From: jurriaan <thunder7@xs4all.nl>
To: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org, alan@lxorguk.ukuu.org.uk
Subject: scary message 'failed to recover some devices ... retrying' HPT370
Date: Tue, 31 Oct 2006 19:59:21 +0100 [thread overview]
Message-ID: <20061031185921.GA3636@amd64.of.nowhere> (raw)
On a whim, after reading about recent developments, I tried to boot
2.6.19-rc4-mm1 with only the new SATA drivers active, and all PATA
drivers inactive.
This is an Asus A8N-SLI Premium motherboard, with 8 sata drives on the
NForce chipset and on a SiL3114 controller, 3 pata devices (2 hd, 1 dvd
writer) on the motherboards PATA connectors and, for good measure, 2
additional hds on a HPT374 4-port PATA raid card, in JBOD mode.
The message reads 'ata11: failed to recover some devices, retrying in 5
secs' in this part:
pata_hpt37x: BIOS has not set timing clocks.
hpt37x: HPT374: Bus clock 33MHz.
ACPI: PCI Interrupt 0000:05:06.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
ata11: PATA max UDMA/133 cmd 0x6000 ctl 0x6402 bmdma 0x7000 irq 16
ata12: PATA max UDMA/133 cmd 0x6800 ctl 0x6C02 bmdma 0x7008 irq 16
scsi10 : pata_hpt37x
ata11.00: ATA-6, max UDMA/100, 488397168 sectors: LBA48
ata11.00: ata11: dev 0 multi count 16
ata11.01: failed to IDENTIFY (I/O error, err_mask=0x1)
ata11: failed to recover some devices, retrying in 5 secs
ata11.01: failed to IDENTIFY (I/O error, err_mask=0x1)
ata11: failed to recover some devices, retrying in 5 secs
ata11.01: failed to IDENTIFY (I/O error, err_mask=0x1)
ata11: failed to recover some devices, retrying in 5 secs
Find mode for 12 reports A81F442
Find mode for DMA 69 reports 12848242
ata11.00: configured for UDMA/100
scsi11 : pata_hpt37x
ATA: abnormal status 0x8 on port 0x6807
scsi 10:0:0:0: Direct-Access ATA WDC WD2500JB-00F 15.0 PQ: 0 ANSI: 5
SCSI device sdk: 488397168 512-byte hdwr sectors (250059 MB)
sdk: Write Protect is off
sdk: Mode Sense: 00 3a 00 00
SCSI device sdk: drive cache: write back
SCSI device sdk: 488397168 512-byte hdwr sectors (250059 MB)
sdk: Write Protect is off
sdk: Mode Sense: 00 3a 00 00
SCSI device sdk: drive cache: write back
sdk: sdk1
sd 10:0:0:0: Attached scsi disk sdk
sd 10:0:0:0: Attached scsi generic sg11 type 0
pata_hpt37x: BIOS has not set timing clocks.
hpt37x: HPT374: Bus clock 33MHz.
ACPI: PCI Interrupt 0000:05:06.1[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
ata13: PATA max UDMA/133 cmd 0x7400 ctl 0x7802 bmdma 0x8400 irq 16
ata14: PATA max UDMA/133 cmd 0x7C00 ctl 0x8002 bmdma 0x8408 irq 16
scsi12 : pata_hpt37x
ata13.00: ATA-7, max UDMA/100, 586072368 sectors: LBA48
ata13.00: ata13: dev 0 multi count 16
Find mode for 12 reports A81F442
Find mode for DMA 69 reports 12848242
ata13.00: configured for UDMA/100
scsi13 : pata_hpt37x
ATA: abnormal status 0x8 on port 0x7C07
scsi 12:0:0:0: Direct-Access ATA ST3300831A 3.01 PQ: 0 ANSI: 5
SCSI device sdl: 586072368 512-byte hdwr sectors (300069 MB)
sdl: Write Protect is off
sdl: Mode Sense: 00 3a 00 00
SCSI device sdl: drive cache: write back
SCSI device sdl: 586072368 512-byte hdwr sectors (300069 MB)
sdl: Write Protect is off
sdl: Mode Sense: 00 3a 00 00
SCSI device sdl: drive cache: write back
sdl: sdl1
It seems that one of the empty ports on the HPT374 card is giving these
scary messages. Why only one of the empty ports? lspci -v and dmesg
(both for 2.6.19-rc4-mm1 with regular PATA drivers and without) included
below.
Are these messages anything to worry about?
Kind regards,
Jurriaan
[please note: I'm subscribed to lkml, not to linux-ide]
lspci -v:
00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
Subsystem: ASUSTeK Computer Inc. Unknown device 815a
Flags: bus master, 66MHz, fast devsel, latency 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Capabilities: [e0] HyperTransport: MSI Mapping
00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0
00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: 66MHz, fast devsel, IRQ 7
I/O ports at e400 [size=32]
I/O ports at 4c00 [size=64]
I/O ports at 4c40 [size=64]
Capabilities: [44] Power Management version 2
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev a2) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23
Memory at da004000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev a3) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 20
Memory at feb00000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97 Audio Controller (rev a2)
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 7
I/O ports at dc00 [size=256]
I/O ports at e000 [size=256]
Memory at da003000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 815a
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 22
I/O ports at 09f0 [size=8]
I/O ports at 0bf0 [size=4]
I/O ports at 0970 [size=8]
I/O ports at 0b70 [size=4]
I/O ports at d800 [size=16]
Memory at da002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller (rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 21
I/O ports at 09e0 [size=8]
I/O ports at 0be0 [size=4]
I/O ports at 0960 [size=8]
I/O ports at 0b60 [size=4]
I/O ports at c400 [size=16]
Memory at da001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode])
Flags: bus master, 66MHz, fast devsel, latency 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=128
I/O behind bridge: 00006000-0000afff
Memory behind bridge: d8000000-d9ffffff
Prefetchable memory behind bridge: da100000-da1fffff
00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 23
Memory at da000000 (32-bit, non-prefetchable) [size=4K]
I/O ports at b000 [size=8]
Capabilities: [44] Power Management version 2
00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel
00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel
00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel
00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: d0000000-d7ffffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Capabilities: [40] Power Management version 2
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable-
Capabilities: [58] HyperTransport: MSI Mapping
Capabilities: [80] Express Root Port (Slot+) IRQ 0
Capabilities: [100] Virtual Channel
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration
Flags: fast devsel
Capabilities: [80] HyperTransport: Host or Secondary Interface
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map
Flags: fast devsel
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller
Flags: fast devsel
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control
Flags: fast devsel
01:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600] (rev a2) (prog-if 00 [VGA])
Flags: bus master, fast devsel, latency 0, IRQ 18
Memory at d0000000 (32-bit, non-prefetchable) [size=64M]
Memory at c0000000 (64-bit, prefetchable) [size=256M]
Memory at d4000000 (64-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at d5000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Capabilities: [78] Express Endpoint IRQ 0
Capabilities: [100] Virtual Channel
Capabilities: [128] Power Budgeting
05:06.0 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07)
Subsystem: Triones Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 16
I/O ports at 6000 [size=8]
I/O ports at 6400 [size=4]
I/O ports at 6800 [size=8]
I/O ports at 6c00 [size=4]
I/O ports at 7000 [size=256]
Expansion ROM at da1c0000 [disabled by cmd] [size=128K]
Capabilities: [60] Power Management version 2
05:06.1 RAID bus controller: Triones Technologies, Inc. HPT374 (rev 07)
Subsystem: Triones Technologies, Inc. Unknown device 0001
Flags: bus master, 66MHz, medium devsel, latency 120, IRQ 16
I/O ports at 7400 [size=8]
I/O ports at 7800 [size=4]
I/O ports at 7c00 [size=8]
I/O ports at 8000 [size=4]
I/O ports at 8400 [size=256]
Capabilities: [60] Power Management version 2
05:07.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 20)
Subsystem: Lite-On Communications Inc LNE100TX
Flags: bus master, medium devsel, latency 32, IRQ 17
