From: Tony Lindgren <tony@atomide.com>
To: "Marek Vašut" <marek.vasut@gmail.com>
Cc: linux-omap-open-source@linux.omap.com
Subject: Re: [PATCH 1/4] ARM: OMAP: Palm Tungsten|T defconfig
Date: Thu, 16 Nov 2006 03:48:49 +0200 [thread overview]
Message-ID: <20061116014849.GP21064@atomide.com> (raw)
In-Reply-To: <200611120037.58048.marek.vasut@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 367 bytes --]
Hi,
* Marek Vašut <marek.vasut@gmail.com> [061112 01:48]:
> Hi,
>
> I hope this time it'll be all ok ;-) (including formating)
>
> This adds defconfig for Palm Tungsten|T.
Thanks, pushing your four patches, but had to still do formatting
for tabs and trailing whitespace, see below.. You may want to check
your editor settings :)
Regards,
Tony
[-- Attachment #2: errors --]
[-- Type: text/plain, Size: 8301 bytes --]
Tabifying non-tabbed line: "+ .name = "write8k","
Tabifying non-tabbed line: "+ .offset = 0,"
Tabifying non-tabbed line: "+ .size = SZ_8K,"
Tabifying non-tabbed line: "+ .mask_flags = 0,"
Tabifying non-tabbed line: "+ .name = "PalmOS-BootLoader(ro)","
Tabifying non-tabbed line: "+ .offset = SZ_8K,"
Tabifying non-tabbed line: "+ .size = 7*SZ_8K,"
Tabifying non-tabbed line: "+ .mask_flags = MTD_WRITEABLE,"
Tabifying non-tabbed line: "+ .name = "u-boot","
Tabifying non-tabbed line: "+ .offset = MTDPART_OFS_APPEND,"
Tabifying non-tabbed line: "+ .size = 8*SZ_8K,"
Tabifying non-tabbed line: "+ .mask_flags = 0,"
Tabifying non-tabbed line: "+ .name = "PalmOS-FS(ro)","
Tabifying non-tabbed line: "+ .offset = MTDPART_OFS_APPEND,"
Tabifying non-tabbed line: "+ .size = 7*SZ_1M + 4*SZ_64K - 16*SZ_8K,"
Tabifying non-tabbed line: "+ .mask_flags = MTD_WRITEABLE,"
Tabifying non-tabbed line: "+ .name = "u-boot(rez)","
Tabifying non-tabbed line: "+ .offset = MTDPART_OFS_APPEND,"
Tabifying non-tabbed line: "+ .size = SZ_128K,"
Tabifying non-tabbed line: "+ .mask_flags = 0"
Tabifying non-tabbed line: "+ .name = "empty","
Tabifying non-tabbed line: "+ .offset = MTDPART_OFS_APPEND,"
Tabifying non-tabbed line: "+ .size = MTDPART_SIZ_FULL,"
Tabifying non-tabbed line: "+ .mask_flags = 0"
Removing trailing whitespace: "+static struct omap_mcbsp_reg_cfg mcbsp_regs = { "
Tabifying non-tabbed line: "+ RWDLEN2(OMAP_MCBSP_WORD_16) | RDATDLY(0),"
Tabifying non-tabbed line: "+ RWDLEN1(OMAP_MCBSP_WORD_16),"
Tabifying non-tabbed line: "+ XWDLEN2(OMAP_MCBSP_WORD_16) | XDATDLY(0) | XFIG,"
Tabifying non-tabbed line: "+ XWDLEN1(OMAP_MCBSP_WORD_16),"
Tabifying non-tabbed line: "+ FPER(DEFAULT_BITPERSAMPLE * 2 - 1),"
Removing trailing whitespace: "+ .get_default_samplerate = NULL, // aic23_get_default_samplerate, "
Removing trailing whitespace: "+ "
Tabifying non-tabbed line: "+ .start = INT_UART3,"
Tabifying non-tabbed line: "+ .end = INT_UART3,"
Tabifying non-tabbed line: "+ .flags = IORESOURCE_IRQ,"
Removing trailing whitespace: "+ "
Removing trailing whitespace: "+ "
Removing trailing whitespace: "+ "
Removing trailing whitespace: "+ "
Tabifying non-tabbed line: "+ /* MicroWire (bus 2) CS0 has an ads7846e */"
Tabifying non-tabbed line: "+ .modalias = "ads7846","
Tabifying non-tabbed line: "+ .platform_data = &palmtt_ts_info,"
Tabifying non-tabbed line: "+ .irq = OMAP_GPIO_IRQ(6),"
Tabifying non-tabbed line: "+ .max_speed_hz = 120000 /* max sample rate at 3V */"
Tabifying non-tabbed line: "+ * 26 /* command + data + overhead */,"
Tabifying non-tabbed line: "+ .bus_num = 2,"
Tabifying non-tabbed line: "+ .chip_select = 0,"
Removing trailing whitespace: "+ "
Tabifying non-tabbed line: "+ { OMAP_TAG_UART, &palmtt_uart_config },"
Removing trailing whitespace: "+ "
Tabifying non-tabbed line: "+ if (mode)"
Tabifying non-tabbed line: "+ omap_writew(0x8000, OMAP_WDT_TIMER_MODE);"
Tabifying non-tabbed line: "+ else {"
Tabifying non-tabbed line: "+ omap_writew(0x00f5, OMAP_WDT_TIMER_MODE);"
Tabifying non-tabbed line: "+ omap_writew(0x00f5, OMAP_WDT_TIMER_MODE);"
