From: Sander <sander@humilis.net>
To: Andrew Morton <akpm@osdl.org>
Cc: linux-ide@vger.kernel.org, jgarzik@favonius.humilis.net, lkml@rtr.ca
Subject: sata_mv success on 2.6.16-rc6-mm2 (was: Re: 2.6.16-rc6-mm2)
Date: Sat, 18 Mar 2006 16:10:10 +0100 [thread overview]
Message-ID: <20060318151010.GA19568@favonius> (raw)
In-Reply-To: <20060318044056.350a2931.akpm@osdl.org>
Andrew Morton wrote (ao):
> ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.16-rc6/2.6.16-rc6-mm2/
Good news! This kernel lets me use eight Maxtor sata disks in raid5 over
nForce4 and Marvell MV88SX6081.
I do:
mdadm -C -l5 -n8 /dev/md0 /dev/sda1 /dev/sdb1 /dev/sdc1 \
/dev/sdd1 /dev/sde1 /dev/sdf1 /dev/sdg1 /dev/sdh1
mke2fs -j -m1 /dev/md0
mount -o data=writeback,nobh /dev/md0 /mnt
for i in `seq 10`
do dd if=/dev/zero of=bigfile.$i bs=1024k count=10000
done
md5sum bigfile.*
rm bigfile.*
and
for i in `seq 10`
do dd if=/dev/zero of=bigfile.$i bs=1024k count=10000 &
done
sleep 1200
md5sum bigfile.*
rm bigfile.*
and
for i in `seq 4`
do ( dd if=/dev/zero of=bigfile.$i bs=1024k count=10000 ; \
time md5sum bigfile.$i ) &
done
I experience no crash and no data corruption with these simple tests.
2.6.16-rc6 crashes with no output of the crash on netconsole (have to
find a screen to connect to the system).
2.6.16-rc3 crashes too:
http://www.ussg.iu.edu/hypermail/linux/kernel/0602.2/0360.html
I haven't tried 2.6.16-rc6-mm1.
With 2.6.16-rc6-mm2 I do get "BUG: warning ..." and "Call Trace: ..."
messages during boot (see dmesg below), which are not there with 2.6.16-rc6.
But that seems not to cause any problems.
I also see these appear during the tests:
[ 3584.499415] ata5: translated ATA stat/err 0xd0/00 to SCSI SK/ASC/ASCQ 0xb/47/00
[ 3584.499469] ata5: status=0xd0 { Busy }
[ 4430.676302] ata9: translated ATA stat/err 0xd0/00 to SCSI SK/ASC/ASCQ 0xb/47/00
[ 4430.676355] ata9: status=0xd0 { Busy }
But with no visible effect.
Thanks!
Kind regards, Sander
[ 82.078411] libata version 1.20 loaded.
[ 82.078449] sata_nv 0000:00:07.0: version 0.8
[ 82.078457] ACPI (acpi_bus-0216): Device 'SAT0' is not power manageable [20060210]
[ 82.078917] ACPI: PCI Interrupt Link [LTID] enabled at IRQ 23
[ 82.078967] GSI 20 sharing vector 0xD1 and IRQ 20
[ 82.079015] ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [LTID] -> GSI 23 (level, high) -> IRQ 20
[ 82.079376] PCI: Setting latency timer of device 0000:00:07.0 to 64
[ 82.079446] ata1: SATA max UDMA/133 cmd 0x1440 ctl 0x1436 bmdma 0x1410 irq 20
[ 82.079520] ata2: SATA max UDMA/133 cmd 0x1438 ctl 0x1432 bmdma 0x1418 irq 20
[ 82.295014] ata1: SATA link up 3.0 Gbps (SStatus 123)
[ 82.494850] ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f69 84:4773 85:7c69 86:3e01 87:4763 88:407f
[ 82.494854] ata1: dev 0 ATA-7, max UDMA/133, 976773168 sectors: LBA48
[ 82.496131] nv_sata: Primary device added
[ 82.496184] nv_sata: Primary device removed
[ 82.496228] nv_sata: Secondary device added
[ 82.496273] nv_sata: Secondary device removed
[ 82.524820] ata1: dev 0 configured for UDMA/133
[ 82.524865] scsi0 : sata_nv
[ 82.744454] ata2: SATA link down (SStatus 0)
[ 82.744500] scsi1 : sata_nv
[ 82.744637] Vendor: ATA Model: Maxtor 7H500F0 Rev: HA43
[ 82.745399] Type: Direct-Access ANSI SCSI revision: 05
[ 82.745582] ACPI (acpi_bus-0216): Device 'SAT1' is not power manageable [20060210]
[ 82.746058] ACPI: PCI Interrupt Link [LSI1] enabled at IRQ 22
[ 82.746108] GSI 21 sharing vector 0xD9 and IRQ 21