I/O ports at 8800 [size=256]
Memory at d900f000 (32-bit, non-prefetchable) [size=256]
[virtual] Expansion ROM at da180000 [disabled] [size=256K]
05:08.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04)
Subsystem: Creative Labs Unknown device 2001
Flags: bus master, medium devsel, latency 32, IRQ 18
I/O ports at 8c00 [size=64]
Capabilities: [dc] Power Management version 2
05:08.1 Input device controller: Creative Labs SB Audigy Game Port (rev 04)
Subsystem: Creative Labs SB Audigy MIDI/Game Port
Flags: bus master, medium devsel, latency 32
I/O ports at 9000 [size=8]
Capabilities: [dc] Power Management version 2
05:08.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (rev 04) (prog-if 10 [OHCI])
Subsystem: Creative Labs SB Audigy FireWire Port
Flags: bus master, medium devsel, latency 32, IRQ 19
Memory at d900e000 (32-bit, non-prefetchable) [size=2K]
Memory at d9000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
05:0a.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
Subsystem: ASUSTeK Computer Inc. Unknown device 8167
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 19
I/O ports at 9400 [size=8]
I/O ports at 9800 [size=4]
I/O ports at 9c00 [size=8]
I/O ports at a000 [size=4]
I/O ports at a400 [size=16]
Memory at d900c000 (32-bit, non-prefetchable) [size=1K]
[virtual] Expansion ROM at da100000 [disabled] [size=512K]
Capabilities: [60] Power Management version 2
05:0b.0 FireWire (IEEE 1394): Texas Instruments TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. K8N4-E Mainboard
Flags: bus master, medium devsel, latency 32, IRQ 16
Memory at d900d000 (32-bit, non-prefetchable) [size=2K]
Memory at d9004000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
05:0c.0 Ethernet controller: Marvell Technology Group Ltd. 88E8001 Gigabit Ethernet Controller (rev 13)
Subsystem: ASUSTeK Computer Inc. Marvell 88E8001 Gigabit Ethernet Controller (Asus)
Flags: bus master, 66MHz, medium devsel, latency 32, IRQ 17
Memory at d9008000 (32-bit, non-prefetchable) [size=16K]
I/O ports at a800 [size=256]
[virtual] Expansion ROM at da1e0000 [disabled] [size=128K]
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
dmesg for 2.6.19-rc4-mm1 with PATA drivers:
Linux version 2.6.19-rc4-mm1 (jurriaan@middle) (gcc version 4.1.2 20061028 (prerelease) (Debian 4.1.1-19)) #8 SMP Tue Oct 31 19:10:57 CET 2006
Command line: root=/dev/md2 video=nvidiafb:1600x1200-32@85 atkbd.softrepeat=1
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c800 (usable)
BIOS-e820: 000000000009c800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
BIOS-e820: 00000000bfff0000 - 00000000bfff3000 (ACPI NVS)
BIOS-e820: 00000000bfff3000 - 00000000c0000000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
Entering add_active_range(0, 0, 156) 0 entries of 256 used
Entering add_active_range(0, 256, 786416) 1 entries of 256 used
Entering add_active_range(0, 1048576, 1310720) 2 entries of 256 used
end_pfn_map = 1310720
DMI 2.3 present.
ACPI: RSDP (v000 Nvidia ) @ 0x00000000000f7d30
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff30c0
ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x00000000bfff9900
ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x00000000bfff9b80
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff9cc0
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff9840
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
Entering add_active_range(0, 0, 156) 0 entries of 256 used
Entering add_active_range(0, 256, 786416) 1 entries of 256 used
Entering add_active_range(0, 1048576, 1310720) 2 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1310720
early_node_map[3] active PFN ranges
0: 0 -> 156
0: 256 -> 786416
0: 1048576 -> 1310720
On node 0 totalpages: 1048460
DMA zone: 56 pages used for memmap
DMA zone: 1852 pages reserved
DMA zone: 2088 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 768040 pages, LIFO batch:31
Normal zone: 3584 pages used for memmap
Normal zone: 258560 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009c000 - 000000000009d000
Nosave address range: 000000000009d000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000f0000
Nosave address range: 00000000000f0000 - 0000000000100000
Nosave address range: 00000000bfff0000 - 00000000bfff3000
Nosave address range: 00000000bfff3000 - 00000000c0000000
Nosave address range: 00000000c0000000 - 00000000e0000000
Nosave address range: 00000000e0000000 - 00000000f0000000
Nosave address range: 00000000f0000000 - 00000000fec00000
Nosave address range: 00000000fec00000 - 0000000100000000
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
PERCPU: Allocating 31936 bytes of per cpu data
Built 1 zonelists. Total pages: 1028688
Kernel command line: root=/dev/md2 video=nvidiafb:1600x1200-32@85 atkbd.softrepeat=1
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
CPU 0: aperture @ 8000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 8000000
Memory: 4042632k/5242880k available (3945k kernel code, 150996k reserved, 2407k data, 288k init)
Calibrating delay using timer specific routine.. 5042.57 BogoMIPS (lpj=2521288)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Freeing SMP alternatives: 44k freed
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 13128039
Detected 13.128 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5040.43 BogoMIPS (lpj=2520217)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 01
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff -76 cycles, maxerr 588 cycles)
Brought up 2 CPUs
testing NMI watchdog ... CPU#0: NMI appears to be stuck (111->116)!
CPU#1: NMI appears to be stuck (60->65)!
Uhhuh. NMI received for unknown reason 3d.
Do you have a strange power saving mode enabled?
Dazed and confused, but trying to continue
Disabling vsyscall due to use of PM timer
time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
time.c: Detected 2520.581 MHz processor.
Uhhuh. NMI received for unknown reason 00.
Do you have a strange power saving mode enabled?
Dazed and confused, but trying to continue
migration_cost=141
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000
PCI: No mmconfig possible on device 00:18
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:09.0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 8000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:05:08.2[B] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[d900e000-d900e7ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:05:0b.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[d900d000-d900d7ff] Max Packet=[2048] IR/IT contexts=[4/8]
PCI: Bridge: 0000:00:09.0
IO window: 6000-afff
MEM window: d8000000-d9ffffff
PREFETCH window: da100000-da1fffff
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: d0000000-d7ffffff
PREFETCH window: c0000000-cfffffff
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
Coda Kernel/Venus communications, v6.0.0, coda@cs.cmu.edu
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.27 [Flags: R/O].
io scheduler noop registered
io scheduler cfq registered (default)
PCI: Linking AER extended capability on 0000:00:0b.0
PCI: Linking AER extended capability on 0000:00:0c.0
PCI: Linking AER extended capability on 0000:00:0d.0
PCI: Linking AER extended capability on 0000:00:0e.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
Allocate Port Service[0000:00:0d.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
nvidiafb: Device ID: 10de0141
nvidiafb: CRTC0 analog found
nvidiafb: CRTC1 analog found
nvidiafb: EDID found from BUS2
nvidiafb: CRTC 0 appears to have a CRT attached
nvidiafb: Using CRT on CRTC 0
nvidiafb: MTRR set to ON
Console: switching to colour frame buffer device 160x66
nvidiafb: PCI nVidia NV14 framebuffer (64MB @ 0xC0000000)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Using specific hotkey driver
lp: driver loaded but no devices found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using monotonic_clock().
