From: masouds@masoud.ir
To: cw@f00f.org
Cc: jeff@garzik.org, gregkh@suse.de, linux-kernel@vger.kernel.org
Subject: [BUG] VIA quirk fixup failure after 2.6.17-rc3
Date: Sun, 30 Apr 2006 09:28:20 -0700 [thread overview]
Message-ID: <20060430162820.GA18666@masoud.ir> (raw)
Hello Chris,
My machine's tulip card stopped working after I updated to 2.6.17-rc3.git3 which included 75cf7456dd87335f574dcd53c4ae616a2ad71a11 patch of yours. Revesing it made the problem go away; Is there a chance that a VIA pci_id was missed from the list of quirks in your patch?
The problem was that bringing up this interface always failed with 'IRQ #177: nobody cared!':
---
Apr 30 08:44:54 localhost kernel: irq 177: nobody cared (try booting with the "irqpoll" option)
Apr 30 08:44:54 localhost kernel: <c10500f4> __report_bad_irq+0x24/0x90 <c10501df> note_interrupt+0x7f/0x240
Apr 30 08:44:54 localhost kernel: <c1022add> rebalance_tick+0x10d/0x2d0 <c104f9f3> handle_IRQ_event+0x33/0x70
Apr 30 08:44:54 localhost kernel: <c104fb22> __do_IRQ+0xf2/0x100 <c1007553> do_IRQ+0x23/0x40
Apr 30 08:44:54 localhost kernel: <c1003d10> default_idle+0x0/0x60 <c1005bf6> common_interrupt+0x1a/0x20
Apr 30 08:44:54 localhost kernel: <c1003d10> default_idle+0x0/0x60 <c1003d3c> default_idle+0x2c/0x60
Apr 30 08:44:54 localhost kernel: <c1003dcf> cpu_idle+0x5f/0xf0
Apr 30 08:44:54 localhost kernel: handlers:
Apr 30 08:44:54 localhost kernel: [pg0+392112128/1051796480] (tulip_interrupt+0x0/0xee0 [tulip])
Apr 30 08:44:54 localhost kernel: Disabling IRQ #177
Apr 30 08:45:04 localhost kernel: eth0: no IPv6 routers present
Apr 30 08:48:21 localhost kernel: NETDEV WATCHDOG: eth0: transmit timed out
Apr 30 08:48:21 localhost kernel: eth0: Transmit timed out, status e4670045, CSR12 45e1d0cc, resetting...
----
Manually removing that patch made things work again.
The machine is a MSI-694D2-Pro2 dual CPU P3/866Mhz machine with 384 megs of ram.
For more info, here is my 'lspci -vv' output:
0000:00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d0000000-d1ffffff
Prefetchable memory behind bridge: d2000000-d2ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at 9000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at 9400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at 9800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:07.4 Host bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 11
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0c.0 RAID bus controller: Promise Technology, Inc. PDC20265 (FastTrak100 Lite/Ultra100) (rev 02)
Subsystem: Promise Technology, Inc. Ultra100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at ac00 [size=8]
Region 1: I/O ports at b000 [size=4]
Region 2: I/O ports at b400 [size=8]
Region 3: I/O ports at b800 [size=4]
Region 4: I/O ports at bc00 [size=64]
Region 5: Memory at d4000000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at 20040000 [disabled] [size=64K]
Capabilities: [58] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0f.0 Ethernet controller: Macronix, Inc. [MXIC] MX987x5 (rev 25)
Subsystem: National Datacomm Corp: Unknown device 8110
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at c000 [size=256]
Region 1: Memory at d4020000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 20000000 [disabled] [size=256K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:10.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev 43)
Subsystem: D-Link System Inc DFE-530TX rev A
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at c400 [size=256]
Region 1: Memory at d4021000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at 20050000 [disabled] [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:01:00.0 VGA compatible controller: Intel Corp. 82740 (i740) AGP Graphics Accelerator (rev 21) (prog-if 00 [VGA])
Subsystem: Diamond Multimedia Systems Stealth II G460
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at d2000000 (32-bit, prefetchable) [size=16M]
Region 1: Memory at d1000000 (32-bit, non-prefetchable) [size=512K]
Expansion ROM at d0000000 [disabled] [size=256K]
Capabilities: [d0] AGP version 1.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
-------------
cheers,
Masoud Sharbiani
next reply other threads:[~2006-04-30 16:33 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-04-30 16:28 masouds [this message]
2006-05-01 0:01 ` [BUG] VIA quirk fixup failure after 2.6.17-rc3 Chris Wedgwood
2006-05-09 19:14 ` [PATCH] VIA quirk fixup, additional PCI IDs Chris Wedgwood
2006-05-09 19:59 ` Andrew Morton
2006-05-09 20:14 ` Dave Jones
2006-05-09 20:41 ` Andrew Morton
2006-05-09 20:46 ` Chris Wedgwood
2006-05-09 20:24 ` Chris Wedgwood
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060430162820.GA18666@masoud.ir \
--to=masouds@masoud.ir \
--cc=cw@f00f.org \
--cc=gregkh@suse.de \
--cc=jeff@garzik.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.