[ 82.746157] ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LSI1] -> GSI 22 (level, high) -> IRQ 21
[ 82.746485] PCI: Setting latency timer of device 0000:00:08.0 to 64
[ 82.746551] ata3: SATA max UDMA/133 cmd 0x1458 ctl 0x144E bmdma 0x1420 irq 21
[ 82.746628] ata4: SATA max UDMA/133 cmd 0x1450 ctl 0x144A bmdma 0x1428 irq 21
[ 82.964178] ata3: SATA link down (SStatus 0)
[ 82.964222] scsi2 : sata_nv
[ 83.183902] ata4: SATA link down (SStatus 0)
[ 83.183946] scsi3 : sata_nv
[ 83.184069] sata_mv 0000:0a:03.0: version 0.6
[ 83.184129] GSI 22 sharing vector 0xE1 and IRQ 22
[ 83.184174] ACPI: PCI Interrupt 0000:0a:03.0[A] -> GSI 30 (level, low) -> IRQ 22
[ 83.187740] sata_mv 0000:0a:03.0: 32 slots 8 ports SCSI mode IRQ via INTx
[ 83.187857] ata5: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000222120 bmdma 0x0 irq 22
[ 83.187951] ata6: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000224120 bmdma 0x0 irq 22
[ 83.188042] ata7: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000226120 bmdma 0x0 irq 22
[ 83.188132] ata8: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000228120 bmdma 0x0 irq 22
[ 83.188222] ata9: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000232120 bmdma 0x0 irq 22
[ 83.188314] ata10: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000234120 bmdma 0x0 irq 22
[ 83.188404] ata11: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000236120 bmdma 0x0 irq 22
[ 83.188495] ata12: SATA max UDMA/133 cmd 0x0 ctl 0xFFFFC20000238120 bmdma 0x0 irq 22
[ 83.244314] BUG: warning at drivers/scsi/sata_mv.c:1896/__msleep()
[ 83.244362]
[ 83.244362] Call Trace: <IRQ> <ffffffff80408d00>{__mv_phy_reset+242}
[ 83.244509] <ffffffff804081ec>{mv_channel_reset+133} <ffffffff80409361>{mv_interrupt+565}
[ 83.244669] <ffffffff8023bf2c>{handle_IRQ_event+41} <ffffffff8023bffa>{__do_IRQ+155}
[ 83.244828] <ffffffff8020c13b>{do_IRQ+59} <ffffffff8020834c>{default_idle+0}
[ 83.244989] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eb96d>{thread_return+86}
[ 83.245172] <ffffffff80208379>{default_idle+45} <ffffffff80208406>{cpu_idle+98}
[ 83.245329] <ffffffff807c4018>{start_secondary+1224}
[ 86.569852] ata5: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 87:4063 88:007f
[ 86.569856] ata5: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 86.570840] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 86.570902]
[ 86.570903] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 86.571046] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 86.571208] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 86.571365] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eccd2>{__reacquire_kernel_lock+39}
[ 86.571552] <ffffffff804eb9bd>{thread_return+166} <ffffffff804ebfe5>{schedule_timeout+138}
[ 86.571713] <ffffffff8022a66c>{process_timeout+0} <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 86.571878] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 86.572042] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 86.575479] <ffffffff8023c4d1>{request_irq+130} <ffffffff804049f4>{ata_device_add+1163}
[ 86.575639] <ffffffff80409a41>{mv_init_one+1547} <ffffffff8036c8b2>{pci_device_probe+221}
[ 86.575799] <ffffffff803b999d>{driver_probe_device+82} <ffffffff803b9a52>{__driver_attach+0}
[ 86.575959] <ffffffff803b9aa8>{__driver_attach+86} <ffffffff803b8f5a>{bus_for_each_dev+67}
[ 86.576121] <ffffffff803b925a>{bus_add_driver+116} <ffffffff8036c918>{pci_bus_match+0}
