From: Stephen Hemminger <shemminger@osdl.org>
To: Jeff Garzik <jgarzik@pobox.com>
Cc: linux-ide@vger.kernel.org
Subject: Slow SATA detection on bootup
Date: Wed, 25 Oct 2006 11:45:04 -0700 [thread overview]
Message-ID: <20061025114504.450b3425@localhost> (raw)
This laptop has long timeouts during bootup. Something is
wrong. This is a Sony VAIO NG170. On a positive note suspend works.
Here is the console log during the 40 seconds of dead time.
[ 2.942000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.942000] ata1: SATA max UDMA/133 cmd 0x18B0 ctl 0x18A6 bmdma 0x1890 irq 225
[ 2.942000] ata2: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 225
[ 2.942000] scsi0 : ata_piix
[ 3.094000] ata1.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32)
[ 3.094000] ata1.00: ata1: dev 0 multi count 16
[ 3.097000] ata1.00: configured for UDMA/100
[ 3.097000] scsi1 : ata_piix
[ 10.144000] ata2: port is slow to respond, please be patient
[ 33.104000] ata2: port failed to respond (30 secs)
[ 33.255000] ata2: SRST failed (status 0xFF)
[ 33.255000] ata2: SRST failed (err_mask=0x100)
[ 33.255000] ata2: softreset failed, retrying in 5 secs
[ 38.407000] ata2: SRST failed (status 0xFF)
[ 38.407000] ata2: SRST failed (err_mask=0x100)
[ 38.407000] ata2: softreset failed, retrying in 5 secs
[ 43.560000] ata2: SRST failed (status 0xFF)
[ 43.560000] ata2: SRST failed (err_mask=0x100)
[ 43.560000] ata2: reset failed, giving up
[ 43.560000] Vendor: ATA Model: FUJITSU MHV2120B Rev: 0000
[ 43.561000] Type: Direct-Access ANSI SCSI revision: 05
[ 43.567000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
Full log:
[ 0.000000] Linux version 2.6.18.1 (shemminger@sony-laptop) (gcc version 4.0.3 (Ubuntu 4.0.3-1ubuntu5)) #1 SMP PREEMPT Fri Oct 20 15:14:44 PDT 2006
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
[ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f690000 (usable)
[ 0.000000] BIOS-e820: 000000003f690000 - 000000003f698000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003f698000 - 000000003f700000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f700000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
[ 0.000000] Warning only 896MB will be used.
[ 0.000000] Use a HIGHMEM enabled kernel.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000f71b0
[ 0.000000] On node 0 totalpages: 229376
[ 0.000000] DMA zone: 4096 pages, LIFO batch:0
[ 0.000000] Normal zone: 225280 pages, LIFO batch:31
[ 0.000000] DMI present.
[ 0.000000] ACPI: RSDP (v000 PTLTD ) @ 0x000f70e0
[ 0.000000] ACPI: RSDT (v001 SONY J4 0x20060907 PTL 0x00000000) @ 0x3f6916ca
[ 0.000000] ACPI: FADT (v002 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697e48
[ 0.000000] ACPI: MADT (v001 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697ecc
[ 0.000000] ACPI: MCFG (v001 SONY J4 0x20060907 PTL 0x0000005a) @ 0x3f697f34
[ 0.000000] ACPI: MADT (v001 SONY J4 0x20060907 PTL 0x00000000) @ 0x3f697f70
[ 0.000000] ACPI: BOOT (v001 SONY J4 0x20060907 PTL 0x00000001) @ 0x3f697fd8
[ 0.000000] ACPI: SSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x3f69210b
[ 0.000000] ACPI: SSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x3f69170a
[ 0.000000] ACPI: DSDT (v001 SONY J4 0x20060907 PTL 0x20050624) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: 2 duplicate APIC table ignored.
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:14 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 6:14 APIC version 20
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:a0000000)
[ 0.000000] Detected 1596.085 MHz processor.
[ 17.971836] Built 1 zonelists. Total pages: 229376
[ 17.971839] Kernel command line: root=/dev/sda1 ro
[ 17.972048] mapped APIC to ffffd000 (fee00000)
[ 17.972051] mapped IOAPIC to ffffc000 (fec00000)
[ 17.972054] Enabling fast FPU save and restore... done.
[ 17.972057] Enabling unmasked SIMD FPU exception support... done.
