From: "Kok, Auke" <auke-jan.h.kok@intel.com>
To: "Garzik, Jeff" <jgarzik@pobox.com>
Cc: netdev@vger.kernel.org, "Brandeburg,
Jesse" <jesse.brandeburg@intel.com>,
"Kok, Auke" <auke-jan.h.kok@intel.com>,
"Kok, Auke" <auke@foo-projects.org>,
"Ronciak, John" <john.ronciak@intel.com>
Subject: [PATCH 06/18] e1000: fix VR powerdown code
Date: Wed, 01 Nov 2006 09:51:42 -0800 [thread overview]
Message-ID: <20061101175142.2356.85600.stgit@gitlost.site> (raw)
In-Reply-To: <20061101175043.2356.13659.stgit@gitlost.site>
On ich systems during PHY power down to D3, the voltage regulators
were left on.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
---
drivers/net/e1000/e1000_hw.c | 9 +++++----
drivers/net/e1000/e1000_hw.h | 1 +
2 files changed, 6 insertions(+), 4 deletions(-)
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c
index a0a3c7e..a45685c 100644
--- a/drivers/net/e1000/e1000_hw.c
+++ b/drivers/net/e1000/e1000_hw.c
@@ -3942,14 +3942,15 @@ e1000_phy_powerdown_workaround(struct e1
E1000_WRITE_REG(hw, PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE |
E1000_PHY_CTRL_NOND0A_GBE_DISABLE);
- /* Write VR power-down enable */
+ /* Write VR power-down enable - bits 9:8 should be 10b */
e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data);
- e1000_write_phy_reg(hw, IGP3_VR_CTRL, phy_data |
- IGP3_VR_CTRL_MODE_SHUT);
+ phy_data |= (1 << 9);
+ phy_data &= ~(1 << 8);
+ e1000_write_phy_reg(hw, IGP3_VR_CTRL, phy_data);
/* Read it back and test */
e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data);
- if ((phy_data & IGP3_VR_CTRL_MODE_SHUT) || retry)
+ if (((phy_data & IGP3_VR_CTRL_MODE_MASK) == IGP3_VR_CTRL_MODE_SHUT) || retry)
break;
/* Issue PHY reset and repeat at most one more time */
diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h
index b32a0c3..31bea32 100644
--- a/drivers/net/e1000/e1000_hw.h
+++ b/drivers/net/e1000/e1000_hw.h
@@ -3173,6 +3173,7 @@ struct e1000_host_command_info {
#define IGP3_VR_CTRL \
PHY_REG(776, 18) /* Voltage regulator control register */
#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */
+#define IGP3_VR_CTRL_MODE_MASK 0x0300 /* Shutdown VR Mask */
#define IGP3_CAPABILITY \
PHY_REG(776, 19) /* IGP3 Capability Register */
---
Auke Kok <auke-jan.h.kok@intel.com>
next prev parent reply other threads:[~2006-11-01 17:44 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-11-01 17:50 [PATCH 00/18] e1000: features, updates, documentation Kok, Auke
2006-11-01 17:51 ` [PATCH 01/18] e1000: whitespace changes, comments, typos Kok, Auke
2006-11-01 17:51 ` [PATCH 02/18] e1000: Remove DISABLE_MULR debug code Kok, Auke
2006-11-01 17:51 ` [PATCH 03/18] e1000: FIX: enable hw TSO for IPV6 Kok, Auke
2006-11-01 17:51 ` [PATCH 04/18] e1000: Enble early receive (ERT) on 82573 Kok, Auke
2006-11-01 17:51 ` [PATCH 05/18] e1000: add mmiowb() for IA64 to sync tail writes Kok, Auke
2006-11-01 17:51 ` Kok, Auke [this message]
2006-11-01 17:51 ` [PATCH 07/18] e1000: reorder pci-e infor struct Kok, Auke
2006-11-01 17:51 ` [PATCH 08/18] e1000: simplify skb_put call Kok, Auke
2006-11-01 17:51 ` [PATCH 09/18] e1000: Remove unneeded and unwanted memsets Kok, Auke
2006-11-01 17:51 ` [PATCH 10/18] e1000: New hardware support Kok, Auke
2006-11-01 17:51 ` [PATCH 11/18] e1000: add queue restart counter Kok, Auke
2006-11-01 17:51 ` [PATCH 12/18] e1000: rename ICH8 flash macros Kok, Auke
2006-11-01 17:51 ` [PATCH 13/18] e1000: Only set IDE for tx when we are using TIDV/TADV Kok, Auke
2006-11-01 17:52 ` [PATCH 14/18] e1000: reorder e1000_param.c Kok, Auke
2006-11-01 17:52 ` [PATCH 15/18] e1000: add dynamic generic MSI interrupt routine Kok, Auke
2006-11-01 17:52 ` [PATCH 16/18] e1000: add dynamic itr modes Kok, Auke
2006-11-01 17:52 ` [PATCH 17/18] e1000: increment version to 7.3.15-k2 Kok, Auke
2006-11-01 17:52 ` [PATCH 18/18] e1000: update README for e1000 Kok, Auke
2006-11-06 8:08 ` [PATCH 00/18] e1000: features, updates, documentation Jeff Garzik
2006-11-06 15:23 ` Auke Kok
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20061101175142.2356.85600.stgit@gitlost.site \
--to=auke-jan.h.kok@intel.com \
--cc=auke@foo-projects.org \
--cc=jesse.brandeburg@intel.com \
--cc=jgarzik@pobox.com \
--cc=john.ronciak@intel.com \
--cc=netdev@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.