[ 86.576279] <ffffffff8036c418>{__pci_register_driver+85} <ffffffff8020720c>{init+455}
[ 86.576438] <ffffffff8020a6b6>{child_rip+8} <ffffffff80207045>{init+0}
[ 86.576582] <ffffffff8020a6ae>{child_rip+0}
[ 86.599812] ata5: dev 0 configured for UDMA/133
[ 86.599856] scsi4 : sata_mv
[ 89.975572] ata6: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e21 87:4663 88:007f
[ 89.975576] ata6: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 89.976575] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 89.976637]
[ 89.976638] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 89.976780] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 89.976943] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 89.977100] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eb96d>{thread_return+86}
[ 89.977287] <ffffffff804ebfe5>{schedule_timeout+138} <ffffffff8022a66c>{process_timeout+0}
[ 89.977450] <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 89.977546] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 89.977710] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 89.977871] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 89.978032] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 89.978195] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 89.978355] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 89.978514] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 89.978676] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 89.978832] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 90.005534] ata6: dev 0 configured for UDMA/133
[ 90.005579] scsi5 : sata_mv
[ 93.381295] ata7: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 87:4063 88:007f
[ 93.381299] ata7: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 93.382285] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 93.382347]
[ 93.382348] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 93.382491] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 93.382652] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 93.382810] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804ecb0e>{_spin_lock_irqsave+2}
[ 93.382996] <ffffffff8022a1d9>{lock_timer_base+27} <ffffffff8022addd>{try_to_del_timer_sync+22}
[ 93.383157] <ffffffff8022ae2c>{del_timer_sync+12} <ffffffff804ebfed>{schedule_timeout+146}
[ 93.383317] <ffffffff8022a66c>{process_timeout+0} <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 93.383480] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 93.383642] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 93.383803] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 93.383965] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 93.384125] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 93.384285] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 93.384446] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 93.384606] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 93.384762] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 93.411257] ata7: dev 0 configured for UDMA/133
[ 93.411304] scsi6 : sata_mv
[ 96.787019] ata8: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 87:4063 88:007f
[ 96.787023] ata8: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 96.788019] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 96.788081]
[ 96.788081] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 96.788224] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 96.788385] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 96.788541] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff8022a1c4>{lock_timer_base+6}