[ 17.972061] Initializing CPU#0
[ 17.972126] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 17.973647] Console: colour VGA+ 80x25
[ 17.976113] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 17.976569] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 17.994368] Memory: 902104k/917504k available (1408k kernel code, 14816k reserved, 559k data, 196k init, 0k highmem)
[ 17.994449] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 18.054045] Calibrating delay using timer specific routine.. 3194.44 BogoMIPS (lpj=1597223)
[ 18.054199] Mount-cache hash table entries: 512
[ 18.054351] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[ 18.054361] CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[ 18.054368] monitor/mwait feature present.
[ 18.054422] using mwait in idle threads.
[ 18.054476] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 18.054564] CPU: L2 cache: 2048K
[ 18.054616] CPU: Physical Processor ID: 0
[ 18.054668] CPU: Processor Core ID: 0
[ 18.054720] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
[ 18.054729] Compat vDSO mapped to ffffe000.
[ 18.054792] Checking 'hlt' instruction... OK.
[ 18.058140] SMP alternatives: switching to UP code
[ 18.058293] ACPI: Core revision 20060707
[ 18.091651] CPU0: Intel Genuine Intel(R) CPU T2050 @ 1.60GHz stepping 08
[ 18.091832] SMP alternatives: switching to SMP code
[ 18.092007] Booting processor 1/1 eip 3000
[ 18.102538] Initializing CPU#1
[ 18.162923] Calibrating delay using timer specific routine.. 3191.58 BogoMIPS (lpj=1595793)
[ 18.162930] CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[ 18.162938] CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
[ 18.162943] monitor/mwait feature present.
[ 18.162946] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 18.162949] CPU: L2 cache: 2048K
[ 18.162951] CPU: Physical Processor ID: 0
[ 18.162953] CPU: Processor Core ID: 1
[ 18.162955] CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
[ 18.163353] CPU1: Intel Genuine Intel(R) CPU T2050 @ 1.60GHz stepping 08
[ 18.163934] Total of 2 processors activated (6386.03 BogoMIPS).
[ 18.164188] ENABLING IO-APIC IRQs
[ 18.164426] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 18.275811] checking TSC synchronization across 2 CPUs: passed.
[ 0.000955] Brought up 2 CPUs
[ 0.284715] migration_cost=53
[ 0.284964] checking if image is initramfs... it is
[ 0.678499] Freeing initrd memory: 3914k freed
[ 0.678916] NET: Registered protocol family 16
[ 0.679050] ACPI: bus type pci registered
[ 0.679108] PCI: Using MMCONFIG
[ 0.680097] Setting up standard PCI resources
[ 0.699770] ACPI: Interpreter enabled
[ 0.699825] ACPI: Using IOAPIC for interrupt routing
[ 0.712680] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.712738] PCI: Probing PCI hardware (bus 00)
[ 0.719670] Boot video device is 0000:00:02.0
[ 0.720318] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[ 0.721506] PCI: Transparent bridge - 0000:00:1e.0
[ 0.721623] PCI: Bus #09 (-#0c) is hidden behind transparent bridge #08 (-#09) (try 'pci=assign-busses')
[ 0.721701] Please report the result to linux-kernel to fix this permanently
[ 0.721815] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.729700] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.729986] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.730273] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.731404] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.732533] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15)
[ 0.733247] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 *3 4 5 6 7 11 12 14 15)
[ 0.733932] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.734674] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.735432] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.736212] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.736976] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 *4 5 6 7 10 12 14 15)
[ 0.737672] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 11 12 14 15)
[ 0.738177] ACPI: Embedded Controller [EC] (gpe 23) interrupt mode.
