From: "tony" <hangtoo@163.com>
To: "linuxppc-embedded@ozlabs.org" <linuxppc-embedded@ozlabs.org>
Subject: pci-usb card problem
Date: Mon, 16 Oct 2006 17:51:33 +0800 [thread overview]
Message-ID: <200610161751272186329@163.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 3513 bytes --]
hi,all
I got a pci to usb card problem this days.
env: linux-2.6.17,ppc405ep,bubinga board
problem:
during boot time,an error show up like this
Scanning device for bad blocks
Creating 1 MTD partitions on "NAND 8MiB 1,8V 8-bit":
0x00000000-0x00800000 : "NAND simulator partition"
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 29, io mem 0xbfffff00
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17-rc3 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v3.0
uhci_hcd 0000:00:02.0: UHCI Host Controller
uhci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:02.0: detected 2 ports
uhci_hcd 0000:00:02.0: irq 29, io base 0x0000ffe0
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.17-rc3 uhci_hcd
usb usb2: SerialNumber: 0000:00:02.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:02.1: UHCI Host Controller
uhci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:02.1: detected 2 ports
uhci_hcd 0000:00:02.1: irq 29, io base 0x0000ffc0
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.17-rc3 uhci_hcd
usb usb3: SerialNumber: 0000:00:02.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usb 1-3: new high speed USB device using ehci_hcd and address 2
usb 1-3: configuration #1 chosen from 1 choice
ub(1.2): GetMaxLUN returned 0, using 1 LUNs
Oops: kernel access of bad area, sig: 11 [#1]
NIP: 00000000 LR: C0170314 CTR: 00000000
REGS: c030bd40 TRAP: 0400 Not tainted (2.6.17-rc3)
MSR: 00021030 <ME,IR,DR> CR: 42004024 XER: 20000000
TASK = c02c78f8[0] 'swapper' THREAD: c030a000
GPR00: 00000000 C030BDF0 C02C78F8 C75CE800 C75D0A00 00000000 00000008 00000008
GPR08: 00000001 00000000 C75D0A00 C75CE854 22004082 00000000 07FF7F00 00000000
GPR16: 00000001 00000001 FFFFFFFF 007FFF00 07FF2B4C 00000000 C75CE9D4 C016F5C0
GPR24: 00029030 00000000 C75CE960 C75CE9F4 C75CE978 C0330000 00000000 C75CE800
Call Trace:
[C030BDF0] [C0330000] (unreliable)
[C030BE10] [C01704C8]
[C030BE40] [C001F734]
[C030BE60] [C001F908]
[C030BE90] [C0007CC0]
[C030BEA0] [C001F638]
[C030BEB0] [C0007C1C]
[C030BED0] [C00032F8]
[C030BF90] [C000A6B0]
[C030BFB0] [C0002358]
[C030BFC0] [C030C694]
[C030BFF0] [C0002254]
Instruction dump:
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX XXXXXXXX
Kernel panic - not syncing: Aiee, killing interrupt handler!
<0>Rebooting in 1 seconds..
rarely,it can boot successfully,shows:
Initializing USB Mass Storage driver...
usb 1-3: new high speed USB device using ehci_hcd and address 2
usb 1-3: Product: USBFlash
usb 1-3: Manufacturer: Generic
usb 1-3: configuration #1 chosen from 1 choice
ub(1.2): Unable to submit GetMaxLUN (-22)
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
TCP bic registered
I have tried to configure kernel many times...but the problem still exists....
any advise is appreciated.
tony
[-- Attachment #2: Type: text/html, Size: 4348 bytes --]
reply other threads:[~2006-10-16 10:06 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=200610161751272186329@163.com \
--to=hangtoo@163.com \
--cc=linuxppc-embedded@ozlabs.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.