From: Greg KH <greg@kroah.com>
To: Bernhard Rosenkraenzer <bero@arklinux.org>,
linux-usb-devel@lists.sourceforge.net
Cc: linux-kernel@vger.kernel.org
Subject: Re: USB 2.0 CF card reader gets reset+offlined immediately with 2.6.16
Date: Wed, 5 Apr 2006 17:59:10 -0700 [thread overview]
Message-ID: <20060406005910.GA18567@kroah.com> (raw)
In-Reply-To: <200604060012.04300.bero@arklinux.org>
On Thu, Apr 06, 2006 at 12:12:04AM +0200, Bernhard Rosenkraenzer wrote:
> Attempting to use a USB 2.0 CF card reader in 2.6.16 and 2.6.16-mm2 (known to
> work back in 2.4 days, unused since) results in this:
Can you enable CONFIG_USB_STORAGE_DEBUG and send the kernel log file to
the linux-usb-devel mailing list so the people there can help you out?
thanks,
greg k-h
<linux-usb-devel people, here's the original log>
> usb 1-6: new high speed USB device using ehci_hcd and address 2
> usb 1-6: new device found, idVendor=0dda, idProduct=2005
> usb 1-6: new device strings: Mfr=3, Product=4, SerialNumber=5
> usb 1-6: Product: Card Reader
> usb 1-6: Manufacturer: Hama
> usb 1-6: SerialNumber: 000000000013
> usb 1-6: configuration #1 chosen from 1 choice
> usbcore: registered new driver libusual
> Initializing USB Mass Storage driver...
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new driver usb-storage
> USB Mass Storage support registered.
> usb-storage: device found at 2
> usb-storage: waiting for device to settle before scanning
> Vendor: Hama Model: CF Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:0: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:0: rejecting I/O to offline device
> sd 0:0:0:0: rejecting I/O to offline device
> sd 0:0:0:0: rejecting I/O to offline device
> sda : READ CAPACITY failed.
> sda : status=0, message=00, host=1, driver=00
> sda : sense not available.
> sd 0:0:0:0: rejecting I/O to offline device
> sda: Write Protect is off
> sda: Mode Sense: 00 00 00 00
> sda: assuming drive cache: write through
> sd 0:0:0:0: Attached scsi removable disk sda
> Vendor: Hama Model: SM Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:1: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:1: rejecting I/O to offline device
> sd 0:0:0:1: rejecting I/O to offline device
> sd 0:0:0:1: rejecting I/O to offline device
> sdb : READ CAPACITY failed.
> sdb : status=0, message=00, host=1, driver=00
> sdb : sense not available.
> sd 0:0:0:1: rejecting I/O to offline device
> sdb: Write Protect is off
> sdb: Mode Sense: 00 00 00 00
> sdb: assuming drive cache: write through
> sd 0:0:0:1: Attached scsi removable disk sdb
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> Vendor: Hama Model: SD Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:2: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:2: rejecting I/O to offline device
> sd 0:0:0:2: rejecting I/O to offline device
> sd 0:0:0:2: rejecting I/O to offline device
> sdc : READ CAPACITY failed.
> sdc : status=0, message=00, host=1, driver=00
> sdc : sense not available.
> sd 0:0:0:2: rejecting I/O to offline device
> sdc: Write Protect is off
> sdc: Mode Sense: 00 00 00 00
> sdc: assuming drive cache: write through
> sd 0:0:0:2: Attached scsi removable disk sdc
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> Vendor: Hama Model: MS Card Reader Rev: 9317
> Type: Direct-Access ANSI SCSI revision: 00
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> usb 1-6: reset high speed USB device using ehci_hcd and address 2
> sd 0:0:0:3: scsi: Device offlined - not ready after error recovery
> sd 0:0:0:3: rejecting I/O to offline device
> sd 0:0:0:3: rejecting I/O to offline device
> sd 0:0:0:3: rejecting I/O to offline device
> sdd : READ CAPACITY failed.
> sdd : status=0, message=00, host=1, driver=00
> sdd : sense not available.
> sd 0:0:0:3: rejecting I/O to offline device
> sdd: Write Protect is off
> sdd: Mode Sense: 00 00 00 00
> sdd: assuming drive cache: write through
> sd 0:0:0:3: Attached scsi removable disk sdd
> usb-storage: device scan complete
>
>
> Any attempt to access the devices afterwards results in ENXIO (but
> the /sys/block entries for sda to sdd remain there).
prev parent reply other threads:[~2006-04-06 0:59 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-04-05 22:12 USB 2.0 CF card reader gets reset+offlined immediately with 2.6.16 Bernhard Rosenkraenzer
2006-04-06 0:59 ` Greg KH [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060406005910.GA18567@kroah.com \
--to=greg@kroah.com \
--cc=bero@arklinux.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb-devel@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.