[ 0.743243] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.743312] pnp: PnP ACPI init
[ 0.753240] pnp: PnP ACPI: found 9 devices
[ 0.753343] PCI: Using ACPI for IRQ routing
[ 0.753397] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.753969] PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
[ 0.754032] PCI: Bridge: 0000:00:1c.0
[ 0.754087] IO window: 2000-2fff
[ 0.754151] MEM window: d6000000-d7ffffff
[ 0.754207] PREFETCH window: d0000000-d1ffffff
[ 0.754266] PCI: Bridge: 0000:00:1c.1
[ 0.754321] IO window: 3000-3fff
[ 0.754376] MEM window: d8000000-d9ffffff
[ 0.754433] PREFETCH window: d2000000-d3ffffff
[ 0.754491] PCI: Bridge: 0000:00:1c.2
[ 0.754545] IO window: 4000-4fff
[ 0.754602] MEM window: da000000-dbffffff
[ 0.754658] PREFETCH window: d4000000-d5ffffff
[ 0.754725] PCI: Bus 9, cardbus bridge: 0000:08:03.0
[ 0.754781] IO window: 00005000-000050ff
[ 0.754839] IO window: 00005400-000054ff
[ 0.754896] PREFETCH window: 50000000-51ffffff
[ 0.754954] MEM window: 52000000-53ffffff
[ 0.755011] PCI: Bridge: 0000:00:1e.0
[ 0.755065] IO window: 5000-5fff
[ 0.755131] MEM window: dc000000-dc0fffff
[ 0.755187] PREFETCH window: 50000000-51ffffff
[ 0.755264] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
[ 0.755374] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.755396] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 177
[ 0.755504] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.755524] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185
[ 0.755632] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.755642] PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
[ 0.755703] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.755718] PCI: Enabling device 0000:08:03.0 (0000 -> 0003)
[ 0.755777] ACPI: PCI Interrupt 0000:08:03.0[A] -> GSI 16 (level, low) -> IRQ 177
[ 0.755888] PCI: Setting latency timer of device 0000:08:03.0 to 64
[ 0.755915] NET: Registered protocol family 2
[ 0.769144] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.769338] TCP established hash table entries: 131072 (order: 8, 1572864 bytes)
[ 0.770560] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.771234] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.771295] TCP reno registered
[ 0.771542] Simple Boot Flag at 0x36 set to 0x1
[ 0.772608] Initializing Cryptographic API
[ 0.772670] io scheduler noop registered
[ 0.772759] io scheduler anticipatory registered (default)
[ 0.772885] io scheduler deadline registered
[ 0.772985] io scheduler cfq registered
[ 0.773309] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.773359] assign_interrupt_mode Found MSI capability
[ 0.773473] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.773515] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.773550] Allocate Port Service[0000:00:1c.0:pcie03]
[ 0.773594] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.773643] assign_interrupt_mode Found MSI capability
[ 0.773742] Allocate Port Service[0000:00:1c.1:pcie00]
[ 0.773783] Allocate Port Service[0000:00:1c.1:pcie02]
[ 0.773817] Allocate Port Service[0000:00:1c.1:pcie03]
[ 0.773863] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.773912] assign_interrupt_mode Found MSI capability
[ 0.774011] Allocate Port Service[0000:00:1c.2:pcie00]
[ 0.774048] Allocate Port Service[0000:00:1c.2:pcie02]
[ 0.774085] Allocate Port Service[0000:00:1c.2:pcie03]
[ 0.797628] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 0.798806] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 0.798983] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 0.799042] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 0.799372] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 0.802193] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 0.805641] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.806389] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.807395] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.809028] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.809985] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.810103] mice: PS/2 mouse device common for all mice
[ 0.810253] TCP bic registered
[ 0.810943] NET: Registered protocol family 1
[ 0.811008] Using IPI No-Shortcut mode
[ 0.811377] Time: tsc clocksource has been installed.
[ 0.811473] ACPI: (supports S0 S3 S4 S5)
[ 0.811856] Freeing unused kernel memory: 196k freed
[ 0.862634] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 0.863294] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 0.864590] ACPI: CPU0 (power states: C1[C1] C2[C2])
[ 0.864744] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 0.865429] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 0.865786] ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ SONY] OemTableId [ J4] [20060707]
[ 0.866254] ACPI: CPU1 (power states: C1[C1] C2[C2])
[ 0.866408] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 0.868132] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[ 0.869086] ACPI: Thermal Zone [TZ00] (36 C)
[ 0.870127] ACPI Exception (acpi_thermal-0412): AE_NOT_FOUND, Invalid active threshold [0] [20060707]
[ 0.871051] ACPI: Thermal Zone [TZ01] (36 C)
[ 1.051000] Time: acpi_pm clocksource has been installed.
[ 1.409000] ICH7: IDE controller at PCI slot 0000:00:1f.1
[ 1.409000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 185
[ 1.409000] ICH7: chipset revision 2
[ 1.409000] ICH7: not 100% native mode: will probe irqs later
[ 1.409000] ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio
[ 1.410000] Probing IDE interface ide0...
[ 1.600000] input: AT Translated Set 2 keyboard as /class/input/input0
[ 2.082000] hda: PIONEER DVD-RW DVR-K16D, ATAPI CD/DVD-ROM drive
[ 2.695000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 2.703000] hda: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2000kB Cache, UDMA(33)
[ 2.704000] Uniform CD-ROM driver Revision: 3.20
[ 2.785000] SCSI subsystem initialized
[ 2.789000] libata version 2.00 loaded.