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:05:0c.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
skge 1.9 addr 0xd9008000 irq 17 chip Yukon-Lite rev 9
skge eth0: addr 00:15:f2:20:e6:69
Marvell 88E1101: Registered new driver
Davicom DM9161E: Registered new driver
Davicom DM9131: Registered new driver
Cicada Cis8204: Registered new driver
Cicada Cis8201: Registered new driver
LXT970: Registered new driver
LXT971: Registered new driver
QS6612: Registered new driver
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
eth1: forcedeth.c: subsystem: 01043:8141 bound to 0000:00:0a.0
Linux Tulip driver version 1.1.14 (May 11, 2002)
ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
tulip0: MII transceiver #1 config 3100 status 7829 advertising 01e1.
eth2: Lite-On 82c168 PNIC rev 32 at Port 0x8800, 00:A0:CC:21:89:0C, IRQ 17.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
NFORCE-CK804: chipset revision 242
NFORCE-CK804: not 100% native mode: will probe irqs later
NFORCE-CK804: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD2000JB-32EVA0, ATA DISK drive
ieee1394: The root node is not cycle master capable; selecting a new root node and resetting...
hdb: _NEC DVD_RW ND-3540A, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
ieee1394: Host added: ID:BUS[1-00:1023] GUID[0011d80000738f5d]
hdc: WDC WD2000JB-00FUA0, ATA DISK drive
ieee1394: Host added: ID:BUS[0-01:1023] GUID[00023c014100f4bf]
ide1 at 0x170-0x177,0x376 on irq 15
HPT374: IDE controller at PCI slot 0000:05:06.0
ACPI: PCI Interrupt 0000:05:06.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
HPT374: chipset revision 7
HPT374: DPLL base: 48 MHz, f_CNT: 147, assuming 33 MHz PCI
HPT374: using 66 MHz DPLL clock
HPT374: 100% native mode on irq 16
ide2: BM-DMA at 0x7000-0x7007, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0x7008-0x700f, BIOS settings: hdg:pio, hdh:pio
ACPI: PCI Interrupt 0000:05:06.1[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
HPT374: no clock data saved by BIOS
HPT374: DPLL base: 48 MHz, f_CNT: 122, assuming 33 MHz PCI
HPT374: using 66 MHz DPLL clock
ide4: BM-DMA at 0x8400-0x8407, BIOS settings: hdi:DMA, hdj:pio
ide5: BM-DMA at 0x8408-0x840f, BIOS settings: hdk:pio, hdl:pio
Probing IDE interface ide2...
hde: WDC WD2500JB-00FUA0, ATA DISK drive
ide2 at 0x6000-0x6007,0x6402 on irq 16
Probing IDE interface ide3...
Probing IDE interface ide4...
hdi: ST3300831A, ATA DISK drive
ide4 at 0x7400-0x7407,0x7802 on irq 16
Probing IDE interface ide5...
Probing IDE interface ide3...
Probing IDE interface ide5...
hda: max request size: 512KiB
hda: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 >
hdc: max request size: 512KiB
hdc: 390721968 sectors (200049 MB) w/8192KiB Cache, CHS=24321/255/63, UDMA(100)
hdc: cache flushes supported
hdc: hdc1 hdc2 < hdc5 hdc6 hdc7 hdc8 hdc9 >
hde: max request size: 512KiB
hde: 488397168 sectors (250059 MB) w/8192KiB Cache, CHS=30401/255/63, UDMA(100)
hde: cache flushes supported
hde: hde1
hdi: max request size: 512KiB
hdi: 586072368 sectors (300069 MB) w/8192KiB Cache, CHS=36481/255/63, UDMA(100)
hdi: cache flushes supported
hdi: hdi1
hdb: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
RocketRAID 3xxx SATA Controller driver v1.0 (060426)
libata version 2.00 loaded.
sata_sil 0000:05:0a.0: version 2.0
ACPI: PCI Interrupt 0000:05:0a.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
sata_sil 0000:05:0a.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xFFFFC200100BA080 ctl 0xFFFFC200100BA08A bmdma 0xFFFFC200100BA000 irq 19
ata2: SATA max UDMA/100 cmd 0xFFFFC200100BA0C0 ctl 0xFFFFC200100BA0CA bmdma 0xFFFFC200100BA008 irq 19
ata3: SATA max UDMA/100 cmd 0xFFFFC200100BA280 ctl 0xFFFFC200100BA28A bmdma 0xFFFFC200100BA200 irq 19
ata4: SATA max UDMA/100 cmd 0xFFFFC200100BA2C0 ctl 0xFFFFC200100BA2CA bmdma 0xFFFFC200100BA208 irq 19
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/100
scsi2 : sata_sil
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata3.00: ata3: dev 0 multi count 16
ata3.00: configured for UDMA/100
scsi3 : sata_sil
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata4.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata4.00: ata4: dev 0 multi count 16
ata4.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1
sd 1:0:0:0: Attached scsi disk sdb
sd 1:0:0:0: Attached scsi generic sg1 type 0
scsi 2:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
sdc: sdc1
sd 2:0:0:0: Attached scsi disk sdc
sd 2:0:0:0: Attached scsi generic sg2 type 0
scsi 3:0:0:0: Direct-Access ATA ST3250823AS 3.02 PQ: 0 ANSI: 5
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
sdd: sdd1
sd 3:0:0:0: Attached scsi disk sdd
sd 3:0:0:0: Attached scsi generic sg3 type 0
sata_nv 0000:00:07.0: version 3.1
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:07.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata5: SATA max UDMA/133 cmd 0xFFFFC200100BC480 ctl 0xFFFFC200100BC4A0 bmdma 0xD800 irq 22
ata6: SATA max UDMA/133 cmd 0xFFFFC200100BC580 ctl 0xFFFFC200100BC5A0 bmdma 0xD808 irq 22
Losing some ticks... checking if CPU frequency changed.
scsi4 : sata_nv
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 31/32)
ata5.00: ata5: dev 0 multi count 1
ata5.00: configured for UDMA/133
scsi5 : sata_nv
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32)
ata6.00: ata6: dev 0 multi count 1
ata6.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA ST3300622AS 3.AA PQ: 0 ANSI: 5
ata5: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sde: 586072368 512-byte hdwr sectors (300069 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: drive cache: write back
SCSI device sde: 586072368 512-byte hdwr sectors (300069 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: drive cache: write back
sde: sde1 sde2
sd 4:0:0:0: Attached scsi disk sde
sd 4:0:0:0: Attached scsi generic sg4 type 0
scsi 5:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
ata6: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sdf: 488397168 512-byte hdwr sectors (250059 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: drive cache: write back
SCSI device sdf: 488397168 512-byte hdwr sectors (250059 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: drive cache: write back
sdf: sdf1
sd 5:0:0:0: Attached scsi disk sdf
sd 5:0:0:0: Attached scsi generic sg5 type 0
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:08.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata7: SATA max UDMA/133 cmd 0xFFFFC200100BE480 ctl 0xFFFFC200100BE4A0 bmdma 0xC400 irq 21
ata8: SATA max UDMA/133 cmd 0xFFFFC200100BE580 ctl 0xFFFFC200100BE5A0 bmdma 0xC408 irq 21
scsi6 : sata_nv
ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata7.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 31/32)
ata7.00: ata7: dev 0 multi count 1
ata7.00: configured for UDMA/133
scsi7 : sata_nv
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata8.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32)
ata8.00: ata8: dev 0 multi count 1
ata8.00: configured for UDMA/133
scsi 6:0:0:0: Direct-Access ATA ST3300622AS 3.AA PQ: 0 ANSI: 5
ata7: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sdg: 586072368 512-byte hdwr sectors (300069 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: drive cache: write back
SCSI device sdg: 586072368 512-byte hdwr sectors (300069 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: drive cache: write back
sdg: sdg1 sdg2
sd 6:0:0:0: Attached scsi disk sdg
sd 6:0:0:0: Attached scsi generic sg6 type 0
scsi 7:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
ata8: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sdh: 488397168 512-byte hdwr sectors (250059 MB)
sdh: Write Protect is off
sdh: Mode Sense: 00 3a 00 00
SCSI device sdh: drive cache: write back
SCSI device sdh: 488397168 512-byte hdwr sectors (250059 MB)
sdh: Write Protect is off
sdh: Mode Sense: 00 3a 00 00
SCSI device sdh: drive cache: write back
sdh: sdh1
sd 7:0:0:0: Attached scsi disk sdh
sd 7:0:0:0: Attached scsi generic sg7 type 0
pata_hpt37x: BIOS has not set timing clocks.
hpt37x: HPT374: Bus clock 33MHz.
