From: Bernhard Rosenkraenzer <bero@arklinux.org>
To: linux-kernel@vger.kernel.org
Subject: USB 2.0 CF card reader gets reset+offlined immediately with 2.6.16
Date: Thu, 6 Apr 2006 00:12:04 +0200 [thread overview]
Message-ID: <200604060012.04300.bero@arklinux.org> (raw)
Attempting to use a USB 2.0 CF card reader in 2.6.16 and 2.6.16-mm2 (known to
work back in 2.4 days, unused since) results in this:
usb 1-6: new high speed USB device using ehci_hcd and address 2
usb 1-6: new device found, idVendor=0dda, idProduct=2005
usb 1-6: new device strings: Mfr=3, Product=4, SerialNumber=5
usb 1-6: Product: Card Reader
usb 1-6: Manufacturer: Hama
usb 1-6: SerialNumber: 000000000013
usb 1-6: configuration #1 chosen from 1 choice
usbcore: registered new driver libusual
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
Vendor: Hama Model: CF Card Reader Rev: 9317
Type: Direct-Access ANSI SCSI revision: 00
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
sd 0:0:0:0: scsi: Device offlined - not ready after error recovery
sd 0:0:0:0: rejecting I/O to offline device
sd 0:0:0:0: rejecting I/O to offline device
sd 0:0:0:0: rejecting I/O to offline device
sda : READ CAPACITY failed.
sda : status=0, message=00, host=1, driver=00
sda : sense not available.
sd 0:0:0:0: rejecting I/O to offline device
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
sd 0:0:0:0: Attached scsi removable disk sda
Vendor: Hama Model: SM Card Reader Rev: 9317
Type: Direct-Access ANSI SCSI revision: 00
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
sd 0:0:0:1: scsi: Device offlined - not ready after error recovery
sd 0:0:0:1: rejecting I/O to offline device
sd 0:0:0:1: rejecting I/O to offline device
sd 0:0:0:1: rejecting I/O to offline device
sdb : READ CAPACITY failed.
sdb : status=0, message=00, host=1, driver=00
sdb : sense not available.
sd 0:0:0:1: rejecting I/O to offline device
sdb: Write Protect is off
sdb: Mode Sense: 00 00 00 00
sdb: assuming drive cache: write through
sd 0:0:0:1: Attached scsi removable disk sdb
usb 1-6: reset high speed USB device using ehci_hcd and address 2
Vendor: Hama Model: SD Card Reader Rev: 9317
Type: Direct-Access ANSI SCSI revision: 00
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
sd 0:0:0:2: scsi: Device offlined - not ready after error recovery
sd 0:0:0:2: rejecting I/O to offline device
sd 0:0:0:2: rejecting I/O to offline device
sd 0:0:0:2: rejecting I/O to offline device
sdc : READ CAPACITY failed.
sdc : status=0, message=00, host=1, driver=00
sdc : sense not available.
sd 0:0:0:2: rejecting I/O to offline device
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
sd 0:0:0:2: Attached scsi removable disk sdc
usb 1-6: reset high speed USB device using ehci_hcd and address 2
Vendor: Hama Model: MS Card Reader Rev: 9317
Type: Direct-Access ANSI SCSI revision: 00
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
usb 1-6: reset high speed USB device using ehci_hcd and address 2
sd 0:0:0:3: scsi: Device offlined - not ready after error recovery
sd 0:0:0:3: rejecting I/O to offline device
sd 0:0:0:3: rejecting I/O to offline device
sd 0:0:0:3: rejecting I/O to offline device
sdd : READ CAPACITY failed.
sdd : status=0, message=00, host=1, driver=00
sdd : sense not available.
sd 0:0:0:3: rejecting I/O to offline device
sdd: Write Protect is off
sdd: Mode Sense: 00 00 00 00
sdd: assuming drive cache: write through
sd 0:0:0:3: Attached scsi removable disk sdd
usb-storage: device scan complete
Any attempt to access the devices afterwards results in ENXIO (but
the /sys/block entries for sda to sdd remain there).
next reply other threads:[~2006-04-05 22:19 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-04-05 22:12 Bernhard Rosenkraenzer [this message]
2006-04-06 0:59 ` USB 2.0 CF card reader gets reset+offlined immediately with 2.6.16 Greg KH
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200604060012.04300.bero@arklinux.org \
--to=bero@arklinux.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.