[ 96.788726] <ffffffff8022addd>{try_to_del_timer_sync+22} <ffffffff8022ae2c>{del_timer_sync+12}
[ 96.788886] <ffffffff804ebfed>{schedule_timeout+146} <ffffffff8022a66c>{process_timeout+0}
[ 96.789046] <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 96.789142] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff804ecb5d>{_spin_unlock_irqrestore+8}
[ 96.789302] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 96.789462] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 96.789625] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 96.789787] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 96.789947] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 96.790110] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 96.790270] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 96.790426] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 96.816981] ata8: dev 0 configured for UDMA/133
[ 96.817025] scsi7 : sata_mv
[ 100.192743] ata9: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e21 87:4663 88:007f
[ 100.192747] ata9: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 100.193757] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 100.193819]
[ 100.193820] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 100.193963] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 100.194124] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 100.194283] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eb973>{thread_return+92}
[ 100.194469] <ffffffff804ebfe5>{schedule_timeout+138} <ffffffff8022a66c>{process_timeout+0}
[ 100.194629] <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 100.194724] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 100.194887] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 100.195048] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 100.195208] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 100.195372] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 100.195531] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 100.195690] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 100.195853] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 100.196010] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 100.222704] ata9: dev 0 configured for UDMA/133
[ 100.222749] scsi8 : sata_mv
[ 103.598467] ata10: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4063 85:7c69 86:3e01 87:4063 88:007f
[ 103.598471] ata10: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 103.599467] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 103.599530]
[ 103.599531] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 103.599674] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 103.599834] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 103.599992] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eccd2>{__reacquire_kernel_lock+39}
[ 103.600179] <ffffffff804eb9bd>{thread_return+166} <ffffffff804ebfe5>{schedule_timeout+138}
[ 103.600340] <ffffffff8022a66c>{process_timeout+0} <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 103.600502] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 103.600666] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 103.600826] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 103.600986] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 103.601152] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 103.601314] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 103.604759] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 103.604919] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 103.605075] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 103.628428] ata10: dev 0 configured for UDMA/133
