci@3/mac-io@7/gpio@50/line-output-detect@16 (d000080080041066) Do write 0x82 to GPIO /ht@0,f2000000/pci@3/mac-io@7/gpio@50/headphone-detect@17 (d000080080041067) Installing functions for UniN /u3@0,f8000000 All base functions installed PCI: Probing PCI hardware Can't get ranges for PCI-PCI bridge /ht@0,f2000000/pci@2 mapping IO f0000000 -> d000080000400000, size: 800000 mapping IO f4000000 -> d000080000000000, size: 400000 PCI: Probing PCI hardware done Registering pmac pic with sysfs... usbcore: registered new driver usbfs usbcore: registered new driver hub TC classifier action (bugs to netdev@vger.kernel.org cc hadi@cyberus.ca) IBM eBus Device Driver nvram_init: Could not find nvram partition for nvram buffered error logging. Registering G5 CPU frequency driver Frequency method: i2c/pfunc, Voltage method: i2c/pfunc Low: 1301 Mhz, High: 1600 Mhz, Cur: 1600 MHz audit: initializing netlink socket (disabled) audit(1141055721.759:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) nvidiafb: PCI id - 10de0321 nvidiafb: Actual id - 10de0321 nvidiafb: nVidia device/chipset 10DE0321 nvidiafb: CRTC0 analog not found nvidiafb: CRTC1 analog not found nvidiafb: EDID found from BUS2 nvidiafb: CRTC 1 is currently programmed for DFP nvidiafb: Using DFP on CRTC 1 Panel size is 1680 x 1050 nvidiafb: Flat panel dithering disabled Console: switching to colour frame buffer device 210x65 nvidiafb: PCI nVidia NV32 framebuffer (64MB @ 0xA8000000) vio_register_driver: driver hvc_console registering HVSI: registered 0 devices Generic RTC Driver v1.07 pmac_zilog: 0.6 (Benjamin Herrenschmidt ) ttyS0 at MMIO 0x80013020 (irq = 22) is a Z85c30 ESCC - Serial port ttyS1 at MMIO 0x80013000 (irq = 23) is a Z85c30 ESCC - Serial port RAMDISK driver initialized: 16 RAM disks of 123456K size 1024 blocksize MacIO PCI driver attached to K2 chipset input: Macintosh mouse button emulation as /class/input/input0 PowerMac G5 Thermal control driver 1.2b2 adb: starting probe task... adb: finished probe task... Detected fan controls: 0: PWM fan, id 1, location: BACKSIDE,SYS CTRLR FAN 1: RPM fan, id 2, location: DRIVE BAY 2: PWM fan, id 2, location: SLOT,PCI FAN 3: RPM fan, id 3, location: CPU A INTAKE 4: RPM fan, id 4, location: CPU A EXHAUST 5: RPM fan, id 5, location: CPU B INTAKE 6: RPM fan, id 6, location: CPU B EXHAUST Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx PCI: Enabling device: (0001:03:0d.0), cmd 16 ide0: Found Apple K2 ATA-6 controller, bus ID 3, irq 39 Probing IDE interface ide0... hda: PIONEER DVD-RW DVR-106D, ATAPI CD/DVD-ROM drive hda: Enabling Ultra DMA 2 ide0 at 0xd0000800872eb000-0xd0000800872eb007,0xd0000800872eb160 on irq 39 PCI: Enabling device: (0001:02:0b.2), cmd 6 ehci_hcd 0001:02:0b.2: EHCI Host Controller ehci_hcd 0001:02:0b.2: new USB bus registered, assigned bus number 1 ehci_hcd 0001:02:0b.2: irq 63, io mem 0x80100000 ehci_hcd 0001:02:0b.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: new device found, idVendor=0000, idProduct=0000 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.16-rc4-3-ppc64 ehci_hcd usb usb1: SerialNumber: 0001:02:0b.2 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 5 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) PCI: Enabling device: (0001:01:08.0), cmd 2 ohci_hcd 0001:01:08.0: OHCI Host Controller ohci_hcd 0001:01:08.0: new USB bus registered, assigned bus number 2 ohci_hcd 0001:01:08.0: irq 27, io