All of lore.kernel.org
 help / color / mirror / Atom feed
From: Pavel Machek <pavel@ucw.cz>
To: rpurdie@rpsys.net, lenz@cs.wisc.edu,
	kernel list <linux-kernel@vger.kernel.org>
Subject: [rfc] Collie battery status sensing code
Date: Thu, 9 Mar 2006 13:38:42 +0100	[thread overview]
Message-ID: <20060309123842.GA3619@elf.ucw.cz> (raw)

Hi!

This is collie battery sensing code. It differs from sharpsl code a
bit -- because it is dependend on ucb1x00, not on platform bus.

I guess I should reorganize #include's and remove #if 0-ed
code. Anything else?
							Pavel

diff --git a/arch/arm/mach-sa1100/collie_pm.c b/arch/arm/mach-sa1100/collie_pm.c
new file mode 100644
index 0000000..491d03a
--- /dev/null
+++ b/arch/arm/mach-sa1100/collie_pm.c
@@ -0,0 +1,324 @@
+/*
+ * Based on spitz_pm.c and sharp code.
+ *
+ * Copyright (C) 2001  SHARP
+ * Copyright 2005 Pavel Machek <pavel@suse.cz>
+ *
+ * Distribute under GPLv2.
+ */
+
+#include <linux/module.h>
+#include <linux/stat.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/device.h>
+#include <asm/apm.h>
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+#include <asm/hardware.h>
+#include <asm/hardware/scoop.h>
+#include <asm/dma.h>
+#include <linux/platform_device.h>
+
+#include <asm/arch/collie.h>
+#include "../mach-pxa/sharpsl.h"
+#include "../drivers/mfd/ucb1x00.h"
+#include <asm/mach/sharpsl_param.h>
+
+#ifdef CONFIG_MCP_UCB1200_TS
+#error Battery interferes with touchscreen
+#endif
+
+static struct ucb1x00 *ucb;
+
+#define ConvRevise(x)          ( ( ad_revise * x ) / 652 )
+#define ADCtoPower(x)	       (( 330 * x * 2 ) / 1024 )
+
+static int ad_revise = 0;
+
+static void collie_charger_init(void)
+{
+	int err;
+
+	/* get ad revise */
+	if (sharpsl_param.adadj != -1) {
+		ad_revise = sharpsl_param.adadj;
+	} else {
+		ad_revise = 0;
+	}
+
+	/* Register interrupt handler. */
+	if ((err = request_irq(COLLIE_IRQ_GPIO_AC_IN, sharpsl_ac_isr, SA_INTERRUPT,
+			       "ACIN", sharpsl_ac_isr))) {
+		printk("Could not get irq %d.\n", COLLIE_IRQ_GPIO_AC_IN);
+		return;
+	}
+
+	/* Register interrupt handler. */
+	if ((err = request_irq(COLLIE_IRQ_GPIO_CO, sharpsl_chrg_full_isr, SA_INTERRUPT,
+			       "CO", sharpsl_chrg_full_isr))) {
+		free_irq(COLLIE_IRQ_GPIO_AC_IN, sharpsl_ac_isr);
+		printk("Could not get irq %d.\n", COLLIE_IRQ_GPIO_CO);
+		return;
+	}
+
+	if (!ucb)
+		printk(KERN_CRIT "ucb is null!\n");
+
+	/* Set transition detect */
+	ucb1x00_enable_irq(ucb, COLLIE_GPIO_AC_IN, UCB_RISING);
+	ucb1x00_enable_irq(ucb, COLLIE_GPIO_CO, UCB_RISING);
+
+	ucb1x00_adc_enable(ucb);
+	ucb1x00_io_set_dir(ucb, 0, COLLIE_TC35143_GPIO_MBAT_ON |  COLLIE_TC35143_GPIO_TMP_ON |
+			           COLLIE_TC35143_GPIO_BBAT_ON);
+	return;
+}
+
+static void collie_charge_led(int val)
+{
+	if (val == SHARPSL_LED_ERROR) {
+		dev_dbg(sharpsl_pm.dev, "Charge LED Error\n");
+	} else if (val == SHARPSL_LED_ON) {
+		dev_dbg(sharpsl_pm.dev, "Charge LED On\n");
+	} else {
+		dev_dbg(sharpsl_pm.dev, "Charge LED Off\n");
+	}