[ 103.628473] scsi9 : sata_mv
[ 106.994203] ata11: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4673 85:7c69 86:3e21 87:4663 88:007f
[ 106.994207] ata11: dev 0 ATA-7, max UDMA/133, 586114704 sectors: LBA48
[ 106.995198] BUG: warning at drivers/scsi/libata-core.c:3884/__ata_qc_complete()
[ 106.995261]
[ 106.995262] Call Trace: <IRQ> <ffffffff80401694>{__ata_qc_complete+98}
[ 106.995405] <ffffffff8040939e>{mv_interrupt+626} <ffffffff8023bf2c>{handle_IRQ_event+41}
[ 106.995565] <ffffffff8023bffa>{__do_IRQ+155} <ffffffff8020c13b>{do_IRQ+59}
[ 106.995722] <ffffffff80209d64>{ret_from_intr+0} <EOI> <ffffffff804eb917>{thread_return+0}
[ 106.995907] <ffffffff804eb9bd>{thread_return+166} <ffffffff804eb9ec>{thread_return+213}
[ 106.996069] <ffffffff804ebfe5>{schedule_timeout+138} <ffffffff8022a66c>{process_timeout+0}
[ 106.996228] <ffffffff804eaeaf>{wait_for_completion_timeout+137}
[ 106.996325] <ffffffff8021cc6f>{default_wake_function+0} <ffffffff80407402>{ata_exec_command+36}
[ 106.996486] <ffffffff804038b8>{ata_exec_internal+266} <ffffffff80404473>{ata_set_mode+667}
[ 106.996646] <ffffffff804049f4>{ata_device_add+1163} <ffffffff80409a41>{mv_init_one+1547}
[ 106.996808] <ffffffff8036c8b2>{pci_device_probe+221} <ffffffff803b999d>{driver_probe_device+82}
[ 106.996969] <ffffffff803b9a52>{__driver_attach+0} <ffffffff803b9aa8>{__driver_attach+86}
[ 106.997129] <ffffffff803b8f5a>{bus_for_each_dev+67} <ffffffff803b925a>{bus_add_driver+116}
[ 106.997291] <ffffffff8036c918>{pci_bus_match+0} <ffffffff8036c418>{__pci_register_driver+85}
[ 106.997453] <ffffffff8020720c>{init+455} <ffffffff8020a6b6>{child_rip+8}
[ 106.997611] <ffffffff80207045>{init+0} <ffffffff8020a6ae>{child_rip+0}
[ 107.024165] ata11: dev 0 configured for UDMA/133
[ 107.024210] scsi10 : sata_mv
[ 107.073907] ata12: no device found (phy stat 00000000)
[ 107.073953] scsi11 : sata_mv
[ 107.074082] Vendor: ATA Model: Maxtor 6B300S0 Rev: BANC
[ 107.074841] Type: Direct-Access ANSI SCSI revision: 05
[ 107.075044] Vendor: ATA Model: Maxtor 6L300S0 Rev: BACE
[ 107.075798] Type: Direct-Access ANSI SCSI revision: 05
[ 107.075994] Vendor: ATA Model: Maxtor 6B300S0 Rev: BANC
[ 107.076749] Type: Direct-Access ANSI SCSI revision: 05
[ 107.076944] Vendor: ATA Model: Maxtor 6B300S0 Rev: BANC
[ 107.077701] Type: Direct-Access ANSI SCSI revision: 05
[ 107.077900] Vendor: ATA Model: Maxtor 6L300S0 Rev: BACE
[ 107.078653] Type: Direct-Access ANSI SCSI revision: 05
[ 107.078857] Vendor: ATA Model: Maxtor 6B300S0 Rev: BANC
[ 107.079610] Type: Direct-Access ANSI SCSI revision: 05
[ 107.079806] Vendor: ATA Model: Maxtor 6L300S0 Rev: BACE
[ 107.080559] Type: Direct-Access ANSI SCSI revision: 05
[ 107.080785] SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
[ 107.080848] sda: Write Protect is off
[ 107.080893] sda: Mode Sense: 00 3a 00 00
[ 107.080905] SCSI device sda: drive cache: write back
[ 107.081014] SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
[ 107.081069] sda: Write Protect is off
[ 107.081112] sda: Mode Sense: 00 3a 00 00
[ 107.081124] SCSI device sda: drive cache: write back
[ 107.081170] sda: sda1