[ 2.791000] ata_piix 0000:00:1f.2: version 2.00
[ 2.791000] ata_piix 0000:00:1f.2: MAP [ P0 P2 XX XX ]
[ 2.791000] ata_piix 0000:00:1f.2: invalid MAP value 0
[ 2.942000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 225
[ 2.942000] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 2.942000] ata1: SATA max UDMA/133 cmd 0x18B0 ctl 0x18A6 bmdma 0x1890 irq 225
[ 2.942000] ata2: SATA max UDMA/133 cmd 0x18A8 ctl 0x18A2 bmdma 0x1898 irq 225
[ 2.942000] scsi0 : ata_piix
[ 3.094000] ata1.00: ATA-7, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 0/32)
[ 3.094000] ata1.00: ata1: dev 0 multi count 16
[ 3.097000] ata1.00: configured for UDMA/100
[ 3.097000] scsi1 : ata_piix
[ 10.144000] ata2: port is slow to respond, please be patient
[ 33.104000] ata2: port failed to respond (30 secs)
[ 33.255000] ata2: SRST failed (status 0xFF)
[ 33.255000] ata2: SRST failed (err_mask=0x100)
[ 33.255000] ata2: softreset failed, retrying in 5 secs
[ 38.407000] ata2: SRST failed (status 0xFF)
[ 38.407000] ata2: SRST failed (err_mask=0x100)
[ 38.407000] ata2: softreset failed, retrying in 5 secs
[ 43.560000] ata2: SRST failed (status 0xFF)
[ 43.560000] ata2: SRST failed (err_mask=0x100)
[ 43.560000] ata2: reset failed, giving up
[ 43.560000] Vendor: ATA Model: FUJITSU MHV2120B Rev: 0000
[ 43.561000] Type: Direct-Access ANSI SCSI revision: 05
[ 43.567000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 43.567000] sda: Write Protect is off
[ 43.567000] sda: Mode Sense: 00 3a 00 00
[ 43.567000] SCSI device sda: drive cache: write back
[ 43.568000] SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
[ 43.568000] sda: Write Protect is off
[ 43.568000] sda: Mode Sense: 00 3a 00 00
[ 43.568000] SCSI device sda: drive cache: write back
[ 43.568000] sda: sda1 sda2 sda3
[ 43.924000] sd 0:0:0:0: Attached scsi disk sda
[ 44.182000] usbcore: registered new driver usbfs
[ 44.182000] usbcore: registered new driver hub
[ 44.188000] USB Universal Host Controller Interface driver v3.0
[ 44.188000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 233
[ 44.188000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 44.188000] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 44.188000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 44.188000] uhci_hcd 0000:00:1d.0: irq 233, io base 0x00001820
[ 44.189000] usb usb1: configuration #1 chosen from 1 choice
[ 44.189000] hub 1-0:1.0: USB hub found
[ 44.189000] hub 1-0:1.0: 2 ports detected
[ 44.200000] ieee1394: Initialized config rom entry `ip1394'
[ 44.290000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 169
[ 44.291000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 44.291000] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 44.291000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 44.291000] uhci_hcd 0000:00:1d.1: irq 169, io base 0x00001840
[ 44.291000] usb usb2: configuration #1 chosen from 1 choice
[ 44.291000] hub 2-0:1.0: USB hub found
[ 44.291000] hub 2-0:1.0: 2 ports detected
[ 44.392000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 233
[ 44.393000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 44.393000] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 44.393000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
[ 44.393000] ehci_hcd 0000:00:1d.7: debug port 1
[ 44.393000] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 44.393000] ehci_hcd 0000:00:1d.7: irq 233, io mem 0xdc444000
[ 44.397000] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 44.397000] usb usb3: configuration #1 chosen from 1 choice
[ 44.397000] hub 3-0:1.0: USB hub found
[ 44.397000] hub 3-0:1.0: 6 ports detected
[ 44.499000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
[ 44.499000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 44.499000] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 44.499000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 44.499000] uhci_hcd 0000:00:1d.2: irq 185, io base 0x00001860
[ 44.499000] usb usb4: configuration #1 chosen from 1 choice
[ 44.499000] hub 4-0:1.0: USB hub found
[ 44.499000] hub 4-0:1.0: 2 ports detected
[ 44.601000] PCI: Enabling device 0000:08:03.1 (0000 -> 0002)
[ 44.601000] ACPI: PCI Interrupt 0000:08:03.1[A] -> GSI 16 (level, low) -> IRQ 177
[ 44.601000] PCI: Setting latency timer of device 0000:08:03.1 to 64
[ 44.658000] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[177] MMIO=[dc005000-dc0057ff] Max Packet=[2048] IR/IT contexts=[4/8]
[ 44.670000] Probing IDE interface ide1...