+}
+
+static void collie_measure_temp(int on)
+{
+	if (on)
+		ucb1x00_io_write(ucb, COLLIE_TC35143_GPIO_TMP_ON, 0);
+	else
+		ucb1x00_io_write(ucb, 0, COLLIE_TC35143_GPIO_TMP_ON);
+}
+
+static void collie_charge(int on)
+{
+	if (on) {
+		printk("Should start charger\n");
+	} else {
+		printk("Should stop charger\n");
+	}
+#ifdef I_AM_SURE
+#define CF_BUF_CTRL_BASE 0xF0800000
+#define        SCOOP_REG(adr) (*(volatile unsigned short*)(CF_BUF_CTRL_BASE+(adr)))
+#define        SCOOP_REG_GPWR    SCOOP_REG(SCOOP_GPWR)
+
+	if (on) {
+		SCOOP_REG_GPWR |= COLLIE_SCP_CHARGE_ON;
+	} else {
+		SCOOP_REG_GPWR &= ~COLLIE_SCP_CHARGE_ON;
+	}
+#endif
+}
+
+static void collie_discharge(int on)
+{
+}
+
+static void collie_discharge1(int on)
+{
+}
+
+static void collie_presuspend(void)
+{
+}
+
+static void collie_postsuspend(void)
+{
+}
+
+static int collie_should_wakeup(unsigned int resume_on_alarm)
+{
+	return 0;
+}
+
+static unsigned long collie_charger_wakeup(void)
+{
+	return 0;
+}
+
+static int collie_acin_status(void)
+{
+	int ret = GPLR & COLLIE_GPIO_AC_IN;
+	printk("AC status = %d\n", ret);
+	return ret;
+}
+
+int collie_read_backup_battery(void)
+{
+	int voltage;
+
+	/* Gives 75..130 */
+	ucb1x00_io_write(ucb, COLLIE_TC35143_GPIO_BBAT_ON, 0);
+	voltage = ucb1x00_adc_read(ucb, UCB_ADC_INP_AD1, UCB_SYNC);
+
+	ucb1x00_io_write(ucb, 0, COLLIE_TC35143_GPIO_BBAT_ON);
+
+	printk("Backup battery = %d(%d)\n", ADCtoPower(voltage), voltage);
+
+	return ADCtoPower(voltage);
+}
+
+int collie_read_main_battery(void)
+{
+	int voltage;
+
+	collie_read_temp();
+	collie_read_backup_battery();
+	ucb1x00_io_write(ucb, 0, COLLIE_TC35143_GPIO_BBAT_ON);
+	ucb1x00_io_write(ucb, COLLIE_TC35143_GPIO_MBAT_ON, 0);
+	voltage = ucb1x00_adc_read(ucb, UCB_ADC_INP_AD1, UCB_SYNC);
+
+	ucb1x00_io_write(ucb, 0, COLLIE_TC35143_GPIO_MBAT_ON);
+
+	/*
+	   gives values 160..255 with battery removed... and
+	   145..255 with battery inserted. (on AC)
+
+	   On battery, it goes as low as 80.
+	*/
+
+	printk("Main battery = %d(%d)\n",ADCtoPower((voltage+ConvRevise(voltage))),voltage);
+
+	if ( voltage != -1 ) {
+		return ADCtoPower((voltage+ConvRevise(voltage)));
+	} else {
+		return voltage;
+	}
+}
+
+int collie_read_temp(void)
+{
+	int voltage;
+
+	/* temp must be > 973, main battery must be < 465 */
+	/* FIXME sharpsl_pm.c has both conditions negated? */
+
+	ucb1x00_io_write(ucb, COLLIE_TC35143_GPIO_TMP_ON, 0);
+	voltage = ucb1x00_adc_read(ucb, UCB_ADC_INP_AD0, UCB_SYNC);
+	ucb1x00_io_write(ucb, 0, COLLIE_TC35143_GPIO_TMP_ON);
+
+	/* >1010 = battery removed.
+	   460 = 22C ?
+	   higer = lower temp ?
+	*/
+
+	printk("Battery temp = %d\n", voltage);
+	return voltage;
+}
+
+static int collie_read_acin(void)
+{
+	return 0x1;
+}
+
+static unsigned long read_devdata(int which)
+{
+	switch (which) {
+	case SHARPSL_BATT_VOLT:
+		return collie_read_main_battery();
+	case SHARPSL_BATT_TEMP:
+		return collie_read_temp();
+	case SHARPSL_ACIN_VOLT:
+		return collie_read_acin();
+	case SHARPSL_STATUS_ACIN:
+	case SHARPSL_STATUS_LOCK:
+	case SHARPSL_STATUS_CHRGFULL:
+	case SHARPSL_STATUS_FATAL:
+	default:
+		return ~0;
+	}
+#if 0
+It should be okay. Nobody really needs those.
+	.gpio_batlock     = COLLIE_GPIO_BAT_COVER,
+	.gpio_acin        = COLLIE_GPIO_AC_IN,
+	.gpio_batfull     = COLLIE_GPIO_CHRG_FULL,
+	.gpio_fatal       = COLLIE_GPIO_FATAL_BAT,
+#endif
+}
+
+struct battery_thresh spitz_battery_levels_noac[] = {
+#ifdef FOO_FRONTLIGHT
+	{ 368, 100},
+	{ 358,  25},
+	{ 356,   5},
+	{   0,   0},
+#else
+	{ 378, 100},
+	{ 365,  25},
+	{ 363,   5},
+	{   0,   0},
+#endif	
+};
+
+struct battery_thresh spitz_battery_levels_acin[] = {
+#ifdef FOO_FRONTLIGHT
+	{ 368, 100},
+	{ 358,  25},
+	{ 356,   5},
+	{   0,   0},
+#else
+	{ 378, 100},
+	{ 365,  25},
+	{ 363,   5},
+	{   0,   0},
+#endif	
+};
+
+struct sharpsl_charger_machinfo collie_pm_machinfo = {
+	.init             = collie_charger_init,
+	.read_devdata	  = read_devdata,
+	.discharge        = collie_discharge,
+	.discharge1       = collie_discharge1,
+	.charge           = collie_charge,
+	.measure_temp     = collie_measure_temp,
+	.presuspend       = collie_presuspend,
+	.postsuspend      = collie_postsuspend,
+	.charger_wakeup   = collie_charger_wakeup,
+	.should_wakeup    = collie_should_wakeup,
+	.bat_levels       = 3,
+	.bat_levels_noac  = spitz_battery_levels_noac,
+	.bat_levels_acin  = spitz_battery_levels_acin,
+	.status_high_acin = 368,
+	.status_low_acin  = 358,
+	.status_high_noac = 368,
+	.status_low_noac  = 358,
+};
+
+extern struct sharpsl_pm_status sharpsl_pm;
+
+static int __init collie_pm_add(struct ucb1x00_dev *pdev)
+{
+	sharpsl_pm.dev = NULL;
+	sharpsl_pm.machinfo = &collie_pm_machinfo;
+	ucb = pdev->ucb;
+	return sharpsl_pm_init();
+}
+
+static int collie_pm_remove(struct ucb1x00_dev *pdev)
+{
+	return sharpsl_pm_done();
+}
+
+static struct ucb1x00_driver collie_pm_driver = {
+	.add            = collie_pm_add,
+        .remove         = collie_pm_remove,
+};
+
+static int __init collie_pm_init(void)
+{
+	return ucb1x00_register_driver(&collie_pm_driver);
+}
+
+static void __exit collie_pm_exit(void)
+{
+	ucb1x00_unregister_driver(&collie_pm_driver);
+}
+
+late_initcall(collie_pm_init);
+module_exit(collie_pm_exit);

-- 
Web maintainer for suspend.sf.net (www.sf.net/projects/suspend) wanted...

             reply	other threads:[~2006-03-09 12:39 UTC|newest]

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2006-03-09 12:38 Pavel Machek [this message]
2006-03-09 13:11 ` [rfc] Collie battery status sensing code Pavel Machek
2006-03-09 13:19 ` Richard Purdie
2006-03-05  0:12   ` Pavel Machek
2006-03-09 17:12     ` Richard Purdie
2006-03-10 17:50       ` Pavel Machek
2006-03-10  8:55   ` Pavel Machek

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20060309123842.GA3619@elf.ucw.cz \
    --to=pavel@ucw.cz \
    --cc=lenz@cs.wisc.edu \
    --cc=linux-kernel@vger.kernel.org \
    --cc=rpurdie@rpsys.net \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.