[ 107.099237] sd 0:0:0:0: Attached scsi disk sda
etc, etc.
--
Humilis IT Services and Solutions
http://www.humilis.net
next prev parent reply other threads:[~2006-03-18 15:10 UTC|newest]
Thread overview: 138+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-03-18 12:40 2.6.16-rc6-mm2 Andrew Morton
2006-03-18 15:10 ` Sander [this message]
2006-03-18 19:57 ` sata_mv success on 2.6.16-rc6-mm2 (was: Re: 2.6.16-rc6-mm2) Andrew Morton
2006-03-18 17:25 ` 2.6.16-rc6-mm2: new RDMA CM EXPORT_SYMBOL's Adrian Bunk
2006-03-19 1:44 ` Tom Tucker
2006-03-19 1:57 ` Lee Revell
2006-03-18 18:45 ` [-mm patch] drivers/edac/e752x_edac.c: make sysbus_message static Adrian Bunk
2006-03-18 18:45 ` [-mm patch] drivers/scsi/aic7xxx/aic79xx_core.c: make ahd_match_scb() static Adrian Bunk
2006-03-18 18:45 ` [-mm patch] nfs4proc.c: make _nfs4_proc_setclientid_confirm() static Adrian Bunk
2006-03-18 18:45 ` [-mm patch] net/core/scm.c: make scm_detach_fds() static Adrian Bunk
2006-03-18 20:21 ` 2.6.16-rc6-mm2 Rafael J. Wysocki
2006-03-18 20:54 ` 2.6.16-rc6-mm2 Andrew Morton
2006-03-18 21:24 ` 2.6.16-rc6-mm2 Rafael J. Wysocki
2006-03-18 21:25 ` Emulex IP over FC support shogunx
2006-03-19 23:03 ` 2.6.16-rc6-mm2 - BUG when flushing a ramdisk Neil Brown
2006-03-19 1:09 ` 2.6.16-rc6-mm2 uninitialized online_policy_cpus.bits[0] Con Kolivas
2006-03-19 1:29 ` Con Kolivas
2006-03-19 1:35 ` Andrew Morton
2006-03-19 2:37 ` Con Kolivas
2006-03-19 6:13 ` Venkatesh Pallipadi
2006-03-20 3:26 ` New Areca driver in 2.6.16-rc6-mm2 Dax Kelson
2006-03-21 23:49 ` Chris Caputo
2006-03-22 3:37 ` Matti Aarnio
2006-03-22 3:56 ` Randy.Dunlap
2006-03-22 3:56 ` Al Viro
2006-03-22 4:41 ` erich
2006-03-20 13:02 ` RAID5 grow success (was: Re: 2.6.16-rc6-mm2) Sander
2006-03-20 13:33 ` Some sata_mv error messages " Sander
2006-03-21 1:02 ` Some sata_mv error messages Jeff Garzik
2006-03-21 2:25 ` Dave Jones
2006-03-21 2:35 ` Jeff Garzik
2006-03-21 16:06 ` Peter Jones
2006-03-21 4:48 ` Mark Lord
2006-03-21 7:28 ` Sander
2006-03-21 19:33 ` Denis Leroy
2006-03-21 19:37 ` Jeff Garzik
2006-03-21 19:42 ` Mark Lord
2006-03-21 7:26 ` Sander
2006-03-21 20:27 ` 2.6.16-rc6-mm2: reiser4 BUG when unmounting fs Laurent Riffard
2006-03-21 20:38 ` Laurent Riffard
2006-03-22 7:43 ` Vladimir V. Saveliev
2006-03-22 18:38 ` Laurent Riffard
2006-03-23 17:32 ` Alexander Gran
2006-03-21 22:54 ` 2.6.16-rc6-mm2: Why is CONFIG_MIGRATION available for everyone? Adrian Bunk
2006-03-21 22:57 ` Christoph Lameter
2006-03-21 23:40 ` Christoph Lameter
2006-03-22 8:41 ` 2.6.16-rc6-mm2 J.A. Magallon
2006-03-22 8:48 ` 2.6.16-rc6-mm2 Andrew Morton
2006-03-22 10:40 ` [2.6 patch] kernel/time.c: remove unused pps_* variables Adrian Bunk
-- strict thread matches above, loose matches on Subject: below --
2006-02-01 20:03 [PATCH 0/5] Infiniband: connection abstraction Sean Hefty
2006-02-01 20:03 ` Sean Hefty
2006-02-01 20:07 ` [PATCH 1/5] " Sean Hefty
2006-02-01 20:07 ` Sean Hefty
2006-02-01 20:10 ` [PATCH 2/5] " Sean Hefty
2006-02-01 20:10 ` Sean Hefty
2006-02-01 20:15 ` [PATCH 3/5] " Sean Hefty
2006-02-01 20:15 ` Sean Hefty
2006-03-03 21:14 ` [PATCH 3/5] export of ip_dev_find as part of Infiniband " Sean Hefty
2006-03-03 21:14 ` Sean Hefty
2006-02-01 20:18 ` [PATCH 4/5] Infiniband: " Sean Hefty
2006-02-01 20:18 ` Sean Hefty
2006-02-01 20:19 ` [PATCH 5/5] " Sean Hefty
2006-02-01 20:19 ` Sean Hefty
2006-03-03 21:13 ` [PATCH 0/5] " Sean Hefty
2006-03-03 22:53 ` [openib-general] " Roland Dreier