mem 0x80081000 usb usb2: new device found, idVendor=0000, idProduct=0000 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.16-rc4-3-ppc64 ohci_hcd usb usb2: SerialNumber: 0001:01:08.0 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected PCI: Enabling device: (0001:01:09.0), cmd 2 ohci_hcd 0001:01:09.0: OHCI Host Controller ohci_hcd 0001:01:09.0: new USB bus registered, assigned bus number 3 ohci_hcd 0001:01:09.0: irq 28, io mem 0x80080000 usb usb3: new device found, idVendor=0000, idProduct=0000 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: OHCI Host Controller usb usb3: Manufacturer: Linux 2.6.16-rc4-3-ppc64 ohci_hcd usb usb3: SerialNumber: 0001:01:09.0 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected PCI: Enabling device: (0001:02:0b.0), cmd 2 ohci_hcd 0001:02:0b.0: OHCI Host Controller ohci_hcd 0001:02:0b.0: new USB bus registered, assigned bus number 4 ohci_hcd 0001:02:0b.0: irq 63, io mem 0x80102000 usb usb4: new device found, idVendor=0000, idProduct=0000 usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb4: Product: OHCI Host Controller usb usb4: Manufacturer: Linux 2.6.16-rc4-3-ppc64 ohci_hcd usb usb4: SerialNumber: 0001:02:0b.0 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 3 ports detected PCI: Enabling device: (0001:02:0b.1), cmd 2 ohci_hcd 0001:02:0b.1: OHCI Host Controller ohci_hcd 0001:02:0b.1: new USB bus registered, assigned bus number 5 ohci_hcd 0001:02:0b.1: irq 63, io mem 0x80101000 usb usb5: new device found, idVendor=0000, idProduct=0000 usb usb5: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb5: Product: OHCI Host Controller usb usb5: Manufacturer: Linux 2.6.16-rc4-3-ppc64 ohci_hcd usb usb5: SerialNumber: 0001:02:0b.1 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected usb 4-2: new full speed USB device using ohci_hcd and address 2 usb 4-2: new device found, idVendor=05ac, idProduct=1003 usb 4-2: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 4-2: Product: Hub in Apple Extended USB Keyboard usb 4-2: Manufacturer: Mitsumi Electric usb 4-2: configuration #1 chosen from 1 choice hub 4-2:1.0: USB hub found hub 4-2:1.0: 3 ports detected usb 5-2: new full speed USB device using ohci_hcd and address 2 usb 5-2: new device found, idVendor=06cd, idProduct=0110 usb 5-2: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 5-2: Product: Keyspan USB Serial Adapter usb 5-2: Manufacturer: Keyspan, a division of InnoSys Inc. usb 5-2: configuration #1 chosen from 2 choices usb 4-2.1: new low speed USB device using ohci_hcd and address 3 usb 4-2.1: new device found, idVendor=05ac, idProduct=0307 usb 4-2.1: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 4-2.1: Product: Apple Optical USB Mouse usb 4-2.1: Manufacturer: Logitech usb 4-2.1: configuration #1 chosen from 1 choice usb 4-2.3: new full speed USB device using ohci_hcd and address 4 usb 4-2.3: new device found, idVendor=05ac, idProduct=020c usb 4-2.3: new device strings: Mfr=1, Product=3, SerialNumber=0 usb 4-2.3: Product: Apple Extended USB Keyboard usb 4-2.3: Manufacturer: Mitsumi Electric usb 4-2.3: configuration #1 chosen from 1 choice usbcore: registered new driver hiddev input: Logitech Apple Optical USB Mouse as /class/input/input1 input: USB HID v1.10 Mouse [Logitech Apple Optical USB Mouse] on usb-0001:02:0b.0-2.1 input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input2 input: USB HID v1.10 Keyboard [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:02:0b.0-2.3 input: Mitsumi Electric Apple Extended USB Keyboard as /class/input/input3 input: USB HID v1.10 Device [Mitsumi Electric Apple Extended USB Keyboard] on usb-0001:02:0b.0-2.3 usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice PowerMac i2c bus pmu 2 registered PowerMac i2c bus pmu 1 registered PowerMac i2c bus mac-io 0 registered found max6690, loc=BACKSIDE reg=98 found max6690, loc=MLB MAX6690 AMB reg=9c PowerMac i2c bus u3 1 registered windfarm: failed to attach ds1775 hd-temp to i2c found max6690, loc=BACKSIDE reg=98 windfarm: failed to attach MAX6690 sensor found max6690, loc=MLB MAX6690 AMB reg=9c PowerMac i2c bus u3 0 registered md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 oprofile: using ppc64/970 performance monitoring. NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 3, 32768 bytes) TCP established hash table entries: 16384 (order: 7, 524288 bytes) TCP bind hash table entries: 16384 (order: 7, 524288 bytes) TCP: Hash tables configured (established 16384 bind 16384) TCP reno registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Freeing unused kernel memory: 256k freed SCSI subsystem initialized libata version 1.20 loaded. sata_svw 0001:05:0c.0: version 1.07 ata1: SATA max UDMA/133 cmd 0xD0000800872F2000 ctl 0xD0000800872F2020 bmdma 0xD0000800872F2030 irq 0 ata2: SATA max UDMA/133 cmd 0xD0000800872F2100 ctl 0xD0000800872F2120 bmdma 0xD0000800872F2130 irq 0 ata3: SATA max UDMA/133 cmd 0xD0000800872F2200 ctl 0xD0000800872F2220 bmdma 0xD0000800872F2230 irq 0 ata4: SATA max UDMA/133 cmd 0xD0000800872F2300 ctl 0xD0000800872F2320 bmdma 0xD0000800872F2330 irq 0 ata1: SATA link up 1.5 Gbps (SStatus 113) ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3469 86:3c01 87:4003 88:007f ata1: dev 0 ATA-6, max UDMA/133, 156301488 sectors: LBA48 ata1: dev 0 configured for UDMA/133 scsi0 : sata_svw ata2: SATA link up 1.5 Gbps (SStatus 113) ata2: dev 0 cfg 49:2f00 82:7c6b 83:7b09 84:4003 85:7c69 86:3a01 87:4003 88:007f ata2: dev 0 ATA-7, max UDMA/133, 156312576 sectors: LBA ata2: dev 0 configured for UDMA/133 scsi1 : sata_svw ata3: SATA link down (SStatus 4) scsi2 : sata_svw ata4: SATA link down (SStatus 4) scsi3 : sata_svw Vendor: ATA Model: ST380013AS Rev: 3.05 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9 sda10 sda11 sd 0:0:0:0: Attached scsi disk sda Vendor: ATA Model: Maxtor 6Y080M0 Rev: YAR5 Type: Direct-Access ANSI SCSI revision: 05 sd 0:0:0:0: Attached scsi generic sg0 type 0 SCSI device sdb: 156312576 512-byte hdwr sectors (80032 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 156312576 512-byte hdwr sectors (80032 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: [mac] sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8 sd 1:0:0:0: Attached scsi disk sdb sd 1:0:0:0: Attached scsi generic sg1 type 0 Adding 1048568k swap on /dev/sda3. Priority:-1 extents:1 across:1048568k Adding 1023992k swap on /dev/sdb3. Priority:-2 extents:1 across:1023992k input: PowerMac Beep as /class/input/input4 hda: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected Apple U3 chipset agpgart: configuring for size idx: 64 agpgart: AGP aperture is 256M @ 0x0 ieee1394: Initialized config rom entry `ip1394' PCI: Enabling device: (0001:03:0e.0), cmd 2 ohci1394: fw-host0: Unexpected PCI resource length of 1000! ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[40] MMIO=[80200000-802007ff] Max Packet=[4096] IR/IT contexts=[8/8] tg3.c:v3.49 (Feb 2, 2006) PCI: Enabling device: (0001:06:03.0), cmd 6 spidernet: module not supported by Novell, setting U taint flag. eth0: Tigon3 [partno(3C996B-T) rev 0105 PHY(5701)] (PCI:33MHz:64-bit) 10/100/1000BaseT Ethernet 00:04:76:f3:c2:4f eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[0] eth0: dma_rwctrl[76ff2d0f] sungem.c:v0.98 8/24/03 David S. Miller (davem@redhat.com) PHY ID: 2062e0, addr: 1 eth1: Sun GEM (PCI) 10/100/1000BaseT Ethernet 00:0a:95:a6:5d:66 eth1: Found BCM5421-K2 PHY ieee1394: Node added: ID:BUS[0-00:1023] GUID[0010b92100519fad] ieee1394: Host added: ID:BUS[0-01:1023] GUID[000a95fffea65d66] usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan - (without firmware) drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan 1 port adapter drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan 2 port adapter drivers/usb/serial/usb-serial.c: USB Serial support registered for Keyspan 4 port adapter keyspan 5-2:1.0: Keyspan 2 port adapter converter detected usb 5-2: Keyspan 2 port adapter converter now attached to ttyUSB0 usb 5-2: Keyspan 2 port adapter converter now attached to ttyUSB1 usbcore: registered new driver keyspan drivers/usb/serial/keyspan.c: v1.1.4:Keyspan USB to Serial Converter Driver eth0 renamed to ethxx0 eth1 renamed to eth0 eth0: Link is up at 100 Mbps, full-duplex. ethxx0 renamed to eth1 ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) ieee1394: sbp2: Try serialize_io=0 for better performance scsi4 : SBP-2 IEEE-1394 ieee1394: sbp2: Logged into SBP-2 device ieee1394: Node 0-00:1023: Max speed [S400] - Max payload [2048] Vendor: Maxtor Model: OneTouch II Rev: 023g Type: Direct-Access ANSI SCSI revision: 04 SCSI device sdc: 586114704 512-byte hdwr sectors (300091 MB) sdc: Write Protect is off sdc: Mode Sense: 00 32 00 00 sdc: cache data unavailable sdc: assuming drive cache: write through SCSI device sdc: 586114704 512-byte hdwr sectors (300091 MB) sdc: Write Protect is off sdc: Mode Sense: 00 32 00 00 sdc: cache data unavailable sdc: assuming drive cache: write through sdc: [mac] sdc1 sdc2 sdc3 sdc4 sdc5 sdc6 sdc7 sdc8 sd 4:0:1:0: Attached scsi disk sdc sd 4:0:1:0: Attached scsi generic sg2 type 0 device-mapper: 4.5.0-ioctl (2005-10-04) initialised: dm-devel@redhat.com dm-netlink version 0.0.2 loaded loop: loaded (max 8 devices) AppArmor: AppArmor (version 2.0-19.43r6152) initialized audit(1141052147.508:2): AppArmor (version 2.0-19.43r6152) initialized eth0: Link is up at 100 Mbps, full-duplex. eth0: Pause is enabled (rxfifo: 10240 off: 7168 on: 5632) NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver st: Version 20050830, fixed bufsize 32768, s/g segs 256 Warning: /proc/ide/hd?/settings interface is obsolete, and will be removed soon! KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_addr (isr: 04) low_i2c: Keywest got an out of state interrupt, ignoring low_i2c: Keywest got an out of state interrupt, ignoring low_i2c: Keywest got an out of state interrupt, ignoring KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) KW: wrong state. Got KW_I2C_IRQ_ADDR, state: state_stop (isr: 06) Failure writing address to FCU: -5<7>KW: wrong state. Got KW_I2C_IRQ_STOP, state: state_write (isr: 04) Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! Error -6 reading backside fan ! ----- End forwarded message -----