[ 45.211000] Attempting manual resume
[ 45.223000] EXT3-fs: INFO: recovery required on readonly filesystem.
[ 45.223000] EXT3-fs: write access will be enabled during recovery.
[ 45.250000] kjournald starting. Commit interval 5 seconds
[ 45.250000] EXT3-fs: recovery complete.
[ 45.251000] EXT3-fs: mounted filesystem with ordered data mode.
[ 45.916000] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0800460302320543]
[ 50.698000] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 51.622000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 51.705000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 51.724000] Linux agpgart interface v0.101 (c) Dave Jones
[ 51.734000] agpgart: Detected an Intel 945GM Chipset.
[ 51.735000] agpgart: Detected 7932K stolen memory.
[ 51.753000] agpgart: AGP aperture is 256M @ 0xc0000000
[ 51.824000] input: PC Speaker as /class/input/input1
[ 51.931000] Real Time Clock Driver v1.12ac
[ 52.325000] input: PS/2 Mouse as /class/input/input2
[ 52.345000] input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
[ 52.387000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 177
[ 52.387000] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 52.387000] sky2 v1.5 addr 0xd6000000 irq 177 Yukon-FE (0xb7) rev 1
[ 52.388000] sky2 eth0: addr 00:13:a9:7d:aa:6f
[ 52.442000] ts: Compaq touchscreen protocol output
[ 52.649000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 58
[ 52.649000] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 52.699000] sky2 eth0: enabling interface
[ 52.741000] hda_codec: Unknown model for ALC262, trying auto-probe from BIOS...
[ 52.967000] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
[ 52.967000] ieee1394: sbp2: Try serialize_io=0 for better performance
[ 53.023000] Adding 2104504k swap on /dev/sda2. Priority:-1 extents:1 across:2104504k
[ 53.067000] EXT3 FS on sda1, internal journal
[ 53.677000] kjournald starting. Commit interval 5 seconds
[ 53.678000] EXT3 FS on sda3, internal journal
[ 53.679000] EXT3-fs: mounted filesystem with ordered data mode.
[ 53.809000] NET: Registered protocol family 17
[ 54.587000] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control none
[ 57.064000] NET: Registered protocol family 10
[ 57.064000] lo: Disabled Privacy Extensions
[ 57.064000] IPv6 over IPv4 tunneling driver
[ 58.956000] ACPI: AC Adapter [ADP1] (on-line)
[ 59.006000] ACPI: Battery Slot [BAT0] (battery present)
[ 59.021000] ACPI: Lid Switch [LID0]
[ 59.022000] ACPI: Power Button (CM) [PWRB]
[ 59.067000] Using specific hotkey driver
[ 59.138000] ibm_acpi: ec object not found
[ 59.176000] toshiba_acpi: Unknown parameter `hotkeys_over_acpi'
[ 59.186000] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 62.645000] [drm] Initialized drm 1.0.1 20051102
[ 62.660000] ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 177
[ 62.662000] [drm] Initialized i915 1.5.0 20060119 on minor 0
[ 63.033000] sonypi: Sony Programmable I/O Controller Driver v1.26.
[ 63.036000] sonypi: detected type3 model, verbose = 0, fnkeyinit = off, camera = off, compat = off, mask = 0xffffffff, useinput = on, acpi = on
[ 63.036000] sonypi: enabled at irq=11, port1=0x1080, port2=0x1084
[ 63.036000] sonypi: device allocated minor is 63
[ 63.037000] input: Sony Vaio Jogdial as /class/input/input4
[ 63.047000] input: Sony Vaio Keys as /class/input/input5
[ 63.176000] sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646)
[ 63.218000] sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 657)
[ 63.260000] sonypi command failed at drivers/char/sonypi.c : sonypi_call2 (line 659)
[ 63.307000] sonypi command failed at drivers/char/sonypi.c : sonypi_call1 (line 646)
[ 67.132000] psmouse.c: GlidePoint at isa0060/serio4/input0 lost synchronization, throwing 1 bytes away.
[ 67.256000] eth0: no IPv6 routers present
[ 67.640000] psmouse.c: resync failed, issuing reconnect request
next reply other threads:[~2006-10-25 18:47 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-10-25 18:45 Stephen Hemminger [this message]
2006-10-25 19:06 ` Slow SATA detection on bootup Jeff Garzik
2006-10-25 21:07 ` Stephen Hemminger
2006-12-16 17:02 ` Jeff Garzik
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20061025114504.450b3425@localhost \
--to=shemminger@osdl.org \
--cc=jgarzik@pobox.com \
--cc=linux-ide@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.