From: Anton Blanchard <anton@samba.org>
To: linuxppc-dev@ozlabs.org
Cc: paulus@samba.org
Subject: [PATCH] powerpc: Remove oprofile spinlock backtrace code
Date: Mon, 27 Mar 2006 12:00:45 +1100 [thread overview]
Message-ID: <20060327010045.GD4962@krispykreme> (raw)
In-Reply-To: <20060327005701.GC4962@krispykreme>
Remove oprofile spinlock backtrace code now we have proper calltrace
support. Also make MMCRA sihv and sipr bits a variable since they may
change in future cpus. Finally, MMCRA should be a 64bit quantity.
Signed-off-by: Anton Blanchard <anton@samba.org>
---
Index: linux-2.6/arch/powerpc/oprofile/op_model_power4.c
===================================================================
--- linux-2.6.orig/arch/powerpc/oprofile/op_model_power4.c 2006-03-26 17:55:19.000000000 +1100
+++ linux-2.6/arch/powerpc/oprofile/op_model_power4.c 2006-03-26 17:55:19.000000000 +1100
@@ -25,18 +25,14 @@ static unsigned long reset_value[OP_MAX_
static int oprofile_running;
static int mmcra_has_sihv;
+/* Unfortunately these bits vary between CPUs */
+static unsigned long mmcra_sihv = MMCRA_SIHV;
+static unsigned long mmcra_sipr = MMCRA_SIPR;
/* mmcr values are set in power4_reg_setup, used in power4_cpu_setup */
static u32 mmcr0_val;
static u64 mmcr1_val;
-static u32 mmcra_val;
-
-/*
- * Since we do not have an NMI, backtracing through spinlocks is
- * only a best guess. In light of this, allow it to be disabled at
- * runtime.
- */
-static int backtrace_spinlocks;
+static u64 mmcra_val;
static void power4_reg_setup(struct op_counter_config *ctr,
struct op_system_config *sys,
@@ -63,8 +59,6 @@ static void power4_reg_setup(struct op_c
mmcr1_val = sys->mmcr1;
mmcra_val = sys->mmcra;
- backtrace_spinlocks = sys->backtrace_spinlocks;
-
for (i = 0; i < cur_cpu_spec->num_pmcs; ++i)
reset_value[i] = 0x80000000UL - ctr[i].count;
@@ -197,25 +191,6 @@ static void __attribute_used__ kernel_un
{
}
-static unsigned long check_spinlock_pc(struct pt_regs *regs,
- unsigned long profile_pc)
-{
- unsigned long pc = instruction_pointer(regs);
-
- /*
- * If both the SIAR (sampled instruction) and the perfmon exception
- * occurred in a spinlock region then we account the sample to the
- * calling function. This isnt 100% correct, we really need soft
- * IRQ disable so we always get the perfmon exception at the
- * point at which the SIAR is set.
- */
- if (backtrace_spinlocks && in_lock_functions(pc) &&
- in_lock_functions(profile_pc))
- return regs->link;
- else
- return profile_pc;
-}
-
/*
* On GQ and newer the MMCRA stores the HV and PR bits at the time
* the SIAR was sampled. We use that to work out if the SIAR was sampled in
@@ -228,17 +203,17 @@ static unsigned long get_pc(struct pt_re
/* Cant do much about it */
if (!mmcra_has_sihv)
- return check_spinlock_pc(regs, pc);
+ return pc;
mmcra = mfspr(SPRN_MMCRA);
/* Were we in the hypervisor? */
- if (firmware_has_feature(FW_FEATURE_LPAR) && (mmcra & MMCRA_SIHV))
+ if (firmware_has_feature(FW_FEATURE_LPAR) && (mmcra & mmcra_sihv))
/* function descriptor madness */
return *((unsigned long *)hypervisor_bucket);
/* We were in userspace, nothing to do */
- if (mmcra & MMCRA_SIPR)
+ if (mmcra & mmcra_sipr)
return pc;
#ifdef CONFIG_PPC_RTAS
@@ -257,7 +232,7 @@ static unsigned long get_pc(struct pt_re
/* function descriptor madness */
return *((unsigned long *)kernel_unknown_bucket);
- return check_spinlock_pc(regs, pc);
+ return pc;
}
static int get_kernel(unsigned long pc)
@@ -268,7 +243,7 @@ static int get_kernel(unsigned long pc)
is_kernel = is_kernel_addr(pc);
} else {
unsigned long mmcra = mfspr(SPRN_MMCRA);
- is_kernel = ((mmcra & MMCRA_SIPR) == 0);
+ is_kernel = ((mmcra & mmcra_sipr) == 0);
}
return is_kernel;
Index: linux-2.6/arch/powerpc/oprofile/common.c
===================================================================
--- linux-2.6.orig/arch/powerpc/oprofile/common.c 2006-03-26 17:55:19.000000000 +1100
+++ linux-2.6/arch/powerpc/oprofile/common.c 2006-03-26 17:55:19.000000000 +1100
@@ -117,17 +117,10 @@ static int op_powerpc_create_files(struc
oprofilefs_create_ulong(sb, root, "enable_kernel", &sys.enable_kernel);
oprofilefs_create_ulong(sb, root, "enable_user", &sys.enable_user);
-#ifdef CONFIG_PPC64
- oprofilefs_create_ulong(sb, root, "backtrace_spinlocks",
- &sys.backtrace_spinlocks);
-#endif
/* Default to tracing both kernel and user */
sys.enable_kernel = 1;
sys.enable_user = 1;
-#ifdef CONFIG_PPC64
- sys.backtrace_spinlocks = 0;
-#endif
return 0;
}
Index: linux-2.6/include/asm-powerpc/oprofile_impl.h
===================================================================
--- linux-2.6.orig/include/asm-powerpc/oprofile_impl.h 2006-03-26 17:55:19.000000000 +1100
+++ linux-2.6/include/asm-powerpc/oprofile_impl.h 2006-03-26 17:55:19.000000000 +1100
@@ -35,9 +35,6 @@ struct op_system_config {
#endif
unsigned long enable_kernel;
unsigned long enable_user;
-#ifdef CONFIG_PPC64
- unsigned long backtrace_spinlocks;
-#endif
};
/* Per-arch configuration */
next prev parent reply other threads:[~2006-03-27 1:00 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-03-27 0:23 [PATCH] powerpc: Remove some ifdefs in oprofile_impl.h Anton Blanchard
2006-03-27 0:46 ` [PATCH] powerpc: export validate_sp for oprofile calltrace Anton Blanchard
2006-03-27 0:57 ` [PATCH] powerpc: Add oprofile calltrace support Anton Blanchard
2006-03-27 1:00 ` Anton Blanchard [this message]
2006-03-27 1:03 ` [PATCH] powerpc: Add oprofile calltrace support to all powerpc cpus Anton Blanchard
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060327010045.GD4962@krispykreme \
--to=anton@samba.org \
--cc=linuxppc-dev@ozlabs.org \
--cc=paulus@samba.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.