PCI: Unable to reserve I/O region #1:8@7400 for device 0000:05:06.1
pata_hpt37x: probe of 0000:05:06.1 failed with error -16
video1394: Installed video1394 module
ieee1394: raw1394: /dev/raw1394 device initialized
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 20, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.19-rc4-mm1 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.1
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 23, io mem 0xda004000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.19-rc4-mm1 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int64x1 2328 MB/s
raid6: int64x2 3148 MB/s
raid6: int64x4 3035 MB/s
raid6: int64x8 2050 MB/s
raid6: sse2x1 2320 MB/s
raid6: sse2x2 3285 MB/s
raid6: sse2x4 3929 MB/s
raid6: using algorithm sse2x4 (3929 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: generic_sse
generic_sse: 8036.000 MB/sec
raid5: using function: generic_sse (8036.000 MB/sec)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
NET: Registered protocol family 8
NET: Registered protocol family 20
powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ processors (version 2.00.00)
powernow-k8: 0 : fid 0x10 (2400 MHz), vid 0x8
powernow-k8: 1 : fid 0xe (2200 MHz), vid 0xa
powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xc
powernow-k8: 3 : fid 0xa (1800 MHz), vid 0xe
powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
logips2pp: Detected unknown logitech mouse model 1
input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdh1 ...
md: adding sdh1 ...
md: adding sdg1 ...
md: adding sdf1 ...
md: adding sde1 ...
md: adding sdd1 ...
md: adding sdc1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: hdc9 has different UUID to sdh1
md: hdc8 has different UUID to sdh1
md: hdc7 has different UUID to sdh1
md: hdc6 has different UUID to sdh1
md: hdc5 has different UUID to sdh1
md: hda9 has different UUID to sdh1
md: hda8 has different UUID to sdh1
md: hda7 has different UUID to sdh1
md: hda6 has different UUID to sdh1
md: hda5 has different UUID to sdh1
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: bind<sdc1>
md: bind<sdd1>
md: bind<sde1>
md: bind<sdf1>
md: bind<sdg1>
md: bind<sdh1>
md: running: <sdh1><sdg1><sdf1><sde1><sdd1><sdc1><sdb1><sda1>
raid5: device sdh1 operational as raid disk 1
raid5: device sdg1 operational as raid disk 0
raid5: device sdf1 operational as raid disk 5
raid5: device sde1 operational as raid disk 6
raid5: device sdd1 operational as raid disk 7
raid5: device sdc1 operational as raid disk 3
raid5: device sdb1 operational as raid disk 2
raid5: device sda1 operational as raid disk 4
raid5: allocated 8462kB for md0
raid5: raid level 6 set md0 active with 8 out of 8 devices, algorithm 2
RAID5 conf printout:
--- rd:8 wd:8
disk 0, o:1, dev:sdg1
disk 1, o:1, dev:sdh1
disk 2, o:1, dev:sdb1
disk 3, o:1, dev:sdc1
disk 4, o:1, dev:sda1
disk 5, o:1, dev:sdf1
disk 6, o:1, dev:sde1
disk 7, o:1, dev:sdd1
md0: bitmap initialized from disk: read 15/15 pages, set 1 bits, status: 0
created bitmap (233 pages) for device md0
md: considering hdc9 ...
md: adding hdc9 ...
md: hdc8 has different UUID to hdc9
md: hdc7 has different UUID to hdc9
md: hdc6 has different UUID to hdc9
md: hdc5 has different UUID to hdc9
md: adding hda9 ...
md: hda8 has different UUID to hdc9
md: hda7 has different UUID to hdc9
md: hda6 has different UUID to hdc9
md: hda5 has different UUID to hdc9
md: created md4
md: bind<hda9>
md: bind<hdc9>
md: running: <hdc9><hda9>
raid1: raid set md4 active with 2 out of 2 mirrors
md4: bitmap initialized from disk: read 10/10 pages, set 48 bits, status: 0
created bitmap (156 pages) for device md4
md: considering hdc8 ...
md: adding hdc8 ...
md: hdc7 has different UUID to hdc8
md: hdc6 has different UUID to hdc8
md: hdc5 has different UUID to hdc8
md: adding hda8 ...
md: hda7 has different UUID to hdc8
md: hda6 has different UUID to hdc8
md: hda5 has different UUID to hdc8
md: created md3
md: bind<hda8>
md: bind<hdc8>
md: running: <hdc8><hda8>
raid1: raid set md3 active with 2 out of 2 mirrors
md3: bitmap initialized from disk: read 8/8 pages, set 5 bits, status: 0
created bitmap (123 pages) for device md3
md: considering hdc7 ...
md: adding hdc7 ...
md: hdc6 has different UUID to hdc7
md: hdc5 has different UUID to hdc7
md: adding hda7 ...
md: hda6 has different UUID to hdc7
md: hda5 has different UUID to hdc7
md: created md2
md: bind<hda7>
md: bind<hdc7>
md: running: <hdc7><hda7>
raid1: raid set md2 active with 2 out of 2 mirrors
md2: bitmap initialized from disk: read 8/8 pages, set 83 bits, status: 0
created bitmap (123 pages) for device md2
md: considering hdc6 ...
md: adding hdc6 ...
md: hdc5 has different UUID to hdc6
md: adding hda6 ...
md: hda5 has different UUID to hdc6
md: created md1
md: bind<hda6>
md: bind<hdc6>
md: running: <hdc6><hda6>
raid1: raid set md1 active with 2 out of 2 mirrors
md1: bitmap initialized from disk: read 12/12 pages, set 70 bits, status: 0
created bitmap (184 pages) for device md1
md: considering hdc5 ...
md: adding hdc5 ...
md: adding hda5 ...
