From: Rodolfo Giometti <giometti@linux.it>
To: linux-mips@linux-mips.org
Subject: au1x00 UARTs power management
Date: Tue, 27 Jun 2006 17:57:16 +0200 [thread overview]
Message-ID: <20060627155716.GC10595@enneenne.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 362 bytes --]
Hello,
the attached patch adds support for power management for UART
interfaces.
Ciao,
Rodolfo
--
GNU/Linux Solutions e-mail: giometti@enneenne.com
Linux Device Driver giometti@gnudd.com
Embedded Systems giometti@linux.it
UNIX programming phone: +39 349 2432127
[-- Attachment #2: patch-UARTs-pm-support --]
[-- Type: text/plain, Size: 5090 bytes --]
diff --git a/arch/mips/au1000/common/power.c b/arch/mips/au1000/common/power.c
index 482de93..30bfccf 100644
--- a/arch/mips/au1000/common/power.c
+++ b/arch/mips/au1000/common/power.c
@@ -92,11 +92,13 @@ static uint sleep_gpio2_dir;
static uint sleep_gpio2_output;
static uint sleep_gpio2_enable;
static uint sleep_gpio2_inten;
-static uint sleep_uart0_inten;
-static uint sleep_uart0_fifoctl;
-static uint sleep_uart0_linectl;
-static uint sleep_uart0_clkdiv;
-static uint sleep_uart0_enable;
+static struct sleep_uart_s {
+ uint inten;
+ uint fifoctl;
+ uint linectl;
+ uint clkdiv;
+ uint enable;
+} sleep_uart[4];
static uint sleep_usbhost_enable;
static uint sleep_usbdev_enable;
static uint sleep_static_memctlr[4][3];
@@ -152,11 +154,34 @@ save_core_regs(void)
* standard serial driver doesn't understand our Au1xxx
* unique registers.
*/
- sleep_uart0_inten = au_readl(UART0_ADDR + UART_IER);
- sleep_uart0_fifoctl = au_readl(UART0_ADDR + UART_FCR);
- sleep_uart0_linectl = au_readl(UART0_ADDR + UART_LCR);
- sleep_uart0_clkdiv = au_readl(UART0_ADDR + UART_CLK);
- sleep_uart0_enable = au_readl(UART0_ADDR + UART_MOD_CNTRL);
+#ifdef UART0_ADDR
+ sleep_uart[0].inten = au_readl(UART0_ADDR + UART_IER);
+ sleep_uart[0].fifoctl = au_readl(UART0_ADDR + UART_FCR);
+ sleep_uart[0].linectl = au_readl(UART0_ADDR + UART_LCR);
+ sleep_uart[0].clkdiv = au_readl(UART0_ADDR + UART_CLK);
+ sleep_uart[0].enable = au_readl(UART0_ADDR + UART_MOD_CNTRL);
+#endif
+#ifdef UART1_ADDR
+ sleep_uart[1].inten = au_readl(UART1_ADDR + UART_IER);
+ sleep_uart[1].fifoctl = au_readl(UART1_ADDR + UART_FCR);
+ sleep_uart[1].linectl = au_readl(UART1_ADDR + UART_LCR);
+ sleep_uart[1].clkdiv = au_readl(UART1_ADDR + UART_CLK);
+ sleep_uart[1].enable = au_readl(UART1_ADDR + UART_MOD_CNTRL);
+#endif
+#ifdef UART2_ADDR
+ sleep_uart[2].inten = au_readl(UART2_ADDR + UART_IER);
+ sleep_uart[2].fifoctl = au_readl(UART2_ADDR + UART_FCR);
+ sleep_uart[2].linectl = au_readl(UART2_ADDR + UART_LCR);
+ sleep_uart[2].clkdiv = au_readl(UART2_ADDR + UART_CLK);
+ sleep_uart[2].enable = au_readl(UART2_ADDR + UART_MOD_CNTRL);
+#endif
+#ifdef UART3_ADDR
+ sleep_uart[3].inten = au_readl(UART3_ADDR + UART_IER);
+ sleep_uart[3].fifoctl = au_readl(UART3_ADDR + UART_FCR);
+ sleep_uart[3].linectl = au_readl(UART3_ADDR + UART_LCR);
+ sleep_uart[3].clkdiv = au_readl(UART3_ADDR + UART_CLK);
+ sleep_uart[3].enable = au_readl(UART3_ADDR + UART_MOD_CNTRL);
+#endif
/* Shutdown USB host/device.