Tabifying non-tabbed line: "+ omap_writew(0x00a0, OMAP_WDT_TIMER_MODE);"
Tabifying non-tabbed line: "+ omap_writew(0x00a0, OMAP_WDT_TIMER_MODE);"
Tabifying non-tabbed line: "+ }"
Tabifying non-tabbed line: "+ omap_mpu_wdt_mode(0);"
Tabifying non-tabbed line: "+ omap_board_config_size = ARRAY_SIZE(palmtt_config);"
Tabifying non-tabbed line: "+ spi_register_board_info(palmtt_boardinfo,ARRAY_SIZE(palmtt_boardinfo));"
Removing trailing whitespace: "+ "
Tabifying non-tabbed line: "+ struct omapfb_device *fbdev)"
Tabifying non-tabbed line: "+ .name = "palmtt","
Tabifying non-tabbed line: "+ .config = OMAP_LCDC_PANEL_TFT | OMAP_LCDC_INV_VSYNC |"
Tabifying non-tabbed line: "+ OMAP_LCDC_INV_HSYNC | OMAP_LCDC_HSVS_RISING_EDGE |"
Tabifying non-tabbed line: "+ OMAP_LCDC_INV_HSYNC | OMAP_LCDC_HSVS_RISING_EDGE |"
Tabifying non-tabbed line: "+ OMAP_LCDC_HSVS_OPPOSITE,"
Tabifying non-tabbed line: "+ OMAP_LCDC_HSVS_OPPOSITE,"
Tabifying non-tabbed line: "+ .bpp = 16,"
Tabifying non-tabbed line: "+ .x_res = 320,"
Tabifying non-tabbed line: "+ .y_res = 320,"
Tabifying non-tabbed line: "+ .hsw = 4,"
Tabifying non-tabbed line: "+ .hfp = 8,"
Tabifying non-tabbed line: "+ .hbp = 28,"
Tabifying non-tabbed line: "+ .vsw = 1,"
Tabifying non-tabbed line: "+ .vfp = 8,"
Tabifying non-tabbed line: "+ .vbp = 7,"
Tabifying non-tabbed line: "+ .pcd = 0,"
Tabifying non-tabbed line: "+ .init = palmtt_panel_init,"
Tabifying non-tabbed line: "+ .enable = palmtt_panel_enable,"
Tabifying non-tabbed line: "+ .probe = palmtt_panel_probe,"
Tabifying non-tabbed line: "+ .remove = palmtt_panel_remove,"
Tabifying non-tabbed line: "+ .resume = palmtt_panel_resume,"
Tabifying non-tabbed line: "+ .driver = {"
Tabifying non-tabbed line: "+ .name = "lcd_palmtt","
Tabifying non-tabbed line: "+ .owner = THIS_MODULE,"
Tabifying non-tabbed line: "+ .spcr2 = FREE | FRST | GRST | XRST | XINTM(3),"
Tabifying non-tabbed line: "+ .spcr1 = RINTM(3) | RRST,"
Tabifying non-tabbed line: "+ .rcr2 = RPHASE | RFRLEN2(OMAP_MCBSP_WORD_8) |"
Tabifying non-tabbed line: "+ RWDLEN2(OMAP_MCBSP_WORD_16) | RDATDLY(0),"
Tabifying non-tabbed line: "+ RWDLEN2(OMAP_MCBSP_WORD_16) | RDATDLY(0),"
Tabifying non-tabbed line: "+ .rcr1 = RFRLEN1(OMAP_MCBSP_WORD_8) | RWDLEN1(OMAP_MCBSP_WORD_16),"
Tabifying non-tabbed line: "+ .xcr2 = XPHASE | XFRLEN2(OMAP_MCBSP_WORD_8) |"
Tabifying non-tabbed line: "+ XWDLEN2(OMAP_MCBSP_WORD_16) | XDATDLY(0) | XFIG,"
Tabifying non-tabbed line: "+ XWDLEN2(OMAP_MCBSP_WORD_16) | XDATDLY(0) | XFIG,"
Tabifying non-tabbed line: "+ .xcr1 = XFRLEN1(OMAP_MCBSP_WORD_8) | XWDLEN1(OMAP_MCBSP_WORD_16),"
Tabifying non-tabbed line: "+ .srgr1 = FWID(DEFAULT_BITPERSAMPLE - 1),"
Tabifying non-tabbed line: "+ .srgr2 = GSYNC | CLKSP | FSGM | FPER(DEFAULT_BITPERSAMPLE * 2 - 1),"
Tabifying non-tabbed line: "+ .pcr0 = CLKXP | CLKRP, /* mcbsp: slave */"
Tabifying non-tabbed line: "+ {"
Tabifying non-tabbed line: "+ .irq = OMAP_GPIO_IRQ(PALMZ71_PENIRQ_GPIO),"
Tabifying non-tabbed line: "+ * 26 /* command + data + overhead */,"
Tabifying non-tabbed line: "+ * 26 /* command + data + overhead */,"
Tabifying non-tabbed line: "+ }"
Tabifying non-tabbed line: "+ palmz71_powercable, SA_SAMPLE_RANDOM, "palmz71-cable", 0))"
Tabifying non-tabbed line: "+ palmz71_powercable, SA_SAMPLE_RANDOM, "palmz71-cable", 0))"
Tabifying non-tabbed line: "+ printk(KERN_ERR"
Tabifying non-tabbed line: "+ "IRQ request for power cable failed!\n");"
[-- Attachment #3: Type: text/plain, Size: 0 bytes --]
prev parent reply other threads:[~2006-11-16 1:48 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2006-11-11 23:37 [PATCH 1/4] ARM: OMAP: Palm Tungsten|T defconfig Marek Vašut
2006-11-16 1:48 ` Tony Lindgren [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20061116014849.GP21064@atomide.com \
--to=tony@atomide.com \
--cc=linux-omap-open-source@linux.omap.com \
--cc=marek.vasut@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.