md: created md5
md: bind<hda5>
md: bind<hdc5>
md: running: <hdc5><hda5>
raid1: raid set md5 active with 2 out of 2 mirrors
md5: bitmap initialized from disk: read 9/9 pages, set 0 bits, status: 0
created bitmap (129 pages) for device md5
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 288k freed
Adding 4200888k swap on /dev/md5. Priority:-1 extents:1 across:4200888k
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md2, internal journal
i2c_adapter i2c-3: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-4: nForce2 SMBus adapter at 0x4c40
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
it87-isa 9191-0290: Detected broken BIOS defaults, disabling PWM interface
ACPI: PCI Interrupt 0000:05:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
Installing spdif_bug patch: Audigy 2 ZS [2001]
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: md4: found reiserfs format "3.6" with standard journal
ReiserFS: md4: using ordered data mode
ReiserFS: md4: journal params: device md4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md4: checking transaction log (md4)
ReiserFS: md4: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: hde1: found reiserfs format "3.6" with standard journal
ReiserFS: hde1: using ordered data mode
ReiserFS: hde1: journal params: device hde1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hde1: checking transaction log (hde1)
ReiserFS: hde1: Using r5 hash to sort names
ReiserFS: sde2: found reiserfs format "3.6" with standard journal
ReiserFS: sde2: using ordered data mode
ReiserFS: sde2: journal params: device sde2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sde2: checking transaction log (sde2)
ReiserFS: sde2: Using r5 hash to sort names
ReiserFS: sdg2: found reiserfs format "3.6" with standard journal
ReiserFS: sdg2: using ordered data mode
ReiserFS: sdg2: journal params: device sdg2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdg2: checking transaction log (sdg2)
ReiserFS: sdg2: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdi1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ip_tables: (C) 2000-2006 Netfilter Core Team
switch: Setting full-duplex based on MII#1 link partner capability of 8de1.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 312 bytes per conntrack
adsl: no IPv6 routers present
switch: no IPv6 routers present
dmesg for 2.6.19-rc4-mm1 without PATA drivers:
Linux version 2.6.19-rc4-mm1 (jurriaan@middle) (gcc version 4.1.2 20061028 (prerelease) (Debian 4.1.1-19)) #9 SMP Tue Oct 31 19:27:17 CET 2006
Command line: root=/dev/md2 video=nvidiafb:1600x1200-32@85
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c800 (usable)
BIOS-e820: 000000000009c800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000bfff0000 (usable)
BIOS-e820: 00000000bfff0000 - 00000000bfff3000 (ACPI NVS)
BIOS-e820: 00000000bfff3000 - 00000000c0000000 (ACPI data)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000140000000 (usable)
Entering add_active_range(0, 0, 156) 0 entries of 256 used
Entering add_active_range(0, 256, 786416) 1 entries of 256 used
Entering add_active_range(0, 1048576, 1310720) 2 entries of 256 used
end_pfn_map = 1310720
DMI 2.3 present.
ACPI: RSDP (v000 Nvidia ) @ 0x00000000000f7d30
ACPI: RSDT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff3040
ACPI: FADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff30c0
ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x00000000bfff9900
ACPI: SRAT (v001 AMD HAMMER 0x00000001 AMD 0x00000001) @ 0x00000000bfff9b80
ACPI: MCFG (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff9cc0
ACPI: MADT (v001 Nvidia AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x00000000bfff9840
ACPI: DSDT (v001 NVIDIA AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x0000000000000000
Entering add_active_range(0, 0, 156) 0 entries of 256 used
Entering add_active_range(0, 256, 786416) 1 entries of 256 used
Entering add_active_range(0, 1048576, 1310720) 2 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1310720
early_node_map[3] active PFN ranges
0: 0 -> 156
0: 256 -> 786416
0: 1048576 -> 1310720
On node 0 totalpages: 1048460
DMA zone: 56 pages used for memmap
DMA zone: 1841 pages reserved
DMA zone: 2099 pages, LIFO batch:0
DMA32 zone: 14280 pages used for memmap
DMA32 zone: 768040 pages, LIFO batch:31
Normal zone: 3584 pages used for memmap
Normal zone: 258560 pages, LIFO batch:31
Nvidia board detected. Ignoring ACPI timer override.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 (Bootup-CPU)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: BIOS IRQ0 pin2 override ignored.
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Setting APIC routing to flat
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009c000 - 000000000009d000
Nosave address range: 000000000009d000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000f0000
Nosave address range: 00000000000f0000 - 0000000000100000
Nosave address range: 00000000bfff0000 - 00000000bfff3000
Nosave address range: 00000000bfff3000 - 00000000c0000000
Nosave address range: 00000000c0000000 - 00000000e0000000
Nosave address range: 00000000e0000000 - 00000000f0000000
Nosave address range: 00000000f0000000 - 00000000fec00000
Nosave address range: 00000000fec00000 - 0000000100000000
Allocating PCI resources starting at c2000000 (gap: c0000000:20000000)
PERCPU: Allocating 31936 bytes of per cpu data
Built 1 zonelists. Total pages: 1028699
Kernel command line: root=/dev/md2 video=nvidiafb:1600x1200-32@85
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
CPU 0: aperture @ 8000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 8000000
Memory: 4042676k/5242880k available (3924k kernel code, 150952k reserved, 2389k data, 284k init)
Calibrating delay using timer specific routine.. 5042.57 BogoMIPS (lpj=2521288)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
Freeing SMP alternatives: 44k freed
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 13127938
Detected 13.127 MHz APIC timer.
Booting processor 1/2 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5040.43 BogoMIPS (lpj=2520217)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ stepping 01
CPU 1: Syncing TSC to CPU 0.
CPU 1: synchronized TSC with CPU 0 (last diff -76 cycles, maxerr 588 cycles)
Brought up 2 CPUs
testing NMI watchdog ... CPU#0: NMI appears to be stuck (111->116)!
CPU#1: NMI appears to be stuck (60->65)!
Disabling vsyscall due to use of PM timer
time.c: Using 3.579545 MHz WALL PM GTOD PM timer.
time.c: Detected 2520.562 MHz processor.
Uhhuh. NMI received for unknown reason 2d.
Do you have a strange power saving mode enabled?
Dazed and confused, but trying to continue
Uhhuh. NMI received for unknown reason 00.
Do you have a strange power saving mode enabled?
Dazed and confused, but trying to continue
migration_cost=161
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000
PCI: No mmconfig possible on device 00:18
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Transparent bridge - 0000:00:09.0
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LPCA] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCP] (IRQs 20 21 22 23) *0, disabled.
Generic PHY: Registered new driver
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 8000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
ieee1394: Initialized config rom entry `ip1394'
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:05:08.2[B] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[d900e000-d900e7ff] Max Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:05:0b.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
ohci1394: fw-host1: OHCI-1394 1.1 (PCI): IRQ=[16] MMIO=[d900d000-d900d7ff] Max Packet=[2048] IR/IT contexts=[4/8]
PCI: Bridge: 0000:00:09.0
IO window: 6000-afff
MEM window: d8000000-d9ffffff
PREFETCH window: da100000-da1fffff
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0c.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0d.0
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
PCI: Bridge: 0000:00:0e.0
IO window: disabled.
MEM window: d0000000-d7ffffff
PREFETCH window: c0000000-cfffffff
PCI: Setting latency timer of device 0000:00:09.0 to 64
PCI: Setting latency timer of device 0000:00:0b.0 to 64
PCI: Setting latency timer of device 0000:00:0c.0 to 64
PCI: Setting latency timer of device 0000:00:0d.0 to 64
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
Coda Kernel/Venus communications, v6.0.0, coda@cs.cmu.edu
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.27 [Flags: R/O].
io scheduler noop registered
io scheduler cfq registered (default)
PCI: Linking AER extended capability on 0000:00:0b.0
PCI: Linking AER extended capability on 0000:00:0c.0
PCI: Linking AER extended capability on 0000:00:0d.0
PCI: Linking AER extended capability on 0000:00:0e.0
PCI: Setting latency timer of device 0000:00:0b.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0b.0:pcie00]
Allocate Port Service[0000:00:0b.0:pcie03]
PCI: Setting latency timer of device 0000:00:0c.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0c.0:pcie00]
Allocate Port Service[0000:00:0c.0:pcie03]
PCI: Setting latency timer of device 0000:00:0d.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0d.0:pcie00]
Allocate Port Service[0000:00:0d.0:pcie03]
PCI: Setting latency timer of device 0000:00:0e.0 to 64
pcie_portdrv_probe->Dev[005d:10de] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:0e.0:pcie00]
Allocate Port Service[0000:00:0e.0:pcie03]
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
nvidiafb: Device ID: 10de0141
nvidiafb: CRTC0 analog found
nvidiafb: CRTC1 analog found
nvidiafb: EDID found from BUS2
nvidiafb: CRTC 0 appears to have a CRT attached
nvidiafb: Using CRT on CRTC 0
nvidiafb: MTRR set to ON
Console: switching to colour frame buffer device 160x66
nvidiafb: PCI nVidia NV14 framebuffer (64MB @ 0xC0000000)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Using specific hotkey driver
lp: driver loaded but no devices found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Hangcheck: starting hangcheck timer 0.9.0 (tick is 180 seconds, margin is 60 seconds).