*/
@@ -240,15 +265,50 @@ restore_core_regs(void)
/* Enable the UART if it was enabled before sleep.
* I guess I should define module control bits........
*/
- if (sleep_uart0_enable & 0x02) {
+#ifdef UART0_ADDR
+ if (sleep_uart[0].enable & 0x02) {
au_writel(0, UART0_ADDR + UART_MOD_CNTRL); au_sync();
au_writel(1, UART0_ADDR + UART_MOD_CNTRL); au_sync();
au_writel(3, UART0_ADDR + UART_MOD_CNTRL); au_sync();
- au_writel(sleep_uart0_inten, UART0_ADDR + UART_IER); au_sync();
- au_writel(sleep_uart0_fifoctl, UART0_ADDR + UART_FCR); au_sync();
- au_writel(sleep_uart0_linectl, UART0_ADDR + UART_LCR); au_sync();
- au_writel(sleep_uart0_clkdiv, UART0_ADDR + UART_CLK); au_sync();
+ au_writel(sleep_uart[0].inten, UART0_ADDR + UART_IER); au_sync();
+ au_writel(sleep_uart[0].fifoctl, UART0_ADDR + UART_FCR); au_sync();
+ au_writel(sleep_uart[0].linectl, UART0_ADDR + UART_LCR); au_sync();
+ au_writel(sleep_uart[0].clkdiv, UART0_ADDR + UART_CLK); au_sync();
+ }
+#endif
+#ifdef UART1_ADDR
+ if (sleep_uart[1].enable & 0x02) {
+ au_writel(0, UART1_ADDR + UART_MOD_CNTRL); au_sync();
+ au_writel(1, UART1_ADDR + UART_MOD_CNTRL); au_sync();
+ au_writel(3, UART1_ADDR + UART_MOD_CNTRL); au_sync();
+ au_writel(sleep_uart[1].inten, UART1_ADDR + UART_IER); au_sync();
+ au_writel(sleep_uart[1].fifoctl, UART1_ADDR + UART_FCR); au_sync();
+ au_writel(sleep_uart[1].linectl, UART1_ADDR + UART_LCR); au_sync();
+ au_writel(sleep_uart[1].clkdiv, UART1_ADDR + UART_CLK); au_sync();
}
+#endif
+#ifdef UART2_ADDR
+ if (sleep_uart[2].enable & 0x02) {
+ au_writel(0, UART2_ADDR + UART_MOD_CNTRL); au_sync();
+ au_writel(1, UART2_ADDR + UART_MOD_CNTRL); au_sync();
+ au_writel(3, UART2_ADDR + UART_MOD_CNTRL); au_sync();
+ au_writel(sleep_uart[2].inten, UART2_ADDR + UART_IER); au_sync();
+ au_writel(sleep_uart[2].fifoctl, UART2_ADDR + UART_FCR); au_sync();
+ au_writel(sleep_uart[2].linectl, UART2_ADDR + UART_LCR); au_sync();
+ au_writel(sleep_uart[2].clkdiv, UART2_ADDR + UART_CLK); au_sync();
+ }
+#endif
+#ifdef UART3_ADDR
+ if (sleep_uart[3].enable & 0x02) {
+ au_writel(0, UART3_ADDR + UART_MOD_CNTRL); au_sync();
+ au_writel(1, UART3_ADDR + UART_MOD_CNTRL); au_sync();
+ au_writel(3, UART3_ADDR + UART_MOD_CNTRL); au_sync();
+ au_writel(sleep_uart[3].inten, UART3_ADDR + UART_IER); au_sync();
+ au_writel(sleep_uart[3].fifoctl, UART3_ADDR + UART_FCR); au_sync();
+ au_writel(sleep_uart[3].linectl, UART3_ADDR + UART_LCR); au_sync();
+ au_writel(sleep_uart[3].clkdiv, UART3_ADDR + UART_CLK); au_sync();
+ }
+#endif
restore_au1xxx_intctl();
wakeup_counter0_adjust();
reply other threads:[~2006-06-27 15:57 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20060627155716.GC10595@enneenne.com \
--to=giometti@linux.it \
--cc=linux-mips@linux-mips.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.