2006-03-03 22:53 ` Roland Dreier
2006-03-06 18:59 ` [PATCH 1/6] IB: common handling for marshalling parameters to/from userspace Sean Hefty
2006-03-06 18:59 ` Sean Hefty
2006-03-19 1:19 ` 2.6.16-rc6-mm2: new RDMA CM EXPORT_SYMBOL's Andrew Morton
2006-03-19 4:11 ` Matthew Frost
2006-03-20 18:32 ` [openib-general] " Sean Hefty
2006-03-20 18:47 ` Arjan van de Ven
2006-03-20 18:47 ` Roland Dreier
2006-03-20 19:18 ` [openib-general] " Sean Hefty
2006-03-06 19:04 ` [PATCH 2/6] IB: match connection requests based on private data Sean Hefty
2006-03-06 22:05 ` [openib-general] " Sean Hefty
2006-03-06 22:05 ` Sean Hefty
2006-03-06 23:29 ` [PATCH 2/6 v2] " Sean Hefty
2006-03-06 23:29 ` Sean Hefty
2006-03-06 19:04 ` [PATCH 2/6] " Sean Hefty
2006-03-06 19:07 ` [PATCH 3/6] net/IB: export ip_dev_find Sean Hefty
2006-03-06 19:07 ` Sean Hefty
2006-03-06 21:31 ` Roland Dreier
2006-03-06 21:31 ` Roland Dreier
2006-03-06 21:42 ` David S. Miller
2006-03-06 21:42 ` David S. Miller
2006-03-06 19:10 ` [PATCH 4/6] IB: address translation to map IP to IB addresses (GIDs) Sean Hefty
2006-03-06 19:10 ` Sean Hefty
2006-03-06 23:31 ` [PATCH 4/6 v2] IB: address translation to map IP toIB " Sean Hefty
2006-03-11 1:14 ` Roland Dreier
2006-03-11 1:14 ` Roland Dreier
2006-03-11 6:10 ` Sean Hefty
2006-03-11 6:10 ` Sean Hefty
2006-03-21 20:57 ` Roland Dreier
2006-03-21 21:08 ` [openib-general] " Sean Hefty
2006-03-21 21:08 ` Sean Hefty
2006-03-21 22:39 ` [openib-general] " Roland Dreier
2006-03-21 22:39 ` Roland Dreier
2006-03-06 23:31 ` Sean Hefty
2006-03-06 19:18 ` [PATCH 5/6] IB: IP address based RDMA connection manager Sean Hefty
2006-03-06 19:18 ` Sean Hefty
2006-03-06 19:21 ` [PATCH 6/6] IB: userspace support for " Sean Hefty
2006-03-06 21:33 ` Roland Dreier
2006-03-06 21:33 ` Roland Dreier
2006-03-06 21:42 ` [openib-general] " Sean Hefty
2006-03-06 21:42 ` Sean Hefty
2006-03-06 21:58 ` [openib-general] " Roland Dreier
2006-03-06 21:58 ` Roland Dreier
2006-03-06 22:28 ` [openib-general] " David S. Miller
2006-03-06 22:28 ` David S. Miller
2006-03-06 22:32 ` [openib-general] " Roland Dreier
2006-03-06 22:32 ` Roland Dreier
2006-03-06 22:39 ` [openib-general] " David S. Miller
2006-03-06 22:39 ` David S. Miller
2006-03-06 22:41 ` [openib-general] " Roland Dreier
2006-03-06 22:41 ` Roland Dreier
2006-03-06 22:50 ` [openib-general] " David S. Miller
2006-03-06 22:50 ` David S. Miller
2006-03-06 23:40 ` [openib-general] " Roland Dreier
2006-03-06 23:40 ` Roland Dreier
2006-03-07 0:05 ` [openib-general] " Bryan O'Sullivan
2006-03-07 0:10 ` Roland Dreier
2006-03-07 0:26 ` David S. Miller
2006-03-07 0:26 ` David S. Miller
2006-03-06 21:35 ` Roland Dreier
2006-03-06 21:35 ` Roland Dreier
2006-03-06 21:43 ` [openib-general] " Sean Hefty
2006-03-06 21:43 ` Sean Hefty
2006-03-06 23:41 ` [PATCH 6/6 v2] " Sean Hefty
2006-03-22 1:40 ` Roland Dreier
2006-03-22 1:40 ` Roland Dreier
2006-03-22 8:30 ` Michael S. Tsirkin
2006-03-22 8:30 ` Michael S. Tsirkin
2006-03-22 15:18 ` Roland Dreier
2006-03-22 15:18 ` Roland Dreier
2006-03-06 23:41 ` Sean Hefty
2006-03-06 19:21 ` [PATCH 6/6] " Sean Hefty
2006-03-03 21:13 ` [PATCH 0/5] Infiniband: connection abstraction Sean Hefty
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060318151010.GA19568@favonius \
--to=sander@humilis.net \
--cc=akpm@osdl.org \
--cc=jgarzik@favonius.humilis.net \
--cc=linux-ide@vger.kernel.org \
--cc=lkml@rtr.ca \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.