Hangcheck: Using monotonic_clock().
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
ACPI: PCI Interrupt 0000:05:0c.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
skge 1.9 addr 0xd9008000 irq 17 chip Yukon-Lite rev 9
skge eth0: addr 00:15:f2:20:e6:69
Marvell 88E1101: Registered new driver
Davicom DM9161E: Registered new driver
Davicom DM9131: Registered new driver
Cicada Cis8204: Registered new driver
Cicada Cis8201: Registered new driver
LXT970: Registered new driver
LXT971: Registered new driver
QS6612: Registered new driver
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.59.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [APCH] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:0a.0 to 64
forcedeth: using HIGHDMA
eth1: forcedeth.c: subsystem: 01043:8141 bound to 0000:00:0a.0
Linux Tulip driver version 1.1.14 (May 11, 2002)
ACPI: PCI Interrupt 0000:05:07.0[A] -> Link [APC2] -> GSI 17 (level, low) -> IRQ 17
tulip0: MII transceiver #1 config 3100 status 7829 advertising 01e1.
eth2: Lite-On 82c168 PNIC rev 32 at Port 0x8800, 00:A0:CC:21:89:0C, IRQ 17.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
RocketRAID 3xxx SATA Controller driver v1.0 (060426)
libata version 2.00 loaded.
sata_sil 0000:05:0a.0: version 2.0
ACPI: PCI Interrupt 0000:05:0a.0[A] -> Link [APC4] -> GSI 19 (level, low) -> IRQ 19
sata_sil 0000:05:0a.0: Applying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xFFFFC20000056080 ctl 0xFFFFC2000005608A bmdma 0xFFFFC20000056000 irq 19
ata2: SATA max UDMA/100 cmd 0xFFFFC200000560C0 ctl 0xFFFFC200000560CA bmdma 0xFFFFC20000056008 irq 19
ata3: SATA max UDMA/100 cmd 0xFFFFC20000056280 ctl 0xFFFFC2000005628A bmdma 0xFFFFC20000056200 irq 19
ata4: SATA max UDMA/100 cmd 0xFFFFC200000562C0 ctl 0xFFFFC200000562CA bmdma 0xFFFFC20000056208 irq 19
scsi0 : sata_sil
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi1 : sata_sil
ieee1394: Host added: ID:BUS[0-01:1023] GUID[00023c014100f4bf]
ieee1394: Host added: ID:BUS[1-00:1023] GUID[0011d80000738f5d]
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/100
scsi2 : sata_sil
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata3.00: ata3: dev 0 multi count 16
ata3.00: configured for UDMA/100
scsi3 : sata_sil
ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata4.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 0/32)
ata4.00: ata4: dev 0 multi count 16
ata4.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
scsi 1:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1
sd 1:0:0:0: Attached scsi disk sdb
sd 1:0:0:0: Attached scsi generic sg1 type 0
scsi 2:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 488397168 512-byte hdwr sectors (250059 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
sdc: sdc1
sd 2:0:0:0: Attached scsi disk sdc
sd 2:0:0:0: Attached scsi generic sg2 type 0
scsi 3:0:0:0: Direct-Access ATA ST3250823AS 3.02 PQ: 0 ANSI: 5
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
SCSI device sdd: 488397168 512-byte hdwr sectors (250059 MB)
sdd: Write Protect is off
sdd: Mode Sense: 00 3a 00 00
SCSI device sdd: drive cache: write back
sdd: sdd1
sd 3:0:0:0: Attached scsi disk sdd
sd 3:0:0:0: Attached scsi generic sg3 type 0
sata_nv 0000:00:07.0: version 3.1
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:07.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:07.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata5: SATA max UDMA/133 cmd 0xFFFFC200100BC480 ctl 0xFFFFC200100BC4A0 bmdma 0xD800 irq 22
ata6: SATA max UDMA/133 cmd 0xFFFFC200100BC580 ctl 0xFFFFC200100BC5A0 bmdma 0xD808 irq 22
scsi4 : sata_nv
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 31/32)
ata5.00: ata5: dev 0 multi count 1
ata5.00: configured for UDMA/133
scsi5 : sata_nv
ata6: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata6.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32)
ata6.00: ata6: dev 0 multi count 1
ata6.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA ST3300622AS 3.AA PQ: 0 ANSI: 5
ata5: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sde: 586072368 512-byte hdwr sectors (300069 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: drive cache: write back
SCSI device sde: 586072368 512-byte hdwr sectors (300069 MB)
sde: Write Protect is off
sde: Mode Sense: 00 3a 00 00
SCSI device sde: drive cache: write back
sde: sde1 sde2
sd 4:0:0:0: Attached scsi disk sde
sd 4:0:0:0: Attached scsi generic sg4 type 0
scsi 5:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
ata6: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sdf: 488397168 512-byte hdwr sectors (250059 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: drive cache: write back
SCSI device sdf: 488397168 512-byte hdwr sectors (250059 MB)
sdf: Write Protect is off
sdf: Mode Sense: 00 3a 00 00
SCSI device sdf: drive cache: write back
sdf: sdf1
sd 5:0:0:0: Attached scsi disk sdf
sd 5:0:0:0: Attached scsi generic sg5 type 0
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:08.0: Using ADMA mode
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata7: SATA max UDMA/133 cmd 0xFFFFC200100BE480 ctl 0xFFFFC200100BE4A0 bmdma 0xC400 irq 21
ata8: SATA max UDMA/133 cmd 0xFFFFC200100BE580 ctl 0xFFFFC200100BE5A0 bmdma 0xC408 irq 21
scsi6 : sata_nv
ata7: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata7.00: ATA-7, max UDMA/133, 586072368 sectors: LBA48 NCQ (depth 31/32)
ata7.00: ata7: dev 0 multi count 1
ata7.00: configured for UDMA/133
scsi7 : sata_nv
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata8.00: ATA-7, max UDMA/133, 488397168 sectors: LBA48 NCQ (depth 31/32)
ata8.00: ata8: dev 0 multi count 1
ata8.00: configured for UDMA/133
scsi 6:0:0:0: Direct-Access ATA ST3300622AS 3.AA PQ: 0 ANSI: 5
ata7: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sdg: 586072368 512-byte hdwr sectors (300069 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: drive cache: write back
SCSI device sdg: 586072368 512-byte hdwr sectors (300069 MB)
sdg: Write Protect is off
sdg: Mode Sense: 00 3a 00 00
SCSI device sdg: drive cache: write back
sdg: sdg1 sdg2
sd 6:0:0:0: Attached scsi disk sdg
sd 6:0:0:0: Attached scsi generic sg6 type 0
scsi 7:0:0:0: Direct-Access ATA ST3250823AS 3.03 PQ: 0 ANSI: 5
ata8: bounce limit 0xFFFFFFFFFFFFFFFF, segment boundary 0xFFFFFFFF, hw segs 61
SCSI device sdh: 488397168 512-byte hdwr sectors (250059 MB)
sdh: Write Protect is off
sdh: Mode Sense: 00 3a 00 00
SCSI device sdh: drive cache: write back
SCSI device sdh: 488397168 512-byte hdwr sectors (250059 MB)
sdh: Write Protect is off
sdh: Mode Sense: 00 3a 00 00
SCSI device sdh: drive cache: write back
sdh: sdh1
sd 7:0:0:0: Attached scsi disk sdh
sd 7:0:0:0: Attached scsi generic sg7 type 0
pata_amd 0000:00:06.0: version 0.2.4
PCI: Setting latency timer of device 0000:00:06.0 to 64
ata9: PATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0xF000 irq 14
ata10: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xF008 irq 15
scsi8 : pata_amd
ata9.00: ATA-6, max UDMA/100, 390721968 sectors: LBA48
ata9.00: ata9: dev 0 multi count 1
ata9.01: ATAPI, max UDMA/33
ata9.00: configured for UDMA/100
ata9.01: configured for UDMA/33
scsi9 : pata_amd
ata10.00: ATA-6, max UDMA/100, 390721968 sectors: LBA48
ata10.00: ata10: dev 0 multi count 1
ata10.00: configured for UDMA/100
scsi 8:0:0:0: Direct-Access ATA WDC WD2000JB-32E 15.0 PQ: 0 ANSI: 5
SCSI device sdi: 390721968 512-byte hdwr sectors (200050 MB)
Losing some ticks... checking if CPU frequency changed.
sdi: Write Protect is off
sdi: Mode Sense: 00 3a 00 00
SCSI device sdi: drive cache: write back
SCSI device sdi: 390721968 512-byte hdwr sectors (200050 MB)
sdi: Write Protect is off
sdi: Mode Sense: 00 3a 00 00
SCSI device sdi: drive cache: write back
sdi: sdi1 sdi2 < sdi5 sdi6 sdi7 sdi8 sdi9 >
sd 8:0:0:0: Attached scsi disk sdi
sd 8:0:0:0: Attached scsi generic sg8 type 0
scsi 8:0:1:0: CD-ROM _NEC DVD_RW ND-3540A 1.01 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 8:0:1:0: Attached scsi CD-ROM sr0
sr 8:0:1:0: Attached scsi generic sg9 type 5
scsi 9:0:0:0: Direct-Access ATA WDC WD2000JB-00F 15.0 PQ: 0 ANSI: 5
SCSI device sdj: 390721968 512-byte hdwr sectors (200050 MB)
sdj: Write Protect is off
sdj: Mode Sense: 00 3a 00 00
SCSI device sdj: drive cache: write back
SCSI device sdj: 390721968 512-byte hdwr sectors (200050 MB)
sdj: Write Protect is off
sdj: Mode Sense: 00 3a 00 00
SCSI device sdj: drive cache: write back
sdj: sdj1 sdj2 < sdj5 sdj6 sdj7 sdj8 sdj9 >
sd 9:0:0:0: Attached scsi disk sdj
sd 9:0:0:0: Attached scsi generic sg10 type 0
pata_hpt37x: BIOS has not set timing clocks.
hpt37x: HPT374: Bus clock 33MHz.
ACPI: PCI Interrupt 0000:05:06.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
ata11: PATA max UDMA/133 cmd 0x6000 ctl 0x6402 bmdma 0x7000 irq 16
ata12: PATA max UDMA/133 cmd 0x6800 ctl 0x6C02 bmdma 0x7008 irq 16
scsi10 : pata_hpt37x
ata11.00: ATA-6, max UDMA/100, 488397168 sectors: LBA48
ata11.00: ata11: dev 0 multi count 16
ata11.01: failed to IDENTIFY (I/O error, err_mask=0x1)
ata11: failed to recover some devices, retrying in 5 secs
ata11.01: failed to IDENTIFY (I/O error, err_mask=0x1)
ata11: failed to recover some devices, retrying in 5 secs
ata11.01: failed to IDENTIFY (I/O error, err_mask=0x1)
ata11: failed to recover some devices, retrying in 5 secs
Find mode for 12 reports A81F442
Find mode for DMA 69 reports 12848242
ata11.00: configured for UDMA/100
scsi11 : pata_hpt37x
ATA: abnormal status 0x8 on port 0x6807
scsi 10:0:0:0: Direct-Access ATA WDC WD2500JB-00F 15.0 PQ: 0 ANSI: 5
SCSI device sdk: 488397168 512-byte hdwr sectors (250059 MB)
sdk: Write Protect is off
sdk: Mode Sense: 00 3a 00 00
SCSI device sdk: drive cache: write back
SCSI device sdk: 488397168 512-byte hdwr sectors (250059 MB)
sdk: Write Protect is off
sdk: Mode Sense: 00 3a 00 00
SCSI device sdk: drive cache: write back
sdk: sdk1
sd 10:0:0:0: Attached scsi disk sdk
sd 10:0:0:0: Attached scsi generic sg11 type 0
pata_hpt37x: BIOS has not set timing clocks.
hpt37x: HPT374: Bus clock 33MHz.
ACPI: PCI Interrupt 0000:05:06.1[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 16
ata13: PATA max UDMA/133 cmd 0x7400 ctl 0x7802 bmdma 0x8400 irq 16
ata14: PATA max UDMA/133 cmd 0x7C00 ctl 0x8002 bmdma 0x8408 irq 16
scsi12 : pata_hpt37x
ata13.00: ATA-7, max UDMA/100, 586072368 sectors: LBA48
ata13.00: ata13: dev 0 multi count 16
Find mode for 12 reports A81F442
Find mode for DMA 69 reports 12848242
ata13.00: configured for UDMA/100
scsi13 : pata_hpt37x
ATA: abnormal status 0x8 on port 0x7C07
scsi 12:0:0:0: Direct-Access ATA ST3300831A 3.01 PQ: 0 ANSI: 5
SCSI device sdl: 586072368 512-byte hdwr sectors (300069 MB)
sdl: Write Protect is off
sdl: Mode Sense: 00 3a 00 00
SCSI device sdl: drive cache: write back
SCSI device sdl: 586072368 512-byte hdwr sectors (300069 MB)
sdl: Write Protect is off
sdl: Mode Sense: 00 3a 00 00
SCSI device sdl: drive cache: write back
sdl: sdl1
sd 12:0:0:0: Attached scsi disk sdl
sd 12:0:0:0: Attached scsi generic sg12 type 0
video1394: Installed video1394 module
ieee1394: raw1394: /dev/raw1394 device initialized
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCL] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:02.1 to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.1
ehci_hcd 0000:00:02.1: irq 20, io mem 0xfeb00000
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.19-rc4-mm1 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.1
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 23, io mem 0xda004000
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.19-rc4-mm1 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int64x1 2339 MB/s
raid6: int64x2 3156 MB/s
raid6: int64x4 2992 MB/s
raid6: int64x8 2070 MB/s
raid6: sse2x1 2386 MB/s
raid6: sse2x2 3367 MB/s
raid6: sse2x4 3929 MB/s
raid6: using algorithm sse2x4 (3929 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: automatically using best checksumming function: generic_sse
generic_sse: 8040.000 MB/sec
raid5: using function: generic_sse (8040.000 MB/sec)
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
NET: Registered protocol family 8
NET: Registered protocol family 20
powernow-k8: Found 2 AMD Athlon(tm) 64 X2 Dual Core Processor 4600+ processors (version 2.00.00)
powernow-k8: 0 : fid 0x10 (2400 MHz), vid 0x8
powernow-k8: 1 : fid 0xe (2200 MHz), vid 0xa
powernow-k8: 2 : fid 0xc (2000 MHz), vid 0xc
powernow-k8: 3 : fid 0xa (1800 MHz), vid 0xe
powernow-k8: 4 : fid 0x2 (1000 MHz), vid 0x12
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
logips2pp: Detected unknown logitech mouse model 1
input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdj9 ...
md: adding sdj9 ...
md: sdj8 has different UUID to sdj9
md: sdj7 has different UUID to sdj9
md: sdj6 has different UUID to sdj9
md: sdj5 has different UUID to sdj9
md: adding sdi9 ...
md: sdi8 has different UUID to sdj9
md: sdi7 has different UUID to sdj9
md: sdi6 has different UUID to sdj9
md: sdi5 has different UUID to sdj9
md: sdh1 has different UUID to sdj9
md: sdg1 has different UUID to sdj9
md: sdf1 has different UUID to sdj9
md: sde1 has different UUID to sdj9
md: sdd1 has different UUID to sdj9
md: sdc1 has different UUID to sdj9
md: sdb1 has different UUID to sdj9
md: sda1 has different UUID to sdj9
md: created md4
md: bind<sdi9>
md: bind<sdj9>
md: running: <sdj9><sdi9>
raid1: raid set md4 active with 2 out of 2 mirrors
md4: bitmap initialized from disk: read 10/10 pages, set 48 bits, status: 0
created bitmap (156 pages) for device md4
md: considering sdj8 ...
md: adding sdj8 ...
md: sdj7 has different UUID to sdj8
md: sdj6 has different UUID to sdj8
md: sdj5 has different UUID to sdj8
md: adding sdi8 ...
md: sdi7 has different UUID to sdj8
md: sdi6 has different UUID to sdj8
md: sdi5 has different UUID to sdj8
md: sdh1 has different UUID to sdj8
md: sdg1 has different UUID to sdj8
md: sdf1 has different UUID to sdj8
md: sde1 has different UUID to sdj8
md: sdd1 has different UUID to sdj8
md: sdc1 has different UUID to sdj8
md: sdb1 has different UUID to sdj8
md: sda1 has different UUID to sdj8
md: created md3
md: bind<sdi8>
md: bind<sdj8>
md: running: <sdj8><sdi8>
raid1: raid set md3 active with 2 out of 2 mirrors
md3: bitmap initialized from disk: read 8/8 pages, set 6 bits, status: 0
created bitmap (123 pages) for device md3
md: considering sdj7 ...
md: adding sdj7 ...
md: sdj6 has different UUID to sdj7
md: sdj5 has different UUID to sdj7
md: adding sdi7 ...
md: sdi6 has different UUID to sdj7
md: sdi5 has different UUID to sdj7
md: sdh1 has different UUID to sdj7
md: sdg1 has different UUID to sdj7
md: sdf1 has different UUID to sdj7
md: sde1 has different UUID to sdj7
md: sdd1 has different UUID to sdj7
md: sdc1 has different UUID to sdj7
md: sdb1 has different UUID to sdj7
md: sda1 has different UUID to sdj7
md: created md2
md: bind<sdi7>
md: bind<sdj7>
md: running: <sdj7><sdi7>
raid1: raid set md2 active with 2 out of 2 mirrors
md2: bitmap initialized from disk: read 8/8 pages, set 91 bits, status: 0
created bitmap (123 pages) for device md2
md: considering sdj6 ...
md: adding sdj6 ...
md: sdj5 has different UUID to sdj6
md: adding sdi6 ...
md: sdi5 has different UUID to sdj6
md: sdh1 has different UUID to sdj6
md: sdg1 has different UUID to sdj6
md: sdf1 has different UUID to sdj6
md: sde1 has different UUID to sdj6
md: sdd1 has different UUID to sdj6
md: sdc1 has different UUID to sdj6
md: sdb1 has different UUID to sdj6
md: sda1 has different UUID to sdj6
md: created md1
md: bind<sdi6>
md: bind<sdj6>
md: running: <sdj6><sdi6>
raid1: raid set md1 active with 2 out of 2 mirrors
md1: bitmap initialized from disk: read 12/12 pages, set 40 bits, status: 0
created bitmap (184 pages) for device md1
md: considering sdj5 ...
md: adding sdj5 ...
md: adding sdi5 ...
md: sdh1 has different UUID to sdj5
md: sdg1 has different UUID to sdj5
md: sdf1 has different UUID to sdj5
md: sde1 has different UUID to sdj5
md: sdd1 has different UUID to sdj5
md: sdc1 has different UUID to sdj5
md: sdb1 has different UUID to sdj5
md: sda1 has different UUID to sdj5
md: created md5
md: bind<sdi5>
md: bind<sdj5>
md: running: <sdj5><sdi5>
raid1: raid set md5 active with 2 out of 2 mirrors
md5: bitmap initialized from disk: read 9/9 pages, set 0 bits, status: 0
created bitmap (129 pages) for device md5
md: considering sdh1 ...
md: adding sdh1 ...
md: adding sdg1 ...
md: adding sdf1 ...
md: adding sde1 ...
md: adding sdd1 ...
md: adding sdc1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: bind<sdc1>
md: bind<sdd1>
md: bind<sde1>
md: bind<sdf1>
md: bind<sdg1>
md: bind<sdh1>
md: running: <sdh1><sdg1><sdf1><sde1><sdd1><sdc1><sdb1><sda1>
raid5: device sdh1 operational as raid disk 1
raid5: device sdg1 operational as raid disk 0
raid5: device sdf1 operational as raid disk 5
raid5: device sde1 operational as raid disk 6
raid5: device sdd1 operational as raid disk 7
raid5: device sdc1 operational as raid disk 3
raid5: device sdb1 operational as raid disk 2
raid5: device sda1 operational as raid disk 4
raid5: allocated 8462kB for md0
raid5: raid level 6 set md0 active with 8 out of 8 devices, algorithm 2
RAID5 conf printout:
--- rd:8 wd:8
disk 0, o:1, dev:sdg1
disk 1, o:1, dev:sdh1
disk 2, o:1, dev:sdb1
disk 3, o:1, dev:sdc1
disk 4, o:1, dev:sda1
disk 5, o:1, dev:sdf1
disk 6, o:1, dev:sde1
disk 7, o:1, dev:sdd1
md0: bitmap initialized from disk: read 15/15 pages, set 1 bits, status: 0
created bitmap (233 pages) for device md0
md: ... autorun DONE.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 284k freed
Adding 4200888k swap on /dev/md5. Priority:-1 extents:1 across:4200888k
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md2, internal journal
i2c_adapter i2c-3: nForce2 SMBus adapter at 0x4c00
i2c_adapter i2c-4: nForce2 SMBus adapter at 0x4c40
it87: Found IT8712F chip at 0x290, revision 7
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
it87-isa 9191-0290: Detected broken BIOS defaults, disabling PWM interface
ACPI: PCI Interrupt 0000:05:08.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 18
Installing spdif_bug patch: Audigy 2 ZS [2001]
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on md3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: md4: found reiserfs format "3.6" with standard journal
ReiserFS: md4: using ordered data mode
ReiserFS: md4: journal params: device md4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md4: checking transaction log (md4)
ReiserFS: md4: Using r5 hash to sort names
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ReiserFS: sde2: found reiserfs format "3.6" with standard journal
ReiserFS: sde2: using ordered data mode
ReiserFS: sde2: journal params: device sde2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sde2: checking transaction log (sde2)
ReiserFS: sde2: Using r5 hash to sort names
ReiserFS: sdg2: found reiserfs format "3.6" with standard journal
ReiserFS: sdg2: using ordered data mode
ReiserFS: sdg2: journal params: device sdg2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: sdg2: checking transaction log (sdg2)
ReiserFS: sdg2: Using r5 hash to sort names
ip_tables: (C) 2000-2006 Netfilter Core Team
switch: Setting full-duplex based on MII#1 link partner capability of 8de1.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 312 bytes per conntrack
switch: no IPv6 routers present
adsl: no IPv6 routers present
--
"Besides," she added with a shrug, "strategy and tactics are anathema
to the Apocalypse."
Steven Erikson - Deadhouse Gates
Debian (Unstable) GNU/Linux 2.6.18-mm3 2x5042 bogomips load 2.04
next reply other threads:[~2006-10-31 18:59 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-10-31 18:59 jurriaan [this message]
2006-10-31 19:22 ` scary message 'failed to recover some devices ... retrying' HPT370 Alan Cox
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20061031185921.GA3636@amd64.of.nowhere \
--to=thunder7@xs4all.nl \
--cc=alan@lxorguk.ukuu.org.uk \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.